Error msg "no modem found!" when trying to connect...

Hi.
I'm getting this error message when I tried to connect to N95 via bluetooth as modem, using "One Touch Access". I can use "One Touch Access" to connect with N95 via USB cable, though.
My hardware is:
Toshiba R150 laptop;
Generic bluetooth adaptor with IVT BlueSoleil as driver;
Windows SP2;
PC Suite 6.86.9.3;
Nokia N95
Any solution?

hi,
i know you want bluetooth, but cable is really much better ya know...
but if you insist on BT, well couple of thing i could suggest:
test and make sure that BT is working properly, you can do this by sending files via bt on both ways
make the N95 as default modem, then goto it and query it, just to make sure it is working well...
thats all i could think of at the moment...

Similar Messages

  • No receivers found when trying to connect to directv?

    No receivers found when trying to connect to directv

    Are your receivers connected to the internet?
    If so did you try the Settings area of the DirecTV to Validate the IP address of the receiver?

  • Error message WMC604 in VZAM when trying to connect to 4G using Novatel USB551L.

    VZAM recognizes the modem, and attempts to connect to 4G. After about 10 seconds, a message appears,"Error WMC604, Device could not establish a connection". (I have no problem connecting to 3G, just 4G)
    One clue: If I have "Control Panel>Network Connections>Novotel 551L open when I try to connect, I can watch (if I am connecting to 3G) the modem aquire an IP address and connect. If I am connecting to 4G, there is no such activity shown on Control Panel>Network Connections>Novatel 551L modem. It just does nothing until the error message appears in VZAM. It's as if VZAM is not communicating with the modem although during this time VZAM displays a message "connecting".
     I have created a dial-up connection in Windows 7 according to the Verizon knowledge base article ID=29355 just so I could use 4G, and the modem connects and works just fine. I just wish I get it to connect to 4G using VZAM.
     I am using VZAM version v7.6.3.1(2642f) and one of the things that VZ tech support suggested was replace the SIM card, but that didn't make any difference. I am using Dell XPS 8300 desktop running Win 7 Home Premium,SP1 currently, although problem is the same on my Dell 5160 laptop running Win XP, SP3.
    Hoping someone here on this board can help. I have spent hours on the phone with Verizon tech support and they say they have never heard of this error, and have no clue how to make it go away. In checking Google, I see that it is in fact a fairly common error in VZAM, but no one seems to know how to fix it......Verizon reps on the board feel free to come to my rescue?
    HELP!!!!

    AdamE_VZW
    Thank you for your reply. I checked Device Manager for conflicts and see none. I opened VZAM and Device Manager>Novatel Modem side-by-side on the screen and attemped to connect to 4G using VZAM while watching Device Manager for conflicts. There were none indicated when the WMC604 error appeared in VZAM. According to Device Manager, my Novatel modem driver is version 1.1.12.0 ; dated 12/8/10. The "update driver" button is grayed out so I don't know how to check for a newer version. This version is the one that came on the VZAM install CD I belive.
    Some background about this problem: When I first got this modem and installed the software, it worked as it should. It came up in Global mode and connected to a weak 4G signal that was comming from the Portland OR airport. Because the signal was weak and un-reliable, the modem would constantly shift back to 3G, and then every few minutes back to 4G, over and over. I got tired of putting up with the constant hunting, and, using the diagnostic screen, locked it into EVDO mode until 4G went live in Portland OR in the middle of June. During the time it was in EVDO (3G) mode, I had no problem connecting to 3G using VZAM. When Portland went live, I locked it back to LTE mode, and that was when I discovered the error WMC604 message. This was using my previous computer, a Dell Dimension 4500 desktop, Win XP,SP3, and an external Wilson log-periodic tri-band antenna.  Since Portland went live, my current RSSI for 4G runs around -68db, and SINR varies between -9 to -12 db.
    I recently got my present computer, a Dell XPS-8300 desktop, Core i7, Win 7 Home Premium, SP1. I did a fresh install of VZAM on this new computer using the CD that came with the USB551L modem and then checked online (using 3G) for VZAM updates. It says I have the latest version.  The problem is exactly the same on the new computer as it was on my other 2 computers. That tells me that the problem must lie with the modem firmware or hardware, because the problem follows the modem, no matter what computer it is hooked up to. I even took it back to the Verizon store where I got it and they hooked it up to one of their computers and got the same error message when trying to connect to 4G. 3G worked properly
    As I mentioned before, the modem instantly connects to 4G using the Win 7 dial-up connection I created and gives pretty good speeds, about 10MB down and 4-5MB up, according to SpeedCheck.com.
    I can use it the way it is, it is just frustrating that it won't work using VZAM.
    Thank you for your attention and help,
    Inst_Tech

  • Internal error 17001 on win32 XP when trying to connect to DB

    Hi,
    I'm trying to connect to a DB via TNS. Connection failes, window pops up saying that internal error occured, fetching of error msg failed, manufacture code 17001.
    History:
    - solving java path error "no ocijdbc11 in java.library.path" by installation of client 11.2, setting PATH variable to that installation, and setting path to tns name dir where TNSNAV.ORA file is located (which complied to %ORACLE_HOME%\network\admin, with ORACLE_HOME variable specified in win registry HKEY_LOCAL_MACHINE->SOFTWARE->ORACLE
    - setting ORACLE_HOME in control panel to sql developer path
    I installed
    sqldeveloper-3.1.07.42 incl. JDK for win32
    instantclient 11.2
    Any comments?
    thx -stefan

    Hello,  Please try the below steps. remove the cartridges.Unplug the power cord from back of the pritner.power Off the wireless router.Wait for 60 seconds.plug in the power cord to the printer only.install cartridges when prompted.If issue still exits, its time to replace the printer.Now power on the wireless router.If issue still exists, then check if there is a firmware update for the router. Also change the router settings Channel = 11,  mode= B/g.  Frequency = 2.4 GHzIf issue still persists, then its time to replace the printer. Please call HP Tech Support for further assistance.
    If you are in US , the toll free # is 1-800-474-6836 .
    If you are not in US , then log on to www.hp.com , at bottom-left corner there is a world map icon, click on it and then select the region you belong to, which would then provide support options for you for that region.

  • Error no gfx acceleration found when trying to play games on bootcamp windows

    Im trying to play games on a mid 2010 macbook pro i have used parrellels desktop to use windows so i can play better games but when i play a game of steam i get an error saying No GFX acceleration found. I have looked around online for a soloution and some one else on mac has had this problem but they were on a 2009 model and has a different graphics card and he says you need to update your drivers but i cant find an update for them anywhere can anyone help would be very happy if someone could give me a link to the drivers or tell me how to fix this
    thanks

    Okey, so when I was going too boot my computer it works good untill half the way thruh when boot campassistant is going too dowload the latest windows assistant it says "This computer can just do windows 7" then I press next after a few seconds it says "Can't dowload files because the server is busy" (this was just from my memory it may have been somthing else, but it is pretty much what it said). So how do I fix this, the easiest thing too just press a few buttons and choose a ISO image and the it can't even proseed to the pratipation....

  • Keep getting error message appication not found when trying to use Firefox, recently had lightning strike neighborhood box.

    also will not load automatically anymore since lost power few days ago.

    Same issue to with Windows XP SP3 x86 with Java Runtime Enviornment 1.5.0_15
    J2SE Enviornment 5.0 Update 15
    Java 6 Update 17

  • I keep getting error message " server stopped responding" when trying to connect to internet via wifi

    My iphone works fine using cellar network, but will not connect to internet via wifi. Ive reset network setting with no diffrence.
    Any ideas?

    And you can turn the WiFi button on and off?
    If yes, then you next need to try to Restore your iPhone from your backup.

  • I keep getting result code -43 not found when trying to load certain instruments. Any idea why

    I keep getting error code -43 not found when trying to load certain instruments. Any ideas?

    Errors 3000-3999 (3004, 3013, 3014, 3018, 3164, 3194, and so on): Error codes in the 3000 range generally mean that iTunes cannot contact the update server (gs.apple.com) on ports 80 or 443.
    Update to the latest version of iTunes.
    Verify the computer's date and time are accurate.
    Check that your security or firewall software is not interfering with ports 80 or 443, or with the server gs.apple.com.
    Follow Troubleshooting security software. Often, uninstalling third-party security software will resolve these errors.
    An entry in your hosts file may be redirecting requests to gs.apple.com (see "Unable to contact the iOS software update server gs.apple.com" above).
    Internet proxy settings can cause this issue. If you are using a proxy, try without using one.
    Test restoring while connected to a known-good network.

  • Installed itunes update 10.5.0.142 and now get the error message "Disc Burner or Software Not Found" when trying to burn playlist to disc.

    Installed itunes update 10.5.0.142 and now get the error message "Disc Burner or Software Not Found" when trying to burn playlist to disc.  Windows 7

    Hello queenabs,
    It sounds like you are trying to burn a playlist to a disc in iTunes, but you are getting the error, "disc burner or software not found."  I found a couple of resources that I think might help with an error like this.
    I recommend starting with the steps in this article:
    iTunes for Windows: Optical drive is no longer recognized, or "Disc burner or software not found" alert after install
    http://support.apple.com/kb/TS2308
    If you are still having trouble with burning a disc after following the steps in that article, I recommend following the steps in this article:
    iTunes for Windows: Additional troubleshooting tips for burning issues
    http://support.apple.com/kb/TS1374
    Thank you for using Apple Support Communities.
    Best,
    Sheila M.

  • When trying to connect airport express keep getting unexpected error please try again.  IVE TRIED A HUNDRED TIMES AND HAVE FOUND SUPPORT PAGES UNHELPFUL

    when trying to connect airport express keep getting unexpected error please try again.  IVE TRIED A HUNDRED TIMES AND HAVE FOUND SUPPORT PAGES UNHELPFUL

    Have you tried using a WEP password for your wireless network instead of a WPA one? That fixed it for me.

  • Keep getting Disc Burner or software not found when trying to burn a CD

    I am not able to burn a playlist to a CD and get an error at the top of Itunes window "Disc Burner or Software Not Found". I have been able to burn CDs in the past with this same computer but had some issues with songs in itunes. Support had me uninstall Itunes and reinstall. I have also uninstalled the device in the device manager and re-installed it. I really don't know what to try except to ask for help here. I would appreciate any direction I can get. I have a Dell desktop XPS running on Windows 8.

    Hi daurel, 
    Thanks for participating in the Apple Support Communities. 
    It sounds like you receive the error "Disc Burner or Software Not Found" when trying to burn CDs. You mention that you've already tried removing and reinstalling iTunes, and other drivers, and these are good steps. 
    If the situation continues, be sure to try the tips in this article:
    iTunes for Windows: Optical drive is no longer recognized, or "Disc burner or software not found" alert after install - Apple Support
    Sincerely,
    Jeremy 

  • Error -43 file not found when exporting from QT Pro 7.5

    I get the error -43 (a file could not be found) when trying to export into any format from within Quicktime Pro 7.5 (861) which i believe is the most current version. I also cannot perform a simple "save as" to save my video into another name, i dont get an error message for that one, but it just doesnt do anything. Im not sure if there is any point placing this on this forum, but maybe someone at Apple is interested in offering a little support...?

    OK so i found the solution myself - seems apple programmers have been not doing their jobs properly, to get this working the file name of the video that i want exported cannot be anything other than in 8.3 format (like old MS-DOS) but it's more than that, even if you do have the file in 8.3 format it still cant be in a directory that has a name longer than 8 characters, or which has spaces in it etc. so in my case i copied my video to c:\temp and renamed all of them to the old MS-DOS 8.3 format, now the export works... amazing I wonder how long i would have waited for apple support if i hadnt resolved this myself.

  • Error message when  trying to connect Classic 120GB to iTunes    An internal error occurred during: "FindSonarTrackJob". java.lang.NullPointerException

    When trying to connect to iTunes I get this message  
    An internal error occurred during: "FindSonarTrackJob".
    java.lang.NullPointerException

    I too am having this problem and have had, for about a week now.
    I've found that by logging off itunes (if I can), closing it down, and then restarting it, sometimes allows it to work for one transaction (say downloading an updated app). After that it's back to the same error.
    Really annoying.

  • HT1923 did anyone get the apple application support was not found when trying to instal?

    I am having trouble instaling itunes.  has anyone got the apple application support was not found when trying to instal itunes?  it looks like it is not installing all of files to my computer and it can not reach a certain folder

    With the Error 2, let's try a standalone Apple Application Support install. It still might not install, but fingers crossed any error messages will give us a better idea of the underlying cause of the issue.
    Download and save a copy of the iTunesSetup.exe (or iTunes64setup.exe) installer file to your hard drive:
    http://www.apple.com/itunes/download/
    Download and install the free trial version of WinRAR:
    http://www.rarlab.com/
    Right-click the iTunesSetup.exe (or iTunes64Setup.exe), and select "Extract to iTunesSetup" (or "Extract to iTunes64Setup"). WinRAR will expand the contents of the file into a folder called "iTunesSetup" (or "iTunes64Setup").
    Go into the folder and doubleclick the AppleApplicationSupport.msi to do a standalone AAS install.
    Does it install properly for you?
    If instead you get an error message during the install, let us know what it says. (Precise text, please.)

  • Oracle Fatal error when trying to connect through sqlplus

    Hi,
    I am getting the below error when trying to connect to instance through sqlplus
    Database version is :10.2.0.3
    Operating system= Solaris Operating System (SPARC 64-bit)
    OS version=5.10
    [lscbd07p2*BMC]-\ORACLE>sqlplus
    SQL*Plus: Release 10.1.0.4.0 - Production on Fri Nov 9 07:48:24 2007
    Copyright (c) 1982, 2005, Oracle. All rights reserved.
    Enter user-name: /as sysdba
    ld.so.1: oracle: fatal: relocation error: file /u01/app/oracle/product/db/10.1.0.4/lib/libjox10.so: symbol kststop_: referenced symbol not found
    ERROR:
    ORA-12547: TNS:lost contact
    Enter user-name:
    Could you all please give me suggestions in order to solve this problem.
    Thanks
    Mannu

    Have you recently patched/upgraded? This sounds like there might have been a problem relinking the executables / libraries, and/or a permissions problem. For example you may be referencing a 32 bit library with your 64 bit client.
    I believe I recently read a similar case - check Metalink for this symptom.
    HTH
    Regards Nigel

Maybe you are looking for

  • Problem with currency  field in smart form

    hi friends .. i had problem with currency field in smartform iam printing 5 currecny fields after the main window .But not getting printed on right way gets printed down from the given mesaurement and i get lot of gap betwen the each fields for ex. 3

  • How to set the header for second page

    Hello all, I'm trying to set different header for first page and page number should starts from second page. Below is the sample code to set the header for each and every page. DECLARE hApplication OLE2.OBJ_TYPE; hWindow OLE2.OBJ_TYPE; hPane OLE2.OBJ

  • AET : Check box in personalize setting is not showing

    Hi Guys I'm trying to enable the AET functionality using the option Personalize->Personalize Settings from the header area which is top right side, but there I'm not able to see the check box with option enable configuration mode. Is any notes is mis

  • Request fields in owa (PL/SQL)

    Hi! Probably this is a very trivial question, because I'm newbie in Web PL/SQL programming How can I retrieve form fields in PL/SQL code? (like the JSP directive request.get_value() or the ASP directive Request.Form() ?)

  • Need help finding the Motherboard parts number on Ideacentre B520

    Hi guys, I'm currently repairing an ideacentre B520 for a customer and need to have the MB parts # to have the parts ordered.  i've found a white sticker with somes number on it but I don't know which one is the MB parts number. Here the number: 27*9