Error:no Authentication servers responding

my clients keep on disconecting from the Aps in intervals of 10 minutes,the WLC displays the no Authentication servers responding error message when this happens..could this be the ACS SE that i am using.

Him
It could be the ACS or the network. Best way is to look at the failed attempts ans see if anything shows up on it.
Regards,
Vivek

Similar Messages

ERROR: Authentication no respond: no error

I configured an ASA as VPN using Windows IAS authentication. When using test aaa authentication command, I receive ERROR: Authentication no respond: no error. I can ping the IAS server? The configuration can be found this page:http://www.howtocisco.com/cisco/samples/iasexample.htm.
Any suggestions?

Hi,
Thank you for the reply. It didn't hit the IAS and no error in the Event Viewer. Then I found the problem was the IAS stops. After started it, my test received another error Invalid password. The Event shows ID 2 with authentication method is PAP. So I enabled the PAP (Unencrypted authentication) on the IAS. I can VPN in now. Is the the PAP (Unencrypted authentication)? Can I force the VPN use different authentication such as MS-CHAP v1 or v2?

ERROR: Ldap Authentication failed for dap during installation of iAS 6.0 SP3

I am attempting to install ias Enterprise Edition (6.0 SP3) on solaris 2.8 using typical in basesetup. I am trying to install new Directory server as I don't have an existing one.
During the installation I got the following error.
ERROR: Ldap Authentication failed for url ldap://hostname:389/o=NetScape Root user id admin (151: Unknown Error)
Fatal Slapd did not add Directory server information to config Server.
Warning slapd could'nt populate with ldif file Yes error code 151.
ERROR:Failure installing iPlanet Directory Server.
Do you want to continue: ( I entered yes )
Configuring Administration Server Segmentation fault core dumped.
Error: Failure installing Netscape Administration Server.
Do you want to continue:( I responded with yes).
And during the Extraction I got the following
ERROR:mple_bind: Can't connect to the LDAP server - No route to host
ERROR: Unable to connect to LDAP Directory Server
Hostname: hostname
Port: 389
User: cn=Directory Manager
Password: <password-for-cn=Directory Manager
Please make sure this Directory Server is currently running.
You might need to run 'stop-slapd' and then
'start-slapd' in the Directory Server home directory, in order to restart
LDAP. When finished, press ENTER to continue, or S to skip this step:
Start registering Bootstrap EJB...
javax.naming.NameNotFoundException
at java.lang.Throwable.fillInStackTrace(Native Method)
at java.lang.Throwable.fillInStackTrace(Compiled Code)
at java.lang.Throwable.<init>(Compiled Code)
at java.lang.Exception.<init>(Compiled > Code)
at javax.naming.NamingException.<init>(NamingException.java:114)
at javax.naming.NameNotFoundException.<init>(NameNotFoundException.java: 48)
at com.netscape.server.jndi.RootContext.resolveCtx(Unknown Source)
"ldaperror" 76 lines, 2944 characters
at com.netscape.server.jndi.RootContext.resolveCtx(Unknown Source)
at com.netscape.server.jndi.RootContext.bind(Unknown Source)
at com.netscape.server.jndi.RootContext.bind(Unknown Source)
at javax.naming.InitialContext.bind(InitialContext.java:371)
at com.netscape.server.deployment.EjbReg.deployToNaming(Unknown Source)
at com.netscape.server.deployment.EjbReg.registerEjbJar(Compiled Code)
at com.netscape.server.deployment.EjbReg.registerEjbJar(Compiled Code)
at com.netscape.server.deployment.EjbReg.run(Compiled Code)
at com.netscape.server.deployment.EjbReg.main(Unknown Source)
Start registering iAS 60 Fortune Application...
Start iPlanet Application Server
Start iPlanet Application Server
Start Web Server iPlanet-WebServer-Enterprise/6.0SP1 B08/20/200100:58
warning: daemon is running as super-user
[LS ls1] http://gedemo1.plateau.com, port 80 ready
to accept requests
startup: server started successfully.
After completion of installation, I tried to start the console. But I got the following error;
"Cant connect ot the admin server. The url is not correct or the server is not running.
Finally,when I started the admintool(iASTT),it shows the iAS1
was registered( marked with a red cross mark) and says "cant login. make sure the user
name & passwdord are correct" when i click on it.
Thanks in advance for any help
Madhavi

Hi,
Make sure that the directory server is installed first. If it is running
ok, then you can try adding an admin user, please check the following
technote.
http://knowledgebase.iplanet.com/ikb/kb/articles/4106.html
regards
Swami
madhavi korupolu wrote:
I am attempting to install ias Enterprise Edition (6.0 SP3) on
solaris 2.8 using typical in basesetup. I am trying to install new
Directory server as I don't have an existing one.
During the installation I got the following error.
ERROR: Ldap Authentication failed for url
ldap://hostname:389/o=NetScape Root user id admin (151: Unknown
Error)
Fatal Slapd did not add Directory server information to config
Server.
Warning slapd could'nt populate with ldif file Yes error code 151.
ERROR:Failure installing iPlanet Directory Server.
Do you want to continue: ( I entered yes )
Configuring Administration Server Segmentation fault core dumped.
Error: Failure installing Netscape Administration Server.
Do you want to continue:( I responded with yes).
And during the Extraction I got the following
ERROR:mple_bind: Can't connect to the LDAP server - No route to host
ERROR: Unable to connect to LDAP Directory Server
Hostname: hostname
Port: 389
User: cn=Directory Manager
Password: <password-for-cn=Directory Manager
Please make sure this Directory Server is currently running.
You might need to run 'stop-slapd' and then
'start-slapd' in the Directory Server home directory, in order to
restart
LDAP. When finished, press ENTER to continue, or S to skip this
step:
Start registering Bootstrap EJB...
javax.naming.NameNotFoundException
at java.lang.Throwable.fillInStackTrace(Native Method)
at java.lang.Throwable.fillInStackTrace(Compiled Code)
at java.lang.Throwable.<init>(Compiled Code)
at java.lang.Exception.<init>(Compiled > Code)
at javax.naming.NamingException.<init>(NamingException.java:114)
at
javax.naming.NameNotFoundException.<init>(NameNotFoundException.java:
48)
at com.netscape.server.jndi.RootContext.resolveCtx(Unknown Source)
"ldaperror" 76 lines, 2944 characters
at com.netscape.server.jndi.RootContext.resolveCtx(Unknown Source)
at com.netscape.server.jndi.RootContext.bind(Unknown Source)
at com.netscape.server.jndi.RootContext.bind(Unknown Source)
at javax.naming.InitialContext.bind(InitialContext.java:371)
at com.netscape.server.deployment.EjbReg.deployToNaming(Unknown
Source)
at com.netscape.server.deployment.EjbReg.registerEjbJar(Compiled
Code)
at com.netscape.server.deployment.EjbReg.registerEjbJar(Compiled
Code)
at com.netscape.server.deployment.EjbReg.run(Compiled Code)
at com.netscape.server.deployment.EjbReg.main(Unknown Source)
Start registering iAS 60 Fortune Application...
Start iPlanet Application Server
Start iPlanet Application Server
Start Web Server iPlanet-WebServer-Enterprise/6.0SP1 B08/20/200100:58
warning: daemon is running as super-user
[LS ls1] http://gedemo1.plateau.com, port 80 ready
to accept requests
startup: server started successfully.
After completion of installation, I tried to start the console. But I
got the following error;
"Cant connect ot the admin server. The url is not correct or the
server is not running.
Finally,when I started the admintool(iASTT),it shows the iAS1
was registered( marked with a red cross mark) and says "cant login.
make sure the user
name & passwdord are correct" when i click on it.
Thanks in advance for any help
Madhavi
Try our New Web Based Forum at http://softwareforum.sun.com
Includes Access to our Product Knowledge Base!

My iCal won't go online and returns the error message: The server responded with "500" to operation CalDAVAccountRefreshQueueableOperation.

My iCal won't go online and returns the error message: "The server responded with “500” to operation CalDAVAccountRefreshQueueableOperation."

OK Now I can answer my own question. The incomprehensible (inexcusably geeky) error message is actually Apple language for saying simply: "The iCloud servers are down again. Please wait until we've fixed them." I found this out by talking to Apple support. It took about 12 hours for the iCloud server synching calendars to come back online. When they did, my calendar reloaded, and everything was fine.

Error in replica servers

Hi
I am getting this error frequently in my replica server.I am using multimaster replication.All the replicas are read only replicas.I have 4 replica server and 2 master servers.
Please advice the solution for my problem.There is no information about this error code in sunone documentation so pls advice
[19/Sep/2005:13:50:39 +0000] - ERROR<4190> - Authentication - conn=-1 op=-1 msgI
d=-1 - Internal error Internal search base="CN=icpwps.ikea.com, OU=Operations,
O=IKEA IT AB, L=Elmhult, ST=Smaland, C=SE" scope=2 filter=objectclass=*, Result
: 32 (No such object)
Thanks & Regards
Raghavender Rao Kodumuri

You could re-initalize the replica from the admin console of the master, click the replication agreement, then click "Action/Initialize Remote Replica", there is no need to do anything at the replica assuming the replication has been properly setup.
BUT if you were to re-org the data at the master, and you have multiple masters, you should choose one good master and at this so called "good" master, you should temporarily break all the replication agreements with other master and replica, before you carry up the stop-slapd, db2ldif, ldif2db, start-slapd (DB reorg) I think. Anyone pls correct me if I am wrong.
After the master re-org, re-setup the Replication Agreements with other master and replica, and re-initialize the replica.
Gary

Error : Running Managed Servers in a cluster

Hi,
I tried creating a new domain from my local pc - by using the configuration wizard provided by weblogic.. the configuration used is like this -
Admin Server - adminServer - 1.1.1.19 - on port 7001
Managed servers - machines:ip's - port
1. mgndServer1 - 1.1.1.19 - 7011
2. mgndServer2 - 1.1.1.20 - 7011
mgndCluster defined as - mgndServer1:7011, mgndServer2:7011
node manager ; - 1.1.1.19 - 5555
In the last step i didnt check ( select box ) the WLI Start up , WLI Shutdown classes for the managed cluster , but Set the WLI Start up , shut down classes for admin server.
Started the admin server and from the admin console, state of the node manager was running , I tried starting the managed servers, but it failed with the below error - and managed servers never come into running state..
Log :
<Jan 29, 2010 10:36:26 AM CET> <Info> <NodeManager@*.*:5555> <Starting Server adminServer ::mgndServer1 ...>
<Jan 29, 2010 10:36:26 AM CET> <Info> <WebLogicServer> <BEA-000377> <Starting WebLogic Server with Java HotSpot(TM) Client VM Version 1.4.2_05-b04 from Sun Microsystems Inc.>
<Jan 29, 2010 10:36:26 AM CET> <Info> <Management> <BEA-141140> <The managed server is going to contact the admin server at http://1.1.1.19:7001 to check if there exists a running admin server at this URL.>
<Jan 29, 2010 10:36:26 AM CET> <Info> <Configuration Management> <BEA-150017> <This server is being started as a dependent managed server.>
<Jan 29, 2010 10:36:26 AM CET> <Info> <Management> <BEA-141107> <Version: WebLogic Server 8.1 SP4 Mon Nov 29 16:21:29 PST 2004 471647
WebLogic XMLX Module 8.1 SP4 Mon Nov 29 16:21:29 PST 2004 471647 >
<Jan 29, 2010 10:36:26 AM CET> <Info> <Configuration Management> <BEA-150015> <Connecting to the administration server http://1.1.1.19:7001 to retrieve the initial configuration.>
<Jan 29, 2010 10:36:27 AM CET> <Info> <NodeManager@*.*:5555> <Server myDomain::mgndServer1 started, process id = 6,888>
<Jan 29, 2010 10:36:28 AM CET> <Notice> <Log Management> <BEA-170019> <The server log file C:\bea\weblogic81\common\nodemanager\mgndServer2\mgndServer2.log is opened. All server side log events will be written to this file.>
<Jan 29, 2010 10:36:29 AM CET> <Notice> <Security> <BEA-090082> <Security initializing using security realm myrealm.>
<Jan 29, 2010 10:36:29 AM CET> <Notice> <Security> <BEA-090170> <Loading the private key stored under the alias DemoIdentity from the jks keystore file C:\bea\weblogic81\server\lib\DemoIdentity.jks.>
<Jan 29, 2010 10:36:29 AM CET> <Notice> <Security> <BEA-090171> <Loading the identity certificate stored under the alias DemoIdentity from the jks keystore file C:\bea\weblogic81\server\lib\DemoIdentity.jks.>
<Jan 29, 2010 10:36:29 AM CET> <Notice> <Security> <BEA-090169> <Loading trusted certificates from the jks keystore file C:\bea\weblogic81\server\lib\DemoTrust.jks.>
<Jan 29, 2010 10:36:29 AM CET> <Notice> <Security> <BEA-090169> <Loading trusted certificates from the jks keystore file C:\bea\jdk142_05\jre\lib\security\cacerts.>
<Jan 29, 2010 10:36:30 AM CET> <Notice> <WebLogicServer> <BEA-000328> <Starting WebLogic Managed Server "mgndServer1" for domain "myDomain">
<Jan 29, 2010 10:36:57 AM CET> <Notice> <Cluster> <BEA-000138> <Listening for announcements from cluster mgndCluster on 237.0.0.13:7011.>
<Jan 29, 2010 10:36:57 AM CET> <Notice> <Cluster> <BEA-000133> <Waiting to synchronize with other running members of mgndCluster.>
<Jan 29, 2010 10:37:27 AM CET> <Notice> <JTA> <BEA-110025> <Creating new transaction log file [.\mgndServer1\./mgndServer1.0000.tlog].>
<Jan 29, 2010 10:37:27 AM CET> <Notice> <JTA> <BEA-110025> <Creating new transaction log file [.\mgndServer1\./mgndServer1.heur.0000.tlog].>
<Jan 29, 2010 10:37:35 AM CET> <Error> <Deployer> <BEA-149205> <Failed to initialize the application WLI Worklist due to error weblogic.management.ManagementException: [Deployer:149233]An unexpected error was encountered during the deployment process. - with nested exception:
[java.lang.NoClassDefFoundError: com/bea/wlw/runtime/core/bean/SLSBContainerBean].
java.lang.NoClassDefFoundError: com/bea/wlw/runtime/core/bean/SLSBContainerBean
at java.lang.ClassLoader.defineClass0(Native Method)
at java.lang.ClassLoader.defineClass(ClassLoader.java:539)
at java.security.SecureClassLoader.defineClass(SecureClassLoader.java:123)
at weblogic.utils.classloaders.GenericClassLoader.findLocalClass(GenericClassLoader.java:480)
at weblogic.utils.classloaders.GenericClassLoader.findClass(GenericClassLoader.java:182)
at java.lang.ClassLoader.loadClass(ClassLoader.java:289)
at java.lang.ClassLoader.loadClass(ClassLoader.java:235)
at weblogic.utils.classloaders.GenericClassLoader.loadClass(GenericClassLoader.java:224)
at weblogic.ejb20.deployer.EJBModule.setupEJBToImplClassDependencies(EJBModule.java:1030)
at weblogic.ejb20.deployer.EJBModule.prepare(EJBModule.java:481)
at weblogic.j2ee.J2EEApplicationContainer.prepareModule(J2EEApplicationContainer.java:3142)
at weblogic.j2ee.J2EEApplicationContainer.prepareModules(J2EEApplicationContainer.java:1583)
at weblogic.j2ee.J2EEApplicationContainer.prepare(J2EEApplicationContainer.java:1227)
at weblogic.j2ee.J2EEApplicationContainer.prepare(J2EEApplicationContainer.java:1070)
at weblogic.j2ee.J2EEApplicationContainer.prepare(J2EEApplicationContainer.java:823)
at weblogic.management.deploy.slave.SlaveDeployer$Application.prepare(SlaveDeployer.java:3026)
at weblogic.management.deploy.slave.SlaveDeployer.prepareAllApplications(SlaveDeployer.java:967)
at weblogic.management.deploy.slave.SlaveDeployer.resume(SlaveDeployer.java:349)
at weblogic.management.deploy.DeploymentManagerServerLifeCycleImpl.resume(DeploymentManagerServerLifeCycleImpl.java:229)
at weblogic.t3.srvr.SubsystemManager.resume(SubsystemManager.java:131)
at weblogic.t3.srvr.T3Srvr.resume(T3Srvr.java:966)
at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:361)
at weblogic.Server.main(Server.java:32)
--------------- nested within: ------------------
weblogic.management.ManagementException: [Deployer:149233]An unexpected error was encountered during the deployment process. - with nested exception:
[java.lang.NoClassDefFoundError: com/bea/wlw/runtime/core/bean/SLSBContainerBean]
at weblogic.management.deploy.slave.SlaveDeployer.convertThrowable(SlaveDeployer.java:1017)
at weblogic.management.deploy.slave.SlaveDeployer.access$500(SlaveDeployer.java:124)
at weblogic.management.deploy.slave.SlaveDeployer$Application.prepare(SlaveDeployer.java:3034)
at weblogic.management.deploy.slave.SlaveDeployer.prepareAllApplications(SlaveDeployer.java:967)
at weblogic.management.deploy.slave.SlaveDeployer.resume(SlaveDeployer.java:349)
at weblogic.management.deploy.DeploymentManagerServerLifeCycleImpl.resume(DeploymentManagerServerLifeCycleImpl.java:229)
at weblogic.t3.srvr.SubsystemManager.resume(SubsystemManager.java:131)
at weblogic.t3.srvr.T3Srvr.resume(T3Srvr.java:966)
at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:361)
at weblogic.Server.main(Server.java:32)
>
<Jan 29, 2010 10:37:38 AM CET> <Error> <Deployer> <BEA-149205> <Failed to initialize the application WLI System EJBs due to error weblogic.management.ApplicationException: prepare failed for WLI Process Tracking
Module Name: WLI Process Tracking, Error: Exception preparing module: EJBModule(WLI Process Tracking,status=NEW)
Unable to deploy EJB: .\mgndServer2\stage\WLI System EJBs\tracking from tracking:
weblogic.ejb20.deployer.DeploymentDescriptorException: Unable to load a class specified in your ejb-jar.xml: com.bea.wli.management.tracking.ProcessTrackingBean
at weblogic.ejb20.deployer.MBeanDeploymentInfoImpl.initializeBeanInfos(MBeanDeploymentInfoImpl.java:550)
at weblogic.ejb20.deployer.MBeanDeploymentInfoImpl.<init>(MBeanDeploymentInfoImpl.java:232)
at weblogic.ejb20.deployer.EJBDeployer.prepare(EJBDeployer.java:1324)
at weblogic.ejb20.deployer.EJBModule.prepare(EJBModule.java:498)
at weblogic.j2ee.J2EEApplicationContainer.prepareModule(J2EEApplicationContainer.java:3142)
at weblogic.j2ee.J2EEApplicationContainer.prepareModules(J2EEApplicationContainer.java:1583)
at weblogic.j2ee.J2EEApplicationContainer.prepare(J2EEApplicationContainer.java:1227)
at weblogic.j2ee.J2EEApplicationContainer.prepare(J2EEApplicationContainer.java:1070)
at weblogic.j2ee.J2EEApplicationContainer.prepare(J2EEApplicationContainer.java:823)
at weblogic.management.deploy.slave.SlaveDeployer$Application.prepare(SlaveDeployer.java:3026)
at weblogic.management.deploy.slave.SlaveDeployer.prepareAllApplications(SlaveDeployer.java:967)
at weblogic.management.deploy.slave.SlaveDeployer.resume(SlaveDeployer.java:349)
at weblogic.management.deploy.DeploymentManagerServerLifeCycleImpl.resume(DeploymentManagerServerLifeCycleImpl.java:229)
at weblogic.t3.srvr.SubsystemManager.resume(SubsystemManager.java:131)
at weblogic.t3.srvr.T3Srvr.resume(T3Srvr.java:966)
at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:361)
at weblogic.Server.main(Server.java:32)
weblogic.management.ApplicationException: prepare failed for WLI Process Tracking
Module Name: WLI Process Tracking, Error: Exception preparing module: EJBModule(WLI Process Tracking,status=NEW)
Unable to deploy EJB: .\mgndServer2\stage\WLI System EJBs\tracking from tracking:
weblogic.ejb20.deployer.DeploymentDescriptorException: Unable to load a class specified in your ejb-jar.xml: com.bea.wli.management.tracking.ProcessTrackingBean
at weblogic.ejb20.deployer.MBeanDeploymentInfoImpl.initializeBeanInfos(MBeanDeploymentInfoImpl.java:550)
at weblogic.ejb20.deployer.MBeanDeploymentInfoImpl.<init>(MBeanDeploymentInfoImpl.java:232)
at weblogic.ejb20.deployer.EJBDeployer.prepare(EJBDeployer.java:1324)
at weblogic.ejb20.deployer.EJBModule.prepare(EJBModule.java:498)
at weblogic.j2ee.J2EEApplicationContainer.prepareModule(J2EEApplicationContainer.java:3142)
at weblogic.j2ee.J2EEApplicationContainer.prepareModules(J2EEApplicationContainer.java:1583)
at weblogic.j2ee.J2EEApplicationContainer.prepare(J2EEApplicationContainer.java:1227)
at weblogic.j2ee.J2EEApplicationContainer.prepare(J2EEApplicationContainer.java:1070)
at weblogic.j2ee.J2EEApplicationContainer.prepare(J2EEApplicationContainer.java:823)
at weblogic.management.deploy.slave.SlaveDeployer$Application.prepare(SlaveDeployer.java:3026)
at weblogic.management.deploy.slave.SlaveDeployer.prepareAllApplications(SlaveDeployer.java:967)
at weblogic.management.deploy.slave.SlaveDeployer.resume(SlaveDeployer.java:349)
at weblogic.management.deploy.DeploymentManagerServerLifeCycleImpl.resume(DeploymentManagerServerLifeCycleImpl.java:229)
at weblogic.t3.srvr.SubsystemManager.resume(SubsystemManager.java:131)
at weblogic.t3.srvr.T3Srvr.resume(T3Srvr.java:966)
at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:361)
at weblogic.Server.main(Server.java:32)
at weblogic.j2ee.J2EEApplicationContainer.prepareModules(J2EEApplicationContainer.java:1604)
at weblogic.j2ee.J2EEApplicationContainer.prepare(J2EEApplicationContainer.java:1227)
at weblogic.j2ee.J2EEApplicationContainer.prepare(J2EEApplicationContainer.java:1070)
at weblogic.j2ee.J2EEApplicationContainer.prepare(J2EEApplicationContainer.java:823)
at weblogic.management.deploy.slave.SlaveDeployer$Application.prepare(SlaveDeployer.java:3026)
at weblogic.management.deploy.slave.SlaveDeployer.prepareAllApplications(SlaveDeployer.java:967)
at weblogic.management.deploy.slave.SlaveDeployer.resume(SlaveDeployer.java:349)
at weblogic.management.deploy.DeploymentManagerServerLifeCycleImpl.resume(DeploymentManagerServerLifeCycleImpl.java:229)
at weblogic.t3.srvr.SubsystemManager.resume(SubsystemManager.java:131)
at weblogic.t3.srvr.T3Srvr.resume(T3Srvr.java:966)
at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:361)
at weblogic.Server.main(Server.java:32)
>
Please help me in understand what went wrong here ? can anyone quickly guide me ..
thanks
patrick

Hi,
OPTION-A)
If you are able to start the Managed Server using ...the Start Scripts then it means that the Missing class gets included in the Server Classpath ....when we use StartScripts to Start the Server.
If above one works fine...then Just try the following..
Step1). Open the "nodemanager.properties" file and then "startScriptEnabled=true" and "startScriptName=startWebLogic.cmd" ....provide these two entries there....remember if you are using any custom scripts to start your managed server ...then give that scriptname in "startScriptName" parameter..
Step2). restart the Node Manager and then try to start the Managed Server from Admin Console.
for more informations Please refer to "nodemanager.properties" details:
http://download-llnw.oracle.com/docs/cd/E15051_01/wls/docs103/nodemgr/java_nodemgr.html#wp1068415
OPTION-B)
Start the ManagedServer using the StartScripts and then open the server OUT file....
Find the value of CLASSPATH in that OUT File ...copy the CLASSPATH Value and then Login to Admin Console....
Servers--->Click on ServerName (Example MS1)---> configuration Page ---> ServerStart (TAB)
In this page Paste the CLASSPATH Value which u have copied....in the CLASSPATH Test Field...
Now restart your Server using AdminConsole.
Thanks
Jay SenSharma
Edited by: Jay SenSharma on Jan 30, 2010 10:55 PM

ACC Setup Error - Remote Server not Responding in the Proper Manner - Windows 7 Pro

Hello -
I was able to install the CC upgrades to all my software on my laptop without issue. Whenever I try to upgrade them on my desktop I recieve the attached error. I am running Windows 7 Professional. My guess this is being caused my my company's firewall however my IT director claims he set me up to bypass the firewall when trying to install this.
Thank you for your help.

Hi Mike603,
Please refer to the following help document on error " Remote Server not responding".
http://helpx.adobe.com/creative-suite/kb/remote-server-responding-installing-aam.html
Hope this helps.
Please let me know in case of any problem.
Regards,
Sumit Singh

Getting %Error in authentication when using enable password via ACS 5.5

Hey, I've been on a LAN that's been using ACS 4.1 and its been working fine. Ive recently installed ACS 5.5 on a VM and Im attempting to get it to work. I've changed the Tacacs IP to the new server and the secret key on this particular switch and Ive configured it in the Network devices in ACS. When I log into the switch via SSH, it lets me authenticate to my username/password BUT when I go to enable it asks for a password. I enter the password I configured in ACS and I get %Error in authentication. I've also tried the local enable, same thing. What else is weird is that if I enter no password, it prompts me to change my password but if I try that I get the same error (%Error in authentication). The ACS log just simply says entered wrong password, even though I checked it multiple times and even tried a new account. I'm no master at AAA but from what I can tell it should work. Attaching my configuration....
Any ideas would be great

Can you share "show run | in aaa" from the switch?
You should have the below listed commands on the switch:
aaa authentication login default group CLI local
aaa authorization exec default group CLI local
On the ACS you should push priv-lvl=15
You may go through the below listed document for better understanding:
http://www.cisco.com/c/en/us/support/docs/security/secure-access-control-system/113590-acs5-tacacs-config.html
Regards,
Jatin Katyal
*Do rate helpful posts*

Acrobat Pro is now constantly giving me the error message (program not responding) when I try and perform any kind of action.

Acrobat Pro is now constantly giving me the error message (program not responding) when I try and perform any kind of action.

Hi cruzsanta03,
Can you please let us know the following:
- Operating System;
- Complete version of Acrobat installed;
- Experiencing this issue with a particular file or all PDF files;
- Experiencing this issue while performing a particular task or with any task;
- Files are saved on the local machine or on a share drive;
- Launch Acrobat in Safe Mode and then check the issue. Hold 'Shift' key and launch Acrobat, and then check the issue.

WLC 4400 and multiple authentication servers e.g. RADIUS, ACS

WLC 4400 and multiple authentication servers e.g. RADIUS, ACS
Can the WCL 4400 be set up to use multiple RADIUS servers? The user accounts for accessing wireless would use a RADIUS server. The administrative accounts for the WLC would reside on an ACS server.

Yes, that is correct. You can set acs to use both radius and tacacs.
For this you need to add WLC twice in acs-->network configuration. But you need to keep host name different.
eg 1) Host name WLC --->IP x.x.x.x -->Auth using -->radius
2) Host name WLC1--->IP x.x.x.x --->Auth using -->Tacacs.
You need to set up tacacs commands on WLC along with radius commands.
Regards,
~JG
Please rate helpful posts

When I try to send an email message I get smtp error(535) Authentication failed

I use the email from Stevens Inst. of Tech. I can receive messages,but when I try to send one I get the message: SMTP Error (535) Authentication failed. When I try the same thing in Chrome, I have no problem.

Contact your e-mail provider.
Many site issues can be caused by corrupt cookies or cache.
* Clear the Cache and
* Remove Cookies '''''Warning ! ! '' This will log you out of sites you're logged in to.'''
Type '''about:preferences'''<Enter> in the address bar.
* '''Cookies;''' Select '''Privacy.''' Under '''History,''' select Firefox will '''Use Custom Settings.''' Press the button on the right side called '''Show Cookies.''' Use the search bar to look for the site. Note; There may be more than one entry. Remove '''All''' of them.
* '''Cache;''' Select '''Advanced > Network.''' Across from '''Cached Web Content,''' Press '''Clear Now.'''
If there is still a problem,
'''[https://support.mozilla.org/en-US/kb/troubleshoot-firefox-issues-using-safe-mode Start Firefox in Safe Mode]''' {web link}
While you are in safe mode;
Type '''about:preferences#advanced'''<Enter> in the address bar.
Under '''Advanced,''' Select '''General.'''
Look for and turn off '''Use Hardware Acceleration'''.
Poke around safe web sites. Are there any problems?
Then restart.
I looked up the error on a search engine.
http://www.bing.com/search?q=SMTP%20Error%20%28535%29
Check that you are using the correct user / password.

UTL_SMTP and SMTP-Error: 530 Authentication required

Hi,
I wanna use the utl_smtp-package and while testing the example of the 9i-documentation, I got the error:
ORA-29279: Permanent SMTP-Error: 530 Authentication required
The only help I found was the sentence in the docu:
530: Must issue a STARTTLS command first. Encryption required for requested authentication mechanism.
What does it mean and how can I avoid this error?
It's true, that my smtp-account of my provider needs an authentication (pop3 before smtp!)
Thanx a lot!
Wolfgang

Hey, Community Girl! I just spent 2 days ripping my hair out over this same issue... The answer was maddeningly simple/stupid. In Outlook... they ASK for your "user name" and "Password" (on the More Settings Tab). What they
actually WANT is your "email address" NOT your "user name", followed by your password. This is easy.. I hope it works the same for you.
In Outlook, go to Tools, Email Accounts, View or Change, click Next. Highlight account information and click change. In the lower right of the page... Click More Settings.
Click the Outgoing Server Tab.
Check the My outgoing server SMTP requires authorization.
Check Log on Using:
User Name: Do NOT type your user name here... type your email address!
Password: Type in your password.
Check the Remember password box. OK
That one small change FIXED 2 days of hair pulling on my part... I hope that does it for you too.
Let me know... I'd be interested if you fixed it. Wish they had actually asked for what they wanted... User Name or Email Address ARE two different things! Good luck!
South Texan, you're a genius! This 530 Authentication error has plagued me for 3 years now; when I call my internet service, they say it's a router firewall issue; when I call them, they say it's not their issue. Changing the User Name field to
my email address instead of my user account name worked!!!!! Thank you!!

HT1178 I'm setting up airport for first time. I'm getting error no DNS servers help

I'm setting up airport for first time. Getting error no DNS servers. What is DNS server and how do I fix this?

DNS server is that translation from a website address in words meaningful to us.. eg www.google.com to an actual number that computers can use. Without DNS the internet may work but you would have to know the ipv4 address of every site you want to visit.
Whenever you don't know the meaning of a term just type wiki plus the term in google search.
http://en.wikipedia.org/wiki/Domain_Name_System
We cannot really help fix the problem without knowing a good deal more info.
So
What modem do you have.. make and model may be a help?
Who is your ISP.. may be helpful??
Is the modem also a router?
How is the TC connected to the modem?
How is the computer connected to the TC?
A primary example of where you get this problem is a pure cable modem.. ie has no router in it.
When you replace an existing computer or router that is plugged into it, with the TC, requires that you power cycle the modem. In some cases the off time is 5min.. for a lot of services, it needs to be off 20min.. and for some even longer.. maybe an hour or overnight.
But it is not worth getting into specifics without knowing the rest of the system.

Aironet 1240AG error - "Previous authentication no longer valid" Help!

Greetings!
I am an IT professional that is installing my first extended range wireless AP in my companies warehouse. I am very excited!
Now I have set up many a linksys and repeater wireless networks, so when I was looking into the Aironet 1240AG I thought ?No Problem!?
And at first, it is not!
I have the AP and antenna set up here in my office before I take it out and mount it in the warehouse. And I can get connected to it, no security for now, no filters, I just want to connect and make it work.
I stay connected for maybe 3 minutes, I can get to the internet, I can ping all my servers. Full connectivity. But then for no reason the connection fails and I cannot reconnect.
The error I get in the log is
Interface Dot11Radio0, Deauthenticating Station 0006.2510.bbe3 Reason: Previous authentication no longer valid
So strange! So I have reset the AP to factory defaults and then set the SSID, and I can connect, again for a second, then nothing.
I have tried with multiple wireless cards, even laptops. Thinking maybe the problem was on the computer side.
But now I believe I must have some setting wrong.
Could someone please shed some light on this situation for me! I searched the forums but could not find this error message in this context.
Thanks!
Nate York

Interesting...I am experiencing the same problem, but when adding another laptop to the existing 5 Aironet 1100's. The existing laptops work fine, but when trying to add another node, I see the problem. I get the following error message in the error log as well as the activity screen;
Interface Dot11Radio0, Deauthenticating Station 0002.2d34.a0fe Reason:
Previous authentication no longer valid
Unit - 6 units
Cisco Aironet 1100 version 12.3.(07)JA
The error takes place with no other units online, or when other units are in use. Also the laptop in question "shows" connected to the AP (yes I have tried other APs all with negative results). The settings on the laptops are all the same, so i am at a loss.
Any suggestions greatly appreciated,
Ralph

Unknown Error: PDF_TEST_00 not returned Responds

Hi Gurus,
I am trying to execute some AIF using the T Code: FMBB, but just before calling the form itself, my testing program got stuck and does not longer respond. No messages, no outputs, nothing after that.
Have been to all of the step in this link: (Adobe Document Services http://help.sap.com/erp2005_ehp_03/helpdata/EN/37/504b8cbc2848a494facfdc09a359b1/frameset.htm)
-Others steps I have done so far: Checking the IIOP Service and the Startup Properties
- I execute the Report FP_TEST_00.
 Here is when it all comes, run the report, choosing a printer up to the
 Parameters for printing AIF(Device Type: Post2) then I got a never-ending wait
 cursor so the system is not longer responding. No Errors, no output, nothing at all.
 I come to check the other test to resolve the error, according to the guide:
 1. Checking the ABAP Connection:
 execute the report FP_PDF_TEST_00
 so good!, the report shows the version number of the Adobe document services as the guide says.
 2. Checking the User and Password:
 Server : dr6server.
 J2EE Instance : 03.
 Port : 50300.
 SID : DRA
 URL = http://dr6server:50300/AdobeDocumentServices/Config
 Enter the URL in Web browser and Choose rpdata(test.)., enter the ADSUser and
 password and the system displays the version number of the Adobe document
 services in the response area, test successful!
 3. Checking the Destination Service and the ICF Service
 execute the report FP_CHECK_DESTINATION_SERVICE.
 - Here the problem comes again, I just run the report above then got no respond at all. I could
 Identify the line code where it does not continue:
 l_soapresponse = adsobject->run( ).
- Apparently there are problems with the configuration of ADS, although already set ADS_AGENT with his role SAP_BC_FP_ICF, ADS_User with his role ADS_CALLERS, FP_ICF_DATA_ <SID> already been created in J2EE , install and configure the credentials of ADOVE successfully, the HTTP connection(RFC Destination 'ADS') was created successfully , and check the ICF in browser and the visual j2ee administrator and a test was successful only lacking in AS ABAP that gives me the error.
- Configuration of the Web Service for Basic Authentication have been use as step by step guide
 configuration But the problem with the reports:
 FP_TEST_00,FP_CHECK_DESTINATION_SERVICE. remains.
Can anyone please explain me where and how should I set the ADS to make this test successful.
Thanks in advance
regards

Hello Maarten ,
first of all thank you for your quick reaction.
I run the program both ways, but there is no single answer falls into a cycle as infinity,
The service was created in the visual Administrator previously said that according to what the guide configuration, in the visual amdministrador -> Services -> Destinations. I introduced FP_ICF_DATA_DRA (ID system is DRA).
assign a name = "DR6SERVER" and port = "8003" which I found in the T-code SICF, authentication Basic client = "300" user = ADS_AGENT and passw (previously established with AS Abap Role = "SAP_BC_FP_ICF" probe save and test and the response was "GET HTTP response code 200" Test success.
but still not responding the report.
even probe "http://DR6SERVER:8003/sap/bc/fp/form/layout/fp_test_00.xdp"
both in the Administrator visual-> Services -> Destinations and in the browser and generates response.
Do you have another ideas solving my problem?
Thanks in advance
regards
Miguel

Error:no Authentication servers responding

Similar Messages

Maybe you are looking for