Error "No drive attached to fastrack controller, the bios is not installed"
Having recently purchased a K7N2 Delta mainboard I now get the above error displayed during bootup. Shortly after the message has been displayed the windows boot process hangs.
What have I done wrong or what havn't I done right?
My system spec is:
Athlon 2500xp
80 gig Maxtor HDD
1024 DDR ram (single stick)
XP Professional
N-vidia graphics 440
regards
Technomarv
Hi,
Technomarv:
Listen to what others are saying! "The BIOS not installed" message is NOT a problem My machine says this EVERY time I boot Up! There is obviously something else wrong.
You say:
Quote
The problem does not appear to be with the boot sector as when I put the hard drive into another machine it boots perfectly. Once back in MSI machine the boot process hangs again. I therefore find it difficult just to ignore the PC when it tells me "The bios is not installed".
Am I to understand from this that your trying to boot the same hard drive using two different motherboards? If so - I'm not surprised it doesn't boot! It is advisable to do a full and new install of your OS - to your HD - when installing a new board.
You can't just move a hard drive from one machine to another and hope a boot will be successful (this can only be done when the motherboard and or add-ons are the same or very similar).
Axel
Similar Messages
-
I am getting an error message with my snap scan ix500 that says the Evernote is not installed properly when I try to transfer it. I have uninstalled/reinstalled evernote and the scan snap softward but it still doesn't work. Anyone know where evernote stores their files on a Mac? Or had this problem.
Are there any dialog boxes popping up behind your Yahoo screen?
I have intermittent problems attaching files in Yahoo mail and this is usually the reason. I'm also using an iMac (10.7.3) and this is likely the problem.
It is generally a Yahoo issue rather than a Mac problem. -
NFS write error: on host (10.10.10.10 (the disk array): Not Owner).
A disk array is attached to the Sun OS 5.8 server through NFS and is used for the storage of the iPlanet Message server's message store. There are warnings for this NFS volume: NFS write error: on host (10.10.10.10 (the disk array): Not Owner). What does this mean?
During the restart of the solaris server, this warning messaging repeated endlessly on the screen with a white backgroud.
I had to use Stop-A to stop it, and then, panic and dump occured.
During the startup, a message was "consistent dma sync timeout." What does this mean?
After the server restarted, the NFS warnings are still there.
The server is Solaris 8 on SunFire 480.
What could the problems be? How to solve them?Thanks.
Let me clarify the situation here:
Only the mailboxes are on the NFS volume and shared by the two mail servers. -
msg-instance/store/mboxlist and msg-instance/store/user are located locally. ONLY msg-instance/store/partition/primary is on the NFS volume and shared between the two mail servers.
So, would this still be a problem?
And, yes, the mailsvr user id exists on the IBM NAS which provides disk arrays for this NFS volume. Do I need grant particular rights to this user on NAS? Do I need to do something on the NFS server which, I think it is the Sun server?
Thanks again. -
i am trying to install msnbc app from the app store and keep getting an error message. The app will not install. What can i do?
This is asked and answered many times each day. The forum search bar is on the right side of this page.
Disable your firewall/security software and try again. -
HI,
I get this error "Error occurred in deployment step 'Retract Solution': The solution does not have a WSP file associated with it. " when deploying my project from visual studio 2010 to
SharePoint 2010 site. I tried restarting IIS, but it didn't help. This application used to work fine until the server crashed during the deployment process. All the other applications on the same server works fine also. Any ideas how to fix this issue?
Thanks in advance,
AMHi
AM ,
Thank you for your posting!
According to your error message, it says your solution does not have a WSP file associated with it. Take a look at the file system. After you Right Click -> Deploy Solution on the VS Solution, there
should be a .wsp file at <Solution Directory>\bin\<debug|release>.
Also the error can be occurring when the developer try to deploy solutions over pre-existing solutions with material changed in the solution. Go to your Central Administration Site and then
Operations and then Solution Management. Make sure that there not already a solution with the same name deployed or installed there. If there is, remove it and try deploying again.
And you could look in logs and find if there is a below error in ULS log (C:\Program Files\Common Files\Microsoft Shared\Web Server Extensions\14\LOGS).
Thank you for your understanding and support.
Best Regards,
Eric
Eric Tao
TechNet Community Support -
I just purchased Adobe Photoshop Elements 13 but my PC is not recognizing my CDRom and I cannot download the program. I tried copying the files on the program disc to my hard drive but get a message the installer will not work. I have the redemption code and serial numbers. Can I download the program online somewhere? If I download a trial version for instance will it allow me to enter my serial number and use it for the full program?
Downloads available:
Suites and Programs: CC 2014 | CC | CS6 | CS5.5 | CS5 | CS4 | CS3
Acrobat: XI, X | 9,8 | 9 standard
Premiere Elements: 13 | 12 | 11, 10 | 9, 8, 7 win | 8 mac | 7 mac
Photoshop Elements: 13 |12 | 11, 10 | 9,8,7 win | 8 mac | 7 mac
Lightroom: 5.6| 5 | 4 | 3
Captivate: 8 | 7 | 6 | 5
Contribute: CS5 | CS4, CS3
Download and installation help for Adobe links
Download and installation help for Prodesigntools links are listed on most linked pages. They are critical; especially steps 1, 2 and 3. If you click a link that does not have those steps listed, open a second window using the Lightroom 3 link to see those 'Important Instructions'. -
I downloaded the latest iTunes version and now get the following error message: "This copy of iTunes is corrupted or is not installed correctly. Please re-install iTunes." Can anyone provide suggestions on what I should do next?
Let's try a repair install of iTunes first.
Restart the PC. If you're using Vista or 7, now head into your Uninstall a program control panel, select "iTunes" and then click "Repair". If you're using XP, head into your Add or Remove Programs control panel, select "iTunes", click "Change" and then click "Repair".
Can you launch your iTunes now? -
I tried to install in my Sony Vaio Laptop - Model Name SVF15218SGW Serial No 54****************954. After installation of itunes, when i am trying to connect error message is showing as follows -
"This iphone cannot be used because the required software not installed. Run the itunes installer to remove the itunes, then install the 64bit version of itunes".
i already installed 64bit version. but not connecting my iphone with itunes
PLEASE HELP.!!!!
<Personal Information Edited by Host>Hello Negaz
When you uninstalled iTunes, did you uninstall it by using the article below or just uninstalled iTunes? The best practice is to remove not only iTunes, but also other associating software in the order that the first article give. If that does not work, then check out the second article for more troubleshooting options for connecting your iPhone to your computer.
Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8
http://support.apple.com/kb/ht1923
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/ts1538
Regards,
-Norm G. -
I am trying to download the update IOS 5 version for mi ipad 2 and at the end when it finishes downloading it shows an error "connection has been interrupted and that the task could not be completed", my internet service is fine, what can it be?
The 2nd generation can not be upgraded beyond 4.2.1.
-
When trying to load music from ITunes to my ipod I receive the error "The software required for the ipod is not installed correctly. Please reinstall itunes to install the required sotware"
What should I do to correct the error?For general advice see Troubleshooting issues with iTunes for Windows updates.
The steps in the second box are a guide to removing everything related to iTunes and then rebuilding it which is often a good starting point unless the symptoms indicate a more specific approach. Review the other boxes and the list of support documents further down the page in case one of them applies. The notes below the box include tips on removing troublesome components.
The further information area has direct links to the current and recent builds in case you have problems downloading, need to revert to an older version or want to try the iTunes for Windows (64-bit - for older video cards) release as a workaround for installation or performance issues, or compatibility with QuickTime or third party software.
Your library should be unaffected by these steps but there also links to backup and recovery advice should it be needed.
tt2 -
The application was not installed unknown error: 0xE8000050
The application was not installed unknown error: 0xE8000050.
How to fix please???If it helps, the redirect page when I clicked on more information was:
http://support.apple.com/kb/TS1702
I tried all the following, rebooted my ipod still didnt work.
I would like to know how to completely remove all traces of the application, so I can reinstall it again. Thanks. -
i got my new iphone 4s , can not download the OS 5 it says error 9006 on my windows 7. also the phone does not show the capacity and serial number details on the itunes summery ?? please help
Hi Kevin,
The iPhone 4S comes automatically loaded with iOS 5, and any updates after iOS 5.0 can be completed directly from on the phone in Settings > General > Software Update. If you are having trouble using iTunes to update software, I suggest you reset iTunes so that you can pair your phone to the computer again, because if you can't see the serial number and capacity, that generally means your phone isn't paired. For any problems this doesn't fix, please contact Apple directly through their automated help line, 1(800)MYAPPLE. -
Error -2003: a data handler needed by the movie could not be found
Hello.
I just purchased QuickTime Pro and the MPEG-2 add-on for it, for the single purpose of transcoding some MPEG-2 recordings to H.264. However, when I try to open any of my MPEG-2 files in Quicktime, I get the message: "error -2003: a data handler needed by the movie could not be found (my-filename.mpg)"
I can play these files in a number of different free players--VLC, Mplayer, Windows Media Player, RealPlayer... but not in the player I paid $50 for.
Can someone please help me?That doesn't really help. Besides, I haven't even got to the point where I'm trying to export. I get this error message when I try to open the file. I can't even play back the clip.
And the MPEG-2 page clearly states: "The QuickTime MPEG-2 Playback Component provides QuickTime users with the ability to import and play back MPEG-2 content, including both multiplexed (a.k.a. muxed, where the audio and video tracks are interleaved together into one track) and non-multiplexed (a.k.a. elementary) streams."
Also, Streamclip crashes when I try to load my MPEG-2 clips, so that's not going to work (and even if it did, I am trying to find a simple way to take the HDTV content I've recorded off the air and get it onto my AppleTV--I want fewer steps, not more).
Looks like I'll have to waste some time calling customer service to get a refund, since there's no way to do this via the website. -
I have a bose speakers and error on my iphone bluetooth device gave the skip and not as now bring up the device again, help please!
Try toggle Bluetooth off and on. You can also try a reset all settings (your content won't be deleted).
-
After upgrading to 3.6.8 none of the extensions load even though there are updates available. The updates will not install and even though the error states to look at the console error log there are no errors listed in the log. All extensions are listed in Addons>Extensions.
== This happened ==
Every time Firefox opened
== Upgrading to newer Firefox version (3.6.8)I have been having the same issue for the last two weeks. No real indication as to why it ever began other than I had turned off my router and Airport Extreme Base Station off for a weekend while I was away from my place.
iPad, iPhone, iPod Touch, all have no issues at all with my Airport Extreme Base Station. Can stay connected throughout my living room, bathroom, bedroom, no issues whatsoever.
My 5 month old MacBook Pro 2.66 GHz Core i7 Airport is sometimes perfect, able to connect, DHCP, and browse without issue. Then, for no reason, I won't be able to join my wireless network, or when I can join, I can't pick up an IP address. And then it will connect, pick up and IP, and then it won't browse. No real rhyme or reason to when this will happen, or when it works.
I thought that it was an issue with my MacBook Pro, but then my sister visited with her brand new MacBook Pro 2.26 Intel Core 2 Duo, and while a month ago she was able to connect, DHCP, and browse without issue, this weekend she had all of the same issues I was having.
My XBOX 360 and MacBook Pro have absolutely no issues with the wired connection. Only my WAN seems to have this issue.
Did you ever find anything more to this?
Maybe you are looking for
-
Can't drag songs to playlist????
for some reason, on my wife's itunes (not mine, mine, on the same computer is fine) it will not allow her to drag songs from her library into a playlist. I've never had this problem with mine, so I'm not sure what the problem is. Any help is greatly
-
5800 won't connect to internet - help!
My 5800XM has stopped connecting to the internet. If I go to, say the Ovi Store, I get the frot page, but instead of going to the Store, it returns to the previous screen. The same happens with other websites, too. The phone usually asks how I wis
-
How to use dreamweaver to check scripts.
I am both new to scripting and in using dreamweaver, I n eed to be able to copy an asp code and paste in dreamweaver and c ontinue with it, can anyone please help me on how to do this? , I a m testing dream weaver cs4
-
Looking for Video Camera to measure crack length??????
I need to measure crack length in fatigue test of an Aluminium sample automatically. For example, the camera can take shots (Images) every 4000 cycles (fatigue load cycles), maybe more cycles. For my test, I need to measure both sides crack length (r
-
Plugins & sampltank not showing up for use?
Hi there, I am still having trouble with plugins, can anyone help? Firstly, after installing and ensuring the AU ones are installed, my plugins do not show up for use in channels etc. they work perfectly in both Bias & ProTools though. i) I downloade