Error occurred when modifying array

I have recently built a new machine with the stuff listed in my profile. I have trawled these formums but have not found any with the specific problem- given that i have not read every thing written perhaps some one can shed some light onto this problem.
I have a single Seagate Barracuda 120GB SATA drive that is recognised by the Promise BIOS after you press F6 (you get a "no Array defined" error and F6 to setup array or ESC to continue boot.
Once in the Bios you are offered (correctly) the performance option and all the seagates parameters are recognised correctly. This is true in option 1 auto and 3 define array. So you select Ctrl Y to build your array and get
"Error occurred when modifying array. System is going to Reboot ! press any key to reboot"
I don't know where to begin on this. the machine has no OS on it as I hoped to install XP onto this drive and have Mandrake on the 4GB.
Any ideas anyone.
P.S.
I have lots of cooling and a 400W PSU. :]

hi
400w psu does not say ANYTHING.
for example an enermax 350w has MUCH more power than a q-tec 550w.
post amps on the 3.3v 5v and 12v rails on the psu.
should be written on a label on the psu.
k7n2 is VERY picky about memory and i dont think your memory is approved nforce2 memory.
there is a thread about memory at the top of this forum.
try other memory if you have it.
could also try http://www.memtest86.org
its a mem test program.
try to remove zip.
have seen alot of people having strange problem due to a zip drive.
bye

Similar Messages

Data Quality vendor-specific error: An error occurred when calling function 'sdq_init_connector ()' in connector ": "(-8) Exception!." Detailed error message: Exception thrown by Java: java.lang.UnsatisfiedLinkError: nio (Not found in com.ibm.oti.vm.boots

When attempting to create a new Account in siebel integrated with OEDQ the following error occurs.
ERROR
Data Quality vendor-specific error: An error occurred when calling function 'sdq_init_connector ()' in connector ": "(-8) Exception!." Detailed error message: Exception thrown by Java: java.lang.UnsatisfiedLinkError: nio (Not found in com.ibm.oti.vm.bootstrap.library.path)(SBL-APS-00118)
STEPS
The issue can be reproduced at will with the following steps:
1) from EDQ director we have imported the EDQ_CDS,EDQ-REFERENCE DATA & EDQ_HISTORICAl DATA packages sucessfully.
2) Created dnd.param file in SIebel server SDQCOnnector folder.
3) Copied the libdnd.so file to siebsrvr lib directory(32 bit)
3) In dnd.param file we have mentioned the javalib file and instllation directory path(<Siebsrvr roo>/dnd/install)
4) Unzipped the EDQ-Siebel Connector files in dnd/install folder
5) Copied the dnd.properties file in dnd/install directory and modified it accordingly to point to installed EDQ instance.
6) Configured the Siebel components for EDQ integration.
7) Realtime EDQ jobs are running.
8) Create a new Account
Env details are
On : 8.2.2.14 [IP2014] version, Client Functionality
EDQ 11.1.1.7.4
IBM JDK 1.7 32 bit
Using Open UI
Any Champ have faced this issue and overcame it please let me know the resolution steps. your help is
Regards
Monoj Dey
9007554589

Hi Monoj,
A few questions:
- What OS is Siebel running on?
- What version of the Siebel connector are you using?
- Which libdnd.so file are you using?
- What's the contents of your dnd.parms file?
thanks,
Nick

Error occur when create a provider for the sample of JPDK1.4

I am trying to install JPDK 1.4 in Oracle 9iAS.
Testing the sample successfully and I received a test page informing me that the sample worked.
After I follow the instruction to create a new provider and press the 'apply' button, the following error occur:
Error: An error occurred when attempting to call the providers register function. (WWC-43134)
The following error occurred during the call to Web provider: Unable to initialize new provider instance: java.lang.NumberFormatException: (WWC-43147)
I didn't modify any coding in jpdk. But, Why an error about Number.FormatException occur?
null

[28/05/2001 12:09:50:996 CST] discoservlet/oracle.disco3iv.Disco3iv: init
[28/05/2001 12:09:50:996 CST] discoservlet/oracle.disco3iv.Disco3iv: Initializing Discoverer 3i Viewer (3.3.57.25)
[28/05/2001 12:09:54:931 CST] discoservlet/oracle.disco3iv.Disco3iv: Initialized Discoverer 3i Viewer (3.3.57.25)
[28/05/2001 12:09:56:944 CST] sample/init
[28/05/2001 12:12:33:019 CST] sample/init
[28/05/2001 12:12:35:653 CST] sample/init
[28/05/2001 12:12:54:670 CST] sample/init
[28/05/2001 12:19:01:367 CST] discoservlet/oracle.disco3iv.Disco3iv: destroy
[28/05/2001 12:19:01:748 CST] discoservlet/oracle.disco3iv.Disco3iv: init
[28/05/2001 12:19:01:748 CST] discoservlet/oracle.disco3iv.Disco3iv: Initializing Discoverer 3i Viewer (3.3.57.25)
[28/05/2001 12:19:02:048 CST] discoservlet/oracle.disco3iv.Disco3iv: Initialized Discoverer 3i Viewer (3.3.57.25)
[28/05/2001 12:23:20:600 CST] discoservlet/oracle.disco3iv.Disco3iv: init
[28/05/2001 12:23:20:600 CST] discoservlet/oracle.disco3iv.Disco3iv: Initializing Discoverer 3i Viewer (3.3.57.25)
[28/05/2001 12:23:21:882 CST] discoservlet/oracle.disco3iv.Disco3iv: Initialized Discoverer 3i Viewer (3.3.57.25)
[28/05/2001 12:35:15:878 CST] discoservlet/oracle.disco3iv.Disco3iv: destroy
[28/05/2001 12:35:16:229 CST] discoservlet/oracle.disco3iv.Disco3iv: init
[28/05/2001 12:35:16:229 CST] discoservlet/oracle.disco3iv.Disco3iv: Initializing Discoverer 3i Viewer (3.3.57.25)
[28/05/2001 12:35:16:519 CST] discoservlet/oracle.disco3iv.Disco3iv: Initialized Discoverer 3i Viewer (3.3.57.25)
[28/05/2001 12:36:43:204 CST] page/oracle.webdb.page.ParallelServlet: init
[28/05/2001 12:36:43:234 CST] page/Starting a pool of 25 handlers.
[28/05/2001 12:42:18:977 CST] oracle.jsp.JspServlet: init
[28/05/2001 12:42:19:337 CST] JspServlet: unable to dispatch to requested page: java.io.FileNotFoundException: d:\servlet\login.jsp (The system cannot find the file specified)
at java.io.FileInputStream.open(Native Method)
at java.io.FileInputStream.<init>(FileInputStream.java:68)
at oracle.jsp.provider.JspFilesystemResource.fromStream(JspFilesystemResource.java)
at oracle.jsp.provider.JspFilesystemResource.fromReader(JspFilesystemResource.java)
at oracle.jsp.app.JspAppLoader.reloadPage(JspAppLoader.java)
at oracle.jsp.app.JspAppLoader.loadPage(JspAppLoader.java)
at oracle.jsp.app.JspAppLoader.getPage(JspAppLoader.java)
at oracle.jsp.app.JspApplication.dispatchRequest(JspApplication.java)
at oracle.jsp.JspServlet.doDispatch(JspServlet.java)
at oracle.jsp.JspServlet.internalService(JspServlet.java, Compiled Code)
at oracle.jsp.JspServlet.service(JspServlet.java)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:588)
at org.apache.jserv.JServConnection.processRequest(JServConnection.java)
at org.apache.jserv.JServConnection.run(JServConnection.java)
at java.lang.Thread.run(Thread.java:479)
[28/05/2001 12:43:13:645 CST] JspServlet: unable to dispatch to requested page: java.io.FileNotFoundException: d:\servlet\login.jsp (The system cannot find the file specified)
at java.io.FileInputStream.open(Native Method)
at java.io.FileInputStream.<init>(FileInputStream.java:68)
at oracle.jsp.provider.JspFilesystemResource.fromStream(JspFilesystemResource.java)
at oracle.jsp.provider.JspFilesystemResource.fromReader(JspFilesystemResource.java)
at oracle.jsp.app.JspAppLoader.reloadPage(JspAppLoader.java)
at oracle.jsp.app.JspAppLoader.loadPage(JspAppLoader.java)
at oracle.jsp.app.JspAppLoader.getPage(JspAppLoader.java)
at oracle.jsp.app.JspApplication.dispatchRequest(JspApplication.java)
at oracle.jsp.JspServlet.doDispatch(JspServlet.java)
at oracle.jsp.JspServlet.internalService(JspServlet.java, Compiled Code)
at oracle.jsp.JspServlet.service(JspServlet.java)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:588)
at org.apache.jserv.JServConnection.processRequest(JServConnection.java)
at org.apache.jserv.JServConnection.run(JServConnection.java)
at java.lang.Thread.run(Thread.java :479)
[28/05/2001 12:50:16:243 CST] discoservlet/oracle.disco3iv.Disco3iv: destroy
[28/05/2001 12:50:16:483 CST] discoservlet/oracle.disco3iv.Disco3iv: init
[28/05/2001 12:50:16:483 CST] discoservlet/oracle.disco3iv.Disco3iv: Initializing Discoverer 3i Viewer (3.3.57.25)
[28/05/2001 12:50:16:904 CST] discoservlet/oracle.disco3iv.Disco3iv: Initialized Discoverer 3i Viewer (3.3.57.25)
[28/05/2001 12:50:16:954 CST] sample/init
[28/05/2001 12:50:22:462 CST] sample/init
[28/05/2001 12:50:25:867 CST] sample/init
[28/05/2001 12:51:40:564 CST] discoservlet/oracle.disco3iv.Disco3iv: destroy
[28/05/2001 12:51:40:745 CST] discoservlet/oracle.disco3iv.Disco3iv: init
[28/05/2001 12:51:40:745 CST] discoservlet/oracle.disco3iv.Disco3iv: Initializing Discoverer 3i Viewer (3.3.57.25)
[28/05/2001 12:51:41:055 CST] discoservlet/oracle.disco3iv.Disco3iv: Initialized Discoverer 3i Viewer (3.3.57.25)
[28/05/2001 12:51:41:055 CST] sample/init
[28/05/2001 12:51:41:335 CST] oracle.jsp.JspServlet: init
[28/05/2001 12:51:49:347 CST] sample/javax.servlet.ServletException: Unable to initialize new provider instance: java.lang.NumberFormatException:
at oracle.portal.provider.v1.http.HttpProvider.getProvider(HttpProvider.java:339)
at oracle.portal.provider.v1.http.HttpProvider.service(HttpProvider.java:246)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:588)
at org.apache.jserv.JServConnection.processRequest(JServConnection.java)
at org.apache.jserv.JServConnection.run(JServConnection.java)
at java.lang.Thread.run(Thread.java:479)
[28/05/2001 12:53:51:272 CST] discoservlet/oracle.disco3iv.Disco3iv: destroy
[28/05/2001 12:53:51:272 CST] sample/destroy
[28/05/2001 12:53:51:493 CST] discoservlet/oracle.disco3iv.Disco3iv: init
[28/05/2001 12:53:51:493 CST] discoservlet/oracle.disco3iv.Disco3iv: Initializing Discoverer 3i Viewer (3.3.57.25)
[28/05/2001 12:53:51:783 CST] discoservlet/oracle.disco3iv.Disco3iv: Initialized Discoverer 3i Viewer (3.3.57.25)
[28/05/2001 12:53:51:783 CST] sample1/init
[28/05/2001 12:53:51:813 CST] oracle.jsp.JspServlet: init
[28/05/2001 12:55:04:307 CST] sample1/javax.servlet.ServletException: Unable to initialize new provider instance: java.lang.NumberFormatException:
at oracle.portal.provider.v1.http.HttpProvider.getProvider(HttpProvider.java:339)
at oracle.portal.provider.v1.http.HttpProvider.service(HttpProvider.java:246)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:588)
at org.apache.jserv.JServConnection.processRequest(JServConnection.java)
at org.apache.jserv.JServConnection.run(JServConnection.java)
at java.lang.Thread.run(Thread.java:479)
[28/05/2001 12:57:35:685 CST] sample1/javax.servlet.ServletException: Unable to initialize new provider instance: java.lang.NumberFormatException:
at oracle.portal.provider.v1.http.HttpProvider.getProvider(HttpProvider.java:339)
at oracle.portal.provider.v1.http.HttpProvider.service(HttpProvider.java:246)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:588)
at org.apache.jserv.JServConnection.processRequest(JServConnection.java)
at org.apache.jserv.JServConnection.run(JServConnection.java)
at java.lang.Thread.run(Thread.java:479)
[28/05/2001 12:57:44:798 CST] sample1/javax.servlet.ServletException: Unable to initialize new provider instance: java.lang.NumberFormatException:
at oracle.portal.provider.v1.http.HttpProvider.getProvider(HttpProvider.java:339)
at oracle.portal.provider.v1.http.HttpProvider.service(HttpProvider.java:246)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:588)
at org.apache.jserv.JServConnection.processRequest(JServConnection.java)
at org.apache.jserv.JServConnection.run(JServConnection.java)
at java.lang.Thread.run(Thread.java:479)
[28/05/2001 13:02:18:261 CST] sample1/javax.servlet.ServletException: Unable to initialize new provider instance: java.lang.NumberFormatException:
at oracle.portal.provider.v1.http.HttpProvider.getProvider(HttpProvider.java:339)
at oracle.portal.provider.v1.http.HttpProvider.service(HttpProvider.java:246)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:588)
at org.apache.jserv.JServConnection.processRequest(JServConnection.java)
at org.apache.jserv.JServConnection.run(JServConnection.java)
at java.lang.Thread.run(Thread.java:479)

[SOLVED] Error occur when viewing youtube videos firefox 14.0.1

'''''PROBLEM SOLVED!'''''
Error occur when viewing youtube videos firefox 14.0.1, any solution? tired of reading/finding exact solution.
This is annoying me.
Application Basics
Name
Firefox
Version
14.0.1
User Agent
Mozilla/5.0 (Windows NT 6.1; rv:14.0) Gecko/20100101 Firefox/14.0.1
Profile Folder
Show Folder
Enabled Plugins
about:plugins
Build Configuration
about:buildconfig
Crash Reports
about:crashes
Memory Use
about:memory
Extensions
Name
Version
Enabled
ID
RealPlayer Browser Record Plugin
15.0.4
false
{97E22097-9A2F-45b1-8DAF-36AD648C7EF4}
Important Modified Preferences
Name
Value
browser.cache.disk.capacity
1048576
browser.cache.disk.smart_size.first_run
false
browser.cache.disk.smart_size_cached_value
911360
browser.places.smartBookmarksVersion
4
browser.startup.homepage_override.buildID
20120713134347
browser.startup.homepage_override.mstone
14.0.1
extensions.lastAppVersion
14.0.1
network.cookie.prefsMigrated
true
places.history.expiration.transient_current_max_pages
46736
privacy.sanitize.migrateFx3Prefs
true
Graphics
Adapter Description
Intel(R) HD Graphics
Vendor ID
0x8086
Device ID
0x0046
Adapter RAM
Unknown
Adapter Drivers
igdumdx32 igd10umd32
Driver Version
8.15.10.2119
Driver Date
4-21-2010
Direct2D Enabled
Blocked for your graphics driver version. Try updating your graphics driver to version 8.15.10.2202 or newer.
DirectWrite Enabled
false (6.1.7600.16699)
ClearType Parameters
ClearType parameters not found
WebGL Renderer
Blocked for your graphics driver version. Try updating your graphics driver to version 8.15.10.2202 or newer.
GPU Accelerated Windows
0. Blocked for your graphics driver version. Try updating your graphics driver to version 8.15.10.2202 or newer.
JavaScript
Incremental GC
1
Library Versions
Expected minimum version
Version in use
NSPR
4.9
4.9
NSS
3.13.5.0 Basic ECC
3.13.5.0 Basic ECC
NSS Util
3.13.5.0
3.13.5.0
NSS SSL
3.13.5.0 Basic ECC
3.13.5.0 Basic ECC
NSS S/MIME
3.13.5.0 Basic ECC
3.13.5.0 Basic ECC

Do you have all pop-up blockers disabled?
FYI: Please lose all the formatting in your posts.Simply makes it very difficult to follow.

Another "An error occurred when attempting to change modules" error

Hello all:
After using Adobe Photoshop Lightroom on Mac OSX trouble free for the past 6 months, I opened up Lightroom today and received the following error: "An error occurred when attempting to change modules." I had not made any changes in between when it worked normally and when the error started to occur. I beleive the last thing I did before this error occurred was to go into the Print Module.
Other information--I keep all my RAW .NEF files on an external Firewire (800) 750 GB drive. This is on Mac OS X 10.5 running Adobe Photoshop Lightroom 1.3 and also with 1.4.1. I'm running an iMac 20" with dual-core 2.2 Ghz Intel processors and 4 GB of RAM. I have around 25k images total.
When I noticed this problem, I was on Lightroom 1.3. I immediately upgraded to 1.4.1, which did not solve the problem. I have also tried many suggestions in the forums including uninstalling the application and removing the .plist file.
I thought I had come up with a solution by creating a new catalog, then importing the former into it. While this seems to work immediately after the import process, as soon as I close it, the problem manifests itself again.
More details that may or (likely) may not help:
- Going to the Develop and Print Modules gives me no problems. However, when I click on Library, Slideshow, or Web, I see the error.
- I upgraded my Mac to the latest patch level after observing this error to no avail.
So it looks like my choices are to create a new file and reimport every single time, or lose all of the work I've done for the past 6 months on thousands of images.
Can anyone please help???? I promise to post the solution when we fix this darn thing so others may benefit. I'd be happy to run through any troubleshooting that y'all would suggest outside of switching to a Canon.
Thanks!!!!
Matt

I'd first check for the existence of a file ending in .lock, which should be present when LR is in use, but if it exists when LR is quit, it can cause problems, and should be deleted.
Please post back your results.

PL/SQL: ORA-04052: error occurred when looking up remote object.

Hi All,
I'm getting the following error message while executing a PL/SQL Block.
PL/SQL: ORA-04052: error occurred when looking up remote object UPLDUSER.filestatushistory@FTS
ORA-00604: error occurred at recursive SQL level 1
ORA-03106: fatal two-task communication protocol error
ORA-02063: preceding line from FTSStatement
declare
v_coun number;
begin
select count(*) into v_coun
from updluser.filestatushistory@fts;
end;Back ground of the situation as follows,
My DataBase version 10.2.0.3 DB Name :DB1
Table Owner : UPLDUSER
Table Name : FILESTATUSHISTORY
I have a report user on the same database and I have grant all on the above table to report user
Report User : RPT_FTS
SQL> GRANT ALL ON FILESTATUSHISTORY_V TO RPT_FTS;Now Please find the below database details where I'm getting subjected error.
Database version : 9.2.0.8
DB Name : DB2
User Name : RPT_REPORTS
I Have create a dblink from RPT_REPORTS to RPT_FTS on DB1 and the dblink works fine. But getting the above error while running it.
but When I do the same other 10.2.0.3 db , the above PL/SQL block works fine without any problem.
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Now the strange about this is that I have Created a new table on DB1 db like below;
SQL> CREATE TABLE UPLDUSER.ABC AS SELECT * FROM FILESTATUSHISTORY;and retry my code on DB2 (9.2.0.8) after changing the table to ABC and it worked. Now I don't know whats wrong with a original table(FILESTATUSHISTORY).
To over come the problem and a work-a-round method I create a view on the DB1 (RPT_FTS) like the below
SQL> CREATE VIEW FILESTATUSHISTORY AS SELECT * FROM UPLDUSER.FILESTATUSHISTORY;and was able to run the PL/SQL block Remotely.
Just wants To know what whould have been the cause for this .
Cheers
Kanchana

Hi Kanchana,
Perhaps following link of google search has answer to your query
ORA-04052. The search result contains some useful articles whose URLs I shan't post in the forums.
HTH!
*009*

Why does an unknown error occur when I try to save a document as a word file?

why does an unknown error occur when I try to save a document as a Word file?

Hi Judy,
Deleting the Preferences files seems to be missing from your list.
Quit AppleWorks,
In the Finder, go to:
username > Library > Preferences
In the Preferences folder:
Locate and Delete the File com.apple.appleworks.plist
Locate and Open the Folder AppleWorks
In the AppleWorks folder, delete the following files:
AppleWorks 6 Assistants Cache
AppleWorks 6 Preferences
AppleWorks 6 Translators Cache
Optional:
AppleWorks Button Bars
This file contains your Button Bar preferences. If you have made changes to the Button Bar, but hanve NO issues that can be traced to the Button Bar, it may be left in place.
Regards,
Barry

I have Lightroom 5 installed on my MacBook Air but when I try to open the program I receive the message "An error occurred when attempting to change modules". I uninstalled, emptied trash and re-installed but I continue to get the same message.

I have Lightroom 5 installed on my iMac which I downloaded (uploaded?) to my MacBook Air (via wi-fi) but unlike the iMac, I'm unable to use the program on the MacBook Air. When I open the program on the iMac and click 'file', (as people using the program would know) there are 21 options - import pics, export, etc, etc - however, in the version on the MacBook Air, opening 'file' gives me four options - New Catalogue, Open Catalogue, Page Setup and Printer - and with that comes the pop-up message "An error occurred when attempting to change modules". Any ideas please?

A forum thread from 3 years ago talking about LR 1.x which had this problem seems to need permissions fixed or new folders created with the corrected permissions. You might try doing a repair permissions for your user and/or run LR as an administrator user. I am a PC person so cannot tell you exactly how to do that.
https://forums.adobe.com/message/1457020

An error occurred when processing the spool request. (Possibly due to memory problems)

Hi SAP,
My backgroud job is failing with log as shown below
Job started
Step 001 started (program ZMRS0065, variant SUS
Step 002 started (program ZDRS0090, variant SUS
Step 003 started (program ZFRS0305, variant SUS
Step 004 started (program ZFRS0300, variant SUS
Access error
Job cancelled after system exception ERROR_MESSAGE
An error occurred when processing the spool request. (Possibly due to memory problems)
Kindly help out in this issue
Regards
Mohammed

Hello Mohammed,
Have you seen any error in your SM21 system log and developer trace of spool work process
during that time?
The maximum size when create spool is 2GB.Pls also check if you are creating a spool
larger than it.
Best Regards
Jie Bai

Internal error occured when writing

Hi all
I successfully imported an APO planning area into the quality systems, however the same request ends with error 12 in the production system. Landscape is SCM 5.0 sp8 with BI 7.0 sp12. When i checked the import job RDDEXECL (user DDIC), it shows:
Date Time Message text Message class Message no. Message type
07/08/2007 00:02:57 Job started 00 516 S
07/08/2007 00:02:57 Step 001 started (program RDDEXECL, variant , user ID DDIC) 00 550 S
07/08/2007 00:02:57 All DB buffers of application server <server_name> were synchronized PU 170 S
07/08/2007 00:03:17 <b>Internal error occurred when writing</b> D0 054 E
07/08/2007 00:03:17 Job cancelled after system exception ERROR_MESSAGE 00 564 A
I thought there will be an ABAP dump, I found this internal error (in bold in the log above). I tried searching for info on this but no help, it does not says error writing to what? Please help.
Thanks
Ali

It seems a syncronization problem..
You can create a customer message providing the following information:
1. The symptoms that occurred
2. The highest Support Package
3. The current SAP_BASIS Support Package level
4. The queue that is currently selected
Header Data

Error message in TRFC 'An SQL error occurred when accessing a table'

Hi all,
Can any one tell what this below error message is about in while go into TRFC
'An SQL error occurred when accessing a table'.
and please tell me how to solve this problem.

Hi
Try to see what all tables are accessed by data source. and see if there is any lock on that..
If some other job is accessing that table - then there might be lock on that which is causing failure..
1) Try looking at ST22 dump also..
2) Try to do RSA3 in R/3 and if see if its is fetching any records or not..
Hoep it helps
--SA

Error in executing ABAP program. Error occurred when creating dataset

hi,
when I use LKM SAP ERP to Oracle (SQLLDR) to extract data from SAP ERP server. I execute my interface, and it's stop at extract data step.
This is message:
java.lang.RuntimeException: Error occured in open tool execute method...Error in executing ABAP program...Error in executing ABAP program...Error occurred when creating dataset/abc/ZODI_13001_6001_GLOBAL.txt
I tried others path name, tried slash or backslash. This is content in code tab
OdiSAPAbapExecute "-UPLOAD=1" "-EXECUTE=1" "-EXECUTEBASE_RKM=0" "-ZRFC_RUN_INSTALL=1" "-ABAP_PROGRAM_NAME=ZODI_13001_6001" "-HOST=10.86.87.24" "-USER=sv_hoa" "-PASSWORD=<@=snpRef.getInfo("SRC_PASS") @>" "-SAP_CLIENT=800" "-SAP_LANGUAGE=EN" "-SAP_SYSTEM_NUMBER=02" "-SAP_FUNCTION_GROUP_NAME=ZODI_FGR_13001" "-CONNECTION_POOL_NAME=SAP_ODI_ERP_POOL_10.86.87.24" "-CONNECTION_POOL_SIZE=10" "-FILE_DELIMITER=<@=""+(char)8@>" "-FILE_NAME=ZODI_13001_6001_GLOBAL.txt" "-FTP_HOST=10.86.82.108" "-FTP_USER=anh" "-FTP_PASSWORD=<@=sFtpPassword@>" "-FTP_PASSIVE_MODE=1" "-FTP_TRANSFER_TIMEOUT=100000" "-ODI_VARIABLE_NAMES=" "-ODI_VARIABLE_VALUES=" "-USER_ABAP_PARAMETER_NAMES=IV_DELIMITER,CHAR3;IV_FILENAME,CHAR255;IV_USER,CHAR35;IV_PWD,CHAR35;IV_HOST,CHAR35;IV_HASHVALUE,CHAR35;IV_PATH,CHAR35;IV_MAX_ROW_CNT,SYTABIX;IV_FETCH_BATCH_SIZE,SYTABIX;" "-USER_ABAP_PARAMETER_VALUES=<Value>" "-USER_ABAP_PARAMETER_SEPARATOR=<Value>" "-ABAP_TABLE_PARAMETERS=RETURN,BAPIRETURN;ET_FILE_RETURN,BAPIRET2" "-ABAP_EXPORT_PARAMETERS=ERRORMESSAGE;SY-MSGV1" "-LOG_FILE_NAME=C:\Users\anh\AppData\Local\Temp\SapAbapExecuteOpenTool_13001.log" "-FTP_PATH=/abc/" "-DEV_CLASS=ZODI_DEVCLASS" "-MAX_ROW_COUNT=" "-FETCH_BATCH_SIZE=100000" "-HASH_VALUE_MARKER=HVM" "-ABAP_PROGRAM_BODY=
*Final Type declarations
TYPES : BEGIN OF ty_final,
Y03HOCSINH_HOCSINH_ID TYPE
Y03HOCSINH-HOCSINH_ID,
Y03HOCSINH_MA_HOC_SINH TYPE
Y03HOCSINH-MA_HOC_SINH,
Y03HOCSINH_TEN_HOC_SINH TYPE
Y03HOCSINH-TEN_HOC_SINH,
Y03HOCSINH_GIOI_TINH TYPE
Y03HOCSINH-GIOI_TINH,
Y03HOCSINH_DIA_CHI TYPE
Y03HOCSINH-DIA_CHI,
Y03HOCSINH_GHI_CHU TYPE
Y03HOCSINH-GHI_CHU,
END OF ty_final.
*Final Temp Type Declarations
TYPES : BEGIN OF ty_final_tmp,
Y03HOCSINH_HOCSINH_ID TYPE
Y03HOCSINH-HOCSINH_ID ,
Y03HOCSINH_MA_HOC_SINH TYPE
Y03HOCSINH-MA_HOC_SINH ,
Y03HOCSINH_TEN_HOC_SINH TYPE
Y03HOCSINH-TEN_HOC_SINH ,
Y03HOCSINH_GIOI_TINH TYPE
Y03HOCSINH-GIOI_TINH ,
Y03HOCSINH_DIA_CHI TYPE
Y03HOCSINH-DIA_CHI ,
Y03HOCSINH_GHI_CHU TYPE
Y03HOCSINH-GHI_CHU ,
END OF ty_final_tmp.
*Final Target Type Declarations
TYPES : BEGIN OF ty_final_target,
C0_Y03HOCSINH_HOCSINH_ID TYPE
Y03HOCSINH-HOCSINH_ID,
C1_Y03HOCSINH_MA_HOC_SINH TYPE
Y03HOCSINH-MA_HOC_SINH,
C2_Y03HOCSINH_TEN_HOC_SINH TYPE
Y03HOCSINH-TEN_HOC_SINH,
C3_Y03HOCSINH_GIOI_TINH TYPE
Y03HOCSINH-GIOI_TINH,
C4_Y03HOCSINH_DIA_CHI TYPE
Y03HOCSINH-DIA_CHI,
C5_Y03HOCSINH_GHI_CHU TYPE
Y03HOCSINH-GHI_CHU,
END OF ty_final_target.
* Table type for Y03HOCSINH
TYPES : BEGIN OF ty_Y03HOCSINH,
HOCSINH_ID TYPE
Y03HOCSINH-HOCSINH_ID,
MA_HOC_SINH TYPE
Y03HOCSINH-MA_HOC_SINH,
TEN_HOC_SINH TYPE
Y03HOCSINH-TEN_HOC_SINH,
GIOI_TINH TYPE
Y03HOCSINH-GIOI_TINH,
DIA_CHI TYPE
Y03HOCSINH-DIA_CHI,
GHI_CHU TYPE
Y03HOCSINH-GHI_CHU,
END OF ty_Y03HOCSINH.
TYPES: BEGIN OF gs_text,
line(843) TYPE c,
END OF gs_text.
*Structure Declarations
DATA: wa_final_string TYPE string,
wa_final TYPE ty_final,
wa_final_target TYPE ty_final_target,
wa_Y03HOCSINH TYPE ty_Y03HOCSINH,
*Table Declarations
tt_final TYPE STANDARD TABLE OF ty_final,
tt_Y03HOCSINH TYPE STANDARD TABLE OF ty_Y03HOCSINH,
tt_final_target TYPE STANDARD TABLE
OF ty_final_target,
tt_final_tmp TYPE STANDARD TABLE OF ty_final_tmp,
tt_final_tmp1 TYPE STANDARD TABLE OF ty_final,
gt_result TYPE STANDARD TABLE OF gs_text,
*Variable Declarations
lv_path TYPE string,
lv_flag TYPE char1,
C0_Y03HOCSINH_HOCSINH_ID TYPE
STRING,
C1_Y03HOCSINH_MA_HOC_SINH TYPE
STRING,
C2_Y03HOCSINH_TEN_HOC_SINH TYPE
STRING,
C3_Y03HOCSINH_GIOI_TINH TYPE
STRING,
C4_Y03HOCSINH_DIA_CHI TYPE
STRING,
C5_Y03HOCSINH_GHI_CHU TYPE
STRING,
wa_final_tmp TYPE ty_final_tmp,
lv_file TYPE string,
lv_datum TYPE sy-datum,
lv_date TYPE char10,
wa_result TYPE string,
lv_delimiter type string,
lv_cnt TYPE sytabix,
*-Cursor Declaration
lv_Y03HOCSINH_dbcur TYPE cursor,
lv_tabix_frm TYPE sy-tabix.
lv_delimiter = iv_delimiter.
IF iv_hashvalue = 'HVM'.
*Open/delete output file
CONCATENATE iv_path iv_filename INTO lv_path.
*Check for file existence, if found, delete it
OPEN DATASET lv_path FOR INPUT
IN TEXT MODE
ENCODING DEFAULT.
IF sy-subrc EQ 0.
DELETE DATASET lv_path.
ENDIF.
*Open/create output file
OPEN DATASET lv_path FOR APPENDING
IN TEXT MODE
ENCODING DEFAULT.
IF sy-subrc EQ 0.
*Batch Processing
OPEN CURSOR WITH HOLD lv_Y03HOCSINH_dbcur FOR
SELECT HOCSINH_ID
MA_HOC_SINH
TEN_HOC_SINH
GIOI_TINH
DIA_CHI
GHI_CHU
FROM Y03HOCSINH.
DO.
*Check for the counter, only for first batch
*process new line is required...
lv_cnt = lv_cnt + 1.
REFRESH tt_Y03HOCSINH.
FETCH NEXT CURSOR lv_Y03HOCSINH_dbcur
APPENDING TABLE tt_Y03HOCSINH
PACKAGE SIZE IV_FETCH_BATCH_SIZE.
IF NOT tt_Y03HOCSINH IS INITIAL.
ELSE.
EXIT.
ENDIF.
LOOP AT tt_Y03HOCSINH INTO wa_Y03HOCSINH.
MOVE wa_Y03HOCSINH-HOCSINH_ID
TO wa_final_tmp-Y03HOCSINH_HOCSINH_ID.
MOVE wa_Y03HOCSINH-MA_HOC_SINH
TO wa_final_tmp-Y03HOCSINH_MA_HOC_SINH.
MOVE wa_Y03HOCSINH-TEN_HOC_SINH
TO wa_final_tmp-Y03HOCSINH_TEN_HOC_SINH.
MOVE wa_Y03HOCSINH-GIOI_TINH
TO wa_final_tmp-Y03HOCSINH_GIOI_TINH.
MOVE wa_Y03HOCSINH-DIA_CHI
TO wa_final_tmp-Y03HOCSINH_DIA_CHI.
MOVE wa_Y03HOCSINH-GHI_CHU
TO wa_final_tmp-Y03HOCSINH_GHI_CHU.
APPEND wa_final_tmp TO tt_final_tmp.
ENDLOOP.
free : tt_Y03HOCSINH.
LOOP AT tt_final_tmp INTO wa_final_tmp.
MOVE wa_final_tmp-Y03HOCSINH_HOCSINH_ID
TO wa_final_target-C0_Y03HOCSINH_HOCSINH_ID.
MOVE wa_final_tmp-Y03HOCSINH_MA_HOC_SINH
TO wa_final_target-C1_Y03HOCSINH_MA_HOC_SINH.
MOVE wa_final_tmp-Y03HOCSINH_TEN_HOC_SINH
TO wa_final_target-C2_Y03HOCSINH_TEN_HOC_SINH.
MOVE wa_final_tmp-Y03HOCSINH_GIOI_TINH
TO wa_final_target-C3_Y03HOCSINH_GIOI_TINH.
MOVE wa_final_tmp-Y03HOCSINH_DIA_CHI
TO wa_final_target-C4_Y03HOCSINH_DIA_CHI.
MOVE wa_final_tmp-Y03HOCSINH_GHI_CHU
TO wa_final_target-C5_Y03HOCSINH_GHI_CHU.
Append wa_final_target to tt_final_target.
ENDLOOP.
free : tt_final_tmp.
Clear wa_final_target.
IF NOT iv_max_row_cnt IS INITIAL.
Loop at tt_final_target into
wa_final_target TO iv_max_row_cnt.
MOVE wa_final_target-C0_Y03HOCSINH_HOCSINH_ID
TO C0_Y03HOCSINH_HOCSINH_ID.
MOVE wa_final_target-C1_Y03HOCSINH_MA_HOC_SINH
TO C1_Y03HOCSINH_MA_HOC_SINH.
MOVE wa_final_target-C2_Y03HOCSINH_TEN_HOC_SINH
TO C2_Y03HOCSINH_TEN_HOC_SINH.
MOVE wa_final_target-C3_Y03HOCSINH_GIOI_TINH
TO C3_Y03HOCSINH_GIOI_TINH.
MOVE wa_final_target-C4_Y03HOCSINH_DIA_CHI
TO C4_Y03HOCSINH_DIA_CHI.
MOVE wa_final_target-C5_Y03HOCSINH_GHI_CHU
TO C5_Y03HOCSINH_GHI_CHU.
CONCATENATE
C0_Y03HOCSINH_HOCSINH_ID
C1_Y03HOCSINH_MA_HOC_SINH
C2_Y03HOCSINH_TEN_HOC_SINH
C3_Y03HOCSINH_GIOI_TINH
C4_Y03HOCSINH_DIA_CHI
C5_Y03HOCSINH_GHI_CHU
INTO wa_final_string
SEPARATED BY lv_delimiter.
IF sy-tabix EQ 1 AND lv_cnt EQ 1.
CONCATENATE wa_final_string
lv_delimiter INTO wa_final_string.
ELSE.
CONCATENATE '<@=""+(char)8@>' lv_delimiter wa_final_string
lv_delimiter INTO wa_final_string.
ENDIF.
APPEND wa_final_string TO gt_result.
CLEAR : C0_Y03HOCSINH_HOCSINH_ID,
C1_Y03HOCSINH_MA_HOC_SINH,
C2_Y03HOCSINH_TEN_HOC_SINH,
C3_Y03HOCSINH_GIOI_TINH,
C4_Y03HOCSINH_DIA_CHI,
C5_Y03HOCSINH_GHI_CHU.
ENDLOOP.
ELSE.
Loop at tt_final_target into wa_final_target.
MOVE wa_final_target-C0_Y03HOCSINH_HOCSINH_ID
TO C0_Y03HOCSINH_HOCSINH_ID.
MOVE wa_final_target-C1_Y03HOCSINH_MA_HOC_SINH
TO C1_Y03HOCSINH_MA_HOC_SINH.
MOVE wa_final_target-C2_Y03HOCSINH_TEN_HOC_SINH
TO C2_Y03HOCSINH_TEN_HOC_SINH.
MOVE wa_final_target-C3_Y03HOCSINH_GIOI_TINH
TO C3_Y03HOCSINH_GIOI_TINH.
MOVE wa_final_target-C4_Y03HOCSINH_DIA_CHI
TO C4_Y03HOCSINH_DIA_CHI.
MOVE wa_final_target-C5_Y03HOCSINH_GHI_CHU
TO C5_Y03HOCSINH_GHI_CHU.
CONCATENATE
C0_Y03HOCSINH_HOCSINH_ID
C1_Y03HOCSINH_MA_HOC_SINH
C2_Y03HOCSINH_TEN_HOC_SINH
C3_Y03HOCSINH_GIOI_TINH
C4_Y03HOCSINH_DIA_CHI
C5_Y03HOCSINH_GHI_CHU
INTO wa_final_string
SEPARATED BY lv_delimiter.
IF sy-tabix EQ 1 AND lv_cnt EQ 1.
CONCATENATE wa_final_string
lv_delimiter INTO wa_final_string.
ELSE.
CONCATENATE '<@=""+(char)8@>' lv_delimiter wa_final_string
lv_delimiter INTO wa_final_string.
ENDIF.
APPEND wa_final_string TO gt_result.
CLEAR : C0_Y03HOCSINH_HOCSINH_ID,
C1_Y03HOCSINH_MA_HOC_SINH,
C2_Y03HOCSINH_TEN_HOC_SINH,
C3_Y03HOCSINH_GIOI_TINH,
C4_Y03HOCSINH_DIA_CHI,
C5_Y03HOCSINH_GHI_CHU.
ENDLOOP.
ENDIF.
free : tt_final_target.
IF NOT gt_result IS INITIAL.
CLEAR wa_result.
LOOP AT gt_result INTO wa_result.
TRANSFER wa_result TO lv_path.
ENDLOOP.
ENDIF.
REFRESH gt_result.
*End of main loop for batching
ENDDO.
*Close dataset
CLOSE DATASET lv_path.
CLOSE CURSOR lv_Y03HOCSINH_dbcur.
ELSE.
DATA: lv_mesg TYPE string.
CLEAR et_file_return.
et_file_return-type = 'E'.
CONCATENATE
'Error occurred when creating dataset' lv_path
INTO lv_mesg.
et_file_return-message = lv_mesg.
Append et_file_return.
ENDIF.
ELSE.
CLEAR et_file_return.
et_file_return-type = 'E'.
et_file_return-message =
'Installed ABAP program does not match interface definition'.
APPEND et_file_return.
ENDIF.
Thanks for help

r u able to figure it out..........i got the same error .......can someone help me fix this issue

The operation could not be completed because an error occurred when creating frame 6105 (error -1).

I am trying to share a project and after the 3% of sharing the project it appears this message.
The operation could not be completed because an error occurred when creating frame 6105 (error -1).
What can I do?? I need some help please!!

You need to set the FCP X Preferences to count in frames, locate that frame, delete the clip around it and replace with a fresh one.

The operation could not be completed because an error occurred when creating frame 19788 (error -1).

When attempting to build a quicktime movie from my video project on final cut pro I got this message "The operation could not be completed because an error occurred when creating frame 19788 (error -1)".

Kathy ...
Better to post your topic in the Final Cut Pro community here.

The operation could not be completed because an error occurred when creating frame 570 (error -1)

Hi everybody,just started with FCPX and the following occured:
The operation could not be completed because an error occurred when creating frame 570 (error -1)
Result is that i can not share to my hard disk.
If anybody could help me out here....?

CHange General preferences to show frames. Check what's happenING at the frame number. Maybe replace the shot.

Error occurred when modifying array

Similar Messages

Maybe you are looking for