Error on \Device\Harddisk0\D. on MS-6154VA

My os is windows xp sp2.
In the eventvwr.msc in system group i read:
disk
The driver get an error on the controller on \Device\Harddisk0\D.
My hd is a maxtor 60 gb.
I've run powermax and it show that the disk has not problem.
What's the problem?

Full Specs please.
Like ant3202 mentioned, install the chipset and UDMA/ATA/IDE controller drivers.

Similar Messages

  • 'An error was detected on device \Device\Harddisk0\D during a paging operation.'

    Hi,
    since a while (as far as i am able to roll back system log in event viewer) I am having strange issues in the sys log, as in the subject. It is a warning of disk event 51: 'An error was detected on device \Device\Harddisk0\D during a paging operation.'
    I have freed up 1/3 of each partition on the harddrive. Any idea where can i keep going to investigate?
    thx

    pogacsa,
    I have searched a bit about you issue in microsoft technet,and here's what they have got to say
    "An event ID 51 entry is a generic error entry for any type of error that occurs when Windows is paging information to input/output (I/O).
     A paging operation occurs when Windows either swaps a page of memory from memory to disk, or when Windows retrieves a page of memory from disk to memory."
    In this event, D, DR and FT, they all stand for a certain disk partition number. You can use the Registry or Disk Management to locate the certain disk.
    For further information, please refer to the following KBs:
    159865 How to distinguish a physical disk device from an event message 
    http://support.microsoft.com/kb/159865/en-us
    244780 Information about Event ID 51
    http://support.microsoft.com/kb/244780/en-us
    you may also want to check out this link from microsoft technet community as well.
    some of the resolutions mentioned there require you to modify your registry.Please DONOT attempt to modify the registry if you dont have enough prior knowledge about it
    Also try defragmenting your HDD once. 
    hope this info helps you
    Message Edited by vijaysaradhi on 06-03-2009 02:33 PM
    Cheers and regards,
    • » νιנαｿѕαяα∂нι ѕαмανє∂αм ™ « •
    ●๋•کáŕádhí'ک díáŕý ツ
    I am a volunteer here. I don't work for Lenovo

  • An error was detected on device \Device\Harddisk0 during a paging operation.

    Hi
    I have a Dell PE 2850 running Windows Server 2003 which is attached via SCSI to a Power Vault 220 SCSI disk enclosure.
    The server is beeping and in the eventvwr I see the following message:
    An error was detected on device \Device\Harddisk0 during a paging operation.
    There are no disk failure lights on the server so what is causing these errors in the Event Viewer?
    Thanks
    Paul

    The "error" doesn't have to mean that the disk is faulty, it's just that that specific write operation might have failed (for unknown reasons).
    That's all the light I can shed on it after looking through my event logs, I have a few of those too, but no errors anywhere else.Best regards
    Joachim Nässlander
    IT-Expert, Knowledge Factory
    (http://www.knowledgefactory.se)
    MVP Cluster
    Member of Microsoft Extended Experts Team (MEET)
    Blog: http://www.nullsession.com

  • Error \device\harddisk0\dr0 compiling

    Hi,
    since yesterday i got this error, a window, when I try to compile a file located in the hard disk:
    There is no a disk in the device. Insert a disk in \device\harddisk0\dr0.
    It appears several times, but it compiles correctly. The Java file is very very simple and does not access to the file system.
    I dont get any error if I compile in another partition or in another device, like a zip iomega.
    The machine works perfectly. There is no error in the event viewer. I can copy files in the hardisk and I dont get any error.
    I have installed Windows 2000 Professional Service Pack 3.
    Lastest drivers.
    Sdk 1.4.1_01. I have tried also with sdk 1.4.1_02
    I have made a scandisk and not problem at all.
    Any help will be very welcome.
    Thanks in advance.
    sergio.
    PS: it may be a hardware problem, but the problem is just with javac and java (compiling and running).

    found this:
    https://engineering.purdue.edu/ECN/mailman/archives/nt/2001-December/000331.html
    sounds like it might be relevant to your situation.
    Good luck (that's a frightening error message to get!)
    Lee

  • EventId: 32, disk - The driver detected that the device \Device\Harddisk0\DR0 has its write cache enabled

    Virtualized 2012 R2 Domain Controller running on hyper-V.  Every boot lists the following error three times:
    EventId: 32, disk - The driver detected that the device \Device\Harddisk0\DR0 has its write cache enabled. 
    Data corruption may occur.
    Having checked the virtual SCSI disks all have their write cache enabled, is this correct or do I need to take some action to prevent these events?

    Hi,
    This is normal and you can't change it. This tells AD that write caching is enabled so it uses a different method to store information.
    http://www.hyper-v.nu/archives/hvredevoort/2013/07/keeping-your-virtual-active-directory-domain-controllers-safe/
    More information there.
    Thanks
    Denis
    Regards,
    Denis Cooper
    MCITP EA - MCT
    Help keep the forums tidy, if this has helped please mark it as an answer
    Blog: http://www.windows-support.co.uk 
    Twitter:   LinkedIn:

  • Can anyone help me with Magicjack? after I purchased US number I am unable to log in on my Iphone, I keep getting an error "YOUR DEVICE IS NOT ON THIS ACCOUNT" I contacted MJ support but they are very much useless and dont know how to fix it!

    can anyone help me with Magicjack? after I purchased US number I am unable to log in on my Iphone, I keep getting an error "YOUR DEVICE IS NOT ON THIS ACCOUNT" I contacted MJ support but they are very much useless and dont know how to fix it!

    There's a whole lot to read in your post, and frankly I have not read it all.
    Having said that, this troubleshooting guide should help:
    http://support.apple.com/kb/TS1538
    In particular, pay attention to the mobile device support sections near the bottom, assuming you have already done the items above it.

  • Error publishing from Muse - "error updating device redirect setting"

    After recent upgrade of Muse I am getting an error message when publishing. The pages are published correctly but there is an error which prevents the final completion of the process. message = "Error updating device redirect settings click resume to try again." it never works. What is up? is this a Business Catalyst error or a a Muse error?

    I turned off the firewall, logged out from Creative Cloud and restarted my computer. After rebooting, I logged in to Creative Cloud, open Muse and connect to Business Catalyst without no problem,

  • Iphone 5- Won't show up in itunes. Error message " Device drivr software was not successfully installed. Please consult with your device manufacturer for assistance getting this device installed. Digital Still Camera- Failed" HELP!

    Error message  " Device driver software was not successfully installed. Please consult with your device manufacturer for assistance getting this device installed. Digital Still Camera- Failed" HELP!

    Hi, I was able to reformat my iPod and that worked. I read it on one of the threads and I am copy pasting the method below:
    I opened the "My Computer" window and right-clicked on my ipod, and then selected "Format". I select "Yes" to format since I don't have anything on the nano to delete anymore.
    I then Eject my nano from the computer and did a restart while the nano is disconnected from the computer.
    Once Windows finish loading I reconnect the USB to the nano(back of computer) which automatically pulls up iTune. It asked me to name the new ipod detected and created a playlist for that specific ipod name.
    Pasted from <http://discussions.apple.com/thread.jspa?threadID=1050784&tstart=15>
    Thanks!

  • Audio Stream Recorder - Error: Audio device is already being used by another prog

    I realized that Audio Stream Recorder is does not "work" through server list feature. So I am simply trying to use the manual method of adding URL's to the interface. However regardless of the type of stream, shoutcast, windows media or real audio, I receive the error "audio device is already being used by another program". Does anyone know how to fix this? I have closed my audio application etc to no avail. <RANT WARNING> I was very excited about using this application when I read about it. However an application that provides none of the stated features is not an application, its false advertising, since it clearly states on the box, help files and website this products "features". Anyway, it'ss very disappointing. Also, does anyone know what the supported steaming formats are, the help file say the application requires RealONE and Windows Media Player but does not mention audio stream formats? Thanks you in advance for any help.

    I have the same issue. I updated to the latest software, to no avail. My first suspicion is that some Microsoft patch caused this, but I cannot verify this.
    Apparently no one at Creative is very interested in this issue.

  • U530 Touch - Audio DRIVER ERROR - This device cannot start (Code 10) - Windows 7

    U530 - High definition audio device - ERROR - This device cannot start (Code 10) Windows 7, please see the picture
    Picture link (hosted on photobucket.com)
    I got all drivers up to date including the BIOS, everything is working fine (the sound works, microphone works...) but this error is kind of annoying to my eyes so if anyone know how to fix it please help.
    I tried to uninstall this and let windows update install it again => not worked, same problem.
    I tried to re-install the Realtek driver (uninstall - restart machine - install - restart machine) => same problem
    And another probelm which has not been solved yet is the Bluetooth icon keep blinking on battery mode (windows 7), you can see more in this thread

    What kind of reinmstall did you perform?  If you used the recovery media, then this will be pretty simple. Boot to the recovewry media again and this time select the Reinstall drivers and applications option. Find the audio driver on the list of available drivers, put a tick in the box to its left and then click on the install button in the lower right hand corner of the window. The driver will be installed.  Your list will be different than the following one, but this is only an example. 

  • My Iphone 4 will not start up, when i connect it to itunes i says : Activation error This device is not registered as part of the iPhone Developer Program.If you are a member of the Program, please register your device in the iPhone Developer Program Port

    my Iphone 4 will not start up, when i connect it to itunes i says : Activation error This device is not registered as part of the iPhone Developer Program.If you are a member of the Program, please register your device in the iPhone Developer Program Port

    Well, you downloaded a bootleg copy of iOS 7 beta and have installed it on your phone without being a developer. It has bricked your phone and you cannot get help here because doing what you did has voided your warranty. Have a nice day.

  • I'm receiving error Boot Device Not Found and Hard disk not exist when I boot up my laptop

    I'm receicing the error Boot Device Not Found when i power on my HP G60-235DX laptop.  After following HP's recommended troubleshooting steps, I receive error Hard disk not exist.  Hmmmm....that's a little concerning.  My guess is I need a new hard drive?    I have the 17 recovery disks I made when I setup this laptop, however I'm not sure if they will resolve this issue.  Any suggestions?

    One of 3 things has happened, listed from most likely to least likely
    1. Hard drive has died, replace it with one of the same size or larger, then use the HP recovery discs to re-install windows.
    2, The motherboard has serious problems. (Replace the notebook)
    3. The hard drive cable that connects it to the motherboard has somehow failed, not very likely. (replace the cable)
    Replace the hard drive with a new one and use your recovery discs to get Windows back on it.
    Here is your service manual, will show you how to replace the hard drive
    http://h10032.www1.hp.com/ctg/Manual/c02985882.pdf
    Recovery Instructions for Vista
    Recovery Instructions for Windows 7

  • Install from SCSI CD fails: ERROR: boot device didn't show up after 30

    I have a x86 based server w/SCSI HD and DVD drive. 
    Install fails with following.
    Waiting 30 seconds for device /dev/disk/by-label/ARCH_201108
    ERROR: boot device didn't show up after 30 seconds
       Falling back to interactive prompt
       You can try to fix the problem manually, logout when you are finished
    sh: can't access tty; job contro turned off
    [ramfs /]#
    I hooked up a IDE DVD drive and using same CD installs OK.  Then, once installed, I switch my DVD back to SCSI that failed the install, and guess what?  Arch booted from my HD now recognizes the SCSI DVD drive, I can mount it and so on.  Looks to me like the install kernel doesn't support my SCSI DVD drive but the installed kernel does.
    I need the Arch install to work from the SCSI DVD drive on my system.  I'm trying to develop an Arch distro for my particular system, which there are about a dozen of in the field, they all have SCSI DVD and no IDE drives.  Will I have to add a SCSI driver to the boot kernel?  Or is my problem something else?
    I notice there is no /dev/disk/by-label (ther is a /dev/disk/by-id  by-label  and by-uuid).
    I do a:
    "[ramfs /]# lsmod | grep sr_mod"
    sr_mod        14951   0
    cdrom        36329   1   sr_mod
    scsi_mod    131482   7  sg,sr_mod,sd_mod,libata,mptspi,mptscsih,scsi_transport_spi
    [ramfs /]# lsmod | grep scsi
    mptscsih        20040   1   mptspi
    mptbase            63459    2   mptspi,pmtscsih
    scsi_transport_spi    20059   1   mptspi
    scsi_mod        131482  7   sg,sr_mod,sd_mod,libata,mptspi,mptscsih,scsi_stransport_spi

    scrath "I notice there is no /dev/disk/by-label (ther is a /dev/disk/by-id  by-label  and by-uuid)."
    Should be: I notice there is no /dev/disk/by-label (there is a /dev/disk/by-id  by-path  and by-uuid).

  • RMAN Delete Obsolete job fails due to Error Allocating Device

    Experts, I need help, please.
    This is 10.2.0.1 on Windows
    RMAN> DELETE NOPROMPT OBSOLETE;
    RMAN retention policy will be applied to the command
    RMAN retention policy is set to recovery window of 3 days
    allocated channel: ORA_DISK_1
    channel ORA_DISK_1: sid=130 devtype=DISK
    released channel: ORA_DISK_1
    RMAN-00571: ===========================================================
    RMAN-00569: =============== ERROR MESSAGE STACK FOLLOWS ===============
    RMAN-00571: ===========================================================
    RMAN-03002: failure of delete command at 05/15/2012 14:10:17
    ORA-19554: error allocating device, device type: SBT_TAPE, device name:
    ORA-27211: Failed to load Media Management Library
    I ran RMAN> configure device type 'SBT_TAPE' clear;
    but I still get the same error.
    I backup to Disk, not tape
    Notice the reference to SBT_TAPE:
    RMAN configuration parameters are:
    CONFIGURE DEVICE TYPE DISK BACKUP TYPE TO BACKUPSET PARALLELISM 1;
    CONFIGURE DEVICE TYPE SBT_TAPE PARALLELISM 1 BACKUP TYPE TO BACKUPSET; # default
    What do I need to do to be able to run DELETE OBSOLETE; ?
    Thanks, John

    as anand mention ,you've to reset this parameter to default value.
    and clear cmd with configure will remove it from configuration parameter
    see below
    RMAN> show all;
    RMAN configuration parameters are:
    CONFIGURE RETENTION POLICY TO REDUNDANCY 1;
    CONFIGURE BACKUP OPTIMIZATION OFF; # default
    CONFIGURE DEFAULT DEVICE TYPE TO DISK; # default
    CONFIGURE CONTROLFILE AUTOBACKUP OFF; # default
    CONFIGURE CONTROLFILE AUTOBACKUP FORMAT FOR DEVICE TYPE SBT_TAPE TO '%F'; # default
    CONFIGURE CONTROLFILE AUTOBACKUP FORMAT FOR DEVICE TYPE DISK TO '%F'; # default
    *CONFIGURE DEVICE TYPE 'SBT_TAPE' PARALLELISM 1 BACKUP TYPE TO BACKUPSET;*
    CONFIGURE DEVICE TYPE DISK PARALLELISM 2 BACKUP TYPE TO BACKUPSET;
    CONFIGURE DATAFILE BACKUP COPIES FOR DEVICE TYPE SBT_TAPE TO 1; # default
    CONFIGURE DATAFILE BACKUP COPIES FOR DEVICE TYPE DISK TO 1; # default
    CONFIGURE ARCHIVELOG BACKUP COPIES FOR DEVICE TYPE SBT_TAPE TO 1; # default
    CONFIGURE ARCHIVELOG BACKUP COPIES FOR DEVICE TYPE DISK TO 1; # default
    CONFIGURE MAXSETSIZE TO UNLIMITED; # default
    CONFIGURE ENCRYPTION FOR DATABASE OFF; # default
    CONFIGURE ENCRYPTION ALGORITHM 'AES128'; # default
    CONFIGURE ARCHIVELOG DELETION POLICY TO NONE; # default
    CONFIGURE SNAPSHOT CONTROLFILE NAME TO '/u01/app/oracle/product/10/db/dbs/snapcf_GG1.f'; # default
    RMAN> delete obsolete;
    RMAN retention policy will be applied to the command
    RMAN retention policy is set to redundancy 1
    RMAN-00571: ===========================================================
    RMAN-00569: =============== ERROR MESSAGE STACK FOLLOWS ===============
    RMAN-00571: ===========================================================
    RMAN-03002: failure of delete command at 05/16/2012 12:04:34
    ORA-19554: error allocating device, device type: SBT_TAPE, device name:
    ORA-27211: Failed to load Media Management Library
    Additional information: 2
    RMAN>  CONFIGURE DEVICE TYPE 'SBT_TAPE' clear;
    old RMAN configuration parameters:
    CONFIGURE DEVICE TYPE 'SBT_TAPE' PARALLELISM 1 BACKUP TYPE TO BACKUPSET;
    RMAN configuration parameters are successfully reset to default value
    RMAN> show all;
    RMAN configuration parameters are:
    CONFIGURE RETENTION POLICY TO REDUNDANCY 1;
    CONFIGURE BACKUP OPTIMIZATION OFF; # default
    CONFIGURE DEFAULT DEVICE TYPE TO DISK; # default
    CONFIGURE CONTROLFILE AUTOBACKUP OFF; # default
    CONFIGURE CONTROLFILE AUTOBACKUP FORMAT FOR DEVICE TYPE DISK TO '%F'; # default
    CONFIGURE DEVICE TYPE DISK PARALLELISM 2 BACKUP TYPE TO BACKUPSET;
    CONFIGURE DATAFILE BACKUP COPIES FOR DEVICE TYPE DISK TO 1; # default
    CONFIGURE ARCHIVELOG BACKUP COPIES FOR DEVICE TYPE DISK TO 1; # default
    CONFIGURE MAXSETSIZE TO UNLIMITED; # default
    CONFIGURE ENCRYPTION FOR DATABASE OFF; # default
    CONFIGURE ENCRYPTION ALGORITHM 'AES128'; # default
    CONFIGURE ARCHIVELOG DELETION POLICY TO NONE; # default
    CONFIGURE SNAPSHOT CONTROLFILE NAME TO '/u01/app/oracle/product/10/db/dbs/snapcf_GG1.f'; # default
    RMAN> delete obsolete;
    RMAN retention policy will be applied to the command
    RMAN retention policy is set to redundancy 1
    allocated channel: ORA_DISK_1
    channel ORA_DISK_1: sid=1591 instance=GG1 devtype=DISK
    allocated channel: ORA_DISK_2
    channel ORA_DISK_2: sid=1627 instance=GG1 devtype=DISK
    no obsolete backups found

  • DVD Burning Error: Unknown device error. (0x73, 0x03.)

    I have been trying to burn a home movie using iDVD. I transferred the media successfully to my computer, followed all the steps, and was finally ready to burn the DVD. After waiting almost an hour through the burn process, it spit the DVD back out of my Macbook Pro and gave me the following message.
    *Errors were found during the burning process:*
    *The recording device reported the media error: Unknown device error. (0x73, 0x03.)*
    I don't really know what this means. Was the media corrupt? Or is there a problem with my DVD player? I have supplied my DVD and computer information below. I would appreciate all the help I can get. Thank you in advance!
    Courtney
    *MATSHITA DVD-R UJ-857D:*
    Firmware Revision: KCVB
    Interconnect: ATAPI
    Burn Support: Yes (Apple Shipping Drive)
    Cache: 2048 KB
    Reads DVD: Yes
    CD-Write: -R, -RW
    DVD-Write: -R, -RW, +R, +R DL, +RW
    Write Strategies: CD-TAO, CD-SAO, DVD-DAO
    Media: Insert media and refresh to show available burn speeds
    *Hardware Overview:*
    Model Name: MacBook Pro 15"
    Model Identifier: MacBookPro2,2
    Processor Name: Intel Core 2 Duo
    Processor Speed: 2.16 GHz
    Number Of Processors: 1
    Total Number Of Cores: 2
    L2 Cache: 4 MB
    Memory: 1 GB
    Bus Speed: 667 MHz
    Boot ROM Version: MBP22.00A5.B07
    SMC Version (system): 1.12f5

    Using the same media I've used for years (Verbatim 4x InkJet printable) and all of a sudden can't burn from the internal drive. I do have an external burner (7 disc standalone replicator with USB/FireWire 400) and hooked that up and burned to a disc from the same spindle with no problem, and then made a 3x replicate with the same media. So it's looking like my MacBook Pro's drive is failing?
    Laptop is plugged in and fully charged.
    DVD Studio Pro: Burn started, Fri Oct 23 22:42:55 2009
    DVD Studio Pro: Burning to DVD-R (MCC 01RG20) media with DAO strategy in MATSHITA DVD-R UJ-857E ZA0E via ATAPI.
    DVD Studio Pro: Requested burn speed was 4x, actual burn speed is 4x.
    DVD Studio Pro: Burn underrun protection is supported, and enabled.
    DVD Studio Pro: Write (10), block: 0, count: 64 -> 3/73/03 Medium Error, Power calibration area error
    DVD Studio Pro: Burn failed, Fri Oct 23 22:44:13 2009
    DVD Studio Pro: Burn sense: 3/73/03 Medium Error, Power calibration area error
    DVD Studio Pro: Burn error: 0x8002006D The device failed to calibrate the laser power level for this media.
    DVD Studio Pro: Burn started, Fri Oct 23 22:55:50 2009
    DVD Studio Pro: Burning to DVD-R (MCC 01RG20) media with DAO strategy in MATSHITA DVD-R UJ-857E ZA0E via ATAPI.
    DVD Studio Pro: Requested burn speed was 4x, actual burn speed is 4x.
    DVD Studio Pro: Burn underrun protection is supported, and enabled.
    DVD Studio Pro: Write (10), block: 0, count: 64 -> 3/73/03 Medium Error, Power calibration area error
    DVD Studio Pro: Burn failed, Fri Oct 23 22:57:08 2009
    DVD Studio Pro: Burn sense: 3/73/03 Medium Error, Power calibration area error
    DVD Studio Pro: Burn error: 0x8002006D The device failed to calibrate the laser power level for this media.

Maybe you are looking for