Error - The request could not be performed due to an error from the I/O device

Hello,
I have a Hyper-V server with a few virtual machines.
The host runs Windows Server 2012 R2 with Hyper-V.
VMs are Windows Server 2012R2 Generation 2 and Windows Server 2003 Generation 1.
All VMs running on VHDX on local host disks, no raid, no storage. Most VMs run on dedicated disks.
I am having the following error when I demand large amount of I/O on VMs:. "The request could not be performed due to an error from the I/O device"
This error happens when I run robocopy which requires large amount of writing, or on a SQL 2014 VM which also requires many reads and writes.
Whenever this error occurs, the replicas of the VMs require resynchronization and the MSSQL service stops.
Analyzing the events of the Host, I find the following warning multiple times: "The IO operation at logical block address 0x31fd01 for Disc 4 (PDO name: \ Device \ 0000005d) was retried." Disc 4 is where SQL runs.
Is there any special configuration that must be done to avoid these errors?
Thank you!
Rafael

Hi Eng.Rafael Grecco,
>>Analyzing the events of the Host, I find the following warning multiple times: "The IO operation at logical block address 0x31fd01 for Disc 4 (PDO name: \ Device \ 0000005d) was retried." Disc 4 is where SQL runs.
>>Chkdsk /r didn't return any error.
It seems that it is not a hyper-v issue .
I would suggest you to keep the driver up-to-date for your hyper-v host .
In addition , here is a similar thread :
http://answers.microsoft.com/en-us/windows/forum/windows_8-hardware/the-io-operation-at-logical-block-address-for-disk/23c32152-c2a6-4c6d-b229-95dc1470231a
Best Regards
Elton Ji
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Similar Messages

Error: Your request could not be completed because a failure occurred while the report was being processed.

Post Author: sagimann
CA Forum: Deployment
Hello,
I'm not sure if this is due to bad deployment, but I suspect it is, at least due to bad environment.
My env is:
Solaris 10 64 bit
Oracle 10g client installed under /opt/oracle/app/oracle/product/10.2.0/client_1
BOXIR2 + FP2.6 installed under /opt/reporting, running under user 'bouser'. by the way, 'tnsping' works via that user.
Important bouser env:
ORACLE_HOME=/opt/oracle/app/oracle/product/10.2.0/client_1
TNS_ADMIN=$ORACLE_HOME/network/admin
LD_LIBRARY_PATH=$ORACLE_HOME/lib:$ORACLE_HOME/lib32
I reboot the box, then start BO like so:
cd /opt/reporting/bobje
. setup/env.sh
./mysqlstartup.sh
./startservers
./tomcatstartup
Then, I import a BIAR file with some reports, and whenever I try to open any report via infoview, I get a gray error message INSTEAD of the input param form:
Error:
Your request could not be completed because a failure occurred while the report was being processed. Please contact your system administrator.
This does not occur in our BOXIR2 on Windows, which is why I'm guess it's a deployment/env issue. The main obstacle I have is: how do I diagnose this? there's nothing in the bobje/logging folder, nothing in the /var/adm/message file except for the following line:
May 5 15:23:23 testbox1 boe_pagesd[3865]: [ID 253862 user.error] A failure occurred while the Page Server was processing report 'test report' (id=777) for user Administrator
pls advise,
thank you.

The solution is to turn off the printer preference (bottom of Page Setup screen) in the Crystal Report before uploading to the Server. Thanks to: http://pinchii.com/home/2011/12/error-adding-reports-to-crystal-reports-server/
The explanation, from a comment in the above linked blog post:
"To elaborate more on the error, what basically happens is that the Crystal Reports engine tries to get the status of the u201Creport printeru201D aka u201Cdefault printeru201D which was present on the system when the report was created, but the printer does not exist anymore. This causes the Crystal engine to error out. By setting the report to u201CNo Printeru201D, it tells the Crystal Engine not to look for that report printer when opening the report."
Edited by: abirdman on Feb 3, 2012 9:49 PM

Macbook Air 10.8.2 crashes after update. Gave a message "Some updates could not be performed due to an error"

3 of our mid 2012 Macbook Airs10.8.2 crash after update. Gave a message something like this "Some updates could not be performed due to an error" and now when rebooting I see panic...Unable to find driver for this platform...
I don't want to udate any more of these (I have 31) until I know what is causing this problem. Will I have to reimage these machines?

If you don't already have a current backup, back up all data, then reinstall the OS. You don't need to erase the startup volume, and you won't need the backup unless something goes wrong. If the system was upgraded from an older version of OS X, you may need the Apple ID and password you used to upgrade.
There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
If you installed the Java runtime distributed by Apple and still need it, you'll have to reinstall it. The same goes for Xcode.

Has anyone had the error "The file could not be read due to an error" when selecting ignore or replace image links. The linked images are in Dropbox if that helps.

I am working on a Mac 10.9.5 with Adobe CS6. My files are locally in Dropbox but once we moved files to network and tried opening the AI - the file would not recognize the original folder location. I tried ignoring the missing images but then I receive the error - The file could not be read due to an error." The same error happens when I try replacing the first missing image. I know the problem lies in the images are linked back to my Dropbox but the AI file doesn't care since it won't let me replace or ignore the image links.

Jasion,
Maybe a bit beside the question, but it is always recommended here to open/save from/to own hard disk, and to copy from/to networks and removable media. You may be lucky, at least for a while, but it is better to be safe than sorry.
In addition to the (far greater) risk of file corruption, some issues are mentioned here:
http://helpx.adobe.com/illustrator/kb/illustrator-support-networks-removable-media.html

Has anyone had the error "The file could not be read due to an error" when selecting ignore or replace? The linked images are in Dropbox if that helps.

I am working on a Mac 10.9.5 with Adobe CS6. My files are locally in Dropbox but once we moved files to network and tried opening the AI - the file would not recognize the original folder location. I tried ignoring the missing images but then I receive the error - The file could not be read due to an error." The same error happens when I try replacing the first missing image. I know the problem lies in the images are linked back to my Dropbox but the AI file doesn't care since it won't let me replace or ignore the image links.

Jasion,
Maybe a bit beside the question, but it is always recommended here to open/save from/to own hard disk, and to copy from/to networks and removable media. You may be lucky, at least for a while, but it is better to be safe than sorry.
In addition to the (far greater) risk of file corruption, some issues are mentioned here:
http://helpx.adobe.com/illustrator/kb/illustrator-support-networks-removable-media.html

"The file could not be read due to an error" Opens on one computer, displays this on another.

Hello,
I'm trying to troubleshoot several Illustrator files that won't open on desktops at my company's 2nd office. The files open fine on any desktop at my primary office. When opening the files from the 2nd office, it begins "Reading Illustrator file..." then the message "The file could not be read due to an error" is displayed and the file closes out.
Both offices have the same model desktop and are running:
Adobe Illustrator CS6 (up to date)
Windows 7 x64
Both desktops have the same system fonts and I've tried saving the files locally.
Thanks, Shaun

Hey Jacob and Monika,
Sorry if I wasn't clear, but I did already try saving the files to the hard disk.
"Both desktops have the same system fonts and I've tried saving the files locally."
My fix was copying the content of the files into new, blank .ai files. Those new files open from both offices now.
Still, I wish I could have identified the issue in case it happens again. The error message is vague and there isn't much info on the web about it.
Best, Shaun

Hi, I can't access my iTunes store even though I had updated to the latest version of the iOS. It always shows "the request could not be processed" when I tried to access the iTunes store. Pls help..

Hi, I can't access my iTunes store even though I had updated to the latest version of the iOS. It always shows "the request could not be processed" when I tried to access the iTunes store. This has been going on for the past 3 days already. Pls help..

Many thanks b Noir
This is a copy of ONEof the keys in the registry I changed as told by Apple support today. I also have changed others as instructed by GEAR software support to manually delete GEAR drivers (that I had installed but couldn't delete some of the others they mentioned from Windows system 32. Then some bright spark at work told me I need the Gear drivers so I downloaded the software and installed again.
Sorry, just this minute went to insert image and it is giving me a message saying this sort of content is not allowed?.
The most recent key I altered is in: HKey _local _machine. System\class - 4D36E965-E325-11CEBFC1-08002BE10318. Upper Filter data: Upper filter NTIDrvr SiRem GEARAspiWDN.
The GEARsoftware info about manually deleting GEAR drive is from:
http://www.gearsoftware.com/wiki/index.php?title=DRIVERS:_Windows_-_Updating%2C_ removing%2C_64_bit_versions%2C_etc
I hope you can help

The resource could not be saved due to unknown error

Hello,
After we installed the April 2015 CU on our Project 2010 farm, we have started to get the below error when we attempt to edit a Resource.
We did run the configuration wizard on both the app and WFE servers. Also, we are
not using any custom master page here.
So far below are the steps I have already tried and have not been successful.
Uncheck the 'Enable Dynamic content compression' and unchecked the 'Enable static content compression' as described in this
TechNet question. We did an IIS reset on all the App and WFE servers after making this change.
Confirmed that no services have stopped and that the service accounts have correct access level.
Everything else works in the PWA expect for this section. Has anyone else experienced this?
Thanks in advance for your response.

Hi Darogael,
Here is a similar thread which a bunch of advice. In particular try to edit and save the resource custom fields.
https://social.technet.microsoft.com/Forums/projectserver/en-US/638864dc-c085-4e93-b783-4dcea0f22f4e/edits-to-user-profiles-throwing-an-error-the-resource-could-not-be-saved-due-to-the-following
Hope this helps,
Guillaume Rouyre, MBA, MVP, P-Seller |

Hadoop ODBC linked server error: Specified driver could not be loaded due to system error 182

Hi,
I am trying to connect to a Hadoop server through a linked server in SQL Server. I downloaded and installed the Microsoft Hive ODBC driver - HiveODBC64.msi. But while I am trying to create the Linked server using this ODBC driver I am getting below error.
" Specified driver could not be loaded due to system error 182 (Microsoft Hive ODBC driver, D:\....\HiveODBC64.dll). (Microsoft SQL Server, Error: 7303)"
When I tested it locally and in another server, it is working properly. I am getting this error only in this server. looks like a dll error. But cannot identify where/what is the error. Could someone help me fix this issue.
Server info:
OS Name: Microsoft Windows Server 2008 R2 Enterprise Version 6.1.7601 Service Pack 1 Build 7601
SQL SERVER: Microsoft SQL Server 2008 R2(SP1)

Hi LinkedServer,
According to your description, you want to create linked server to connect to a Hadoop server in SQL Server, and you have created it successfully in the test server, the problem is that you get the issue in the production environment, right?
Based on the error message, as you said it seems that the issue is related to the HiveOBDC64.dll assembly. Since you have done it on the test server, you can copy and replace HiveODBC64.dll to production server in the C:\Program Files\Microsoft Hive ODBC
Driver\lib directory. Or you can reinstall the Microsoft Hive ODBC driver. Here is a blog which describe how to create a SQL Server Linked Server to HDInsight HIVE using Microsoft Hive ODBC Driver step by step, please refer to the link below to double check
if your steps are correct.
http://blogs.msdn.com/b/igorpag/archive/2013/11/12/how-to-create-a-sql-server-linked-server-to-hdinsight-hive-using-microsoft-hive-odbc-driver.aspx
Regards,
Charlie Liao
TechNet Community Support

HT201272 I attempted to copy an old playlist to an old iPod and was told that the items could not be copied until they were downloaded from the cloud. If I download the items so that I can copy them to my iPod are they they no longer in the cloud?

I attempted to copy an old playlist from my imac to an old ipod and was told that i must download the songs from the cloud before i can copy the playlist to the ipod. If i down load these songs from the cloud are they no longer available from the cloud for my other devices (iphone5)?

Try re-creating your iTunes library:
http://support.apple.com/kb/HT1451

Specified driver could not be loaded due to system error 127: The specified procedure could not be found. (...SQORA32.DLL).

I recently upgraded from 10g to 11g and upon this upgrade, a website of mine stopped working.
It is a classic ASP website. I added a "testdatabase" page to the website to test the basic functionality of opening a connection. I've pasted the testdatabase page below. Anyways, upon running this page, I get this error:
Specified driver could not be loaded due to system error 127: The specified procedure could not be found. (Oracle in OraClient11g_home1_32bit, D:\app\oracleadm\product\11.2.0\client_1\BIN\SQORA32.DLL).
I have two other environments where I have done the same upgrade and the site works just fine. I have compared all the IIS settings in my other environments to that of the one suffering from the error. Also, in the IIS settings, I have made sure that "Allow 32bit" was checked.
D:\app\oracleadm\product\11.2.0\client_1\BIN\SQORA32.DLL is actually where this DLL resides.
I have also checked to make sure the environment variables are correct.
The very first environment variable in the PATH setting is D:\app\oracleadm\product\11.2.0\client_1\bin; and there are no other references to oracle in the PATH environment variable.
I have done a google search and I've seen that people also tell me to check ORACLE_HOME to make sure it's correct. I've checked this in both of the working environments and there is nothing there. There is also nothing there in the broken environment. What should be there? If anything?
I don't know where else to look. What could be causing this error?
<%
Option Explicit
Response.Expires = 0
Response.Buffer = true
Dim conn
Err.Clear
On Error Resume Next
Set conn = Server.CreateObject("ADODB.Connection")
conn.Open "DSN=RPS11;UID=FFXQM;PWD=ffxqm6prd$"
If Err.Number <> 0 Then
Response.Write (Err.Description & "<br><br>")
Response.End
conn.Close
Set conn = Nothing
End If
conn.Close
Set conn = Nothing
On Error GoTo 0
%>

As a temporary solution, add the Administrators group to the IUSR and IWAM userids and see if that works. If it solves the problem, then it IS a matter of setting the users privledges correctly.

'file could not be written due to an error' when exporting jpg

I'm working with an Illustrator file in CS2 and after a certain point it has started saying 'the file could not be written due to an error' when exporting to a jpg.
i've tried a couple things like deleting layers and although the file is much smaller, it still says the same error when exporting.
at its highest it was 130mb as an illustrator file and jpgs were 2-5mb.
i''ve tried copying some of the layers into a new file but the error report still comes when i'm exporting.
i have vector and raster based data in the file and tried turning off/deleting either of the layers and there is no difference.
i don't understand why it's started doing this because before it had no problem at all exporting before.
ANY IDEAS ANYONE? I'm trying not to have to reproduce days of work to remake the file.
many thanks,
P

Mylenium,
Sounds like you know a good deal about this product. Is there any way to restore a color profile/setting to an earlier point?
I don't recall changing it and to tell you the truth, wouldn't be able to say which it may have been set to before - if different.
Thanks,
Paul

TS3694 trying to update software on my iphone 4s- "could not be updated due to unknown error" (6). what does this mean. my phone appears to be in a near complete state of update...

Not sure what to do. finally decided to upgrate software on my phone. installed itunes on my new laptop. plugged by phone in and started process. nearing the end i received an error message stating that the phone "could not be updated due to unknown error" (6). HELP!
the phone itself appears to be in mid update....

This describes error 6:
Errors related to third-party security software
Error 2, 4 (or -4), 6, 1000, and 9006
Follow the steps to troubleshoot security software. Often, uninstalling third-party security software will resolve these errors.
There may be third-party software that modifies your default packet size in Windows by inserting a TcpWindowSize entry into your registry. An incorrectly set default packet size can cause these errors. Contact the manufacturer of the software that installed the packet size modification for assistance or follow this article by Microsoft: How to reset Internet Protocol (TCP/IP).
Verify that access to ports 80 and 443 are allowed on your network.
Verify that communication to albert.apple.com or phobos.apple.com isn't blocked by a firewall or other Internet security setting.
Discard the .ipsw file, open iTunes and attempt to download the update again. See the steps under "Advanced steps > Rename, move, or delete the iOS software file (.ipsw)" below for file locations.
Restore your device while connected to a different network.
Restore using a different computer.

When I try to access GameCenter on my Mac it says "The requested operation could not be completed due to an error communicating with the server." How can I fix this?

When I try to access GameCenter on my Mac it says "The requested operation could not be completed due to an error communicating with the server." How can I fix this?

This usually caused by a customised hosts file.
These need to be the only entries in your /etc/hosts file:-
# Host Database
# localhost is used to configure the loopback interface
# when the system is booting. Do not change this entry.
127.0.0.1       localhost
255.255.255.255 broadcasthost
::1             localhost
fe80::1%lo0     localhost
Remove anything below these entries, then try and reconnect with GC. Once GC starts properly you can put the extra entries back in your hosts file, GC should start normally afterwards.
https://discussions.apple.com/message/19276629#19276629
Jerry

Hi, when I go to "select files to send" and click on "sent files" I get: "Internal Server Error (500) Your request could not be completed due to an internal server error". I tried rebooting and that didn't work. Any help would be appreciated. Thanks.

Hi, when I go to "select files to send" and click on "sent files" I get: "Internal Server Error (500) Your request could not be completed due to an internal server error". This never happened b4. I tried rebooting and that didn't work. Any help would be appreciated. Thanks.

Hi ,
Thank you for your question.
This error was caused by the incorrect site binding, I will give a reference of my test Lab. We add two A records in DNS which the FQDN of CAS and Mailbox could resolve IP address.;
Default Web Site:
Exchange Back End:
Then IIS must be restarted.
If there are any questions regarding this issue, please be free to let me know.
Best Regard,
Jim

Error - The request could not be performed due to an error from the I/O device

Similar Messages

Maybe you are looking for