Error when boot for install from CDs

Hi.
I have Solaris10 distribution on CDs and when I boot from CD and check type of install, I get a error:
WARNING: consconfig: could not find driver for screen device /pci@0,0/pci8086,24,4e@1e/pci8086,1879@c
Can't find driver for console framebufferI have motherboard: Intel Server Board SE7520JR2
Somebody, please, help me with my trouble :((

Have you tried re-transferring them from the computer where they are mounting?
You might try this, too:
Repairing the Hard Drive and Permissions
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger, Leopard or Snow Leopard.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer. Now restart normally.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.

Similar Messages

  • Error when booting off install disk: "panic: We are hanging here . . ."

    My iBook's working fine except it's very slow (3 years old), so I decided to reinstall the OS.
    When I try loading off my original OS X installation disk, it boots to an error "panic: We are hanging here . . ."
    If I stick the install CD into the iBook while it's on, it reads the CD fine and even offers to reboot off the CD for me. But when I reboot, I get the same panic error.
    When I take the CD out, the iBook loads fine again.
    So my computer still works, but I can't figure out a way to reinstall. Any ideas?
    fyi- I tried Disk Utility on my HD and it passed verification.

    Call Apple Support. They may be able to send you a replacement disc at nominal cost (much less than new). I think you'll need your computer's serial number so they can get the correct one.
    How does the computer handle other CDs? There's the slight possibility it is the drive and not the CD.
    The other thing to do is to try and troubleshoot why your computer is slowing down and at least not to have to immediately worry about getting a new CD. Here's a bunch of reading. However, I wouldn't blindly go running a bunch of utilities but to address things one by one. For example, one major slow down is an over-full hard drive and no utility will help with that.
    [Mac Tune-up: 34 Software Speedups|http://www.macworld.com/article/49489/2006/02/softwarespeed.html]
    [52 Ways to Speed Up OS X|http://www.imafish.co.uk/articles/post/articles/130/52-ways-to-speed-up-os-x>
    [Tuning Mac OS X Performance|http://www.thexlab.com/faqs/performance.html]
    [11 Ways to Optimize Your Mac's Performance|http://lowendmac.com/eubanks/07/0312.html]
    [The Top 7 Free Utilities To Maintain A Mac.|http://mac360.com/index.php/mac360/comments/thetop_7_free_utilities_to_maintain_amac>
    [Mac OS X: System maintenance|http://discussions.apple.com/thread.jspa?messageID=607640]
    [Macintosh OS X Routine Maintenance|http://www.macattorney.com/ts.html#Anchor-31774]
    [Kappy's Personal Suggestions for OS X Maintenance|http://discussions.apple.com/message.jspa?messageID=8230024#8230024 ]
    [a brody's Topic: Myths of required versus not required maintenance for Mac OS X|http://discussions.apple.com/thread.jspa?threadID=1772235]
    [Are the desktops cluttered with files and folders?|http://discussions.apple.com/thread.jspa?messageID=7668937#7668937]
    Message was edited by: Limnos
    Message was edited by: Limnos

  • Acpi:error when booting the install

    Hi guys,
    So I want to install Arch, but when I boot into the install USB I directly see the following error:
    ACPI: ERROR installing CMOS-RTC region handler
    I saw here that apparently it's a kernel bug since the 3.15.3 version. The latest download has the 3.15.7 version.
    First, I wanted to know if others came across this issue while installing.
    I also wondered if it's worth to install with an older kernel (if possible) or just wait for a fix..

    It doesn't block you from proceeding with install right?
    If so, that just ignore it and proceed with install.
    Your resulting installation will use most up-to-date kernel which is also "3.15.7-1-ARCH" (as of now) so that might indicate, that you might see this error also after installation.
    Nevertheless, it's a not a deal-breaker, and just without looking into it much deeper it doesn't sound critical (CMOS Real Time Clock, is indeed not critical piece of system), tough you might see some problems with RTC subsystem.
    Quickly skimming over the thread you linked, I don't see any relevant symptoms people are having there.  I see different errors in my journal during boot. Reported as errors, but to be understood as warnings.
    It's not so much beneficial to get over-excited about every red line in your journal, if there is not any documented real negative side-effects, usually this small issues tend to come and go, but it's always good to keep an eye on them.
    If it bothers you though, you can install with downgraded kernel (but I don't think this error justifies doing so).

  • Photoshop Error When Sending for Edit from Bridge or Lighroom

    When I attempt to send an image from Bridge CS5 or Lightroom using the Edit In or Open With commands Photoshop begins to launch but then displays the error message "Adobe Photoshop CS5 has encountered a problem and needs to close." If Photoshop is open and I attempt to open Bridge I get the same error message for Bridge.

    Thanks theFurryOne for your response.
    I do see my source in the data_source view.
    As for the Caused by:
    I see:
    Caused by:java.lang.NullPointerException
    at oracle.dbtools.raptor.navigator.net.DBURLStreamHandlerFactory.fetchSource(DBURLStreamHandlerFactory.java.213)
    ...............................................DBURLfileSystemHelper...
    at oracle.ide.net.URLFileSystem.createReader(URLFileSystem.java:1630)
    at oracle.ide.model.TextNode.createreader(TextNode.java:1680)
    .....................................loadTextBuffer...
    .....................................openImpl....
    ...48 more (these do not appear in the details window due to the number of exceptions prior to the caused by line)
    SQL Developer version
    .....About tab
    Version 2.1.1.64
    Build Main-64.45
    .....Version tab
    Java Platform 1.6.0_11
    Oracle IDE 2.1.1.64.45
    Versioning Support 2.1.1.64.45
    Edited by: amosgreg on Sep 2, 2010 4:58 AM

  • I installed windows 7 using Boot camp, Then i wanted to install the support software using boot camp and it always stops at 50% i tried installing the software using internet it always gives me error when i start installing it on windows, What to do?

    I installed windows 7 using Boot camp, Then i wanted to install the support software using boot camp and it always stops at 50% i tried installing the software using internet it always gives me error when i start installing it on windows, What to do?

    What is the error? Are you following the Bootcamp instructions? Where on the "internet" are you trying to install from? Did you try downloading from here http://www.apple.com/support/bootcamp/downloads/?

  • HT1222 I am getting an error when I am installing the new update for my iPhone. Is anyone else getting an error in the middle of installing?

    I am getting an error when trying to install the  current updates.

    Why don't you try telling us what the error is...
    Check this document for troubleshooting information: http://support.apple.com/kb/ts3694

  • "please use setup.exe for installati​on instead of blackberry desktop software.m​si" error when trying to install the software through 610_b038_m​ultilangua​ge.exe

    "please use setup.exe for installation instead of blackberry desktop software.msi" error when trying to install the software through 610_b038_multilanguage.exe
    I need to install this so that i can transfer my contacts and calendar to my laptop

    Hi and Welcome to the Community!
    Sorry to be dense, but what happens when you do exactly as the message instructs?
    Thanks!
    Occam's Razor nearly always applies when troubleshooting technology issues!
    If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
    Join our BBM Channels
    BSCF General Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

  • Any solution for 4280 error when using Itunes to burn CDs?

    Any solution for 4280 error when using Itunes to burn CDs?

    http://support.apple.com/kb/TA38101?viewlocale=en_US

  • Adobe error when booting

    Hi
    My MacBook Pro running Mountain Lion is logging the following Adobe error when booting. I don't know which program from Adobe it comes from. I have Flash and Photoshop installed.
    It takes my Mac 11 seconds of boot time to generate this error every time I boot. I would like to get rid of the program causing it.
    Frank
    My log:
    26/09/12 07.27.16,000 kernel[0]: CODE SIGNING: cs_invalid_page(0x1000): p=264[ksadmin] clearing CS_VALID
    26/09/12 07.27.27,665 osascript[276]: Error loading /Library/ScriptingAdditions/Adobe Unit Types.osax/Contents/MacOS/Adobe Unit Types:  dlopen(/Library/ScriptingAdditions/Adobe Unit Types.osax/Contents/MacOS/Adobe Unit Types, 262): no suitable image found.  Did find:
              /Library/ScriptingAdditions/Adobe Unit Types.osax/Contents/MacOS/Adobe Unit Types: no matching architecture in universal wrapper
    26/09/12 07.27.44,484 osascript[280]: Error loading /Library/ScriptingAdditions/Adobe Unit Types.osax/Contents/MacOS/Adobe Unit Types:  dlopen(/Library/ScriptingAdditions/Adobe Unit Types.osax/Contents/MacOS/Adobe Unit Types, 262): no suitable image found.  Did find:
              /Library/ScriptingAdditions/Adobe Unit Types.osax/Contents/MacOS/Adobe Unit Types: no matching architecture in universal wrapper
    26/09/12 07.27.46,308 osascript[281]: Error loading /Library/ScriptingAdditions/Adobe Unit Types.osax/Contents/MacOS/Adobe Unit Types:  dlopen(/Library/ScriptingAdditions/Adobe Unit Types.osax/Contents/MacOS/Adobe Unit Types, 262): no suitable image found.  Did find:
              /Library/ScriptingAdditions/Adobe Unit Types.osax/Contents/MacOS/Adobe Unit Types: no matching architecture in universal wrapper
    26/09/12 07.27.46,401 osascript[282]: Error loading /Library/ScriptingAdditions/Adobe Unit Types.osax/Contents/MacOS/Adobe Unit Types:  dlopen(/Library/ScriptingAdditions/Adobe Unit Types.osax/Contents/MacOS/Adobe Unit Types, 262): no suitable image found.  Did find:
              /Library/ScriptingAdditions/Adobe Unit Types.osax/Contents/MacOS/Adobe Unit Types: no matching architecture in universal wrapper
    26/09/12 07.27.46,753 osascript[283]: Error loading /Library/ScriptingAdditions/Adobe Unit Types.osax/Contents/MacOS/Adobe Unit Types:  dlopen(/Library/ScriptingAdditions/Adobe Unit Types.osax/Contents/MacOS/Adobe Unit Types, 262): no suitable image found.  Did find:
              /Library/ScriptingAdditions/Adobe Unit Types.osax/Contents/MacOS/Adobe Unit Types: no matching architecture in universal wrapper
    26/09/12 07.27.46,890 genatsdb[251]: *GENATSDB* FontObjects generated = 737
    26/09/12 07.27.46,927 osascript[284]: Error loading /Library/ScriptingAdditions/Adobe Unit Types.osax/Contents/MacOS/Adobe Unit Types:  dlopen(/Library/ScriptingAdditions/Adobe Unit Types.osax/Contents/MacOS/Adobe Unit Types, 262): no suitable image found.  Did find:
              /Library/ScriptingAdditions/Adobe Unit Types.osax/Contents/MacOS/Adobe Unit Types: no matching architecture in universal wrapper
    26/09/12 07.27.46,983 osascript[285]: Error loading /Library/ScriptingAdditions/Adobe Unit Types.osax/Contents/MacOS/Adobe Unit Types:  dlopen(/Library/ScriptingAdditions/Adobe Unit Types.osax/Contents/MacOS/Adobe Unit Types, 262): no suitable image found.  Did find:
              /Library/ScriptingAdditions/Adobe Unit Types.osax/Contents/MacOS/Adobe Unit Types: no matching architecture in universal wrapper

    First, in System Preferences -> Users & Groups -> Login items, look for anything Adobe in the list of items and remove it. Then your Mac will not attempt to load anything Adobe during boot-up or log-in anymore, but boot much faster again.
    Then see if problems persist when starting your Adobe apps. If so, uninstall them completely (!!! - usually, there are files left over under Applications and in Application Support in the Libraries - remove those manually), then re-install these apps fresh.

  • Newbie apex error when trying to install the OEHR Sample object.

    ORA-01653: unable to extend table FLOWS_030000.WWV_FLOW_ONLINE_HELP by 8 in tablespace APEX
    I got this error when trying to install.
    I will go back now and check the storage space.
    I could not find any error message on it.
    Thanks.Steve

    Just few minutes after asking this question on forum, I was able to find the workaround for opening the DashboardDesigner.exe.
    What I was trying earlier was that, In my "Business Intelligence Center" site,  i was trying to open the Dashboard Designer from "PerformancePoint Content" list by clicking "New Item" from "Items" tab in Ribbon.
    Instead Now I go to the connections library "Data Connections",  Go to "Documents" tab in Ribbon and then click on "New Document".
    Voila!
    Finally "DashboardDesinger.exe" opens up! :D
    Now from this designer application, I can add other Lists directly and can add "PerformancePoint Content" list for creating actual ScoreCards, Dashboards, KPIs etc.
    Happy Learning!
    Shri07

  • Error when updating the data from DSO to cube

    Hi,
    I am getting the error when uploading the data from the ods to cube.
    The following is the error message.
    Unable to determine period for date 20090101, fiscal year variant Z2: Error #
    How can i solve this issue.
    Regards
    Annie

    Hi ,
    fiscal year variant, go into Customizing for Financial Accounting (FI) under Financial Accounting Global Settings >>>Fiscal Year >>>Maintain Fiscal Year Variant.
    check this link ..
    http://help.sap.com/saphelp_scm41/helpdata/en/50/0d89f2ad919c40b95b9ae7583c8c96/frameset.htm
    http://help.sap.com/saphelp_scm41/helpdata/en/50/0d89f2ad919c40b95b9ae7583c8c96/content.htm
    Regards,
    shikha

  • Error when determining  a number from object BI_ODS

    Error When determining a number from object BI_ODS and number 01  when flat file source system is assigned to transfer rules of infosource , when activating this error occured .
    plz need solution.

    Hi,
    Number ranges can be maintained through the transaction SNRO. For details check:
    http://help.sap.com/saphelp_nw70/helpdata/EN/2a/fa02e3493111d182b70000e829fbfe/frameset.htm
    Rgds-
    Sonal

  • Error when determining a number from object BI_TSDTEL and number 01

    Hi BW Experts,
    After Transporting Infosources (Master & Transaction) to BW QA, the transfer rules were not getting activated in QA. The following error message was diaplyed.
    "Error when determining a number from object BI_TSDTEL and number 01
    Object name can only contain characters from syntactical character set
    Object name can only contain characters from syntactical character set
    Data element for InfoObject KOKRS 0CO_AREA could not be created
    Data element for InfoObject KOKRS 0CO_AREA could not be created
    Transfer structure 0IM_FA_IQ_2_SB activated under the name 0IM_FA_IQ_2_SA
    It is not necessary to copy dependent objects for transfer structure 0IM_FA_IQ_2_SA
    Transfer structure 0IM_FA_IQ_2_SA does not exist
    Error RSAR 440 when handling objects with type R3TR ISTS."
    I have gone through the Note: 674818.
    Could someone clear me about BI_TSDTEl, By using this do we need to maintain object intervals manually in all the systems like BW ( Dev & QA ), R/3 (Dev & QA).
    Because  I have not seen the Intervals in R/3 ( Dev & QA) systems.
    please could someone provide Inputs for this.
    Thanks in Advance
    Regards
    SK

    Hi,
    Try to see that transfer structure is existing in the sytem which is connecting in
    the BW quality.
    You need the same to be transported from the development server of R/3 to quality server of R/3.
    Just check if this helps.
    Regards
    Rahul Bindroo

  • Short dump error when extracting delta records from R/3

    I am working on BW 3.5 and I am facing some short dump error when extracting delta records from the r/3 to BW.
    Below is the error message
    Kindly do the needful ASAP.
    Job started
    Step 001 started (program SBIE0001, variant &0000000024277, user ID BWREMOTE)
    Asynchronous transmission of info IDoc 2 in task 0001 (0 parallel tasks)
    DATASOURCE = 0ISCM_PAYMENT_01
             Current Values for Selected Profile Parameters               *
    abap/heap_area_nondia......... 2000000000                              *
    abap/heap_area_total.......... 2000000000                              *
    abap/heaplimit................ 40000000                                *
    zcsa/installed_languages...... DE                                      *
    zcsa/system_language.......... E                                       *
    ztta/max_memreq_MB............ 2047                                    *
    ztta/roll_area................ 6500000                                 *
    ztta/roll_extension........... 2000000000                              *
    2,454 LUWs confirmed and 2,454 LUWs to be deleted with function module RSC2_QOUT_CONFIRM_DAT
    ABAP/4 processor: MESSAGE_TYPE_X
    Job cancelled

    Hi,
    I look at the transaction ST22 to see which type of error has given you. Take a look at the notes to correct the error.
    Another option is to look at OSS notes, because the error is giving you a standard extractor.
    Greetings,

  • I have a A12E6 error when downloading and installing apps

    I have an
    A12e6 error when downloading and installing apps   yesterday i had the A12e1 error so i used the cleaner tool and did a new install but today again i have an arror A12e6
    Do you have a solution for me???? (mac osx 10.7.5)
    kind regards Arold

    Hi Arold,
    Welcome To The Forums
    http://forums.adobe.com/thread/1197816 or http://forums.adobe.com/thread/1291134 may help,
    Thanks!
    Eshant

Maybe you are looking for

  • How do I  connect MacBook Pro without mini-display port to my HDMI TV?

    I have a MacBook Pro computer purchased around 2008. I want to connect it to my Panasonic HDMI TV; however, this MacBook Pro doesn't have a mini-display port. Is there a work around? I would like audio & video. Thanks so much in advance for any help.

  • How bad can a company be?

    I called BT around mid May. I informed them i was going to move to a new flat in NW2 in June. I told them the flat is being completely renovated and that i wanted to get a phone line. The BT employee on the phone did some checks and confirmed to me t

  • Where's the Denim update?

    Where's the Denim update? I'm in the US and have a Lumia Icon. It's the middle of March and I still don't have it. I got an update just last night for the "extras + info" app in the Windows Store, and now it *says* I'm on Denim...but I haven't had an

  • Can I jump to a specific time in a slide?

    Hello everybody, I'm pretty new to the Adobe Captivate Project and although it works very intuitive and there are a lot of resources available, I couldn't find the answer to my question. I'm making an instruction video/software simulation for clients

  • Random Number in the Transformation File

    Hi All, I need to send a random number while mapping from one xsd to other in the xsl file . The random number should be alpha numeric with 5 chartacters. I tried using generate-guid() but it generates 32 characters. How do u i shrink this to 5 chara