Error when run Depreciation Posting Run AFAB
Hi,
I found error when run Depreciation Posting Run for period 7 2007.
FYI. I had run Unplanned Depreciation (TCode: ABAA) with document date 31.10.2007 and posting date 31.10.2007, trans. type 640. After that, i want to run Depreciation Posting Run (TCode: AFAB) with fiscal year: 2008, posting period: 7, reason for posting run: repeat. Select on Test Run. Then i found error message as below.
Error Message:
Documents manually posted within dep.doc.number range
Message no. AA728
Diagnosis
In the number range interval for the document type for posting depreciation, a document has been posted which was not created within the framework of depreciation posting. The last document posted by depreciation posting was assigned the number .
Procedure
Contact your Systems Specialist. When changing the number range interval for the document type in depreciation posting, you have to specify a new interval in which no documents exist. Using organizational measures, you can guarantee that there are no documents apart from those created by depreciation posting in this number range.
Can any one help how to solve this issue?
Hi Paul,
Now I go to TCode: FBN1 - Accounting Document Number Ranges, then i want to change the range for year 2008.
No Year From No To No Current No Ext
03 2001 0300000000 0399999999 - /
03 2002 0300000000 0399999999 - /
03 2003 0300000000 0399999999 - /
03 2004 0300000000 0399999999 - /
03 2005 0300000000 0399999999 - /
03 2006 0300000000 0399999999 - /
03 2007 0300000000 0399999999 - /
03 2008 0300000000 0399999999 - /
03 2009 0300000000 0399999999 - /
Referring back to Asset Accounting, the Reference Document: 19.
Do it mean that my FI doc. no is 0300000019 ? I bit confuse on this..
Can you guide me more details on it?
Thanks in advance.
Edited by: Nur Aman Abdul Manap on Apr 15, 2009 2:09 AM
Similar Messages
-
How to solve error when run Depreciation (T-Code:AFAB)
Dear All Experts,
Hi,
I found error when run Depreciation for period 9 FYI. I had run Planed posting period Depreciation (TCode: AFAB). with fiscal year: 2010, posting period: 9, reason for posting run: Planed posting run. Select on Test Run. Then i found error message as below.
Documents manually posted within dep.doc.number range
Message no. AA728
Diagnosis
In the number range interval for the document type for posting
depreciation, a document has been posted which was not created within
the framework of depreciation posting. The last document posted by
depreciation posting was assigned the number .
Procedure
Contact your Systems Specialist. When changing the number range interval
for the document type in depreciation posting, you have to specify a new
interval in which no documents exist. Using organizational measures, you
can guarantee that there are no documents apart from those created by
depreciation posting in this number range.
Would you help me how to solve this error?
Thank you in advance
Best Regards
Utarat.PHi Utarat,
first question is: have you really manually posted a Documents within dep.doc.number range
If you post with RABUCH00, note 193984 could be relevant for you.
Check if the intervall in Table TABA don't fits with the Intervall in BKPF.
Example:
TABA
MANDT BUKRS AFBLGJ AFBLPE AFBANZ BLNRF BLNRT XBUKZ
100 XXXX 2010 004 01 4200000013 4200000016 X
100 XXXX 2010 005 01 4200000017 4200000020 X
100 XXXX 2010 006 01 4200000021 4200000024
On the other Hand In Table BKPF (or Tr. FB03) you can see that 4200000037 already
exits.
BUKRS BELNR GJAHR BLART BUDAT CPUDT CPUTM TCODE
XXXX 4200000024 2010 YY 30.06.2010 06.07.2010 19:36:30 ABF1
XXXX 4200000037 2010 YY 30.06.2010 06.07.2010 19:37:47 ABF1
Regards Bernhard -
AFAB - Depreciation Posting Run Error
When I tried to execute the Depreciation Posting Run, I get the error message "Internal error with background job scheduling RAPOST2000"
Hv anyone face this problem before? Pls help!
Thanks.Thanks~ I checked with my colleague, he told me that the user is lost few objects in the role. This included the User Authority and the program objects.
After he added the objects to the user's role. The issue is settle.
Thanks~! -
Error Depreciation Posting Run
Dear All,
I have a trouble about depreciation posting run, there is an error message when I tried AFAB.
Right now, I already maintain the validation (OKC7) in order to change the error [E] message become warning only [W], so atleast the depreciation could be posted (depreciation can be posted, althought there is still error on it).
The trouble already occured for 2 periods (Apr-May), and I've just found the error---there was incorrect posting for the asset class.
Should I use F-92 (asset retire), ABAON, or there is any other solution for this?
Please advise...
Thanks & regards,
Vandahi,
try transaction <b>afar</b>
(read the documentation of tht report RAAFAR00)
A. -
Depreciation posting run ( afab)
Dear All,
While Depreciation posting run using tran. code ( afab ) i.e SAP Standard transaction,
to execute in foreground Following message appear .
! This processing can only be carried out as background processing !!
If I run in background program run successfully.
It is possible to run the program in forground.
Previous SAP version ECC 5.0 this program was run foreground also.
Please reply me any solution for the same.
Reagrds,
SantoshWhen we run the program in Background following Error obseved in some documents.
NOT POSTED 2 3000 SKGE 23602 ERROR00001 Ordinary deprec. 451,317.00- 0.00 -451,317.00 451,317.00- INR
NOT POSTED 3 5000 HOGE 11402 ERROR00001 Ordinary deprec. 361,699.00- 0.00 -361,699.00 361,699.00- INR
Now Please suggest How to rectify this Error.
But in SAP 4.6 , Program run in foreground and we will get the Exact Error message and system response as to How the Error can be corrected.
In Background with Spool nothing has to be done.
Regards,
Santosh -
Depreciation Posting Run Error
i'm trying to run depreciation posting for company code X from AFAB. but during test run i got the following error message;
"Field Bus. Area is a required field for G/L account MEYA 2572530000"
however all asset's "field area" are filled by a value. what may cause this problem.
thank you for your helphi,
pls make business area as a optional in the field status variant by using t.code obc4
Thanks
phaneendra -
Posting period of "Depreciation Posting Run" problem
Hi all,
I was configured my company code with 12 period of nomal fiscal year (defauld fiscal year variant K4). I think Posting period field of Depreciation Posting Run screen (T-code: AFAB) must have 12 posible entries, are 1,2,3,...,11,12. But when I display posible entries of this filed, it only have to posible entries (000-000, 000-365). So that, I can't choose a period to excute real depreciation run.
How to define posible entries 1,2,3,..,11,12 of posting period field of Depreciation posting run screen?
ChinhvhHi,
If I have understood your question correctly
When u do F4 in field "Posting Period" in AFAB you get the following screen:
From To
000 000
000 365
You don't do F4 in that field. Since your Posting Period Variant is K4, just manual input the relevant posting period in the field. i.e if you want to post depreciation for April then just input Period 4 in the field.
Now what you have to be careful is which depreciation method you are going to select for doing the Posing Run. (i.e the Reason for Posting Run fields)
You have 4 methods which is described below:
1. Planned Posting Run. (This should be done if all the depreciation upto the earlier posting period has been done properly under the planned posting run).
If you have done unplanned run for earlier periods and have never done a planned posting run for the earlier periods for the concerned asset, then you cannot do planned posting run for period 4 directly. You should first do planned posting for period 1, then for period 2, then for period 3, and then finally for period 4. The depreciation will be zero for Posting periods 1,2,3 if your start depn in your asset master is 1st April.
2. Repeat Run: You can use this to do repeat run. You can do Planned depreciation run only once for a particular asset for a particular period. You can then do a repeat run for doing the depreciation run for the same asset.
3.I don't think you wll need to do Restart run.
4. You can do unplanned depreciation run directly for period 4, if you have not done the depreciation run for the particular asset for the earlier period. but this is not recommended. This should be done only in specific circumstances when you have no chance of doing either planned depn run or repeat run.
Pl assign points.
Rgds
PRasad -
Travel Expense - Posting run error - Error during creation of posting run
Hi Guru's,
Look forward for your insights. Here you go with my question.
We are implementing Expense Mgt with Portal with out scope for payroll in SAP. I have set up Expense type, WT, Symbolic A/c to G/L Accounts. Im performing Unit testing currently.
Created Expense trip in ESS, from R/3 tcode PRAP, have approved trip, and settled through Tcode - PREC.
When I try to create posting run under transfer to accounting, I get following error
Error during creation of posting run number (->PR1
Message no. 56840
I'm not sure why this error was popping up. Appreciate your suggestion.
Regards
Praveen.NHi,
Since you are trying to make payment through FI, you need to maintain ur employee as Vendor. You can do it through PRAA.
So while creating posting run for this trip, it checks if the respective Vendor for this employee is maintained or not.
Pls maintain it as vendor and see if the errors are still coming.
Rakesh -
Distribution Cycle KSV5 Resulting in error when deselected the test run chk
Hi Experts,
Please help me out
iam getting an error while running a Distribution Cycle KSV5 Resulting in error when deselected the test run chk box.
When run the same in the test run, there isn't any error log. but when i deselect the same & run iam getting an error like
First Message:
Balance per segment 9999 is not zero
Message no. FAGL_COFI025
Diagnosis
Balance per segment 9999 is not zero.
The balance on segment 9999 is 50.00 (transaction currency), 0.00 (object currency), and 50.00 (controlling area currency).
System Response
With the standard settings, postings cannot be made to the document because the balance for segment and partner segment does not amount to zero. This may be due to a programming error, or this setting may have been made (perhaps unintentionally) in the BAdIs for determining the segment or partner segment.
Procedure
If there is a programming error, please inform your system administrator.
If this behavior is intentional, you can deactivate error message FAGL_COFI 025 in Customizing or change the error message into a warning message or an information message.
2nd Message
Balance per segment 1000 is not zero
Message no. FAGL_COFI025
Diagnosis
Balance per segment 1000 is not zero.
The balance on segment 1000 is 50.00- (transaction currency), 0.00 (object currency), and 50.00- (controlling area currency).
System Response
With the standard settings, postings cannot be made to the document because the balance for segment and partner segment does not amount to zero. This may be due to a programming error, or this setting may have been made (perhaps unintentionally) in the BAdIs for determining the segment or partner segment.
Procedure
If there is a programming error, please inform your system administrator.
If this behavior is intentional, you can deactivate error message FAGL_COFI 025 in Customizing or change the error message into a warning message or an information message.
3rd Message
No update performed due to an error
Message no. GA719
Diagnosis
A serious error occurred during processing.
System Response
Processing is continued as far as possible, but results are not posted.
Procedure
This error is shown in the error list before this error message. Here you can find more information about this particular error.
I would appreciate an early reply........!!!
Thanks & Regards,
NeelaHi,
Check notes 764652 and 897086; it might be helpful.
Regards,
Eli -
Spectrum digital DSK5416 driver setup gives an error when test wizard is run.
Please help us with the following problem we are facing:
1. Spectrum digital DSK5416 driver setup gives an
error when test wizard is run. A snap shot of the same has been
attached.
2. The A/D module doesn’t pickup microphone signal or
an audio sample for loopback but the implementation of the same works
fine in CCS environment. (We are using Mic In and Speaker Out lines)
3. When a real-time application has run successfully
and if you close the VAB environment the application starts running
automatically until you reset the board.
4. We don’t find the flash program button enabled, so
that any real-time program can be burned into flash and demonstrate the
embedded feature.
Note:
We are using Windows Xp professional edition.
Program is developed using DSK5416Hello, I have included some information that will help address your questions: (1) I couldn't see the attached image file (contained errors). The RIDE/VAB DSK5416 Driver makes use of a JTAG communication when reading/writing memory on the DSK5416 hardware. You will need to make sure that the JTAG transfer option has been selected in the Driver Setup dialog box. The memory test process may seem to take a long time due to the amount of memory being accessed. (2) The VAB RTDSKAD block component provides a one-channel A/D input that makes use of the line-in channel on the DSK5416 hardware. (3) VAB does not remove the downloaded DSP executable program from DSK5416 memory, and it does remain resident. That being said, I wouldn't expect that the program would begin execution when VAB is closed. I would recommend that you verify that the DSP program stopped properly upon selecting the VAB Stop command. Then, close VAB as normal. (4) The RIDE/VAB driver for the DSK5416 does not support programming of flash memory on the DSK5416 hardware. Regards, Steve
-
Error when I try to run a Journal report, Works fine in previous month
Hi,
I am getting an error when I try to run a Journal report in HFM. The report runs fine for October Month but fials in November. does anyone have any ideas what it could be. The error message details are per below
Error Reference Number: {B6DCF307-AB72-476F-9634-70E35C3E8F2F};User Name: vivek.singha@WorleyParsons
Num: 0x8004023b;Type: 0;DTime: 12/20/2010 7:42:24 PM;Svr: AUHODWRLYP9;File: CHsvDSCalcStatus.cpp;Line: 391;Ver: 9.3.1.6.2558;
Num: 0x8004023b;Type: 0;DTime: 12/20/2010 7:42:24 PM;Svr: AUHODWRLYP9;File: CHsvDSCalcStatus.cpp;Line: 7035;Ver: 9.3.1.6.2558;
Num: 0x8004023b;Type: 0;DTime: 12/20/2010 7:42:24 PM;Svr: AUHODWRLYP9;File: DataSecurity.cpp;Line: 696;Ver: 9.3.1.0.2042;
Num: 0x8004023b;Type: 0;DTime: 12/20/2010 7:42:24 PM;Svr: AUHODWRLYP9;File: DataSecurity.cpp;Line: 329;Ver: 9.3.1.0.2042;
Num: 0x8004023b;Type: 0;DTime: 12/20/2010 7:42:24 PM;Svr: AUHODWRLYP9;File: SecurityInternal.cpp;Line: 1695;Ver: 9.3.1.0.2042;
Num: 0x8004023b;Type: 0;DTime: 12/20/2010 7:42:24 PM;Svr: AUHODWRLYP9;File: CHsvJournals.cpp;Line: 1249;Ver: 9.3.1.0.2042;
Num: 0x8004023b;Type: 0;DTime: 12/20/2010 7:42:24 PM;Svr: AUHODWRLYP9;File: CHsvJournals.cpp;Line: 988;Ver: 9.3.1.0.2042;
Num: 0x8004023b;Type: 0;DTime: 12/20/2010 7:42:24 PM;Svr: AUHODWRLYP9;File: CHsvJournalsACM.cpp;Line: 1734;Ver: 9.3.1.0.1502;
Num: 0x8004023b;Type: 0;DTime: 12/20/2010 7:42:24 PM;Svr: AUHODWRLYP9;File: CHsvJournalsACM.cpp;Line: 1648;Ver: 9.3.1.0.1502;
Num: 0x8004023b;Type: 0;DTime: 12/20/2010 7:42:24 PM;Svr: AUHODWRLYP9;File: ReportGenerator_Journal.cpp;Line: 136;Ver: 9.3.1.0.2176;
Num: 0x8004023b;Type: 0;DTime: 12/20/2010 7:42:24 PM;Svr: AUHODWRLYP9;File: CHsvReportGeneratorACM.cpp;Line: 575;Ver: 9.3.1.0.2176;
Num: 0x8004023b;Type: 0;DTime: 12/20/2010 7:42:24 PM;Svr: AUHODWRLYP9;File: HFMActionsExecution.cpp;Line: 2189;Ver: 9.3.1.0.2385;
Num: 0x8004023b;Type: 0;DTime: 12/20/2010 7:42:24 PM;Svr: AUHODWRLYP9;File: HFMActions.cpp;Line: 72;Ver: 9.3.1.0.2385;
Num: 0x8004023b;Type: 0;DTime: 12/20/2010 7:42:24 PM;Svr: AUHODWRLYP9;File: HFMCESAction.cpp;Line: 28;Ver: 9.3.1.0.2385;
Num: 0x8004023b;Type: 0;DTime: 12/20/2010 7:42:25 PM;Svr: AUHODWRLYP9;File: Actions.cpp;Line: 291;Ver: 9.3.1.0.2385;
Regards
VivekHi All,
I narrowed it down by running a report excluding working journals and that worked fine.
This was being caused by an invalid working Journal. I exported all journals from Prod, and tried loading them to test. One of the errors was
"Line: 7736, Error: Invalid parent.child entity dimension specified"
Looking at the row the journal did not have an entity specified for one of the lines.
When a valid entity was specified the journal report then starts working.
Lesson. Check all journals are valid. To find error, load journals export in a different environment.
Thanks all for your help.
Regards
Vivek -
Error when I try to run a form
Hi,
I created a table-based form, but I get a error when I try to run it (CTRL+R):
java.lang.ClassNotFoundException: oracle.forms.engine.Main
How can I fix it?
Thanks
Savio BarrosIf you have JInitiator installed successfully that is if you are able to run the test form try this
Open the control panel of your JInitiator (double click on the JInitiator icon in windows control panel) in the Proxies tab, see if you have the Use Browser Settings check box checked.
Otherwise configure the proxy settings and test your form.
Regards,
Tony -
Question about Depreciation Posting Run
I Gurus:
I have a question about Depreciation Posting Run; I want to block two active assets for not entry in the Depreciation Posting Run and don´t affected it.
I try to blocked the fixed asset in AS06 transaction but de active asset is affected in Depreciation Posting Run.
Could you please help me??
Thanks a lotHi,
To my limited knowledge, one can deactivate the assets after transfering the value from the to be deactivated asset.
As per the generally accepted accounting principles, assets with value should have an impact in our financial statment. In SAP, deactivating assets means, wrongly created assets which will not have any value and will not have impact any of your financial books of accounts.
I think, you are looking for a functionality, where you do not want to depreciate the assets (ex. Land). If it is so, you can give the Zero percentage by creating a new dep. key if you are using depreciation key based calculation of depreciation.
Hope it clears your doubt,
Regards
A.Saravanan. -
Error AAPO191 in AFAB: depreciation posting run
Hi,
I created a new depreciation area and customized the account determination on AO90. When running the AFAB (dep. posting run) the system issues the error AAPO 191 "Internal error in item 0000000000: asset row is not complete"
I checked the note 859617 which says the accumulated depreciation account must not be set as fixed asset reconciliation account.
As far as I know, these accounts have to be set as reconciliation accounts otherwise it will be open for manual postings leading to inconsistencies between FI-AA and FI-GL.
I checked transaction OAMK and it has some accounts in it (but not the ones with errors). Nevertheless, it has no option to include new accounts.
Can anyone help me out with this error?
Thanks in advance,
Paulo SiqueiraHi Paulo,
this error is nearly always about wrong or missing account control in your account determination. Please check closely
note 7595 and verify if any account has been erroneously defined or is missing.
As per note 7595:
1. Areas to be posted in dialog > T093-BUHBKT = 1
The balance sheet accounts and the accumulated depreciation accounts must be characterized as reconciliation accounts of account type 'A'. Down payment account KTANZA must also be a reconciliation
2. Areas to be posted periodically or areas only relevant to depreciation -> T093-BUHBKT = 2
Create the accounts of these areas as ordinary G/L accounts. They may not be reconciliation accounts.
Regards Bernhard -
Error during repeat run depreciation via tcode AFAB
hi,
I have removed year-end closing for assets to year 1999 via tcode OAAQ . However, once i want to run repeat depreciation via tcode AFAB, I received error messages as follows:-
1. Field Cost Ctr is a required field for G/L account 4300000
2. Account 'Expense account for ordinary depreciation' could not be found.
Appreciate your advise to solve the errors.
Thanks a lot!Dear Mohd.,
PLease check the following in ur configuration:
1) You must have CO implemented. That is why when u run, AFAB system posts its depreciation in cost center mentioned in asset master. Now do one thing, take out the list of assets where cost center is not attached. Take out this info from ANLZ table.
2) Go to AO90 & check the account assignment to all the account determinations.
Try executing after this. It will work.
Regards,
Ajay
Maybe you are looking for
-
I tried to install Mavericks but shortly after the installation initialized I got a message saying that I didn't have enough space to complete the install. It asked to free up just under 1 MB of space...but I cannot get access to my hard drive. Whe
-
Why can't I create Fillable PDF Forms using Adobe Acrobat X Pro and upload to Dreamweaver?
I can create fillable PDF Forms using Adobe Acrobat X Pro. I can email them to someone using Adobe Reader (free) and they can fill them, save and email to me. But when I upload the form to Dreamweaver CS5, the form is not fillable. And yes, I saved i
-
Adobe device central cs5 has stopped working
I am using cs5 on windows 7. When I tried to browse for new devices using Browse Devices, the progress window displayed "processing 0 from 587" and then the window with the above title popped up and just prompted me to close the program. I noticed th
-
JPEG export preferences problems
Hi. I have indesig cs5.5 and tryed set export resolution and jpeg color space. But in my computer i can't because this properties don't existe. In other computer this script read ok. below the JPEG export preferences properties. The script tell appli
-
Once more on how to organize in Aperture
How would you have organized the 100 photos I have of my family with three children and each has their children? I did: Folder FAMILY 100 Project Jeff 35 Album Charlie 12 Album Eli 12 Album Cate 11 Project Deb