Error when trying to connect to identity server from vcac 6 server during fresh install attempt

     Hello.  I am trying to install vcac6 so I can try it out but I am getting the error "Command execution failed with unexpected error: java.security.cert.CertificateNotYetValidException" when I try to point the vcac appliance at the identity appliance during the sso config.  I researched around but didn't find anything.  I confirmed that all network communication is good between the two.  Dns names resolve fine.  I am using self generated certs for both.
Thanks in advance for any help you can give!

As poorem suggested, I would check that the time is the same on both the identity and vcac appliances.  It has been a while since I posted this question but I believe that did get me past that specfic error.  I changed the timezone on each and made sure the times were correct and the same.

Similar Messages

  • RMI Error when trying to connect to remote server

    We are getting an RMI error (below) when trying to connect to a remote weblogic 9 server with mission control.
    We are running a portal application on the app server. If we connect using mission control before the app starts then mission control connects successfully.
    If we wait until the portal application is running then we get the following error when we try to connect:
    Could not open Management Console for UAT Live (1).
    java.rmi.UnmarshalException: error unmarshalling return; nested exception is:
         java.lang.ClassNotFoundException: com.vignette.monitor.framework.VgnMBeanInfo (no security manager: RMI class loader disabled)
    java.rmi.UnmarshalException: error unmarshalling return; nested exception is:
         java.lang.ClassNotFoundException: com.vignette.monitor.framework.VgnMBeanInfo (no security manager: RMI class loader disabled)
         at sun.rmi.server.UnicastRef.invoke(UnicastRef.java:162)
         at com.sun.jmx.remote.internal.PRef.invoke(Unknown Source)
         at javax.management.remote.rmi.RMIConnectionImpl_Stub.getMBeanInfo(Unknown Source)
         at javax.management.remote.rmi.RMIConnector$RemoteMBeanServerConnection.getMBeanInfo(RMIConnector.java:1031)
         at com.jrockit.console.rjmx.RJMXConnection.getMBeanInfos(RJMXConnection.java:262)
         at com.jrockit.console.rjmx.RJMXConnection.getMBeanInfos(RJMXConnection.java:297)
         at com.jrockit.console.rjmx.RJMXConnectorModel.initializeAttributeInfos(RJMXConnectorModel.java:294)
         at com.jrockit.console.rjmx.RJMXConnectorModel.<init>(RJMXConnectorModel.java:99)
         at com.jrockit.console.rjmx.RJMXConnectorModel.<init>(RJMXConnectorModel.java:113)
         at com.jrockit.mc.console.ui.actions.StartConsole$1.preConnect(StartConsole.java:36)
         at com.jrockit.mc.browser.utils.PreConnectJob.run(PreConnectJob.java:73)
         at org.eclipse.core.internal.jobs.Worker.run(Worker.java:55)
    Caused by: java.lang.ClassNotFoundException: com.vignette.monitor.framework.VgnMBeanInfo (no security manager: RMI class loader disabled)
         at sun.rmi.server.LoaderHandler.loadClass(LoaderHandler.java:371)
         at sun.rmi.server.LoaderHandler.loadClass(LoaderHandler.java:165)
         at java.rmi.server.RMIClassLoader$2.loadClass(RMIClassLoader.java:620)
         at java.rmi.server.RMIClassLoader.loadClass(RMIClassLoader.java:247)
         at sun.rmi.server.MarshalInputStream.resolveClass(MarshalInputStream.java:197)
         at java.io.ObjectInputStream.readNonProxyDesc(ObjectInputStream.java:1544)
         at java.io.ObjectInputStream.readClassDesc(ObjectInputStream.java:1466)
         at java.io.ObjectInputStream.readOrdinaryObject(ObjectInputStream.java:1699)
         at java.io.ObjectInputStream.readObject0(ObjectInputStream.java:1305)
         at java.io.ObjectInputStream.readObject(ObjectInputStream.java:348)
         at sun.rmi.server.UnicastRef.unmarshalValue(UnicastRef.java:290)
         at sun.rmi.server.UnicastRef.invoke(UnicastRef.java:139)
         ... 11 more
    thanks

    As poorem suggested, I would check that the time is the same on both the identity and vcac appliances.  It has been a while since I posted this question but I believe that did get me past that specfic error.  I changed the timezone on each and made sure the times were correct and the same.

  • I keep getting an unknown error when trying to connect to the store. I ran diagnostics and it says secure link to itunes store failed.

    I keep getting an unknown error when trying to connect to the store. I ran diagnostics and it says secure link to itunes store failed. I've tried all suggestions from apple and nothing will work.
    Please Help

    I received this email from Apple and this corrected the problem for me...  I only had to reset the iTunes cache
    1) Open iTunes
    2) At the top menu, click File > Preferences (iTunes > Preferences on a Mac)
    3) In the Preferences menu, click the Advanced tab
    4) In the Advanced menu, you should see a button that says "Reset Cache". Please click this button.

  • Getting Error when trying to connect to the Primavera database. PPM V7 SP3

    Hi Guys,
    Caused by: org.springframework.beans.factory.BeanCreationException: Error creating bean with name 'mailService' defined in class path resource [com/primavera/bre//com/primavera/bre/integration/intgconf.xml]: Invalid destruction signature; nested exception is org.springframework.beans.factory.support.BeanDefinitionValidationException: Couldn't find a destroy method named 'destroy' on bean with name 'mailService'
    I have looked into the intgserver.jar under P6IntegrationAPI/lib and looked the com.primavera.infr.srvcs.MailServiceImpl.java and can see that there is no destroy method whereas it is defined in the com.primavera.bre.intergration.intgconf.xml as below
    <!-- provides mail services -->
    <bean id="mailService" class="com.primavera.infr.srvcs.MailServiceImpl" init-method="init" scope="singleton" destroy-method="destroy"*+>
    <property name="adminManager"><ref bean="adminManager"/></property>
    <property name="threadPool"><ref bean="threadPool"/></property>
    <property name="settingsManager"><ref bean="settingsManager"/></property>
    </bean>
    I get the above error when trying to connect to the Primavera database. I use PPMV7 SP3 and I have installed the Integration API from EPPMV7 bundle.
    My demo's are working fine.
    Any help would be appreciated.
    Thanks,
    Kajal.

    Hi Marc,
    I am using a userid (is an admin)
    Using global login method and provided userid & password in integration settings.
    In the machine profiles, provided userid, password and domin.
    Not providing domain in weblogin.
    With all the above I am still getting error "Could not authenticate the specified user. %0" for HFM application
    And with the same settings I am not getting any error to connect to essbase cube.
    Any suggestions?
    Thanks
    Krishna

  • Errors when trying to connect CRM 7.0 to Enterprise Search

    Hi!
    I encountered 2 errors when trying to connect to a CRM 7.0 system as a backend system from Enterprise Search Cockpit.
    The first error is related to ESH_INT_GET_TREX_DESTINATION with a message of ESH_OM_OBJ_MODEL_REP 517:
    http://img39.imageshack.us/img39/9722/eserrors1.jpg
    The second error is related to "Errors during data cluster import from remote system":
    http://img97.imageshack.us/img97/7976/eserrors2.jpg
    I don't know if these two errors are related, but any help or suggestions will be greatly appreciated!!
    Thank you!
    Regards,
    Paul

    4.0 should be fine. My initial thoughts were on the script targetting a framework lesser than 3.5. Am bummed about the error cause in the line
    ClientContext clientContext =
    new ClientContext(client);
    it just creates an instance of the ClientContext class. It should have nothing to do with permissions cause it is not even trying to connect to the sharepoint site. So it looks like it can't find the assembly. Can you place the asembly
    under the Microsoft.Net\Framework folder of your machine. SSIS looks for custom assemblies in this folder on design time (Refer
    this) Worth a try hey!
    http://btsbee.wordpress.com/

  • Oracle Fatal error when trying to connect through sqlplus

    Hi,
    I am getting the below error when trying to connect to instance through sqlplus
    Database version is :10.2.0.3
    Operating system= Solaris Operating System (SPARC 64-bit)
    OS version=5.10
    [lscbd07p2*BMC]-\ORACLE>sqlplus
    SQL*Plus: Release 10.1.0.4.0 - Production on Fri Nov 9 07:48:24 2007
    Copyright (c) 1982, 2005, Oracle. All rights reserved.
    Enter user-name: /as sysdba
    ld.so.1: oracle: fatal: relocation error: file /u01/app/oracle/product/db/10.1.0.4/lib/libjox10.so: symbol kststop_: referenced symbol not found
    ERROR:
    ORA-12547: TNS:lost contact
    Enter user-name:
    Could you all please give me suggestions in order to solve this problem.
    Thanks
    Mannu

    Have you recently patched/upgraded? This sounds like there might have been a problem relinking the executables / libraries, and/or a permissions problem. For example you may be referencing a 32 bit library with your 64 bit client.
    I believe I recently read a similar case - check Metalink for this symptom.
    HTH
    Regards Nigel

  • Keep getting sync service error when trying to connect my iphone 5S.

    Keep getting sync service error when trying to connect my iphone 5S. It freezes itunes and I can't do anything else. I see that there is an update for my phone and I need to back up, upload new apps, etc before installing. I plug my phone in and get this error every time. I am using a Win 7 SP1

    Howdy Susie48825,
    It sounds like you are getting an error that mentions the sync services when you connect your phone to your computer and so you cannot sync your device. I would use the troubleshooting from the following article that  mentions an error regardign the sync services named:
    iTunes for Windows: "Unable to load data class" or "Unable to load provider data" sync services alert
    http://support.apple.com/kb/ts2690
    Start with these steps:
    1. Check that iTunes is up-to-date
    Ensure that you have updated to the latest version of iTunes.
    2. Reset Sync History
    Resetting your Sync History is a simple step which may resolve some syncing issues. If this works, iTunes will prompt to Merge or Replace the information on your device when you next attempt to sync. To reset your Sync History:
    Disconnect your device.
    Open iTunes.
    From the Edit menu, choose Preferences.
    Click the Devices tab.
    Click the Reset Sync History button, and then reconnect your device.
    If this resolves the issue, and you know all of your contacts, calendars, bookmarks and notes are on your computer:
    Reset the Sync History again using the steps above.
    Select the device in iTunes and click the Info tab.
    Scroll down to the Advanced section, and under "Replace information on this iPhone/iPad/iPod touch" select Contacts or Calendars.
    Click Apply.
    If the issue persists, and you know all your contacts, calendars, bookmarks and notes are on your iPhone, iPad, or iPod touch:
    Remove all of the contact and calendar information from Outlook.
    Select the device in iTunes and click the Info tab.
    Scroll down to the Advanced section, and under "Replace information on this iPhone/iPad/iPod touch" make sure Contacts and Calendars are not selected.
    Click Apply.
    There are additional steps to use in the article if needed, but these will get you started.
    Thank you for using Apple Support Communities.
    All the very best,
    Sterling

  • ORA-12560: TNS:protocol adapter error when trying to connect

    hopefully somebody can help me out... the problem i'm having is connecting to the scott/tiger database. i keep getting :
    "ORA-12560: TNS:protocol adapter error" when trying to connect to it. it worked previously, but i unistalled oracle 8i personal and reinstalled it. now it doesn't let me connect. what's going on?
    thanx,
    uriah

    You can run the net8 assistant to set up your tnsnames.ora file.
    start/programs/oracle/network administration/net8 assistant
    When you are done it should look something like this:
    ORCL =
    (DESCRIPTION =
    (ADDRESS_LIST =
    (ADDRESS =
         (PROTOCOL = TCP)
         (Host = )
         (Port = 1521)
    (CONNECT_DATA = (SID = ORCL))
    Bev

  • Receiving an error when trying to remove P00 Security role from the user

    Hi All,
    I am receiving an error when trying to remove P00 Security role from the user.
    After logging on to GRC CUP, clicking on u201CCreate requestu201D, and filling out required information,
    I click on Select Roles/Groups
    On the next screen,
    I click on Existing Roles/Groups
    ERROR MESSAGE appears X Action failed and no roles appear in the box to select for removal.
    Regards,
    Vineet

    Hi Vineet,
    My be your selection is incorrect
    Try this
    in Applicaiton Area -- Select ALL
    Functional Area  -
    Select ALL
    Company           -
    Select ALL
    Role/Profile/Group Names --- Give p00* and execute the report
    if you give only p00 it wont give any result
    Hope this helps
    Thank you,
    Kishore

  • Sql Server Web Edition Reporting Services errors when trying to connect to Windows Azure SQL

    I am using a preconfigured image from the Azure VM Gallery to create a VM.
    --> Sql Server 2012 SP1 Web running under Windows Server 2008 R2
    After configuring Reporting Services I get the following error when trying to run a report that connects to my Azure SQL db.
    An error has occurred during report processing. (rsProcessingAborted)
    An attempt has been made to use a data extension 'SQLAZURE' that is either not registered for this report server or is not supported in this edition of Reporting Services. (rsDataExtensionNotFound)
    On the VM using SSMS I can connect to the Azure SQL db.  On the VM in Report Builder when I define a connection I get a similar error to the one above when I test that connection.  I am using Microsoft Azure SQL as the data source type. 
    Interestingly in Report Builder, if I proceed past the connection definition, I can see the tables from my Azure SQL db in the dataset definition page.
    One more note.  If I use a different image from the Gallery (Sql Server 2012 Standard SP1 on Windows Server 2012) my report builder connection works and the reports run fine.  I believe that the Azure documentation says that Sql Server Web edition
    is an acceptable choice for the SSRS on VM for reporting.
    Any thoughts or suggestions?
    Thanks -- Tom Reilly

    Hello,
    A VM with SQL Server 2008 R2 or 2012 supports all Reporting Services features, including all supported data sources, customization and extensibility, and scheduled report execution and delivery.
    Did you run the report in Report Manager,or preview the report in Report Builder? Which version of the Report Builder you installed in the Windows Azure VM? SQL Reporting does not support reports created from Report Builder 1.0 or 2.0. You can create reports
    using Report Builder 3.0 and then upload the reports.
    What's more, please also check the database source credential of the report.
    Regards,
    Fanny Liu
    If you have any feedback on our support, please click here.
    Fanny Liu
    TechNet Community Support

  • '500 Internal Server Error' when trying to connect to Music Store

    Does ANYBODY at Apple CARE that I've been writing posts for 2 WEEKS trying to get an answer to the reason why I can't connect to the Music Store? This is absurd!
    Since upgrading to iTunes 6.0.3 (and now 6.0.5), I get a 'Music Store termporarily unavailable' message. I have the same PC, OS, and ISP that I've used to buy hundreds of dollars worth of your music - but since upgrading - I'm dead in the water. Norton is set to PERMIT i-tunes - but I get the same problem with Norton turned OFF.
    When trying to connect to the Music Store via the following URL: phobos.apple.com/WebObjects/MZStore.woa/wa/storeFront
    as suggested in other posts, I get a "Error 500 Internal Server Error" - which according to my ISP and Microsoft is on APPLE'S Server - not my end.
    HELP HELP HELP!!!!
    Dell   Windows XP Pro  
    Dell   Windows XP Pro  

    Check whether your DBControl or ASControl service is still running or crashed. EM is not able to connect to the Management Server.
    For instance in Windows, you may see that the Servise is not started. Then check for error logs in $ORACLE_HOME/sysman/logs for any related error messages in the log files

  • Console Error When Trying to Connect to Task Server

    I'm trying to set up an Apple Remote Desktop task server on our Xserve G5. I've successfully installed Apple Remote Desktop 3, but I'm having some weird problems with it.
    One thing that should be noted is that we don't have a monitor for our Xserve. Everything is done via Apple Remote Desktop. So I have to install Remote Desktop on the Xserve via Remote Desktop. (I don't know if this makes a difference, but I do know that Remote Desktop doesn't allow you to control a computer that is currently running Remote Desktop, so maybe this is part of the problem.)
    After installing Remote Desktop on the Xserve, I launched it, and when trying to control the application, it's very unresponsive. Clicking and holding on the icon in the Dock almost always says "Application not responding", and I can barely click on anything at all. I created an AppleScript that turned on the Remote Desktop task server, hoping that I wouldn't need to touch the Remote Desktop app on the Xserve anymore.
    The problem now, though, is that when I try to connect to the task server from another administration computer (by going to Remote Desktop preferences, "Task Server" tab, choosing "Use remote Task Server", entering the IP address of the Xserver, and then clicking select), it immediately reverts back to using the task server on the local computer.
    This also shows up in the console when trying to connect to the remote task server:
    MacBook-001959 /Applications/Remote Desktop.app/Contents/MacOS/Remote Desktop: setCollectionAtComputer: Got unexpected error (-6410) setting Admin entry in DOC.
    Has anyone had this problem before?

    Well, in fairness to Apple, the ARD license does say that each copy can only be installed on a single system. But I do agree that it would be nice if a more explicit "this serial number is in use on another system" message appeared (since it may not be known in some organizations that someone installed ARD elsewhere). You can suggest that to Apple through the feedback page.

  • ICloud encountered an error when trying to connect to server?

    When I log into ICloud I continue to get a message "ICloud encountered and error while trying to connect to the server"

    If it only does it at work, then the most likely reason is that your work network is blocking it, or one of the servers iCloud connects to.
    Have you asked the IT people at work? Checked it on another computer at work?

  • Why do I keep getting a connection error when trying to connect to SQL?

    Environment:
    LiveCycle ES2
    Windows Server 2008
    JBOSS
    Oracle Application DB
    When trying to connect to SQL, I get this error message in the log.
    Exception: Could not create connection; - nested throwable: (java.lang.UnsupportedOperationException: Java Runtime Environment (JRE) version 1.6 is not supported by this driver. Use the sqljdbc4.jar class library, which provides support for JDBC 4.0.); - nested throwable: (org.jboss.resource.JBossResourceException: Could not create connection; - nested throwable: (java.lang.UnsupportedOperationException: Java Runtime Environment (JRE) version 1.6 is not supported by this driver. Use the sqljdbc4.jar class library, which provides support for JDBC 4.0.))
    I have these two files located in \\jboss\server\lc_oracle_cl\lib
    sqljdbc.jar
    sqljdbc4.jar
    I was told all I needed to do was drop these two files in the directory above and restart JBOSS. Is there something I'm missing?
    Jesse

    Hi Jesse,
    The driver you are using is for SQLServer Database. Since you are using Oracle as your database, you need an oracle driver.Please copy ojdbc6.jar from the [installDir]/lib/db/oracle/ directory and try again.
    Thanks,
    Ruchi

  • Error when trying to connect in synch manager

    Hi there,
    When trying to connect to an administration in synch manager, an error appears: SBO Error #-111: Failed to Connect to SBOCommon
    System:
    SAP Business One 2007A PL42
    SQL Server 2005
    SAP Webtools 2007 PL 13
    Kind regards,
    Andy Grootens

    Hello Andy,
    Can you log in to this instance of business one normally?
    Did you set the username and password to connect in the synch manager?
    Have you recently changed the users password?
    James

Maybe you are looking for