Error while posting Inbound Idocs-"EDI: Partner profile not available"

Hi,
I am getting the error "EDI: Partner profile not available" Status -56 while creating inboud Idocs.
I have done the following steps so far
1.Created IDOC basic Type and Message Type. (Custom)
2. Created process code to process the IDOC.
3. Use the FM IDOC_INBOUND_WRITE_TO_DB to create the inbound IDOC.
4. Use the FM IDOC_START_INBOUND to process the IDOC.
Is ther anything else that i have to do inorder to post the idoc sucessfully.
Thanks in advance
-Nishant
Edited by: nishant patel on Nov 13, 2009 10:35 AM
Edited by: nishant patel on Nov 13, 2009 10:41 AM

Hi,
Check in WE20 if the partner profile is configured for the idoc type and the message type. That might be the cause of the error.
Also make sure the same partner profile details are sent to the control record. Partner profile details are stored in the table EDP13.
Hope this helps
Regards
Shiva

Similar Messages

IDOC is Getting Fail with - 56 Status EDI Partner profile not available

Hi,
I am trying to Post invoice Data into IDOC on ECC Side.
My Scenario is File u2013 XI u2013 ECC(IDOC).
But It is Getting Fail with 56 Status u201C EDI: Partner profile not available u201C
On Control record I am getting this
Port BLANKKKKKKKKKK
Partner Number CLNTDEC110 Logical system for Client
Partn.Type LS Logical system
Function BLANKKKKKKKKKK
Port SAPDPI
Partner number CLNTSAMPLE
Partn.Type LS Logical system
Partner Role BLANKKKKKKKKKK
My configurations are Like this :----
On ECC Side MY SID is DEC
On ECC side I have two logical system in CLNTDPI100 for PI
 CLNTDEC110 for ECC.
I have Partner profile on ECC system on CLNTDPI100 logical system - we20
Added message type in inbound side of partner Profile (INVOIC-INVOIC02)
ON SAP PI/ XI System MY SID is DPI
IDX 1 has Port name SAPDEC
On Message mapping EDI_DC40 is mapping with constants with below given value
<INVOIC02>
 <IDOC BEGIN="">
 <EDI_DC40 SEGMENT="">
 <TABNAM> </TABNAM>
 <DIRECT>2</DIRECT>
 <IDOCTYP> </IDOCTYP>
 <MESTYP>INVOIC</MESTYP>
 <SNDPOR>SAPDPI</SNDPOR>
 <SNDPRT>LS</SNDPRT>
 <SNDPRN>CLNTDPI100</SNDPRN>
 <RCVPOR>SAPDEC</RCVPOR>
 <RCVPRT>LS</RCVPRT>
 <RCVPRN>CLNTDEC110</RCVPRN>
 </EDI_DC40>
Regards
PS

Check the following :
in We 02 which partner number is displayed just in the posted IDOC -> 2nd coloum in the IDOC list .and verify if the
same you have in Partner profile. Actually this details comes from ECC business system's logical system name which you give in SLD.
in we 19 - take the error iDOC numner and open the IDOC ->click on the first line -> check entries as you mentioned
above sender port should be PI port not empty.you need to check the partner profiles properly
follow these steps
1. create a RFC destination of tyoe H for Pi system- 2. create a Port and assigen the RFC destination to it
3 create logical system for PI BD54 PICLNT001 say , 4 with the same name create a partner profile in We20
 in parter profile maintain the inbbound message parameters and add the PI port as receiver port in it .Give the basic type also .
now
for sender details in ur case PI : u have port (defined in PI IDX1),patner number (LS defined in ECC PICLNT001), parter type LS.
for receiver you have port defined (as above), partner number the logical system for ECC system.
in we 19 ,, edit the control record as above and go to the tab inbound processing and test the internal posting
it should work fine. in the adapte specific attribuet for receiver ECC system , maitain the same LS name , if any wrong entry is
there then change the LS in sld to poing to correct LS/
refer this
http://www.riyaz.net/blog/xipi-settings-in-r3-partner-system-to-receive-idocs/technology/sap/26/
Regards,
Srinivas

Getting EDI:Partner profile not available.

Hi,
I am a newbie to SAP XI. As I am doing File to IDOC scenario, I am getting error - EDI:Partner profile not available.
My Scenario details:
1. Created RFC Destination, RFC port, logical System and Partner profile in both Sender (XI) as well as Receiver(SAP R/3) systems.
2. Created SWCV, Technical sys, Business Systems in SLD. I used the Logical system created (for SAP R/3) on XI system in my business system.
3. Created Data type, Message type, Message interface, Message Mapping and Interface mapping in Integration Repository and activated them.
4. Imported IDOC from SAP r/3 system during Namespace creation and used it for mapping.
5. used Integration Directory wizard to create Communication channels, Sender & Receiver agreements, Receiver Determination, Interface Determination.
6. Creaed a new business service for sender and added "Adapter Specific Identifier with Logical system created (for SAP R/3) on SAP XI.
7. Activated all Standard Change list items.
The file for the above Scenario has been picked up amd i am getting "Chequered Flag" on both ends in "SXMB_MONI" monitor. When i change over to SAP R/3 to check idocs created (i.e., T.code - we05) my scenario idoc status is 56 and it says.. Status; Idoc with errors added.
I have gone through many of the forum suggestions and blogs regarding this issue, but still not able to resolve my problem.
can somebody suggest me solution please.
Thanks,
Vijay.

Hi,
6. Creaed a new business service for sender and added "Adapter Specific Identifier with Logical system created (for SAP R/3) on SAP XI.
>>>Check this for Reciever Business System.. not for Sender system..
BTW, if you get chequered flag in XI, then idoc data is sent from XI. Can you check all the data from XI is populated in the idoc structure in SAP R/3 in we05...by clicking each segment.. if so, then there is no problem from XI..
check WE20 ..partner profile configuration in R/3 also check inbound parameters are given
Regards,
Moorthy

EDI: Partner profile not available R/3 -- XI

Hallo,
when I send an IDoc-Message from R/3 to XI, I get following error:
"EDI: Partner profile not available" (transaction we05)
I have created the partner profiles in we20, but there are not available.
What could be the reason of this error?
I have created in XI a logical system "SAPR3" (transaction bd54) and I have assigned it the idoc-inbound-parameter (transaction we20). also the logical system of the business system "R3System" in the "adapter specific identifications" is "SAPR3".
So, is the "partner no name" of the idoc from the sender-system (r3) the reason? in transaction we05, it is called WMS.
Thanks in advance.
regards
Stefan

<<You need to set Outbound parameters.
<<Inbound parameters are set in case of XI to R/3 scenario
The sap-documentation (HowTo_IDOC_XI_Scenarios.pdf) says, that you should create a partner-profile in R3 with outbound-parameters and that you should create a partner-profile in XI with inbound-parameters for the direction r3 --> xi
Is this wrong?
following informations are from transaction we05 in XI:
recipient information
port:
partner number: XI
partner type: LS
function:
sender information
port: sapi4711
partner number: WMS
partner type: LS
partner role:
Which of them should I create as logical system in transaction bd54 (XI)?
Which of them should I use for partner no. in transaction we20 (XI)?
Should I create outbound or inbound-parameters?
Thanks.
Regards
Stefan

EDI: Partner profile not available in VF02

Hi Experts,
We are trying to generate IDOC using VF02 (billing).
We configured partner profile properly. And also we are using standard output type RD04 and application is V3. And using standard program & form routine (RSNASTED, EDI_PROCESSING).
While saving the document VF02, we are receing "EDI: Partner profile not available" message in the processing log file.
What might the problem? Where we are doing mistake.

Hi,
I am also facing this problem, this error is however coming for the billing documents pertaining to some sales organisation. For other sales organisations, the idoc is getting generated succesfully.
Can you suggest some reason for this?
Regards,
Jayesh

Re : EDI: Partner profile not available

Hi
while i am transfering material master i am getting the following error
' EDI: Partner profile not available'
How to solve

Hi,
First check the change pointers configuration for matmas and then check configuration part for that partner.
Check these threads for complete information on Change Pointers:
Change pointers
what are change pointers
Regards,
Raju.

EDI: Partner profile not available

Hi,
We have performed a client copy on the source system.
In RSA, source system check, errors occurred:
The following errors occurred in the source system: RSAR 374
EDI: Partner profile not available E0 332
Entry in inbound table not found E0 414
Entry in outbound table not found E0 400
In WE20, I click on the partner profile, check ok.
Pls assist.

Hi,
Try restore from context menu of the source system, this would recreate the partner profile entries.
regards,
Pruthvi R

EDI: Partner profile not available for the Ack received

Hi All,
All the scenarios are IDOC -->XI --> File
We have different scenarios of IDOC to File, where SAP sends IDOC to two (we have 5 here letu2019s say 2) diff FTP locations one say FTP1 and other FTP2 and we used 3 business systems in SLD.
1)      one for Sender SAP system(say BS_SAP) and assigned a Logical System say LS_SAPCLNT100
2)     Second one for the receiver FTP1 and assigned a Logical System LS_FTP1
3)     Third one for the receiver FTP2 and assigned a Logical System LS_FTP2
And we are getting the error in the Sender SAP System for the acknowledgement sent from the FTP1 server EDI: Partner profile not available for the LS_FTP1 when we send the IDOC to FTP1 and EDI: Partner profile not available for the LS_FTP2 when we send the IDOC to FTP2.
This is because in SAP we do not have the Logical Systems for LS_FTP1 and LS_FTP2.
Now my question is how to get rid of this? Do we need to create Logical systems in SAP for third Party Systems?
If not how to overwrite and use a single LS for all of the third party Business Systems?
Please suggest .
Regards,
Sridhar Reddy

And we are getting the error in the Sender SAP System for the acknowledgement sent from the
FTP1 server uF0E0EDI: Partner profile not available for the LS_FTP1 when we send the IDOC to FTP1 and EDI: Partner profile not available for the LS_FTP2 when we send the IDOC to FTP2.
did you get a chance to go through the below threads:
ERROR: idoc in R/3
check out the blogs mentioned in the above link...
Also check the last point (9) mentioned in the below blog:
/people/venugopalarao.immadisetty/blog/2007/01/24/troubleshooting-file-to-idoc-scenario-in-xi

B1358 error while posting inbound idoc with a FM

Hi
We are trying to post and inbound IDOC with the help of an rfc and eventually creating an invoice from a bdc wrapped in the RFC
The idocs are successfully pushed to R/3 while they are not getting posted and the error code in we02 is as follows
No status record was passed to ALE by the application
Message no. B1358
Diagnosis
The application failed to return a status record to the ALE layer after the IDoc was processed.
This is due to an error in the application function module which processed the inbound IDoc.
Procedure
If you wrote the application function module yourself, you need to change the program.
If the function module in question is a standard application function module, you should consult SAP.
Note: we are using a custom function module
regards
krishna

Hi Krishna,
I assume that your function module processing the IDOC does not follow the ALE/IDOC processing rules.
Please check out the programming guidelines in the SAP Online Help under:
<a href="http://help.sap.com/saphelp_nw70/helpdata/en/78/21758051ce11d189570000e829fbbd/frameset.htm">http://help.sap.com/saphelp_nw70/helpdata/en/78/21758051ce11d189570000e829fbbd/frameset.htm</a>
Important are the parameters and tables that need to be returned, containing the correct IDOC processing status. Please take the IDOC processing quite serious in regards to complete Logical Unit of Works.
Best regards,
SIlvia

Error: EDI partner profile not available

Hi all,
We just installed CRM and BW servers and trying to integrate them. After creating CRM Source system in BW, during Activation its giving following errors:
1. No Partner Profile (outbound parameter) could be found using the following key: /CLNT001/LS//RSSEND////This refers to the key fields in table EDP13: (RCVPRN, RCVPRT, RCVPFC, MESTYP, MESCOD,TEST)
2. No Partner Profile (outbound parameter) could be found using the following key: /CLNT001/LS//RSINFO////This refers to the key fields in table EDP13: (RCVPRN, RCVPRT, RCVPFC, MESTYP, MESCOD,TEST)
3. No Inbound Partner Profile could be found with the following key: /CLNT001/LS//RSRQST//// Key consists of following fields (SNDPRN, SNPPRT, SNDPFC, MESTYP, MESCOD, MESFCT, TEST)
4. A Partner Profile could not be found with the following key: /CLNT001/LS/, This involves the key fields of table EDPP1 (PARNUM, PARTYP)
Please let me know how to resolve these errors. I'm unable to solve these as i've very little experience with both CRM and BW.
Thanks & Regards,
Vikas Sharma

Hi Vikas,
Please check your partner profilesin the transaction WE20. Check if there is a TRFC port connected to your client system in transaction WE21. If not maintained, you will have to ask basis team to maintain these settings. If they are maintained, check your trfc connectivity in SM59.
Thanks and Regards
Subray Hegde

Workflow Inbox - "EDI: Partner profile not available"

Hi,
This is very strange, all the users, including new ones, as soon as they open their workplace inbox, there're about 10 of the above messages in it.
I've tried to clicked all possible buttons, still can't get rid of them. Anyone has the same experience before? How do I make them disappear?
Thanks,
Kathryn

thanks so much guys!
I had a look at WE20, there's already assignemnt to ALREMOTE.
In WE46, where do I assign the admin for EDI error handling? the only blank tabs there are 'Express Indicator' and 'Inactive'.
Thanks,
Kathryn

Error while posting the IDOC. Status message '56'

Hi,
I have a requirement where I will post an IDOC which inturn will split the original IDOC into child IDOCs based on the store value.
I am trying to post the IDOC in WE19. So, the Original IDOC is posted successfully with status '53'. Whereas, the child IDOCS finished with error. The status of the message is '56' and the error says 'EDI: Partner profile not available'. Could someone tell me what could be the reason for this..?
Actually, the IDOC was created by the Functional Consultant. So, should the partner profile creation also done by them or do we need to do anything to solve this problem.? Could someone answer me this question. Thanks in advance.
Best Regards,
Paddu.

It looks like the control data for the child segment is not getting populated. you have to find the code which populated the control data and see if it is doing what it should.

EDI partner profile not found

Hi All,
We are facing a recurring issue which happens in BW QA system after we refresh is from the BW production system.
After about a week or so after the refresh, the data loads halt in the BW QA system and the BW team gets an error "EDI partner profile not available".
After i checked, i found that the logical system name entry for the EDW QA system (i.e. self system entry) is missing from the table EDPP1 and also from transaction WE20.
I re-created it in WE20 and the entry automatically got created in EDPP1 table.
My question is : I suspect that some job or application program is deleting this entry. We checked the background jobs but no luck.
How do i resolve this error. The client has come up with this question and he wants an answer as to why this
entry is being automatically.
Can you please help?
Regards,
Hari Kishan

Hi Ruchit,
Yes. We run BDLS correctly. In fact, ONLY after BDLS jobs complete correctly, then we proceed with the further steps.
However, as per your sugesstion, i went to BD64 but couldn;t find any relevant distribution model.
Can you please elaborate this?
I am still unable to understand how the entry "OBC100" is suddenly disappearing.
One day, it is there and the BW loads run fine.
Suddently, one day, its not there. This has happened on 2 occassions one week after the refresh.
Regards,
Hari Kishan

EDI / IDoc : While posting inbound IDocs, IDocs gets into status 56

EDI / IDoc : While posting inbound IDocs, IDocs gets into status 56 with message "EDI: Sender port in control record is invalid".
But if I reprocess the same idoc without doing any changes using RBDINPUT and select radio button to processs idocs for status 56, then it gets successfully posted.
So not getting why this stucks for the first time.
Thanks in Advance..........

i fixed this my self

Status 56 : EDI Inbound Partner Profile not available

I am trying to load an inbound 856 IDoc from EdI subsystem to SAP. It si giving me an error 56 saying Inbound partner profile not available.
I have set up the partner as Vendor in we20. Is there any other place that I need to set up the partner. We have inbound docs coming in as a customer(KU) but this is first vendor set up
Do you know what I am missing?
When I clicked on status message 56 -- says /ICPLPLIVA/LI/LF/DESADV///T/....key fields missing in EDP21? is the error really meant that?
Thanks in advance

Hi,
Can you tell us about the IDoc control record?
In order to determine whether need to setup LI or KU partner profile.
Please go to WE02 and check the IDoc control record.
What are the values in partner tab?
Port             ???
Partner number   ???
Partn.Type       ???
Function
Port             ???
Partner number   ???
Partn.Type       ???
Partner Role
Regards,
Ferry Lianto

Error while posting Inbound Idocs-"EDI: Partner profile not available"

Similar Messages

Maybe you are looking for