Error while using '*'in the NTE (EDI 850) Segment where '*' is also used as Data Element
Hi All,
I am facing below mentioned error while using '*'in the NTE (EDI 850) Segment where '*' is also used as Data Element
Error: 1 (Field level error)
SegmentID: NTE
Position in TS: 70
Data Element ID: NTE02
Position in Segment: 2
Data Value:
3: Too many data elements
For Eg: NTE*GEN*My Text *goes here
Here, NTE02 should be My Text *goes here. So, how can I use "*" here without changing anything in the EDI message?
Can it be done?
Thanks.
Sorry, no.
X12 does not support an escape character so whatever is used for delimiters become reserved characters.
If you want to allow '*' in the data, you will have to chooser a different Element delimiter. The receiver should read the from this from the ISA Segment so it's supposed to be dynamic but that's not always the case in practice.
Similar Messages
-
How to use '*' as data Element in the NTE(Edi 850) Segment
Hi All,
I am facing a field level error while using '*' in EDI 850 (NTE segment). '*' is also used as Data Element.
For Eg: NTE*GEN*My Text *goes here
Here, NTE02 should be My Text *goes here. So, how can I use "*" here without changing anything in the EDI message?
I have asked this question before
http://social.msdn.microsoft.com/Forums/en-US/1668e8d8-ee99-4d79-961b-8d26f3a496f8/error-while-using-in-the-nte-edi-850-segment-where-is-also-used-as-data-element?forum=biztalkediandas2
The answer in the above forum was to ask client modify the EDI message.
Previously, our client was using a different technology (other than BizTalk) which was working fine with this format. So, they are insisting on this format only.
Thanks,Sorry, the answer is the same.
It doesn't matter what EDI platform either side is using, the '*' in the field content conflicts with the '*' that is the element delimiter. That is invalid EDI, there is no way around that short of writing a custom EDI parser.
It's not clear if you're sending or receiving this message. But again, it's really doesn't matter.
1. Change the Element Delimiter to something other than '*'. < or > are not uncommon.
2. If you are receiving the EDI, create a custom Pipeline Component that "handles" NTE02 either by replacing the '*' with a substitute char or deleting it.
3. If you are receiving, you could add extra elements to NTE to accommodate extra fields (since that's how the parser will see them). Then you can join them again in a Map. -
I got the above error while i restore the standby database using RMAN backu
Dear All,
RMAN> crosscheck archivelog all;
using target database controlfile instead of recovery catalog
allocated channel: ORA_DISK_1
channel ORA_DISK_1: sid=14 devtype=DISK
specification does not match any archive log in the recovery catalogi got the above error while i restore the standby database using RMAN backup from production.
Help need.i take the backup without catalog database.
regards,
DBrman> list backup;
it shows lengthier but i showed only the corresponding
BS Key Type LV Size Device Type Elapsed Time Completion Time
3479 Full 17G DISK 01:29:42 09-FEB-13
BP Key: 3479 Status: AVAILABLE Tag: 09FEB13_FULL_ESMSRV1_DB
Piece Name: /oradatabkp/rman/esmsrv1_full_db_09feb13
SPFILE Included: Modification time: 08-FEB-13
List of Datafiles in backup set 3479
File LV Type Ckp SCN Ckp Time Name
1 Full 1759250260 09-FEB-13 /esmsrv1/dbs/system01.dbf
2 Full 1759250260 09-FEB-13 /esmsrv1/dbs/undotbs01.dbf
3 Full 1759250260 09-FEB-13 /esmsrv1/dbs/cwmlite01.dbf
4 Full 1759250260 09-FEB-13 /esmsrv1/dbs/drsys01.dbf
5 Full 1759250260 09-FEB-13 /esmsrv1/dbs/example01.dbf
6 Full 1759250260 09-FEB-13 /esmsrv1/dbs/indx01.dbf
7 Full 1759250260 09-FEB-13 /esmsrv1/dbs/odm01.dbf
8 Full 1759250260 09-FEB-13 /esmsrv1/dbs/tools01.dbf
9 Full 1759250260 09-FEB-13 /esmsrv1/dbs/users01.dbf
10 Full 1759250260 09-FEB-13 /esmsrv1/dbs/xdb01.dbf
11 Full 1759250260 09-FEB-13 /esmsrv1/dbs/dpipe_default_seg_001.dbf
12 Full 1759250260 09-FEB-13 /esmsrv1/dbs/dpipe_property_ind_seg_001.dbf
13 Full 1759250260 09-FEB-13 /esmsrv1/dbs/dpipe_property_seg_001.dbf
14 Full 1759250260 09-FEB-13 /esmsrv1/dbs/dpipe_upload_ind_seg_001.dbf
15 Full 1759250260 09-FEB-13 /esmsrv1/dbs/dpipe_upload_seg_001.dbf
16 Full 1759250260 09-FEB-13 /esmsrv1/dbs/dpipe_rate_ind_seg_001.dbf
17 Full 1759250260 09-FEB-13 /esmsrv1/dbs/dpipe_rate_seg_001.dbf
18 Full 1759250260 09-FEB-13 /esmsrv1/dbs/dpipe_summary_ind_seg_001.dbf
19 Full 1759250260 09-FEB-13 /esmsrv1/dbs/dpipe_summary_seg_001.dbf
20 Full 1759250260 09-FEB-13 /esmsrv1/dbs/dpipe_overflow_seg_001.dbf
21 Full 1759250260 09-FEB-13 /esmsrv1/dbs/dpipe_overflow_seg_002.dbf
22 Full 1759250260 09-FEB-13 /esmsrv1/dbs/dpipe_summary_seg_002.dbf
23 Full 1759250260 09-FEB-13 /esmsrv1/dbs/perfstat_001.dbf
39 Full 1759250260 09-FEB-13 /esmsrv1/dbs/oem_repository.dbf
BS Key Type LV Size Device Type Elapsed Time Completion Time
3480 Full 17G DISK 01:21:30 09-FEB-13
BP Key: 3480 Status: EXPIRED Tag: TAG20130209T200021
Piece Name: /oradatabkp/rman/esmsrv1/esmsrv1_full_Feb09
SPFILE Included: Modification time: 08-FEB-13
List of Datafiles in backup set 3480
File LV Type Ckp SCN Ckp Time Name
1 Full 1759422265 09-FEB-13 /esmsrv1/dbs/system01.dbf
2 Full 1759422265 09-FEB-13 /esmsrv1/dbs/undotbs01.dbf
3 Full 1759422265 09-FEB-13 /esmsrv1/dbs/cwmlite01.dbf
4 Full 1759422265 09-FEB-13 /esmsrv1/dbs/drsys01.dbf
5 Full 1759422265 09-FEB-13 /esmsrv1/dbs/example01.dbf
6 Full 1759422265 09-FEB-13 /esmsrv1/dbs/indx01.dbf
7 Full 1759422265 09-FEB-13 /esmsrv1/dbs/odm01.dbf
8 Full 1759422265 09-FEB-13 /esmsrv1/dbs/tools01.dbf
9 Full 1759422265 09-FEB-13 /esmsrv1/dbs/users01.dbf
10 Full 1759422265 09-FEB-13 /esmsrv1/dbs/xdb01.dbf
11 Full 1759422265 09-FEB-13 /esmsrv1/dbs/dpipe_default_seg_001.dbf
12 Full 1759422265 09-FEB-13 /esmsrv1/dbs/dpipe_property_ind_seg_001.dbf
13 Full 1759422265 09-FEB-13 /esmsrv1/dbs/dpipe_property_seg_001.dbf
14 Full 1759422265 09-FEB-13 /esmsrv1/dbs/dpipe_upload_ind_seg_001.dbf
15 Full 1759422265 09-FEB-13 /esmsrv1/dbs/dpipe_upload_seg_001.dbf
16 Full 1759422265 09-FEB-13 /esmsrv1/dbs/dpipe_rate_ind_seg_001.dbf
17 Full 1759422265 09-FEB-13 /esmsrv1/dbs/dpipe_rate_seg_001.dbf
18 Full 1759422265 09-FEB-13 /esmsrv1/dbs/dpipe_summary_ind_seg_001.dbf
19 Full 1759422265 09-FEB-13 /esmsrv1/dbs/dpipe_summary_seg_001.dbf
20 Full 1759422265 09-FEB-13 /esmsrv1/dbs/dpipe_overflow_seg_001.dbf
21 Full 1759422265 09-FEB-13 /esmsrv1/dbs/dpipe_overflow_seg_002.dbf
22 Full 1759422265 09-FEB-13 /esmsrv1/dbs/dpipe_summary_seg_002.dbf
23 Full 1759422265 09-FEB-13 /esmsrv1/dbs/perfstat_001.dbf
39 Full 1759422265 09-FEB-13 /esmsrv1/dbs/oem_repository.dbf
BS Key Type LV Size Device Type Elapsed Time Completion Time
3481 Full 4M DISK 00:00:03 09-FEB-13
BP Key: 3481 Status: AVAILABLE Tag: TAG20130209T212205
Piece Name: /oradatabkp/rman/esmsrv1/esmsrv1_controlfile_copy_Feb09
Controlfile Included: Ckp SCN: 1759462488 Ckp time: 09-FEB-13
BS Key Type LV Size Device Type Elapsed Time Completion Time
3482 Full 0 DISK 00:00:01 09-FEB-13
BP Key: 3482 Status: AVAILABLE Tag: TAG20130209T212212
Piece Name: /oradatabkp/rman/esmsrv1/esmsrv1_spfile_copy_Feb09
SPFILE Included: Modification time: 08-FEB-13
ls -l /oradatabkp
root@drsrv1#ls -l /oradatabkp
total 1108672
drwxr-xr-x 2 ovsd dba 96 Sep 27 2009 alert_bkp
-rw-r--r-- 1 oracle dba 195 Mar 15 2007 create.sql
drwxr-xr-x 2 oracle dba 8192 Aug 7 2009 ctrl_bkp
-rw-r--r-- 1 root sys 565114880 Apr 24 2007 drsrv1.tar
drwxrwxrwx 2 root sys 96 Jun 17 2011 drsrv2-ignitebkp
drwxr-xr-x 4 root sys 96 Apr 24 2007 esmsrv1
-rw-r----- 1 root sys 1613824 Feb 22 2007 esmsrv1stby.ctl
-rw-r--r-- 1 esmsrv1 dba 5120 Dec 31 2009 esmtables.dmp
-rw-r--r-- 1 esmsrv1 dba 538 Dec 31 2009 esmtables.log
drwxrwxrwx 4 root sys 8192 Mar 10 2009 export
drwxr-xr-x 8 root sys 8192 Apr 24 2007 finalbackup
-rw-r--r-- 1 oracle dba 3820 Sep 5 2008 invalid.sql
-rw-r--r-- 1 esmsrv1 dba 303104 Dec 31 2009 kirdevports.dmp
-rw-r--r-- 1 esmsrv1 dba 591 Dec 31 2009 kirdevports.log
drwxr-xr-x 2 root root 96 Feb 12 2007 lost+found
-rw-r--r-- 1 oracle dba 24954 Aug 9 2009 ovcontrol-090909.ctl
drwxr-xr-x 22 root sys 8192 Apr 24 2007 ovpi
drwxr-xr-x 2 oracle dba 8192 Aug 7 2009 pfile_bkp
drwxrw-rw- 4 oracle dba 8192 Feb 10 15:25 rman
drwxr-xr-x 28 root sys 8192 Feb 1 17:15 schedbkp
drwxr-xr-x 2 oracle dba 8192 Jul 11 2011 sdnnm
-rw-r--r-- 1 esmsrv1 dba 2196 Dec 31 2009 srirdevports.log
drwxr-xr-x 2 oracle dba 96 Mar 13 2009 statsreport
-rw-r--r-- 1 oracle dba 966 Mar 15 2007 tbs.sql
drwxr-xr-x 5 oracle dba 96 Mar 16 2007 testov
drwxr-xr-x 2 root sys 442368 Mar 11 2009 trendadm_files
root@drsrv1#ls -l /oradatabkp/rman
total 37244448
drwxr-xr-x 2 oracle dba 8192 Feb 10 15:25 esmsrv1
-rw-r----- 1 oracle dba 19068198912 Feb 9 14:21 esmsrv1_full_db_09feb13
drwxrw-rw- 2 oracle dba 8192 Feb 9 21:36 openview
-rw-r--r-- 1 oracle dba 920442 Feb 9 21:37 rmanbkp-all.log -
DPM encountered an error while reading from the recovery point used for recovery.
Hi Guys I'm getting this error:
DPM encountered an error while reading from the recovery point used for recovery. Either the recovery point no longer exists or, if you
selected a share for recovery, the path to its contents is missing from the recovery point. (265)
The DPM Server is on Windows 2012 DPM is 2012R2 4.2.1273.0
The Server being backed up is 2012 R2 with DPM Agent 4.2.1273.0
The Server has 3 Data Volumes (C: Drive) and D and E its the D and E drive that i get this error if i try and recover data from DPM. the C Drive is fine. the D and E Drive are different
in that 1 De-dupe is enabled and 2 the Shadow Copies for these Volumes are stored on separate Disks F and G respectively.
I've removed the Protection from drives D and E and reinstated it but every recovery point created
brings up the same error message. I'm not sure where to go next do I need to Protect the Disks that have the Shadow copies on also? Many thanks in advance Gordon.Hi,
It seems you are in a configuration where the Windows 2012 based DPM server does not understand how to read Windows 2012 R2 Dedup data structure which is what the DPM replica volume is.
See the DPM supported and unsupported scenarios
here under the deduplication issues section.
We have a fix in DPM2012 R2 UR5 that will protect the Windows 2012 R2 dedup volume in a non-dedup state on the DPM Server, but unfortunately that will not allow previous recovery points to be read.
KB3021791-Description of Update Rollup 5 for System Center 2012 R2 Data Protection Manager
Backup job for dedupe-enabled volume on Windows 2012 R2 fails. For example, Data Protection Manager backup might fail for following setup:
Data Protection Manager2012 R2 is installed on Windows Server 2012.
Data Protection Manager is protecting a dedupe-enabled volume on Windows Server 2012 R2.
This also applied to restores as the above was for D2D2T backup that may fail as it needs to read the recovery point to back it up to tape.
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread. Regards, Mike J. [MSFT] This
posting is provided "AS IS" with no warranties, and confers no rights. -
Error while connecting to the database from a JSP Page
Hi,
I am using a simple JSP page which is based on the sample JSP pages from OTN.
When I try to connect to my database using the following code:
InitialContext ic = new InitialContext();
OracleDataSource ds = (OracleDataSource)ic.lookup("jdbc/OTN9iDS");
m_connection = ds.getConnection();
I get the following error:
Naming exception Error while connecting to the database : javax.naming.NameNotFoundException: jdbc/OTN9iDS not found in JDBCTest-JDBCTestProject-webapp
Does anybody know wht this is happening?
Any help would be appreciated
FRankHi Frank,
Are you using standalone OC4J or 9iAS ? If you are using standalone OC4J then you need to add a proper data source entry in %OC4J_HOME%j2ee\home\config\data-sources.xml file.
If you are using 9iAS the you can log in to the Enterprise Manager console and add the data source entry by using wizard provided by 9iAS.
Ensure the case of the JNDI lookup string, since, it is case sensitive.
Hope this helps.
Abhijeet -
I am getting the attached error while bringing up the Prcs Scheduler
I am getting the attached error while bringing up the Prcs Scheduler:
Cannot open message catalog TMADMIN_CAT
Starting Process Scheduler Server PSNT for Database FSUAT ...
NLS:4: Cannot open message catalog CMDTUX_CAT, set 1, num 752; check TUXDIR=C:\b
ea\Tuxedo8.1, LANG=English_United States.1252
INFO: BEA Tuxedo, Version 8.1, 32-bit, Patch Level 192
NLS:4: Cannot open message catalog LIBTUX_CAT, set 1, num 1571; check TUXDIR=C:\
bea\Tuxedo8.1, LANG=English_United States.1252
NLS:4: Cannot open message catalog LIBTUX_CAT, set 1, num 1570; check TUXDIR=C:\
bea\Tuxedo8.1, LANG=English_United States.1252
NLS:4: Cannot open message catalog CMDTUX_CAT, set 1, num 793; check TUXDIR=C:\b
ea\Tuxedo8.1, LANG=English_United States.1252
exec BBL -A :
NLS:4: Cannot open message catalog CMDTUX_CAT, set 1, num 820; check TUX
DIR=C:\bea\Tuxedo8.1, LANG=English_United States.1252
NLS:4: Cannot open message catalog CMDTUX_CAT, set 1, num 801; check TUXDIR=C:\b
ea\Tuxedo8.1, LANG=English_United States.1252
exec PSDSTSRV -p 1,600:1,1 -sPostReport -- -C psprcs.cfg -CD FSUAT -PS PSNT -A s
tart -S PSDSTSRV :
NLS:4: Cannot open message catalog CMDTUX_CAT, set 1, num 1685; check TU
XDIR=C:\bea\Tuxedo8.1, LANG=English_United States.1252
tmboot: NLS:4: Cannot open message catalog CMDTUX_CAT, set 1, num 827; check TUX
DIR=C:\bea\Tuxedo8.1, LANG=English_United States.1252
tmshutdown -y
NLS:4: Cannot open message catalog CMDTUX_CAT, set 1, num 753; check TUXDIR=C:\b
ea\Tuxedo8.1, LANG=English_United States.1252
NLS:4: Cannot open message catalog CMDTUX_CAT, set 1, num 916; check TUXDIR=C:\b
ea\Tuxedo8.1, LANG=English_United States.1252
NLS:4: Cannot open message catalog CMDTUX_CAT, set 1, num 907; check TUXDIR=C:\b
ea\Tuxedo8.1, LANG=English_United States.1252
NLS:4: Cannot open message catalog CMDTUX_CAT, set 1, num 936; check TUXDIR=C:\b
ea\Tuxedo8.1, LANG=English_United States.1252
NLS:4: Cannot open message catalog CMDTUX_CAT, set 1, num 948; check TUXDIR=C:\b
ea\Tuxedo8.1, LANG=English_United States.1252
NLS:4: Cannot open message catalog CMDTUX_CAT, set 1, num 775; check TUXDIR=C:\b
ea\Tuxedo8.1, LANG=English_United States.1252
Please advise, thank youIs that ever running ? Where/how did you installed tuxedo ? Which OS user was used for tuxedo install ?
Nicolas. -
I have been using facetime on my iphone5 for a while and after the recent IOS update, I cannot seems to use my facetime any longer. what went wrong?
'The installer has insufficient privileges to modify this file C:\Program Files (x86)\Common Files\Apple\Apple Application Support\Web kit.resources\inspector\Images\Spinner Inactive Selected.gif.'
That one's consistent with disk/file damage. The first thing I'd try with that is running a disk check (chkdsk) over your C drive.
XP instructions in the following document: How to perform disk error checking in Windows XP
Vista instructions in the following document: Check your hard disk for errors
Windows 7 instructions in the following document: How to use CHKDSK (Check Disk)
Select both Automatically fix file system errors and Scan for and attempt recovery of bad sectors, or use chkdsk /r (depending on which way you decide to go about doing this). You'll almost certainly have to schedule the chkdsk to run on startup. The scan should take quite a while ... if it quits after a few minutes or seconds, something's interfering with the scan.
Does the chkdsk find/repair any damage? If so, can you get an install to go through properly afterwards? -
Message failing in SXMB_moni----Error while reading from the secure store
Hi,
The scenario is as below
A file is picked up from a folder and processed to enrich it.This enriched file is then written back in a different folder.
The message is failing in sxmb_moni while trying to write the file in the folder.
The PI system is a system copy of another system and few of the configuration objects are transported through a tpz file to this PI system.The file receiver channel used to write this file is also transported through this tpz file.
Below is the error seen in moni.:
<?xml version="1.0" encoding="UTF-8" standalone="yes" ?><!-- Call Adapter --> <SAP:Error xmlns:SAP="http://sap.com/xi/XI/Message/30" xmlns:SOAP="http://schemas.xmlsoap.org/soap/envelope/" SOAP:mustUnderstand="1"><SAP:Category>XIServer</SAP:Category><SAP:Code area="INTERNAL">AE_DETAILS_GET_ERROR</SAP:Code><SAP:P1/><SAP:P2/><SAP:P3/><SAP:P4/><SAP:AdditionalText>Error while reading from the secure store: ERROR_U: No service user password found for Adapter Engine</SAP:AdditionalText><SAP:Stack>Error while reading access data (URL, user, password) for the Adapter Engine
</SAP:Stack><SAP:Retry>M</SAP:Retry></SAP:Error>
Below is Trace log:
<Trace level="1" type="B" name="PLSRV_CALL_ADAPTER"></Trace><!-- ************************************ -->
<Trace level="1" type="B" name="CL_XMS_MAIN-CALL_PLSRV"></Trace><!-- ************************************ -->
<Trace level="1" type="B" name="CL_XMS_MAIN-CALL_PLSRV_LOCAL"></Trace><!-- ************************************ -->
<Trace level="1" type="B" name="CL_XMS_PLSRV_IE_ADAPTER-ENTER_PLSRV">
<Trace level="1" type="B" name="CL_XMS_PLSRV_CALL_XMB-CALL_XMS_HTTP"></Trace><!-- ************************************ -->
<Trace level="1" type="T">error reading secstore:Error while reading from the secure store: ERROR_UNKNOWN: System-dependent data for entry changed: / (SECSTORE,031) </Trace>
<Trace level="1" type="System_Error">Error while reading access data (URL, user, password) for the Adapter Engine </Trace>
</Trace>
</Trace>
<Trace level="1" type="System_Error">Error exception return from pipeline processing! </Trace>
<Trace level="1" type="B" name="CL_XMS_MAIN-WRITE_MESSAGE_TO_PERSIST"></Trace><!-- ************************************ -->
Is this because PI system is a system copy of another system ?
Regards,
SnehaError while reading access data (URL, user, password) for the Adapter Engine
Check out Michal's reply:
Re: URL for Central Adapter Engine
As you said there was a system copy it may be the case that some things were not configured properly -
Error while communicating with the server
Hi Experts,
I'm having the following issue, when I try to send data using an input schedule the server says that there was an error while communicating with the server and don't send the data, I took a look at the log file and it says the following,
==============[BPC Logging]==============
[Message Type] : ERROR
[Job Name] : OSoft.Services.Application.FileAccessService.FileAccessServiceProxy
[DateTime] : 4/6/2011 8:42:44 AM
[UserId] : CAMESAP\BPC_SYSADMIN
[Message] : UJF_EXCEPTION E018 Cannot find document/directory 0
==============[BPC Logging End ]==============
Also i went to take a look at the default script logic, because i remember that this error happened to me when i wrongly program an script logic in the default.lgf but it shows me the following error when I open it,
System.InvalidCastExeption: Specified cast is not valid
at System.data.DataColumnCollection.get_Item(String name)
at System.data.DataRow.get_Item(String columnName)
at Osoft.Consumers.Admin.AdminLogicClient50.LogicMain.GetLogic()
If I compile the file, the error stop appearing, put with all new logic files it happens at first, I think that these two errors are very deep related, if anyone can help me will be very appreciated,
Thanks in advancedHi,
I have faced the similar kind of problem in BPC NW 7.5 SP5.
The main reason is when you are trying to send any data via input schedule, you will get this web server communication issue.
1) Check if any thing you are calling script logic under default.LGF. Exclude the logic out from default and test it.
2) Process all the dimensions in application
3) Perform Lite optimization and check are there any errors.
4) Finally check BPC COM+ services and check if any service stopped and also check osoft send governer service in microsoft services.
5) Diagnoise usign server manager.
6) Try input some thing in apshell and check if u face the same web server communication error? -
Error while logging in the BPC
Hi All
We are using BPC MS version.
We have encountered the following error, while Logging into the server :
' Cannot insert duplicate key row in object ' dbo.TBLDEFAULTS' with unique index ' IX_tbldefaults'. The statement has been terminated.
I have also seen note no. 1326648 but we are alredy on SP005
If anybody, has solution for this, please let us know.
Thanks & Regards
Rushabh Doshi
Edited by: R201184 on Nov 19, 2009 3:38 AMUsually this happen when you have a bad restore of an appset.
Or it can happen when you are doing a reimage of one computer into another computer.
Into tbldefault from appset where you try to connect it seems you have some duplicate records and this is causing the issue.
You have to find these duplicate records and to leave just a single record.
Regards
Sorin Radulescu -
Error while consolidating. The operation could not be completed.
Error while consolidating. The operation could not be completed. Cocoa error 13. (null)
Got this when I was trying to consolidate some referenced photoshop files. If failed to create a new version as well when I tried to open the files in Photoshop. I rebuilt the the library and it displays and exports both masters and version just fine, but it won't let me consolidate the master to the library.
What gives?I think that error was due to the fact that I hadn't upgraded MAC OSX after installing it. I have done that now and now I get another error saying the masters are offline.
I found this old thread: https://discussions.apple.com/thread/1965601?start=0&tstart=0 which seems to be the same problem. This is a whole other topic so I will start a new thread, but leave this in case anyone gets the same problem as me. Upgrade your OSX. That's the solution :-) -
Object failed to run due to an error while processing on the Job Server
when i am scheduling a report ith email notification i am getting below error
error msg: Object failed to run due to an error while processing on the Job Server
i have configured email notification in bo cmc and server also SMTP enabled. while scheduling report to ueser i am getting error and even mails are delivered to users as well.hi prithvi,
i am able to schedule reports to other destinations and reports are delivered as per the requirement.
i am able to telnet SMTP server from Adaptive job server machine on SMTP port.
have to check errors on log file....
@ COULD YOU PLEASE LET ME KNOW USER CAN SEND A MAIL TO USER IN SAME DOMAIN . WHILE SCHEDULING A REPORT AND AS OPTION AVAILABLE IN 4.0 LAUNCH PAD CAN HE SEND A MAIL DIRECTLY AFTER RUNNING REPORT. -
I am getting the below error while bringing up the Process Scheduler error
Hello ,
I am getting the below error while bringing up the Prcs Scheduler.
Cannot open message catalog TMADMIN_CAT
Starting Process Scheduler Server PSNT for Database FSUAT ...
NLS:4: Cannot open message catalog CMDTUX_CAT, set 1, num 752; check TUXDIR=C:\b
ea\Tuxedo8.1, LANG=English_United States.1252
INFO: BEA Tuxedo, Version 8.1, 32-bit, Patch Level 192
NLS:4: Cannot open message catalog LIBTUX_CAT, set 1, num 1571; check TUXDIR=C:\
bea\Tuxedo8.1, LANG=English_United States.1252
NLS:4: Cannot open message catalog LIBTUX_CAT, set 1, num 1570; check TUXDIR=C:\
bea\Tuxedo8.1, LANG=English_United States.1252
NLS:4: Cannot open message catalog CMDTUX_CAT, set 1, num 793; check TUXDIR=C:\b
ea\Tuxedo8.1, LANG=English_United States.1252
exec BBL -A :
NLS:4: Cannot open message catalog CMDTUX_CAT, set 1, num 820; check TUX
DIR=C:\bea\Tuxedo8.1, LANG=English_United States.1252
NLS:4: Cannot open message catalog CMDTUX_CAT, set 1, num 801; check TUXDIR=C:\b
ea\Tuxedo8.1, LANG=English_United States.1252
exec PSDSTSRV -p 1,600:1,1 -sPostReport -- -C psprcs.cfg -CD FSUAT -PS PSNT -A s
tart -S PSDSTSRV :
NLS:4: Cannot open message catalog CMDTUX_CAT, set 1, num 1685; check TU
XDIR=C:\bea\Tuxedo8.1, LANG=English_United States.1252
tmboot: NLS:4: Cannot open message catalog CMDTUX_CAT, set 1, num 827; check TUX
DIR=C:\bea\Tuxedo8.1, LANG=English_United States.1252
tmshutdown -y
NLS:4: Cannot open message catalog CMDTUX_CAT, set 1, num 753; check TUXDIR=C:\b
ea\Tuxedo8.1, LANG=English_United States.1252
NLS:4: Cannot open message catalog CMDTUX_CAT, set 1, num 916; check TUXDIR=C:\b
ea\Tuxedo8.1, LANG=English_United States.1252
NLS:4: Cannot open message catalog CMDTUX_CAT, set 1, num 907; check TUXDIR=C:\b
ea\Tuxedo8.1, LANG=English_United States.1252
NLS:4: Cannot open message catalog CMDTUX_CAT, set 1, num 936; check TUXDIR=C:\b
ea\Tuxedo8.1, LANG=English_United States.1252
NLS:4: Cannot open message catalog CMDTUX_CAT, set 1, num 948; check TUXDIR=C:\b
ea\Tuxedo8.1, LANG=English_United States.1252
NLS:4: Cannot open message catalog CMDTUX_CAT, set 1, num 775; check TUXDIR=C:\b
ea\Tuxedo8.1, LANG=English_United States.1252
Please suggest.Duplicate thread :
Re: I am getting the attached error while bringing up the Prcs Scheduler
Nicolas. -
Error while exporting/transporting the Business system from Dev to Quality
Hi,
We are getting the following error whil exporting/trsnporting the Business system from development(SLD) env to quality(SLD) environment. The error is
404 Not Found
The requested resource does not exist.
Details: Go to main page of this application!
We have followed the following procedure to export :
1. opened the business system.
2. Clicked on export option
3. tried to download
then we got the above error message.
Please provide your precious inputs to resove our problem.
Thanks
RameshGo through the following links for transporting XI objects.
https://service.sap.com/~sapdownload/011000358700001684302005E/HowToSLDandXI.pdf
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/0fa2c490-0201-0010-61b4-df12869c4753
ere's a good link for what you are looking.
Re: Transport design and configuration objects
Here are some blogs.
/people/sravya.talanki2/blog/2005/11/02/overview-of-transition-from-dev-to-qa-in-xi
/people/sap.india5/blog/2005/11/03/xi-software-logistics-1-sld-preparation
Pls reward if useful -
Error while writing to the database (PTRV_HEAD/PTRV_PERIO/Cluster TE)
Hi All,
At the time of creating a travel request, I am getting the following error :
Error while writing to the database (PTRV_HEAD/PTRV_PERIO/Cluster TE)
Please advise how to resolve this issue.
Regards,
Rahulsuch problem occor when u have not defined the number range
Set Up Trip Number Ranges
if the problems remaines after defining number range...keep check all transaction there may two three more numbers ranges has to define..
this prblem is only due to number ranges not defined by you.
Maybe you are looking for
-
Using a URL parameter in SQL Query
Newbie question... I have been developing a dashboard application, and I have been using input bind variables in the SQL. That all works fine. What I would like to do is to have a user go to a page via a URL with paramaters like this: http://atlas:77
-
Junk characters in etext report
Hi all, I have 3 data tables in my etext .rdf template .This telmplate is for eft format report. The output report for the 1st and 3rd data table is ok in terms of display ,but I get '????????????????' in my through my 2nd data table in the report ou
-
This issue has been raised few times before. I followed the solution to check in / check out workflow and made Title as optional column but I am not able to still solve the problem. I have list based on custom content types. Created very simple workf
-
PSE11/Pre 11 - invalid serial number
photoshop elements 11 and premiere elements 11 only lets me enter 29 of the 30 digit serial numnber and then tells me invalid serial number - have and "Activated" slip from Office Max that says is Activated with this 30 digit number
-
I have made a Simple Login Application, thats implemnent JAAS. My Applicaiton Authenticate the User Successullly, but not authorize. I am using MySQL (Database) Server: JBOSS 4.0 I have made Two Tables: 1: Login (with column username ,password) DATA-