Error with Core Center when switching users

I can't seem to get this worked out...
When ever I switch user accouts I get 2 error messages then a restart. The 2 errors that I get are:
Core center failed to load hardware monitor
& no hardware monitor then an unvolintary reboot...
Any suggestions??

only run CoreCenter with one user. The error message you get is the "2nd" CoreCenter failed to load when you're in 2nd user account, the "1st" CoreCenter is still running.

Similar Messages

System reboots when switching users.

I have looked through the boards and can't find reference to this problem.
When switching users in Windows XP Pro SP2, from a power user to my admin acct. the sys will reboot after core center loads. The other users are not looged off of XP by way of fast user switching.
If other users log on while the admin acct. is still active, no problem and I can also log back into the admin acct. w no problem.
Additionally when logging in to a non-admin acct. the following error messages appear.
Hadrware Monitor failed to load Drive 1 .... Invalid handle
(Core Center) No hardware Monitor .... Invalid handle
(VBIOS) FLASH_MMIO_MAP DeviceIOControl Error.
If the items are not connected please piont me to the proper forum.

First late me comment on what a great library this forum has. It would seem that most issues are covered and often repeated. Some time may be involved to find a solution, but hard work is it's own reward.
Looking through the threads I've seen several referencves to doing a clean install after installing a new MOBO. I have not done this yet. So I have prepared a slipstreamed Win XP SP2 CD (as suggested in the threads). Before I continue I have to ask for a few suggestions.
First-- I will be removing all attached components and periphials (video,sound and externals) withe the exception of the mouse and keyboard. I will set the bios to boot from the CD. So what I would like to know is if my HD config is acceptable and is there a preferred order to connect other devices after install and all updates?
The 20 gig HD has been reformatted (NTFS) in 2 partitions, Zdrive is 1500mb for swap/page file(as per forum). This drive wasn't doing anything on my sys anyway. I only used it to try linux and I didn't have the patience to figure it out.
After all drivers are installed is it possible to use the programs installed on the old drive, or should the be re-installed also. I can save all important data if this must be done (ie. saved games, documents, photos etc.).
Last this is a shared machine w/teens. I have been through a lot to eliminate and protect my self from adware/ spyware and will continue to do so. I would like to keep the user profiles (Power Users) so that games and other software can be used without needing the admin password. This may be off topic but any suggestions would be helpful.

Has anyone else had a problem with the audio not keeping up with the video when switching to full screen on YouTube?

Hi. I have a OS X Yosemite Version 10.10.1 Mac Book Air, Processor 1.86 GHz Intel Core 2 Duo.
Has anyone else had a problem with the audio not keeping up with the video when switching to full screen on YouTube?
The video starts out fine, but if I click on the expand icon in the lower right corner of the screen the audio won't keep up.
Refreshing the page don't help at all. In fact, nothing seems to help once it starts.
I did not have this problem at all using Mavericks. The problem started after installing Yosemite.
Any way to fix it?

only $99, i thought it was closer to $175.

'Interference' when switching users

I recently encountered this problem where, when switching users, the screen looks like TV interference for a split second instead of the cube effect. It doesn't always happen, just sporadically. After looking on the forum and contacting the helpline chat with the support team, the iMac was taken in and a new logic board fitted.
Upon returning home I discovered that it stills happens, still sporadically but it happens. This would seem to eliminate the fact that it could have been the start of the leaking capacitors as this is a brand new board ( I did check that it was different from the last one ).
I have also read on here that it could be a software issue in Tiger, as with others I don't recall it happening with Panther, but my mind might be playing tricks ?!?!
Has anyone come across this, gone through the same solution process, and still have the issue ? Have you come across a solution ?
Many thanks.

Just to be clear, I installed the 2GB of RAM the day that I bought my iMac and neveer saw the problem until just before my midplane failed. Given all the info about the industry-wide capacitor problem, I seriously doubt that the RAM is related to any of this, including the interference.
The midplane issue involves failing capacitors which could affect many parts of the midplane, including the video. The failing caps might be related to the video issue. All I know for sure is that I saw the scattered picture, then my midpplane went. After it was replaced, I didn't see it for a while, but it did eventually return with no other symptoms, so my assumption is that it is unrelated.

Have to reconnect to airport when switching users

Recently I set up my HP printer to print via wireless rather than USB connection.
Ever since then, if users are switched, or if the computer is waking for sleep, I have to reselect my airport network from the menu.
Under "Network" system preferences, under "Network Port Configurations," Airport is at the top of the list and is the only connection with a checkmark.
In the same preference pane, under "Airport", I have the following 2 options selected:
--Automatically join an open network
--Remember any network this computer has joined
Any ideas how to fix this? Basically just an annoyance at this point--it's not like it drops while you are using it.
G4 933 mhz Quicksilver Mac OS X (10.4.7) Wacom Intuos 2 tablet; Epson 2400 Photo; HP Deskjet 6840; LaCie 80gb D2 FWDV

Similar issue here - just tried it and i went into the PPPoE options and in there I had " Disconnect when user logs out" and "Disconnect when switching user accounts" checked - Unchecked both of those - hit apply and so far looks good.

T60 Trackpoint Scroll Disfunctional when Switch User

I've been experiencing the issue where if a single user is logged into XP, the trackpoint scroll feature works flawlessly, BUT, if you use the XP switch user function and have 2 people logged in at the same time, the trackpoint scroll feature breaks down and doesn't work right.
This is what I've found (short of re-booting the system): User1 logged on --> Switch User to User2, the scroll feature will work, BUT if you Switch User back to User1 the trackpoint scroll doesn't work anymore So, to get it to work right for User1 again, Switch User back to User2 and Logoff --> Log back in with User1 and should work again.
I've done all the driver uninstall/re-install excercises and have tried the native synaptic drivers too.... This just seems to be the way this works (unfortunately).
Ironically, my old T30 had seemingly the same hardware, but I never had this problem with it... it was seemless when Switching Users. Funny, I bought a ThinkPad T because I love the trackpoint... I wish they would get it to work right
So, anyone else experience this? Any fixes?

Hi,
If you are using WAD, u have options "Number of data rows displayed at once" and "Number of data columns displayed at once" in the web item properties of the Table web item. There you can specify the count u want. This will surely get u the needed output wherein u can just scroll down/up/right/left according to ur convinience.
Assign points if this helps u...
Regards,
Koundinya Karanam.

How to correct or fix slow imac on start up or when switching user. Blue Screen will stay on for 3-5 minutes.

How do I fix a slow imac on start up and when switching user? The blue screen will stay on for 3-5 minutes.
Thanks

How much free space do you have on your hard disk? And have you ever performed a backup & clean install after an OS X upgrade?

HT5439 Has anyone had the Network time and date error with Apple TV when traveling?

Has anyone had the Network time and date error with Apple TV when traveling?

Jasion,
Maybe a bit beside the question, but it is always recommended here to open/save from/to own hard disk, and to copy from/to networks and removable media. You may be lucky, at least for a while, but it is better to be safe than sorry.
In addition to the (far greater) risk of file corruption, some issues are mentioned here:
http://helpx.adobe.com/illustrator/kb/illustrator-support-networks-removable-media.html

O/C with Core Center won't save.

I am trying to o/c with Core Center utility, and it works quite nicely. However, the o/c session will not save. as soon a I restart, all setting are lost and I have to use Core Center to re- o/c. Are there any BIOS updates to fix this?
Thanks.

This is true...Core center...is crap. Don't use it. In fact, save yourself a few headaches by uninstalling corecenter altogether. Dynamic overclocking utilities, overall, are faulty. Corecenter is no different.

Error sound on mac when switching tab with cmd+right arrow

On Firefox 3.6.9 and OSX 10.6.4, when I switch to a tab to the right using cmd+right arrow, I get an error sound but Firefox successfully switches to the tab. The error sound is the same sound you get when you press a keyboard shortcut that doesn't exists (ex: cmd+?)
However, if I use cmd+left arrow I don't get the error sound.
How can I eliminate the error sound?

I am just finally posting a reply. Looks as though the sound card went out. I was told that I could purchase a new open and install myself. I did not do that, but rather my step-dad just decided it was time to buy a new Mac Mini.

Stor.e TV+ No Loader error keeps coming up when switching on

I have been experiencing continual problems accessing the hard drive. "No Loader" error message keeps coming up when switching on.
The so-called "solution" to this problem posted on this forum is to open up the box and fiddle with the cables. Whilst I have had some success with this method initially, dismantling the box 10 times a week is not on.
I tried something else in desperation.
When the No Loader message comes up, I switch the box off and on again from the remote.
After 2 or 3 times or so the HDD folder usually appears.
I have been doing this consistently now with great success. This however suggests that the No Loader error message is NOT a mechanical connector problem with the hard drive but (as usual) poor software (what else?).
Dismantling the unit is tantamount to switching it off for an extended period of time so may explain why this technique works.
Switching the unit on and off several times also solves the problem of the D folder not appearing on the network even though Win7 shows Store-TV-Plus as a mapped NTFS drive (but can't find the D folder).
See the similarity?
Another thing that exacerbates problems is the unit's poor ventilation. The first thing that happens with this unit is that the rubbish stick-on rubber feet fall off.
Whilst this may seem innocuous, the ventilation slots are underneath the unit and will be blocked if there are no feet. I live in a hot country so this device gets pretty hot and behaves even more erratically unless well ventilated.
Ideally keep it well away from other units and preferably sit it on a small box by itself with the vents underneath well exposed.
I also still experience problems playing FLAC and MKV files. The unit occasionally loses synch with FLAC files which generally otherwise play OK and locks up or causes loud bangs or white noise on the speakers (dangerous).
Some MKV files just don't play at all even though VLC plays them. There are a myriad other inconsistencies but these are the most annoying.
Is anyone else experiencing these problems or does anyone have any other solutions to prevent these problems?
I don't suppose we can expect another software upgrade from Toshiba? In your dreams, pal.

OK, so I took the risk and updated the firmware of my Stor.e TV+ to the Noontec V8S latest firmware V3.0816.13_V8S from noontec website.
The update went fine without a hitch (took about 2 minutes from an old 256MB flash drive plugged into the back USB port of the unit, which I formatted before using), and some of the irritating shortcomings of the Toshiba firmware was solved. Samba worked in some fashion, but I was still not able to download songs directly to the Stor.e over wireless, which is the only other feature I currently need. The irritating remote control buttons were changed to the way any sane person would use them (I had changed my universal remote control to correct this, so would have to change the settings if I kept the updated firmware) The new firmware seems solid, but I DON'T USE THE VIDEO CAPABLITIES, so I can't comment on this.
One major drawback of this update for me is that the small display on the unit becomes much less readable. Seems like there is a problem with the font on the new firmware. I use my Stor.e exclusively as a flac music player, and since I don't have it connected to a tv the small display is crucial for me to select tracks or disks. I have 300+ discs, so the Stor.e is an excellent cheap media player which I connect to my HIFI system via a DAC.
I thus had to change back to the Toshiba firmware to correct this problem. Seems like I would still have to use USB to download music to the Stor.e when I buy new CDs. What a pity.
Incidentally, the new Toshiba firmware is very much like the old firmware, in that it lacks the capability to switch on Samba. In the readme Toshiba states that the new firmware fixes a network problem, but I think that this is probably the smallest issue most users have with the Toshiba firmware.
So, my advice to anyone having video, control or other issues with the Toshiba firmware is to flash to the Noontec firmware to see if it resolves their issues. If it doesn't one can always revert to the official Toshiba firmware as I did.
You do this at your own risk though, if you brick your unit don't blame me...

Popup printing message when switching users

I'm giving my old Air to my brother, so I set up a new account for him. When I log in to the new account, I get the following message:
Failed to listen for incoming Popup Jobs. You will not be able to use Popup printing for the duration of this session. Please report this incident to a system administrator
It appears in a small window. Every few seconds, an identical window will come up; by a minute, the screen is filled with them!
A bit of Googling indicated I should remove Pharos software. I tried that--I looked in the appropriate library folder--and nothing was there. Also, this problem didn't exist on my old account. (Pharos doesn't show up in my login items either.)
Weirder still, if I restart the computer and choose my brother's account at the login screen, it opens error-free. But then, if I switch back to MY account without restarting, I get the same pop-ups!
It's a pain to have to restart to switch users. Someone please help!

Ok, so it turned out it was Pharos. At first, when I did what the post below said, I could not find the uninstaller. It turns out it's a hidden file. Tech support told me to open Finder, press cmd+shift+g, type /Library/Application Support/Pharos/Utilities and press enter.
This way, I did find the uninstaller. I ran it, uninstalling both components, and afterwards everything is fine.
https://discussions.apple.com/thread/1204540?start=0&tstart=0

DualCoreCenter error - "Dual Core Center does not support!"

Hi, just bought the insanely expensive MSI 8800 GTX Ulta OC (£457), which seems to ship with insanely cheap utilities.
I installed the Dual Core Center (after installing the 'latest' nvidia driver 158.22).
During the install, it insisted on a net framework 2 repair/uninstall for some unknown reason (I have net framework 2 and 3 installed - ie all latest xp patches) with no prior problems.
Anyway, I let it do the repair and install itself.
Now when I run the DualCoreCentre, it comes up with error msg: "Dual Core Center does not support!"
Can someone shed light on what that means please.
Thanks...

It means:
I suck, don't use me!
Stay away from MSI's utilities. If you want to overclock or control fan speeds or anything else.
Have a look through: here

Why does the screen background picture get reset to default when switching user

iMac with OS X 10.6.8
I have several user accounts on this iMac, each with a different wallpaper chosen from a common folder (library/desktop/nature) in the top level of the hard drive. (Which exists – can always reset background picture from this folder)
When I switch from one user account to another, the wallpaper picture, set on the previous login, appears for a moment and then is immediately replaced by the default blue.
This happens when switching from any user to another. I tried restarting the system but the problem is still there.
This problem just suddenly started and there have been no upgrades or changes to OS X.
Ideas appreciated!!

I've found the answer.
Today, the problem suddenly appeared on my other Mac, which made me look at recent apps..
I installed Team Viewer a month ago, (which is a great app apart from this) so quit it and removed it from the dock. Problem solved!!
The odd thing is that the problem appeared only after I had been using Team Viewer for some weeks.

Error with DateField fields when locale is set to French

Hi Guys,
I have the locale/language switcher turned on in my app def. When I switch the language to French and use the calendar popup (DateField) the date returned is in an invalid format e.g. '19-oct.-2008' The problem with the format is that there's a full stop after the month, which causes an error to be thrown when I try to save the row. Heres the error:
La valeur "19-oct.-2008" n'est pas une date valide. Exemple de valeur valide : "29-Nov-2005".
Where is this format stored? Is there a date pattern that is being used, such as in a property file? If it is being formatted programmatically where is this done?
Any help is much appreciated
Barry
JHS: 10.1.3.2.51
JDev: 10.1.3.2.0.4066

Hello,
The format is stored in your locale properties file generated by JHeadstart, and has the key 'datepattern'. The file is typically called ApplicationResources_fr.properties.
I guess someone accidentally put a . somewhere in that pattern, because (at least in JHS 10.1.3.3.85) the default datepattern for french is simply "datepattern=dd-MMM-yy" and works fine.
Regards,
Evert-Jan de Bruin
JHeadstart Team

Error with Core Center when switching users

Similar Messages

Maybe you are looking for