Errors afyer software update for my Z10
Right after software update for my bb z10, i can not opewn now setrings, notification and wifi. How can I fix this? Please help
I suggest you try the very clean and very forceful AutoLoader method:
http://supportforums.blackberry.com/t5/BlackBerry-10-OS-Device-Software/Upgrading-OS10-devices-using...
Beware that it is completely destructive...the device will be "like new"...no data, no apps, no accounts, etc. Be sure you take a full backup first, as well as make full manual documentation of all apps, accounts, configurations, etc. Sometimes a restore reintroduces the very corruption one is trying to eliminate, and manual reconfiguration is necessary.
You can also use this to fall back to a prior OS if you desire...you can install any OS level for which you can find an AutoLoader. (Hint...search over on the CB site!)
Good luck and let us know!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code
Similar Messages
-
Installation error in software update for xperia x10 (android 1.6 to 2.1)
i have installed pc companion 2.0 and followed all listed steps but the listed error message is the same ..i want to update my current and. OS to 2.1 firmware
Hi,
I noticed your post hasn't been answered. Have you now managed to update your X10 to Android 2.1 successfully?
If not, have you tried using the Update Service program instead of PC Companion? -
Software Update for Z10 messes up texting
Did the software update for my Z10 yesterday and now my texting doesn't work. This has happened before. Looking forward for when I can trade in all the Blackberrys in our household for a different phone!!! Too bad! I wanted to support Canadian made but it's **bleep**!!
I suggest you try the very clean and very forceful AutoLoader OS Reload:
http://supportforums.blackberry.com/t5/BlackBerry-10-OS-Device-Software/Upgrading-OS10-devices-using...
Beware that it is completely destructive...the device will be "like new"...no data, no apps, no accounts, etc. Be sure you take a full backup first, as well as make full manual documentation of all apps, accounts, configurations, etc. Sometimes a restore reintroduces the very corruption one is trying to eliminate, and manual reconfiguration is necessary.
You can also use this to fall back to a prior OS if you desire...you can install any OS level for which you can find an AutoLoader. (Hint...search over on the CB site!)
Good luck and let us know!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code -
Hello, I wanted to update my ipod touch 1st generation. The current software is 1.1.5. So I purchased iOS 3.1 software update for iPod touch (1st generation) and than I get an error so it did not upgrade. Can you help please?
I too had the same issue. This is how I resolved it http://www.parkhi.net/2011/12/error-8288-ipod-touch-upgrade-ios-31.html
-
what do i do after downloading iOS 3.1 software and "There was a problem downloading iOS 3.1.1 software update for ipod touch. an unknown error occurred (8288). Please check that the connection to the network is active and try again." comes up?
Hello, I hope by now you have resolved the upgrade issue, but if not, here is what I ended up having to do:
“SUCCESS!!! I took my iPod to a friend who is a computer programmer/genius. He turned off his wireless, hooked the ethernet cable directly into his computer, and the download went through without a hitch. YAY!”
Here is my original post explaining what I had already tried:
“Hi all,
I got an iPod Touch 1st gen for my youngest son for Christmas as a starter. It has the 2.1.2 ios on it, but after I paid for the upgrade to 3.1.1, I keep getting an error message (8288) saying there was a problem with the network connection. I have called customer service, and they suggested I try on a different computer, and if that didn't work, try connecting to a different network, and then trying the update. None of this has worked. It seems that tech support is clueless with this issue.
I have installed and unistalled iTunes 10.5, 10.3, 10.4, and now I am back with 10.5. I have tried looking up the issue from several search engines but no one seems to have a universal solution and I have tried several.
I really want to have this thing updated for himw hwne he opens it, but I am starting to worry that my purchase was a bust. I know this is the oldest version, but I don't want to buy a newer, more expensive iPod and him still not be mature enough to really take care of it. As I said, this one is a starter.
Can anyone help? Please?!
Thank you!!!
P.S. We have a PC, with Windows XP Home.”
Now, there seem to be a lot of different ways to solve the 8288 error, none of which are universal. Best of luck getting yours upgraded!
Tiffany
P.S. The post by Sparkhi is a link to his blog going into a long story about how he wanted Apple to pay him for “solving” the issue….the one that apparently has been solved by multiple solutions. I’m not trying to bash, it just bothers me that he put up this whole story and finally, at the very end of his blog post, posts his solution. -
The error
Therewas a problem downloading iOS 3.1.1 software update for ipod touch. an unknownerror occurred (8288). Please check that the connection to the network is active and tryagain.
Keeps coming up when I try upgrading iOs 3.1.1 software to my 8gb 1st generation iPod touch! Please help! I've looked at all other posts related and none helped.Hello, I hope by now you have resolved the upgrade issue, but if not, here is what I ended up having to do:
“SUCCESS!!! I took my iPod to a friend who is a computer programmer/genius. He turned off his wireless, hooked the ethernet cable directly into his computer, and the download went through without a hitch. YAY!”
Here is my original post explaining what I had already tried:
“Hi all,
I got an iPod Touch 1st gen for my youngest son for Christmas as a starter. It has the 2.1.2 ios on it, but after I paid for the upgrade to 3.1.1, I keep getting an error message (8288) saying there was a problem with the network connection. I have called customer service, and they suggested I try on a different computer, and if that didn't work, try connecting to a different network, and then trying the update. None of this has worked. It seems that tech support is clueless with this issue.
I have installed and unistalled iTunes 10.5, 10.3, 10.4, and now I am back with 10.5. I have tried looking up the issue from several search engines but no one seems to have a universal solution and I have tried several.
I really want to have this thing updated for himw hwne he opens it, but I am starting to worry that my purchase was a bust. I know this is the oldest version, but I don't want to buy a newer, more expensive iPod and him still not be mature enough to really take care of it. As I said, this one is a starter.
Can anyone help? Please?!
Thank you!!!
P.S. We have a PC, with Windows XP Home.”
Now, there seem to be a lot of different ways to solve the 8288 error, none of which are universal. Best of luck getting yours upgraded!
Tiffany
P.S. The post by Sparkhi is a link to his blog going into a long story about how he wanted Apple to pay him for “solving” the issue….the one that apparently has been solved by multiple solutions. I’m not trying to bash, it just bothers me that he put up this whole story and finally, at the very end of his blog post, posts his solution. -
I got Software update for iOS 6.1 ..
After installation - Phone shows message to connect to iTune,
I connect to iTune - I got message - iTune has detected iPhone in recovery mode. you must restore this iPhone before it can be used with iTune.
I click on Restore iPhone - it gives error
The iPhone "iPhone" could not be restored. an unknown error occurred (-1).
Not my phone is not working - Its dead - is show the screen - Connect to iTune.
Please help.
Thanks.Error 1 or -1
This may indicate a hardware issue with your device.
Follow Troubleshooting security software issues, and restore your device on a different known-good computer.
If the errors persist on another computer, the device may need service. -
Everytime I get to the end of the software update for OS X 10.8.2 it says an error has occured and then restarts the download.
please help me.Perform a Permissions Repair using Disc Utility...
Verify or Repair Disk Permissions
Then Restart your Mac.
Next...
Go here > http://support.apple.com/kb/DL1581 and Download and Install the Combo Update.
After a Successful Install be sure to Restart your computer. -
Everytime I get to the end of the software update for OS X 10.8.2 it says an error has occured and then restarts the download. I have also tried downloading from the website link provided in some other comments but it says image unmountable please help
Perform a Permissions Repair using Disc Utility...
Verify or Repair Disk Permissions
Then Restart your Mac.
Next...
Go here > http://support.apple.com/kb/DL1581 and Download and Install the Combo Update.
After a Successful Install be sure to Restart your computer. -
I was downloading the software update for ipod touch 2gen and after it was done downloading it showed that there was an error with my ipod and when i saw it was on the lockscreen loading. its been like this for 4 hours already
What did the error message say?
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
Software update for leopard graphics error
I'm trying to do a software update for Leopard Graphics Update 1.0 but after it installs and goes to restart, it says it cannot verify this update and to contact the software manufacturer...any body know what this update is about and why I would get this error?
Try downloading the standalone updater and reapplying the update.
-
why is it when i download the software update for iphone an error pops out when downloading is finish and processing file is being done...i've already tried several time but still the same result.
Disasble the computer's security software during the download and update.
-
Why when I get a software update for my MacBook Pro i click on it for some reason it never connects to the server I can never get my software update is anyone else having this problem? if so what do I do? i have the 2007 macbook pro Mountain lion 10.8.2
Start up from that Mac OS X 10.4 disc you have. Insert disc in optical drive and start up with the C key held down. On the first Installer screen, from the menu bar, under Utilities, select to run Disk Utility.
In Disk Utility, select your startup volume (usually "Macintosh HD") in the sidebar and go to the First Aid tab. Run Verify Disk. If it reports a problem, that may be the reason for your long-term difficulties. You hard drive volume has data corruption.
You can try Repair Disk in Disk Utility. However, it would be a very good idea to have a backup of the data on that disk, in case the attempt to repair makes the problem worse. -
When trying to load music from ITunes to my ipod I receive the error "The software required for the ipod is not installed correctly. Please reinstall itunes to install the required sotware"
What should I do to correct the error?For general advice see Troubleshooting issues with iTunes for Windows updates.
The steps in the second box are a guide to removing everything related to iTunes and then rebuilding it which is often a good starting point unless the symptoms indicate a more specific approach. Review the other boxes and the list of support documents further down the page in case one of them applies. The notes below the box include tips on removing troublesome components.
The further information area has direct links to the current and recent builds in case you have problems downloading, need to revert to an older version or want to try the iTunes for Windows (64-bit - for older video cards) release as a workaround for installation or performance issues, or compatibility with QuickTime or third party software.
Your library should be unaffected by these steps but there also links to backup and recovery advice should it be needed.
tt2 -
Software Update for Brother printers disabled my printer
This morning I installed a Software Update for Brother printers and now I can't print. Every time I try, I was gettting an error message that says some of my software is missing and it asked if I wanted to install it. A window opened looked like it was looking in Software Update and it didn't find any software. I deleted the printer in Printers and Faxes and downloaded the CUPS driver from Brother that says it's compatible with OS 10.7. Now I can't add the printer. When I go through the steps to add the printer, for Print Using I select HL-2140 series, which is the model of my printer. I click on Add and the Add Printer window starts looking for the printer software, but I think it's looking in Software Update. The message comes up "the software for this printer is currently unavailabe. Please contact the printer's manufacturer for the latest software. I did that, but how can I get it to use the driver I downloaded from Brother instead of looking for it in Software Update?
This helped with both my Brother printer and my HP AIO. I was having marginal printer function after installing OS X Lion, then replace the Airport Express with an Airport Extreme. That knocked out everything....After several days of loading and reloading programs in different permutations, this relatively simple step was the charm.
THANKS!!
Maybe you are looking for
-
Can I use my iPad (1st gen) with apple tv (2nd gen) for things such as air play and mirroring?
Can I use my iPad 1st generation on a apple tv 2 generation for things such as AirPlay and mirroring I'm thinking about getting a new apple tv but it's pointless if iPad doesn't mirror or AirPlay, cheers guys. I understand the 2nd generation works.
-
HP Laserjet 100 color MFP M175 PCL6
My printer worked fine connecting to the wireless network at home. We just moved to a new State and have AT&T Uverse and their modem and router. Cannot get the printer to connect to the router. Tried everything I can think of including installing
-
File-FTP command before message processing
Hi experts, my requirement is as follow : i have 5 files on my FTP server. All are named FILE_hhssmm.xml In the configuration of my CC out, i have put as specific file name to get picked 1*.xml I need a command line in the 'run operating system comma
-
Account Help. Can't use Apple ID
Hello. I am in a complete shambles over my Apple ID account as such I can no longer login to the community using it and had to create this account just to ask for help. Ok so my main issue is I login using my normal ID that I use on everything and th
-
Where's the best place to store email templates?
Hi all; In a web app I store all my email templates in a files folder in the web app. Can't do that with a worker in a cloud service - no files. So where's the best place to store them? In a BLOB? And if so, is there a way to have files in my project