Establish IP from DHCP but no Internet or Extremely Slow

Synopsis: Net Macmin, New Ethernet Cat 6 cable (approx. 90 ft), DSL Comtrend Router.  IP Connects, slow to no internet.
Added a 90' cable and ends across store basement from front PC to router in rear of business.  Standard non-crossover Cat 6 cable properly crimped.  Get IP Address from DHCP on front MacMini but internet is extremely slow.  I re-ran the cable away from parallel to power conduit, still extremely slow.  The light on the port which this cable is plugged in flashes at high rate with no pause, unlike three other connected to router.
Front MacMini works fine over wifi, but retail software recommended ethernet connection to ensure reliability should interference occur over wifi.  When I'm testing the Ethernet I do shut off the wifi and have, since started testing, changed the service order so wifi is second chosen to ensure tesitng with ethernet is accurate when wifi is on.
When you try to load a webpage (I used google) through safari it loads 25% of the load bar and stops until it times out a few second later.  Used network utility to verify connection to goolge, it took a few seconds longer than wifi but was able to ping google.  I don't own a ethernet tester and would rather not buy one for one project.
Based on the ability to connect with IP address tells me the cable is able to talk back and forth with the router, correct?  I've read a lot about ethernet port issues, how common is this, what else could be causing the problem?
Internet Source: MyFairPoint DSL for Business
Network Hardware: Comtrend AR-5381u DSL Router
Other Hardware on Router: Second MacMini, Dell Tower, Color HP LaserJet
Thank you to whomever can help and everyone that lends feedback!

My plan is to bring my MBP to the shop later this week to test this out.  I wanted to put this out there to see if any other troubleshooting ideas were brought up.  Thanks for the input!

Similar Messages

  • I have wifi connection, but my internet is very slow

    I have wifi connection, but my internet is very slow

    try switching off photo stream in System Preferences > iCloud
    This seems to throttle the internet connection and when I switched it off, it fixed my issues instantly!

  • My fios internet is extremely slow.

    My fios 50/25
    Only early in the morning, the internet speed is usable.
    The rest of the day, the internet speed is unstable.
    After dusk, i can't send emails with attached files like an image file.
    The connection is lost.
    I tested my internet speed as shown below.
    When I tested my internet speed from verizon, lot of time there was an error message that said 'test timed out'.
    I tried all the different servers.
    Sometimes the test is an success but the speed is very slow.
    I installed the optimizer tool and did all the other options like resetting the router, checking the wire, etc.
    I used the internet for over 15 years but I can't solve this problem myself.

    I'm having the same problem after dealing with support for about a month now with no resolution.
    It's likely a PON card issue and it's a task in and of itself to get the Network Engineers or Tier 2 guys to accept that it is an issue and to take the steps necessary to fix it.
    They will definitely wanna check the router, ONT, circuit, and other things first though so be ready for that.
    Forum support team has created a ticket with them and I'm still waiting to hear back.

  • Mirroring from mac(osx 10.8.2) extremely slow

    Hi there,
    Im having problems using Airplay from Mac. I have OSX 10.8.2
    Apple tv latest gen updated to the latest firmware.
    When i trying to activate Airplay on my macbook air (1.7 Ghz, core i5) it takes ages to stream it to the tv.
    Airplay shows that is active on the mac screen, but apple tv remains blank... then 5 min after i can see a fix frame ... etc...
    Simultaneously if i go to my Ipad (3rd gen), streaming videos and youtube works flawlesly, but if i try to mirror a game or try to play a song it get extremely slow....
    Any thoughts?
    My router is a Linksys E3200 and im using a 5ghz wireless network.
    thanks!

    hi everybody
    I really need some help so here is a little up !
    thanks !

  • Read from 16 GB Micro SD is Extremely Slow

    I have had a new Blackberry Tour 9630 equipped with v4.7.1.40 software and a 16 GB micro SD card.  Reading files from the card is extremely slow.  I first noticed this with video playback (extremely jerky and freezes) and actually replaced my first 9630 a few days after purchasing it. 
    I eventually gave up on video playback but now have very recently been using Media Manager to upload files (.jpgs) from the 16 GB micro SD card Media Card to my laptop.  The bottom line is it is taking 10-15 minutes to upload 13 .jpg's (total 6.7 MB) and is a major pain in the butt.
    Some of the trouble shooting steps I have taken:
    - moved same 13 files to main memory on Blackberry then uploaded to pc in 10 seconds
    - moved micro SD card to my son's Samsung phone - uploaded the 13 .jpg's from it to laptop in 10 seconds (so the memory card is good)
    - installed Desktop Manager and Media Manager on my desktop pc and connected blackberry to it - same poor upload behaviour from files on micro CD equipped on the 9630
    - checked on blackberry Doc ID: KB05461 at http://www.blackberry.com/btsc/search.do?cmd=displ​ayKC&docType=kc&externalId=KB05461&sliceId=1&docTy​... and it states: 
         BlackBerry Device Software version Media card size limit
         BlackBerry Device Software version 4.5.0.81 Up to 16 GB
         BlackBerry Device Software version 4.6.0 and later Up to 32 GB
    so I should be equipped with the proper software vintage.
    I am not sure what to do next and would appreciate any and all assistance/idea's etc.
    Thx,
    Gerry

    You can use a USB flash drive & the camera connection kit. First download the pics to your computer.
    Plug the USB flash drive into your computer & create a new folder titled DCIM. Then put your movie/photo files into the folder. The files must have a filename with exactly 8 characters long (no spaces) plus the file extension (i.e., my-movie.mov).
    Now plug the flash drive into the iPad using the camera connection kit. Open the Photos app, the movie/photo files should appear & you can import.
     Cheers, Tom

  • MBP 5.1 I have a recent problem with airport connectivity. ethernet connection is working fine, but wifi has become extremely slow and bad functioning. signal is received, no problem with the wlan (my husband 's wifi with MBP is perfect) please help

    I have a MBP 5.1 with snow leopard 10.6.8. It has been working fine until few days ago, when it started to have different problems:
    1) airport is not working well. it is extremely slow, has difficulties in fully loading pages, looses connectivity, It is not browser related, behaves thesame in safari or firefox; it is not the router/wlan; my husband mbp wifi works fine (as it was mine...) and iphone wifi is also working fine. it sees the signal and different networks. , it is also very very slow in opening skype (after that, it is working ok) if  I connect via ethernet cable to the same router, everything works perfectly and with the correct speed.could it be a damaged airport card? a software problem/corruption? logic board? (I hope not, the computer is out of apple care now....)
    2) after a certain time (more than hours) of use, the trackpad is behaving strangly, increase sensitivity to touch, unwanted selection of folders, files and text or images in web pages when i move the cursor, the cursor jumping all over the places while writing, ecc I have the impression it starts doing that when I use heavily the CPU ( and the temperature goes up). Is this again a problem of the mother/logic board?
    I had recently serviced it since it was not booting properly, but except some permissions repaired, they did noit find anything wrong in the hard drive (which I have  now substituted with a SSD) or other hardware.
    thanks in advance for any help/suggestions
    alessandra

    I think I solved the wifi connection problem, just by switching off completely the router! sounds trivial, but in this case it worked!!!
    the funny behaviour of the trackpad/cursor still persists. any suggestion???
    thanks again

  • Can't get any IP address from DHCP, but unattributed IP adress "already in use"

    Hello,
    I have a mac mini with a manual IP address (192.168.1.121) which connects fine to the internet through ethernet.
    When switching to DHCP instead of manual, no IP address is ever given to me (blank space after IP adress: in the network prefpane)
    however, I immediately have an alert popup that says the address 192.168.1.150 is already in use.
    I wonder where I could change this 192.168.1.150 address since I do not have this setting at all on this machine on any Network Port, not in Airport and not in ethernet. (I have no other network ports)
    How can I change a setting that I didn't make in the first place?
    The console reports the problem once every second also, and there is quite a general slowdown and beachball because of this.
    I tried to renew DHCP lease but it stays blank too.
    I also try to delete ethernet interface, and trash the Network configuration in the general Library, reboot, recreate it but the problem remains.
    I also have reinstalled Snow Leopard and applied updates with no better luck.
    Thank you very much everyone if you have a clue.

    When you changed the setting to DHCP, did you click the Apply button? Also, you need to restart after changing from a manual IP address so the router can assign an unused address to the Mac when it detects it during startup.

  • RT61, connects, gets ip from dhcp but no traffic gets trough

    Here we go again. I bought D-Link DWL-G630 wireless pcmcia card which has RT61 chipset. I installed latest rt2x00-cvs and rt2x00-rt61-fw from core. My network manager sees wireless networks, I can connect to mine (WPA2 AES) I even get ip from router. Link light is on and act light blinks everytime when I try to ping. Modules seemed to load automatically, lsmod sees rc80211_simple, rt61pci, rt2x00pci rt2x00lib, mac80211 cfg80211 eeprom_93cx6. dmesg tells about succesful authentication and association. Only weird thing I can see is Bit rate=1Mb/s even though link quality = 60/100. I dont have any iptables stuff in use. I cannot even ping my gateway.

    Hi Alain,
    Seems my router has no option for router traffic
    ip inspect name REMEMBER       bootpc ?
      alert        Turn on/off alert
      audit-trail  Turn on/off audit trail
      timeout      Specify the inactivity timeout time
    But i applied ACL on inside to allow
    permit udp any any eq bootpc
    that fixed the issue.
    Many thanks for answering the questions and letting me know about router traffic option.
    Regards
    MAhesh

  • I purchased a season of a tv series from ITunes, but my IPad will not slow it to download.  Help!!

    I purchased a season of a TV series from ITunes and my IPad will now download.  What should I be doing to make this work?

    Hey Sue,
    You can download those TV shows from the iTunes app on your iPad, just following the instructions in the following article.
    Downloading past purchases from the App Store, iBookstore, and iTunes Store
    http://support.apple.com/kb/ht2519
    Thanks for using Apple Support Communities.
    Regards,
    -Norm G.

  • How can I get Apple to send me the OSX10.7 disc? I'm deployed to Afghanistan and need to reinstall my OS but the internet is too slow.

    Does Apple have an email address for support questions?

    Try:
    You can purchase Lion by contacting Customer Service: Contacting Apple for support and service - this includes international calling numbers. The cost is $19.99 (as it was before) plus tax.  It's a download. You will get an email containing a redemption code that you then use at the Mac App Store to download Lion. Save a copy of that installer to your Downloads folder because the installer deletes itself at the end of the installation.
    The problem will be if Apple will ship anything to Afghanistan. You are better off trying to download it.

  • Airport Extreme (time capsule model) internet speed EXTREMELY slow.

    Hello, first thank you for any help on this as it is a bit frustrating for me.
    I recently noticed my internet speed was running significantly slower on both my MacBook Pro and on my wifes MacBook.
    I had my ISP come and check out the problem. They hooked my MacBook Pro directly to the modem and my speed went from under 1 mb to over 5mb.... he then had me hook up directly to the lan port on the airport extreme and my speed was once again back down to the 1 mb range. He concluded that it must be a problem with the speed once it hits the Airport Extreme.
    He ended up giving me a different modem, its a 2wire wireless. I have since connected my airport extreme to the new modem and am still pulling down the same speed, but now I have connected directly to the new 2wire wireless modem and am getting my 5 mb speed.
    Can anyone give me any help or advice on what I can do with my airport extreme time capsule so that I can get the speed I should be getting from it.
    Thanks again.

    More information. I have a separate router for ISP connect/DHCP. I only use my Airports to create a WDS and bridge onto my home network. I have never allowed 2.4GHz or 5GHz phones in the house, just to limit interference. I live way out in the country so interference from neighbors is negligible to nonexistent. Speed testing done with Speakeasy.net/speedtest
    I moved all the hard wired machines from the TC to my switch. Which will impact the speed of my backups, but it helped with internet throughput for those machines.
    Then I split my WiFi into 2 separate nets, each with a connection to my home network switch. I created a b/g network with my ufo Extreme and my Express (NET 1). I left my TC set for n/b/g (NET 2). As long as my MacBook was powered off internet speed were nice and fast. As soon as I turned on my MB the speeds were impacted, not as bad as before.
    I then changed NET 2 to be n-only 5GHz and retested. These was a small but noticeable impact for wireless machines but I have concerns because my ISP is wireless and runs at or near 5GHz.
    I then changed NET 2 to be n-only 2.4Ghz and retested. Again a small impact for wireless machines whenever my MB was connected to NET 2.
    I then had my MB join NET 1 and speeds were nice and fast all around. My solution, shutdown the wireless on my TC and use it as just a network drive while I use my old reliable b/g hardware for WiFi.
    Maybe someday this Draft version of 802.11n will be finalized and have no issues.
    Message was edited by: Gregory Daniel

  • Internet connection extremely slow in most applications

    I have an aluminum iMac 2.4GHz. I also have an iBook G4. Both are on the exact same desk and connected to my universities internet connection.
    The iBook can surf the internet fine, as well as download software updates with no problems. However, the iMac takes soooo long to open a webpage, and can only do it on half of the attempts. Using Software Update is a joke because it takes 5 minutes to download a megabyte, and then times out. Mail also has problems.
    Stranger still, when I finally get to a download page to download some freeware, the download happens at normal speed.
    When I restart in Windows XP, I can surf the net just fine and install updates and check mail.
    I have opened Network Preferences on the iBook and iMac to compare, and they both have almost identical settings. Maybe this is where I need to look for the problem.
    What can I do to solve this problem?

    I have very little experience with wireless authentication protocols, so my answer is intentionally vague - hopefully someone can get you a better answer.
    TTLS and PEAP are different authentication protocols used with wireless connections.
    The first thing I'd try is to get to the network settings and try to change the iMac to use TTLS for authentication.
    The WINS servers are kind of a strange happening...those settings will typically come from a DHCP server, is it possible that your iMac is holding on to DHCP settings from a different segment of the network you're on - have you tried renewing the DHCP lease (probably won;t help, but, you can try)
    Jeff

  • After installing ios 8.0.2 internet is extremly slow and doesn't work at all half the time. I have done several reboots when it got stuck again. The touchscreen does only sometimes work on safari, half the time I can't navigate and cant open new tabs

    IOs 8.0.2 internet stuck and no touchscreen

    The following has gotten good results from users here ... a reset to factory default condition ...
    Back up and Restore your iOS Device with iCloud or iTunes
    http://support.apple.com/kb/ht1766
    iTunes: About iOS Backups
    http://support.apple.com/kb/ht4946
    Use iTunes to Restore your iOS Device to Factory Settings
    http://support.apple.com/kb/ht1414
    Here's someone who posted his results ...
    keithfrommariettaOct 12, 2014 3:25 PM Re: IPAD2 very slow after IOS 8 upgrade
    Re: IPAD2 very slow after IOS 8 upgradein response to pacoKAS
    SOLVED:  IOS 8 Issues on iPad 2:
    I just returned home from a visit to the Genius Bar. Like you and many others, when I upgraded my iPad 2 to IOS 8, it became practically unusable. It was VERY slow, lagged whenever trying to to do anything. Lots of screen freezes and apps spontaneously crashing. I was convinced that the processor on the iPad 2 just couldn't handle the new IOS and I went in to see about restoring to IOS 7.
    Thankfully, I was hooked up with a very sharp guy at the bar. The problem is not with the OS, it is with it being an *upgraded* OS. He used the analogy of when you had an older Windows computer and how over time (and over upgrades), they just tended to get slower and slower because of all of the garbage that was carried forward in the upgrades. At those times (and if you've ever had a Windows computer, you get this), the only thing that would speed it up would be to wipe the machine and do a fresh install of the current OS and then reload your apps, and the viola, everything would be fast again. Well, it turns out that IOS can suffer the same problems.
    THE FIX:  FIRST, be sure you have a current iCloud backup of your device.  Connect your iPad to a computer that has a clean fresh copy of IOS 8 on iTunes (this is best done with a computer other than the one that you sync your device to because you DO NOT want to restore it from a back up just yet). Ideally, if you do this at an Apple store you'll be assured of the right version there and someone to answer any questions you might have along the way. You then hold the power and home button down to hard-reset the device and continue to hold them down until it reboots into recovery mode. You then follow the instructions on the computer to reinstall the OS on the device (which wipes everything from it and then reinstalls a clean copy of it). Once this is done (which only takes about 15 minutes), your device will reboot and ask you to set it up. Answer the questions about language, location, etc. and continue until it asks you to log into your iTunes account. Once you do that, it will ask if you want to either 1) Set it up as a new device, 2) Restore from iCloud, or 3) Restore from iTunes. Choose (2), restore from iCloud. This will ensure that it brings down "clean" copies of all of your apps and preferences rather than the potentially corrupted ones that might reside in your iTunes backup. That's it! It will take a few hours depending on how much data and apps you have, but I am happy to report that my iPad 2 is now running IOS 8 and it's running as fast as it ever did when it was brand new!
    To sum it up, this process 1) Wipes your device and the garbage causing your problems, 2) Loads a clean and bug-free version of IOS 8 to your device, and 3) restores your apps and data so that it looks just like it did before the wipe, with the exception that it works now!  :-)
    Note also that by following this process you don't have to go through the painful and laborious process of reloading all of your apps, data and/or settings. iCloud takes care of all of that for you.

  • Totally frustrated - Internet moving extremely slow since update

    Just started happening recently out of no where - I browse with Safari - but just realized it also happens with Firefox - takes forever to open a page - and forget it if even the simplest of multimedia, like pictures, happen to be on the page - for example a simple imdb.com page - and if i go to YouTube to play a simple 5 minute movie - well i can't wait long enough for it - could be twenty minutes before the thing will actually play without stopping every two seconds.
    I feel like this started happening ever since I did my last updates which was for Safari... It is usually always something like that, being that once I installed a quicktime update, and all my videos lost audio - It was crazy. I thought updates were supposed to help! And apple does nothing about this stuff.
    I have already "emptied the cache", "reset safari", and "repaired disc utility' - to no avail I should not have to be doing a ton of other stuff, and finagling with my computer in areas i shouldn't be, and don't understand, just to fix something that an update from Apple has upset. So frustrating!

    Hi Eww - Thank you...
    Sorry, I thought I did say the update I did was "Safari" - Safari 3.2 to be exact on Nov 19th. This only started happening right after, that I know... And I am finding around the internet the same problem with no resolution. People noting a very similar problem since doing an update, some having done the most recent one (this very week's update which I don't even want to go near now), with more devastating results:
    http://discussions.apple.com/thread.jspa?threadID=1804312&tstart=0
    http://discussions.apple.com/thread.jspa?messageID=8530167#8530167
    I agree that it shouldn't be effecting Firefox - but it is... I don't claim to understand how that would work, but if things always made sense, we wouldn't constantly be needing to find "third party" fixes to things...
    My hard drive is just above 100 GBs, and about half remains. no huge storage files have been adopted... I have not changed any network settings. I get a strong wireless signal, however, I am not sure what you mean by running OS X maintenance tasks- Could you please advise?
    I have cleared the cache, reset safari, and repaired permissions on the HD...

  • Internet running extremely slow/hanging up

    My mac is running extremely slowly while connected to the Internet. It sometime will get to a site and sometimes will hang up and time out. I have an older pc also connected to this wireless connection and it is running very sluggishly too. Can anyone help me? This computer is about a year old and I dob't know enough about it to try and fix things on my own. TIA!!

    I am having the same trouble with my Mac. Once I am logged onto Firefox it is generally O.K. but if I leave Firefox and later try to connect again it won't load and I have to shut down the computer and restart in order to get back on the internet.
    Help!!!

Maybe you are looking for

  • Can we use Evaluate Function in Dashboard Prompt

    Hi Can anybody tell me Can we use Evaluate Function in Dashboard Prompt. If yes...How Thanks in Adv

  • Getting error while running form migrated from 4.5 to 6i

    I have a form built in 4.5. I have open that form in 6i and compiled it. Generated the fmx out ofit. but when I run that form then it gives me an error : frm40735:pre-form trigger raised unhandled exception ora-01403 Could any one please help me out

  • Close Functionality in an iview

    HI,    i have  an iview which i was opening as an external vindow. now my issue is need to close this iview using a close button. can any one

  • Set width of custom control

    Hi all I have a cl_gui_custom_container in a dynpro. I would like to manage width of it. I tried to use method set_width, but it does not wrk. I try the get_width and it works. What am I missing? Is it possible to achieve width management? thanks Gab

  • I can't open my power point document

    I am unable to open a pp document I have saved.  The few times it opened yesterday, it took at least 5 minutes to open.  The other power point documents I have can open with no problem.  I have also noticed that my computer is running very slow these