Establish Wireless network between Cisco857W and Linksys AP

Hi
I would like to know if it is possible to establish a wireless network between Cisco 857W and others AP vendors.
The goal is to extend the Wireless network provided by the Cisco 857W to others vendors APs.
Thanks in advance for your cooperation,
MP

Hello,
Thanks for the post. On this one, I would recommend the following steps pasted in the links below. Good Luck!
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02911238&cc=us&dlc=en&lang=en&lc=en&product=365...
I worked for HP but my posts and replies are my own....Thank you!
*Say thanks by clicking the *Kudos!* which is on the left*
*Make it easier for other people to find solutions, by marking my answer with (Accept as Solution) if it solves your issue.*

Similar Messages

Wireless Bridge between WAG120N and E1500

I have my internet coming into my WAG120N and going out wirelessly. I want to setup a wireless bridge between this and an E1500, so I can connect my TV to the E1500 (via an ethernet cable) and have it access the internet. Unfortunatly I can run a cable from the WAG120N to where the TV is. So it I can get the E1500 wirelessly bridged to the WAG120N, I hope I can get around this issue.
I have updated the firmware ont he E1500 to get Bridging support, but from what I can tell it only provides bridging via an ethernet cable. Is there away to bridge wirelessly?
Cheers
Mike
Solved!
Go to Solution.

1. Linksys wireless routers don't support wireless bridging.
2. Either install 3rd party firmware like dd-wrt or tomato or buy a dedicated wireless bridge and connect the E1500 to the bridge. That way you can also use the wireless in the E1500 for wireless connections.
3. Otherwise check power line ethernet. That's often a better and more reliable solution.

I have two facetime users, both connecting to our enterprise wireless network (Cisco WCS) and they can't make a facetime connection from IPAD to IPAD. Are there any apple protocols or other settings that need to be enabled on WCS? No firewall involved.

I have two facetime users, both connecting to our enterprise wireless network (Cisco WCS) and they can't make a facetime connection from IPAD to IPAD. Are there any apple protocols or other settings that need to be enabled on WCS? There is no firewall inbetween the two connections, as this is all on our internal network.
Both devices can connect to the network, but when they try to talk to each other they can't make the connection.
Thanks.

If anyone ever comes across this and has the same issue, here's what I did to fix it:
My Linksys router has a Network Mode setting, and I had to change it from "Mixed" to "Wireless-G only". (I would've used N but one of the NICs in my house is too old to support it.) Anyway, after making this change, Facetime works fine on the phone. Hope this helps someone else!

How can I rename an established wireless network using airport extreme?

How can I rename an established wireless network using airport extreme?

Thanks for the info. On your Mac......
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click on the picture of the AirPort Extreme
Click Edit in the smaller window that appears
Click the Wireless tab at the top of the next window that appears
Edit/backspace out the Wireless Network Name and type in a new name that you want to use
Click Update at the lower right of the window
Wait a full minute for the AirPort Extreme to restart
Close AirPort Utility
The new network that you named will use the same network password that you set up originally.

I installed my new Apple TV and successfully completed the configuration (Wireless network, Apple ID, and others) yet I am always in the Computers and Setting page- can't move to the main page – any idea on what and how, please?

Hello, I installed my new Apple TV and successfully completed the configuration (Wireless network, Apple ID, and others) yet I am always in the Computers and Setting page… can’t move to the main page – any idea on what and how, please?

Welcome to the Apple Community.
Unfortunately, a number of users appear to have encountered this problem. Some of these users have reported that the problem just disappears the following day or shortly after. Other users have found various other solutions to this problem.
Firstly, are you receiving any date and time errors when you turn on your Apple TV?
Check that you are properly connected to the Internet, by ensuring that you have a proper IP address and not one starting with 169. Also check that your location for the iTunes Store is set correctly, if so you might try changing it and then changing it back.
If the problem persists try restarting the Apple TV by removing ALL the cables for 30 seconds, or resetting it using the reset option under general. You should also try restarting your router, or if this doesn't work you might like to try a restore.

How to establish the connection between crm and r/3

Hi,
Sorry for posting this question in this forum, i did not find any CRM forums.My question is,How to establish the connection between CRM and R/3...in my office i installed standard alone CRM system,but it is not talking to R/3.
Could any one tell me where to find adapters and plugins for this.
Thanks in advance.
Ajey

Hello Ajey,
in the case you mean the connection between R/3 and SAP CRM you should read the Best Practice Guides:
B01: CRM Generation
C71: CRM Connectivity
B09: CRM Replication
from http://help.sap.com/bp_crmv240/index.htm. There is a CRM Forum at http://www.sap.com/community/ and also at http://www.sapfans.com/.
Regards
Gregor

Encrypting network between computer and printer

I would like to encrypt a network between computer and printer but I see references to ASCII and hexadecimal which I don't understand. Please can anyone explain in simple terms how to go about this?

The picture you showed is the settings for a WiFi network. There are four main types of encryption 40bit WEP, 128bit WEP, and WPA or WPA2. (I am ignoring WPA2 Enterprise as it is unlikely the printer is capable of this.)
WEP and WPA and WPA2 have all been cracked although it is still the case that WPA2 is better than WPA which in turn is better than WEP. On that basis while using eny of these encryption schemes is better than nothing if you are really concerned with security you would be better using an Ethernet cable.
WPA2 Enterprise is still somewhat secure but as its name suggests is not general suitable for home or small office setups.
With regards to ASCII and Hex, WEP passwords can be entered in either style, they would in fact be the same just entered differently. It is possible to convert an ASCII value to Hex and vice-versa.

Establish the link between equipment and its standby equipmnent

Dear experts
How to establish the link between equipment and its standby equipmnent in SAP?
For example, I have one pump in a plant and also i have a standby pump installed next to it...now i would like to establish a relation between these two inorder to track them.
I tried linking them as subequipments, but logically that is not sub equipment.
what is the best way to do it?
Regards

Praveen,
Equipment & Standby equipments are installed on same Function location.
There are below workarounds for solutions.
1. Use Position Number
2. Use A,B,C indicator with Running & Standby status
2. Use link if it is applicable.
3. Use classification system & provide characteristic as Running / Standby
Further u can assign the System condom which is equivalent to equipment running or stop condition during transactional data creation like order..
If it is running it indicates it is working.
If it is in stop condition then at that time it is in standby mode.
Thanks,
Ramesh

I want to increase my wireless network coverage upstairs and to the other side of my house. I have an airport extreme down stairs, can I get another one upstairs and hard wire it in?

I want to increase my wireless network coverage upstairs and to the other side of my house. I have an airport extreme down stairs, can I get another one upstairs and hard wire it in?

Yes.
It has been covered recently. I as interested in same question matter of fact but I will have to look up details or you could search.
Bob Timmons has contributed to this question so look his up and find it as well.
See this link;
https://discussions.apple.com/message/18017606#18017606
Also this;
https://discussions.apple.com/message/18077215#18077215
Message was edited by: WilliamNewMart, to add links and correct spelling.

Establish a wireless network between Photosmart C4385 and a Mac

I have a Photosmart C4385 All-in-One that I'm trying to use wirelessly. I have a MacBook Pro running OS X 10.7.2. I have a ubee wireless router.
I keep finding information saying that I need to run the "wireless network setup wizard" but I can't find it. I tried to use the different diagnostic utilites that HP suggested but they were only for PC, but the printer came with a Mac that I bought a couple of years ago. I have a new computer now and I'm just trying to get it setup to print wirelessly.

Hello,
Thanks for the post. On this one, I would recommend the following steps pasted in the links below. Good Luck!
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02911238&cc=us&dlc=en&lang=en&lc=en&product=365...
I worked for HP but my posts and replies are my own....Thank you!
*Say thanks by clicking the *Kudos!* which is on the left*
*Make it easier for other people to find solutions, by marking my answer with (Accept as Solution) if it solves your issue.*

Can't establish wireless connection between the printer and computer.

I recently upgraded my wireless to an Apple AirPort Time Capsule. I'm able to set up the printer via USB cable. And I'm able to set up the printer on the network via the Airport WPA utility. However I cannot establish a wireless connection between the computer and the printer. When I go to the printers window in my system prefereces, there is no wireless printer available to add in the "available printers" menu. Only the USB version printer is listed and of course when I disconnect the USB cable it shows as offline.I've tried all the fixes on HP's support pages. I've tried reinstalling the printer on both the router and the computer numerous times. The only thing I haven't done is reinstall the printer using the "Install Wizard" software that is supposed to come with the printer - (mine never came with it in the first place and of course HP doesn't have it available for download). And when I reset the printer to factory settings, then connect it to the computer via the USB, there is no installation software that pops up. Cant even find the **bleep** thing in "Finder". (I'm assuming that it should show up as some sort of external device.) I've checked to make sure both computer and printer are on the same network. (sometimes my computer will grab a connection with the next nearest network.) I've checked all the settings for the printer via the HTML configuration utility. I've even updated my Macbook software and restarted it multiple times. Note: the printer actually worked for a bit when I first switched routers, but the printer's wireless function went offline several times and then quit altogether. Really frustrated that I bought another HP product thinking this time things would be different. HP is no help unless you want to pay $$ for a phone call. I'm about ready to take this thing out in the desert to use for target practice and never buy another HP product ever again.

Hi , I saw your post regarding the problems you are having with your LaserJet Pro P1102w Printer not showing on your Macintosh computer. I may have found some resources for you.
I have a few questions for you, so I can offer some additional assistance:Before you upgraded to the Apple AirPort Time Capsule, was the printer working wirelessly without any issues?
When you say; 'I reset the printer to factory settings', how where you trying to do this?
I found some instructions from this post: How do I reset my Laserjet p1102w to its defaults, copied here for you:
To restore the printer back to factory settings, turn the printer off, hold down the wireless button and the cancel button (x button) then turn the printer back on and don't release the two buttons until the printer stops making noise. (When they say turn the printer off, I think they mean unplug the power cable.)
"I've checked to make sure both computer and printer are on the same network." Do you know if you are able to access the printers Embedded Web Server (EWS)?To access the EWS - Make sure that the Ready light () is on and that the printer is idle and silent.Press and hold the Cancel button (), and release it when the Ready light () begins blinking.The configuration page prints.Type the IP address or host name of the product in the address field of a supported Web browser, and then press Enter on your keyboardLet me know if this page loads
To answer a few more items you have listed:... When I go to the printers window in my system preferences, there is no wireless printer available to add in the "available printers" menu.This could be an issue with your print system, I recommend resetting the printing system and then Repair Disk Permissions - after that try to add the printer again.
... the "Install Wizard" software that is supposed to come with the printer - (mine never came with it in the first place and of course HP doesn't have it available for download)HP provides their software/drivers to Apple to be released through your Apple software updates. You can review this document on how to Install a Mac Printer Driver Using Apple Software Update. Which leads into your next point...
... there is no installation software that pops upWhen you connect the USB cable your mac may still recognize the printer software as being already installed - check for apple updatesOn the Mac, click the Apple menu (), and then click Software Update, or click About this Mac, and then click Software Update. A list of available updates displays.
... Not seeing the printer in "Finder" From what I understand most printers will not show in Finder unless you install a memory card into a supported port on certain printer models, only then will it read it like an external device. A few more things you can check are that the new settings in the Apple AirPort Time Capsule are setup to allow the printer to communicate. There are several of these settings listed in this document; Tips and Workarounds for Common Wireless Network Printer Issues. HP regularly releases firmware updates that may also correct the problem you are experiencing. You can click on this link to Getting Printer Updates for HP LaserJet Pro P1102w Printer. I did find 2 more documents that may offer some additional information as well;HP LaserJet Pro P1102w Printer - Connecting the Printer After Changing Your Wireless NetworkAn 'Unable to Find Printer' Error Displays for the HP LaserJet Pro P1102w Printer Please let me know if any of these steps resolved your issue, or the details of what happened. I look forward to hearing from you, hopefully with good news! Thanks,

Help! Making a Wireless Network between a PC and Mac and more.

I am trying to make a network between my powerbook and my fiance's pc, so we can share printers. I have an Airport Express and I bought her a Netgear Wireless PCI card. The PCI card is installed and has located the Aiport network. How do I get it to see the printer attached? Is Bonjour necessary? I'm downloading it via the Mac and then transferring the file by Zip because for some reason it wasn't downloading properly on the PC.
Also of note, we use dial-up to connect to the net so this network is again just to share the printers we have, and maybe files.
Printer sharing: I have my HP deskjet connected via a 4-port hub to my Airport. My computer recognizes the HP but when I connected the Lexmark 2250 it couldn't see it at all. Why is that? What can I do to fix it? I have the latest Lexmark Drivers.
How do I get my Mac to see the PC for file transferring, etc? I've been searching through apple's site for information and nothing is really helping me. I am gonna explode.
Any help would be greatly appreciated.
Thank you in advance.
Seth

Ok I got the PC to see my HP 940c wirelessly using Bonjour. However, I still can't get the Lexmark 2250 to show up on either the mac or pc wirelessly when connected to the hub? Is using a 4-port hub connected to the Airport express just not going to cut it for making a multiple printer hub?
I'd really like to do this plus make an network between the two computers.

Using exisiting wireless network SSID name and settings

I want to use an existing wireless network SSID and settings as i setup my new airport time capsule. I plan to turn off the wireless network at the Westell modem/router that now establsihes the network. what setting do i pick in airport utility? : extend a wirless network or steup a new wireless network?
When should i turn off the wirelss at the Westell router? Before or after running airport utility?

Establish a permanent Ethernet cable connection from one of the LAN <-> ports on the Westell router to the WAN "O" port on the Time Capsule.
Configure the Time Capsule to "create a wireless network" using the same settings for the Time Capsule network as the Westell.
Make sure that the Time Capsule has been configured to operate in Bridge Mode to work correctly with the Westell router.
Once you have the Time Capsule set up and working, you can turn off the wireless function on the Westell router.

Wireless connection between computer and HP Officejet 6600 e-All-in-One Printer.

I just bought an HP Officejet 6600 e-All-in-One Printer - H711a. I want to have a wireless connection between my computer and my printer in order to place the printer in a different room. The instructions say that I need to give the name of my wireless network. Do they mean that I need a wireless internet connection? I absolutely don't want to go wireless on the internet. How do I go about this?

Replacing your wireless router now try.
http://www.hp.com/global/au/en/wireless/reconfiguring-system-help3.html
Say thanks by clicking the Kudos Thumbs Up to the right in the post.
If my post resolved your problem, please mark it as an Accepted Solution ...
I worked for HP but now I'm retired!

Wireless network between mac + PC keeps failing to connect.

Both of my computers my Macbook and my HP PC are connected on the same wireless internet connection with the same IP address the same server name and everything. I have been through both devices and enabled every sharing setting could find and think about.
I need this wireless network to get printer sharing online. as the PC has the printer connected via USB to it. If anyone can assist please do.
Thanks,
Connor.

Ok I got the PC to see my HP 940c wirelessly using Bonjour. However, I still can't get the Lexmark 2250 to show up on either the mac or pc wirelessly when connected to the hub? Is using a 4-port hub connected to the Airport express just not going to cut it for making a multiple printer hub?
I'd really like to do this plus make an network between the two computers.

Establish Wireless network between Cisco857W and Linksys AP

Similar Messages

Maybe you are looking for