Ethercat connection between windowsPC an third party device.

We want to create an ehtercat connection between a windowsPC an a frequency converter from Stöber(company).
The connection has not to be real-time capable.
Is this connection possible without buying any third-party drivers?
rgds Reinhard

Hi Reinhard,
Our EtherCAT driver only works for our Real-Time targets. Unfortunately, there is no Windows solution for NI-Industrial Communications for EtherCAT.
Matt S.
Industrial Communications Product Support Engineer
National Instruments

Similar Messages

Extending wireless LAN using third-party devices?

I know that with multiple Airport Extreme base stations, it’s a simple matter to extend the range of an 802.11n network by using the “Extend a wireless network” or “Participate in a WDS network” wireless modes. It seems like of the two, “Extend a wireless network” might be the easier of the two to configure. Does anyone have recommendations / preferences between the two modes?
Separately, although I can afford Airport Extreme stations personally, I have friends with the same desire to extend their existing wireless network but who can’t afford Airport Extreme stations. Is there a lower-cost way to do this with Netgear, D-Link, or other third-party devices? Does this mean all of the devices must support WDS to work, or are there other solutions? Do you have recommendations for specific models that work well for extending networks (preferrably also models that support WPA/WPA2, and not just WEP).
Any help would be appreciated. I won’t go into the details of the distances involved or intervening walls. Let’s just say a hop or two should stretch the distance.

Bob Timmons wrote:
"Extend a wireless network runs at "n" wireless speeds with minimal bandwidth loss on the network
WDS runs at "g" wireless speeds, even if you are using newer "n" devices. The bandwidth on the entire wireless network is cut in half for each "remote" added to the network. So, with one "remote" in a WDS, you have a "g" wireless network running at 1/2 speed. If you have two "remotes" in a WDS, you have a "g" wireless network running at 1/4 speed.
Bob — thank you so much for the help.
Years ago in the days when Airport Extreme base stations supported 802.11b/g only, I remember setting up a WDS network between three Airport Extreme base stations. I seem to remember that the one in the middle was set up in a “relay” mode to bridge between the two remote base stations. In theory, using multiple relays, you could extend a network arbitrarily far as long as you could get power to all the devices and didn’t care about all sorts of bandwidth, latency, and signal strength hits.
Is it the case that with the 802.11n in current Airport Extreme stations you can't set up relays in a similar fashion using the "Extend a Network" wireless mode? I was looking at Apple’s “Designing Airport Networks Using Airport Utility” document, which doesn’t explicitly say, but seems to suggest that the central base station (operating in “Create a Wireless Network” mode) can be extended if the “allow this network to be extended” button is set, and then on a second base station you can use the “Extend a Wireless Network” mode to extend it. However, there’s nothing to suggest that you could extend off the second base station. Does anyone know if that’s possible?
I was looking at Netgear-brand wireless extenders this morning (http://www.netgear.com/home/products/wireless-range-extenders/wireless-range-ext enders/default.aspx) which sell for around $75 to $80 each online. They can extend any 802.11b/g/n network if the remote device supports the WPS (Wireless Protected System) standard, as most Netgear products appear to do (I believe Airport Extreme base stations don’t support WPS). They make it quite easy to connect Netgear wireless devices using “Push ’N’ Connect” buttons on the devices.
However, Netgear pre-sales specialist pointed out that the Netgear wireless extenders (the WN2000RPT is the current model) can similarly only extend out by one hop from the “center” and cannot operate as relay to get out further, as would be the case for WDS-based relays.
Is it the case that you need to find devices that support WDS (Wireless Distributed System) to allow for multiple relays to cover longer distances? I know that Airport Extreme base stations, both current models and the older b/g models, support WDS. Can anyone recommend third-party WDS-capable wireless modems or access points?
Any help would be appreciated.

Self made trigger for third party device?

Hi, everyone! I am new to labview programming.
Recently I have been trying to realize a function to trigger(or start) the third party device to do acquisition. I want to use the DAQmx to acquire one channel signal(which is continous pulse signal). And use this DAQmx acquired signal to trigger the third party device. I want each pulse signal to start the third party device to do acquisition.
Could someone give me some advice or suggestions? I would be grateful for any of your help. Thanks in advance.

Hi, Lynn
Thank you very much. I am glad to get your reply. First I am sorry for my lack of knowledge of Labview. I will learn and be more careful of using the terminology.
I have "NI PCI-6052E" as the hardware device. And I use "BNC-2120" connector block to connect the trigger source. I useonly one channel of 6052E to acquire the signal. This trigger signal actually is periodic pulse signal of voltage ranging from 0 to 5V. The pulse voltage is 0V, all other are 5V.
I give my answers to your questions as followings.
What kind of signal does the third party device require for triggering?Is it a physical signal like a voltage or current?
The third party device actually doesn't have to use this pulse trigger to start, I just want to make a customized trigger to sync the third party device with the pulse signal. And each pulse make the device start working. This pulse trigger is a voltage signal that can be linked to 6052E by BNC connectors.
Is it a message transmitted via USB, Ethernet, or tin cans and a string?
I am sorry, I don't get this. I guess it transmitted by BNC.
What is the timing of the signal you are acquiring?
I used the sample clock in DAQmx timing function.
How much latency can you tolerate between the acquired signal and the trigger to the third party device?
I actually can control the interval time between each pulse. I require this interval time to be more than 1s and during this time the third party device can do acquisition itself. So the latency I think should be in the range of ms.
Do you need to do any signal processing or analysis on the acquired signal to generate the trigger?
The trigger signal is pulse signal. Actually I don't know much about signal processing, I don't know what kind signal is better for my application. If you have any better idea, please let me know.
Thanks a lot.
Yu

IC WebClient Connectivity with ICI and Third Party Solution (Genesys)

<b>Hi Techies,
Can any body give the information about the IC WebClient Connectivity with ICI and Third Party Solution (Especially Chat and Mail Configuration with Web Client in CRM). We are using CRM 5.0 server with Java+Abap Engine. I need configuration for Web Client Genesys(Third Party) with ICI configuration. I dont have idea regarding this. I 've little idea on Business Communication Broker. Can any help me out in this regard. Thanks in an advance. If u have any document it can be acceptable.
Regds,</b>
Govinda
[email protected]

We are looking for a site to site model. I want all the devices on the remote network to be on their own subnet. We need to be able to hit individual remote devices from the head end. The devices at the remote site in turn also need to be able to communicate with each other without having to use the VPN.

Cisco Prime Infrastructure 2.0 -- Third Party Devices

Hello,
we are using cisco prime infrastructure 2.0. Is it possible to manage third party devices? (We have a lot of Enterasys Switches)
When i want to Archive the config of the device there is an error --> No Device Package found for the specific device.
It is necessary to install device packages for third party devices? Where can i find and install these packages?
Thx in advance

it seems not to be on the road-map according to the functional /feature comparison between LMS and PI 2.0:
http://www.cisco.com/en/US/partner/prod/collateral/netmgtsw/ps6504/ps6528/ps12239/guide_c07-729089.html
...and I doubt it will come (quickly) because config management has a lot of pitfalls and Cisco has a lot to do to get around all of them with their own devices..
However, Inventory Management for third party devices is on the road-map
older version of the document (feature comparison PI 1.2 - LMS 4.2) can be found here:
http://www.cisco.com/en/US/partner/prod/collateral/netmgtsw/ps6504/ps6528/ps12239/app_note_c27-716230.html

Integration between SAP and third party tax software

can some body explain me or provide me docs regarding integration between sap and third party tax software like vertex.
Thanks

Hi
First configure the same via the following menu path:
1.) IMG>Financial accounting>Financial accounting global settings>Taxes on sales/purchases>Basic settings>External tax calculation>Define physical destination
2.) Then test connection (option is available there).
3.) If the connection is successful, also verify that the external tax package installed supports the R/3 4.6 version of the API. You do that by going to:
System Information>Function List
Check if the following functions are listed:
RFC_CALCULATE_TAXES_DOC
RFC_UPDATE_TAXES_DOC
RFC_FORCE_TAXES_DOC
RFC_DETERMINE_JURISDICTION
4.) Then test the tax data retrieval:
From SE37, select the relevant function modules like RFC_DETERMINE_JURISDICTION.
The above 4 steps are necessary to satisfy that the RFC connection is established
Hope useful
S Jayaram

Connect report output to third party systen

Dear Techis
Can we connect Report output to third party system and hw?
Pls advice............

Hi Yong,
Yes that's possible. You can use the web interface to configure logging category messages so that they are sent to remote syslog server targets
http://www.cisco.com/en/US/docs/net_mgmt/cisco_secure_access_control_system/5.3/user/guide/logging.html#wp1052741
ACS provides these preconfigured global ACS logging categories, to which you can assign log targets.
http://www.cisco.com/en/US/docs/net_mgmt/cisco_secure_access_control_system/5.3/user/guide/logging.html#wp1052549
Configuring Per-Instance Remote Syslog Targets
http://www.cisco.com/en/US/docs/net_mgmt/cisco_secure_access_control_system/5.3/user/guide/admin_config.html#wp1063768
Jatin Katyal
- Do rate helpful posts -

Alarms for Third party devices on Cisco PI v 2.1

Is it possible to receive alarms for third party devices in Cisco Prime Infrastructure 2.1? If so how do i configure PI to show the alarms?

Hi,
AFAIk, It is not possible to receive alarms for third party devices in Cisco Prime Infrastructure 2.1.
we have very limited support of 3rd party devices in PI. third party devices only snmp polling, snmp traps and syslog will work
Third-party support
● Ability to discover and monitor third-party (non-Cisco) switches that support RFC 1213 and wireless controllers/access points from Aruba Networks
Thanks-
Afroz
****Ratings Encourages Contributors ****

PI 2.1, exclude third party device from config archive

Hi,
Customer runs PI 2.1. He has also third party devices in the PI inventory.
Now, every time the configuration archive job is running, this third party devices are failing. Which is the normal behavior. Is it possible to set,for example a filter, to exclude this devices from the configuration archive job?
thank you very much for your help
Hansruedi

Hi Hansruedi,
we have to manually exclude them from Config collection::
Operate >Device Work Center > Configuration Archives ,
Check the check box for "Name" , this will select all the devices then unselect the one you DON't want to get archived .
click on " scheduled Archive" and scheduled it as per your need (hourly , weekly ...etc..)
Thanks-
Afroz
**Ratings Encourages Contributors ****

How to enable the "SNMP TRAP" Funcation in Prime Infrasructure 2.0 for receiveing the Third Party Device's SNMP TRAP

I already uploaded the third party device's MIB to PI2.0, but could not recive the third party device's SNMP TRAP properly .
what do I need check for the PI ? or what do I need to setup for the PI?
Thanks

Duplicate post of :
https://supportforums.cisco.com/discussion/12148626/how-enable-snmp-trap-funcation-prime-infrasructure-20-receiveing-third-party
-Thanks
Vinod

Connect Report output to third party system

Dear Techis
Can we connect Report output to third party system and hw?
Pls advice............

Hi Yong,
Yes that's possible. You can use the web interface to configure logging category messages so that they are sent to remote syslog server targets
http://www.cisco.com/en/US/docs/net_mgmt/cisco_secure_access_control_system/5.3/user/guide/logging.html#wp1052741
ACS provides these preconfigured global ACS logging categories, to which you can assign log targets.
http://www.cisco.com/en/US/docs/net_mgmt/cisco_secure_access_control_system/5.3/user/guide/logging.html#wp1052549
Configuring Per-Instance Remote Syslog Targets
http://www.cisco.com/en/US/docs/net_mgmt/cisco_secure_access_control_system/5.3/user/guide/admin_config.html#wp1063768
Jatin Katyal
- Do rate helpful posts -

How to connect Developer 6i with third party Databases

How to connect Developer 6i with third party Databases

Hi,
Oracle Forms 6i comes with a Oracle Client Adaptor, OCA, that allows you to connect to 3rd party databases. Starting Forms 9i you use gateways.
Frank

Is LMS3.2 support third party devices??

Hi,
Running LMS 3.2.
Can it possible to monitor or add the third party devices like Juniper and Checkpoint ???
Thanks & Regards,
Krishna

Hi Krishna,
No it's not Possible , Below is the list of Devices supported in LMS 3.2 :
http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/3.2/device_support/table/lms32sdt.html
Thanks--
Afroj

Operate a third party device

HI
I try to operate a third party Camera (C CAM) by LabVIEW. I try by call library function node. But I fail to get data by call library function node.
Is there have any other way to operate third party device except call library function / CIN?
Thanks
Kamal

Kamal;
Other ways to access a third party device is via ActiveX, sending commands via the system exec VI, etc. However, my guess is that you need to try harder with the .dll
Make sure you check the following articles: An Overview of Accessing DLLs or Shared Libraries from LabVIEW and External Code for LabVIEW - CIN / DLL - Starting Point
The article "Can LabVIEW C? - Example 3: Using the Right Tools with LabVIEW" is an excellent starting point.
I don't know about that camera, but if it is a webcam, you can do a search on toolkits to access a webcam from LabVIEW.
Regards;
Enrique
www.vartortech.com

Integration between SAP and Third Party without PI in between

Hi All,
We have a requirement where in we need to integrate SAP and a Third Party Product without PI in between.The third party product is exposing their Web services as API.
So, we have an idea of exposing our RFC/BAPI as web service ,so that it can call/consume the third party web services.On these lines I have a couple of doubts,
1.How will the monitoring of message be done?Is there any Tcode to monitor the RFC exposed Web services?
2.What would be the advantages and disadvatages of this approach?
Thanks.
Venu

Well taking out PI will 'exclude' advantages like able to monitor the messages, resending messages, error handling etc.

Ethercat connection between windowsPC an third party device.

Similar Messages

Maybe you are looking for