Etherchannel between stack switches[3750] and standalone switch[3560]

Hi,
I have 2*3750 switches in stack as core and 1*3560 switch in access layer. I want to enable ether channel between stack switch[3750A & 3750B] and 3560 switches.
Have connected  2 links from 3560 switch to stack switch, one link to 3750A and other link to 3750B. Will it work in this way as per my requirement? 
or i should enabled stacking on 3560 switch too and configure cross-stack ether channel between 3750 stack and 3560 stack. i refered few cisco documents, but the cross stack etherchannel configuration example has 3750 at both end stacks.
Rgds...
VikramS

Hi,
 This should work fine as per you set up, the 3750 stack will be acting as one switch, which means that the ether-channel configuration should be straight forward. There is no need to stack the 3560 for this to work, also the 3560 are not stackable.
Hope this helps.

Similar Messages

  • 802.1x between Switch 3750 and ACS 4.2 Authentication faild --need help

    I configured the Switch 3750 and ACS for 802.1x authentication.
    when I used the windows as the 802.1x client, it prompted "click here to enter user name and pasword for the network " as normal.
    The problem is that after I entered username and password (i am sure i enter the identical username and password as in ACS) the authentication failed,
    What is the most possibly problem?
    Thx in advance!!!
    The configuration is Sw3750 is:
    aaa new-model
    aaa authentication login default local
    aaa authentication enable default line
    aaa authentication dot1x default group radius
    aaa authorization network default group radius
    dot1x system-auth-control
    interface GigabitEthernet1/0/18
    description Link to test 802.1x
    switchport access vlan 119
    switchport mode access
    dot1x pae authenticator
    dot1x port-control auto
    spanning-tree portfast
    radius-server host 10.1.1.333 auth-port 1645 acct-port 1646
    radius-server source-ports 1645-1646
    radius-server key keepopen0
    In the ACS:
    Network Configuration -->aaa client ip address: 10.1.119.1(the vlan 119's ip address), shared secret: keepopen0
    user setup -->real name:test1, password: test1.
    Attached is the debug information

    What do you see in acs failed attempts?

  • 375o switch in stack, only 2nd and 3rd switch reboots

    Hi,
    In customer place we are having three 3750 switch and it was stacked and working fine. Few days back the in stacked switches 2nd and 3rd switches are rebooted continuously and found in the show version command as: Data TLB Miss Exception (0x1100)!.
    From last 4 days we are not found any reboot. Please let us know any software bug is triggered to cause this problem, if upgraded please let us know the image to be put in all the three switches. I am sending the show tech output of all the 3 switches and show stack output.
    Thanks in advance.
    Regards,
    Ram

    This URL should help you:
    http://www.cisco.com/en/US/products/hw/switches/ps5023/prod_release_note09186a00801b476a.html

  • Switches of and wont switch on

    Switches off and wont switch on

    Restore iPhone with iTunes on computer. If still problem after the Restore, the iPhone 5S has full Warranty, make Genius reservation or set up service and take or send to Apple for resolution.

  • HT4623 atleast once in a week the slide to unlock will not work in my iphone 4 and this is happening from the day i have upgraded to ios7. to access my iphone i have to a switch off and then switch on. really frustrating never

    atleast once in a week the slide to unlock will not work in my iphone 4 and this is happening from the day i have upgraded to ios7. to access my iphone i have to a switch off and then switch on. really frustrating never expected this from Apple.

    Hello sivas_live
    Try out the troubleshooting steps in the article to resolve issues with your touchscreen intermittent response.
    iPhone, iPad, iPod touch: Troubleshooting touchscreen response
    http://support.apple.com/kb/ts1827
    Regards,
    -Norm G

  • HT1386 My iPhone switched off and cannot switch it on

    I just update the OS and my iPhone switched off and cannot switch it on

    Hold the sleep/wake and home button together until you see the Apple logo and then release. The phone should reboot. This can take up to 30 seconds worth of holding.

  • Problems between a Wireless Controller and a Switch.

    I have a Wireless Controller 4402 connected to one sw2960G.
    I configured the controller with LAG and the switch (sw2960G) with etherchanel.
    I connected the controller 2 distribution ports to the 2 ports of the switch (configured with etherchanel).
    It worked like it should work.
    But the problem is like this: if I take one cable that is connected to the switch and unplugged that cable from the switch (if that cable is the one connected to controllers port one) I have connectivity between both machines.
    If I plug in the switch the cable connected to controller port one and take the other cable and unplugged that cable from the switch I stop the connectivity between the two machines.
    I think that was not supposed to happen… because the LAG in the controller should put every AP in the second controller's port, and the connectivity between the machines should not end.
    Can any one help me?
    Can any one tell me what I am doing wrong?
    Thanks in advance,
    Rui

    With LAG enabled in the controller I think I can have only one ap-manager interface.
    The LAG will (it is supposed to) do the load balance automatically.
    I mean, if one of the interfaces is “down” the other will have to coupe with all the AP's.
    I should have always connection between the controller and the switch.
    The STP of the controller is configured by default (STP Mode = OFF).
    In the case of etherchannel load balance… I saw the Cisco documentation and I did not saw any thing about that. I think that The LAG as to do that for the controller… I'm right about that?
    I will see the link that you advised…
    Can you help me?
    Thanks,
    Rui

  • Etherchannel between WS-C4506-E and stacked WS-C2960S-48LPS-L

    Hello,
    we are having a "suspend" issue to portchannels with 2960S switches only.
    On our core switch we have the following setup:
    interface Port-channel68
     description EC DELEJ02SAC88
     switchport
     switchport trunk allowed vlan 6,7,10-12,19-21,30,63
     switchport mode trunk
    and the two ports are:
    interface GigabitEthernet1/3/10
     description SAC88
     switchport trunk allowed vlan 6,7,10-12,19-21,30,63
     switchport mode trunk
     logging event link-status
     udld port aggressive
     channel-group 68 mode active
    interface GigabitEthernet2/3/10
     description ECM DELEJ02SAC88-D20
     switchport trunk allowed vlan 6,7,10-12,19-21,30,63
     switchport mode trunk
     logging event link-status
     udld port aggressive
     channel-group 68 mode active
    On the other end we have a stacked 2960s with two switches.
    Ports are configured as this:
    interface Port-channel1
     description Uplink Core
     switchport trunk allowed vlan 6,7,19,21
     switchport mode trunk
    and the two stack ports (one of each switch):
    interface GigabitEthernet1/0/49
     description Uplink Core/Chassis1
     switchport trunk allowed vlan 6,7,19,21
     switchport mode trunk
     udld port aggressive
     mls qos trust dscp
     channel-group 1 mode active
    and
    interface GigabitEthernet2/0/49
     description Uplink Core/Chassis2
     switchport trunk allowed vlan 6,7,19,21
     switchport mode trunk
     udld port aggressive
     mls qos trust dscp
     channel-group 1 mode active
    Same configuration we do have on our not stacked 2960 and is working fine. But here we have one port in supended state:
    Group  Port-channel  Protocol    Ports
    ------+-------------+-----------+-----------------------------------------------
    1      Po1(SU)         LACP      Gi1/0/49(P) Gi2/0/49(s)
    We don't have anything in the logs.
    Do anybody came across with this issue or having nay idea how to fix it?
    Many thanks in advance
    @lex

    I met similiar problem on C4500.
    Try to remove etherchannel configuration by taking ports to it's defaults and also interface Port-channel68.
    Then create port channel interface by first issuing :
    interface GigabitEthernet1/3/10
     description SAC88
     channel-group 68 mode active
    interface GigabitEthernet2/3/10
      description ECM DELEJ02SAC88-D20
      channel-group 68 mode active
    Then configure all stuff around switchport under interface Port-channel68.

  • Uplink between Stacked Dell 8132 and Cisco 1921 HSRP pair.

    Hello,
    I have three Dell 8132 switches stacked and we plan on connecting them to an HSRP pair of Cisco 1921 routers. What would be the best way to uplink these stacked switches to the 1921 pair? 
    I was thinking of creating vlan trunk from 2 of the 3 Dell switches, one trunk going to each router and enable HSRP on these trunks for the vlans I need to route. Would that be a good approach?
    Attached is a basic network of what it would look like. Please suggest if this is a good way to accomplish this or if there is a more better and efficient way to do it?
    Thanks

    Just to clarify I wasn't suggesting that you move all the routing to the Dell switches. If the routers are already doing some routing for you then you could simply connect the Dell switches with L3 uplinks.
    But yes if you feel more comfortable using Cisco then use the routers.
    I have never used an integrated switch module to be honest, I just used L3 switches and routers separately.
    I suspect it would work as long as there was a backplane connection between the switch module and the router itself so you could route directly from the switch module to the router.
    Can't say for sure whether there is or not as like I say I have never used them.
    Which to use really comes down to how much bandwidth you need between vlans which only you know really. If you think using one interface and splitting it up may cause problems then you could look at a switch module.
    Although it does seem a bit redundant purchasing a switch module when you have L3 switches already :-)
    But I do understand what you mean about being a Cisco shop.
    Jon

  • Conecting etherchannel between cisco catalyst 6509 and hp procourve 9308

    Impossible to connet 2 ports 1000base sx agrouped via etherchannel / lacp or pagp between a catalyst 6509 and a hp procourve 9308. Please do you know he best configuration? thanks in advance

    Hola Luis,
    the link would have to be LACP (since PAgP is Cisco proprietary). So, on the Cisco side, the config should look like this:
    interface GigabitEthernet0/1
    switchport trunk encapsulation dot1q
    switchport mode trunk
    channel-group 1 mode on
    interface GigabitEthernet0/2
    switchport trunk encapsulation dot1q
    switchport mode trunk
    channel-group 1 mode on
    interface Port-channel1
    switchport trunk encapsulation dot1q
    switchport mode trunk
    On the HP side, check how the trunk group is configured there. I assume you have used the ´trunk deploy´ command after configuring the HP trunk group ? Also, which spanning-tree mode do you have running on the Cisco and the HP ?
    Saludos,
    GP

  • Comparing switch control and switch output and setting switch control accordingly

    Hello,
            i am developing a GUI for a system which contains relays to control the motors. For the same purpose i am using switch control on my GUI to control these relays.when these relay  are turned ON by the switch control on my GUI, they give back status to the GUI, which i am displaying as a switch status .
    Now the switch control and switch status on GUI must be same every time so that user can know the actual state of relay and control it.
    Now i have a condition when i have already turned ON switch from my GUI but due to some reason (may be communication fault or anything else) rellay is not turned ON and i get status of relay as OFF on my switch indicator. So the situation is" the switch control is in ON state and switch indicator displays OFF state".  which is practically wrong.
    I want that in this case the GUI should detect the status of the switch indicator and if the switch control is not the same , the switch control should be set as per the switch indicator so that user can use the switch again to turn the switch ON

    Hello Mike,
                        Thanks for the response!!
    As i have described the situation above, in any case if switch control fails to send message to relay due to some hardware fault , in that case relays will be off and the switch on GUI will be ON , and user will think that the relay is ON.Which is false condition.
    i tried to use property value(signl)   to give back the status of switch indicator to the switch control.
    You can have a look at attached files which i have made as demo.
    Now the problem is when i run my GUI for the first time all the switch on the front panel are off by default which creates a conflict to control the switches.
    Besides i am unaware of the timing events and how to implement it in my application . It would be great if you could provide some more details about it.
    Thanks & Regards,
    Shivkant Paswan
    Attachments:
    switch control trial.zip ‏16 KB

  • EtherChannel between stacked VSS Catalyst 4500X and Stacked 2960X.

    I can have only one link in the EhterChannel up but the 2nd one goes in to suspended mode. 
    I've tried recreating channel group on different ports but with the same results. Am I doing something wrong or pagp cannot be transmitted over stacks on both ends (I have quite a few EtherChannels but all to single/non-stacked switches)?
    2960X stack config
    Version: 15.0 (2r)EX
    interface TenGigabitEthernet2/0/2
     description HR-Link1
     switchport mode trunk
     switchport nonegotiate
     channel-group 2 mode on
    interface TenGigabitEthernet1/0/2
     description HR-Link2
     switchport mode trunk
     switchport nonegotiate
     channel-group 2 mode on
    4500X Stack (VSS) config
    Version: 03.04.00.SG (fc3)
    interface TenGigabitEthernet1/1/12
     description MO-Link1
     switchport mode trunk
     switchport nonegotiate
     shutdown
     channel-group 12 mode on
    interface TenGigabitEthernet2/1/12
     description MO-Link2
     switchport mode trunk
     switchport nonegotiate
     shutdown
     channel-group 12 mode on
    Thank you,
    T

    Thanks for reply!
    I have tried desirable mode as well but no luck. I can work on this only during the weekend as downtime is not an option.
    These two 10G links were just installed last weekend and one patch cable I had to replace due to complete lack of connectivity (small shop so we no fiber testing equipment).
    I did not do a lot of troubleshooting last weekend but I will dig in to that this weekend. I was hoping to get some insight from people who work with this on daily basis.
    Post from about a year ago got me worried:  https://supportforums.cisco.com/discussion/12072281/4500-x-vss-mec-2960-x-stack
    Thanks again.
    T

  • How to stack a SG500 and SG500X switch?

    Hi, I've been trying to stack three switches a SG500-28P a SG500-52P and a SG500X-28P - the SG500s stack fine, however when I added the 500x to the stack, the unit deactivated itself and took itself off the network - not good as it was the core switch! 
    Any ideas what's going on, are they using a different stack protocol to the others - I was just going for native and 5G ? 
    Firmware was 1.3
    Many thanks,
    Chris 

    Hi,
    SG500 and SG500x only supports native stacking.
    Native Stacking—A device is capable of joining other devices in native 
    mode with its stack ports to form a stack. All units in a native stack must be 
    of the same type (all Sx500 or all SG500X).
    See the attachment
    Regards
    Moorthy

  • Permanent up/down link between host fiber card and fiber switch

    During connecting emc symterix to ORACLE VM machine with ECC there is instability of connection as described here:
    Description: Switch switch31 Slot 3, Port 4 Linkdown. Reason: None
    Severity: CRITICAL
    Server Timestamp: Mon Jul 26 17:39:26 IDT 2010 Agent Name: Fibre Channel Connectivity Agent Agent Timestamp: 2010/07/26 17:39:08 Alert Name: Port Link Status Changed Alert ID: 534 Host Name: zil01app15.ds.mot.com Canonical Managed Object Name: Connectivity Device=2000000dec6d6280>Connectivity Port=2084000dec6d6280 Managed Object Persistent Id: [com.emc.ecc.dl.persistent.topology.ConnectivityDevFibrePort,3369032]
    Description: Switch switch31 Slot 3, Port 4 Linkup
    Severity: NORMAL
    Server Timestamp: Mon Jul 26 17:39:28 IDT 2010 Agent Name: Fibre Channel Connectivity Agent Agent Timestamp: 2010/07/26 17:39:08 Alert Name: Port Link Status Changed Alert ID: 534 Host Name: zil01app15.ds.mot.com Canonical Managed Object Name: Connectivity Device=2000000dec6d6280>Connectivity Port=2084000dec6d6280 Managed Object Persistent Id: [com.emc.ecc.dl.persistent.topology.ConnectivityDevFibrePort,3369032]
    link is going up and down
    any idead what can it be ?
    Regards
    Victor

    we also tried the following:
    2.     We compared OS/driver versions on both ( Oracle VM and Oracle Linux ) machines.
    Here is the table:
    Hostname OS HBA version
    zil01gscapp01 Oracle VM server release 2.21 8.03.00.10.02.02_k
    zil01gscmgt01 Oracle Enterprise Linux release 5.5 ( Carthage ) 8.03.01.04.05.05_k
    From this comparison we concluded that VM server HBA driver should be upgraded.
    We have downloaded from the QLOGIC site driver version 8.03.01.06 ( see the link )
    http://driverdownloads.qlogic.com/QLogicDriverDownloads_UI/SearchByProduct.aspx?ProductCategory=39&Product=937&Os=65
    By installing driver we got following error:
    [root@zil01gscapp01 qla2xxx-src-8.03.01.06.05.06-k]# ./extras/build.sh install
    case=install here2 main
    QLA2XXX -- Building the qla2xxx driver...
    drv_build modules
    RedHat 1 make -j5 -C /lib/modules/2.6.18-128.2.1.4.25.el5xen/build M=/tmp/qla2xxx-src-8.03.01.06.05.06-k modules
    make: Entering directory `/usr/src/kernels/2.6.18-128.2.1.4.25.el5-xen-i686'
    make: *** No rule to make target `modules'. Stop.
    make: Leaving directory `/usr/src/kernels/2.6.18-128.2.1.4.25.el5-xen-i686'
    /lib/modules/2.6.18-128.2.1.4.25.el5xen/kernel/drivers/scsi/qla2xxx/qla2xxx.ko
    QLA2XXX -- Installing the qla2xxx modules to /lib/modules/2.6.18-128.2.1.4.25.el5xen/extra/qlgc-qla2xxx/...
    install: cannot stat `*.ko': No such file or directory
    It looks like there is no kernel source in order to compile with the new driver, in other words Oracle VM comes wihout kernel source.
    Please, your advise/opinion about all above activities and further work.

  • Etherchannel between 2960 switches

    Hello All,
    I configured etherchannel between two 2960 switches.
    Both the switches have SVI with subnet 192.168.2.3 and 192.168.2.4
    I have another vlan3 on one of the switch.
    so when i created etherchannel between two Gig ports and allowed both the vlans,it gave me an error messg,
    Nov  3 12:41:07.332 KSA: %EC-5-CANNOT_BUNDLE2: Gi1/0/19 is not compatible with Gi1/0/20 and will be suspended (vlan mask is different)
    Nov  3 12:41:07.339 KSA: %EC-5-CANNOT_BUNDLE2: Gi1/0/19 is not compatible with Po1 and will be suspended (vlan mask is different)
    Nov  3 12:41:07.339 KSA: %EC-5-CANNOT_BUNDLE2: Gi1/0/19 is not compatible with Po1 and will be suspended (vlan mask is different)
    Nov  3 12:41:07.339 KSA: %EC-5-CANNOT_BUNDLE2: Gi1/0/20 is not compatible with Po1 and will be suspended (vlan m
    May i know why....
    Thanks

    Hello Mudasir
    This will be a problem of allowed vlan mismatch. All the interfaces which are going to add in the etherchannel must have same allowed vlan on both sides.
    You can check for the allowed vlan on all the interfaces as well as on Port-channel.
    You can see the below forum having the same problem:
    https://supportforums.cisco.com/discussion/9757346/etherchannel-prob
    Regards,
    Mukesh Kumar
    Network Engineer
    Spooster IT Services

Maybe you are looking for

  • Time Capsule Problems - No DNS Servers Where did they go?

    I have an iMac and macbookpro using a TC connected to high speed cable modem. Everything has worked fine for a year+. All of the sudden I can't connect to Internet. Under airport utility it says I have no dns servers and has two empty boxes. Then it

  • IOS 8.3 and the auto rotation of the screen problem?

    I upgraded to IOS 8.3 and the auto rotation of the screen has stopped working on my iPad Air 2, has anyone else got this problem?

  • Automatic SOS in shopping cart for reservation items

    Dear all, I am creating a shopping cart using a catalog item that creates a reservation in the backend (classic). However, when i change sthing, the system reads an info record that exist in the back-end and assigns the vendor as the source of supply

  • The navigation form in access 2010

    I have several calculated fields in a sub form and when I try to add the form and its sub form to a navigation form the calculated fields in the sub form stop working.

  • Not receiving message on iphone, but yes on ipad

    Having weird problem with iMessage. First, I have a iMac osx 10.8.3, iphone5 ios 6.1.3, and new ipad (3) ios 6.1.3 All our configured to receive imessages using my email and telephone number. Sending doesn't seem to be a problem, but when I receive a