Ethernet configuration Airport Express won't work - please help!

I'm trying to add an Airport Express to my network but having lots of trouble. I'd like to duplicate the settings of the existing one in the new one and simply change the IP address of the new one. (The existing unit has a static IP and works fine.) The network seems to be interfering with the setup process, so I connected my iBook directly to the new AP Express via ethernet. In Airport Admin, when I click other I get a dialog with the IP address 10.0.1.1 (which I assume is the default IP of a new AP Express) and a password field. The dialog is inactive until a password is entered, but I don't know what the default password, if any, is.
Will entering a default password allow me to do the configuration? What is it? If not, how do I configure the unit?

Thanks Duane. Couldn't find it anywhere. I'm still unable to connect to my new AP Express.
I created a new location called "AP config" and set ethernet TCP/IP to DHCP. After connecting computer to AP Express w/cable, clicking "Other" in AP Admin, and entering "public" into password field, I got a dialog telling me "unasble to read configuration."
Any suggestions?

Similar Messages

Airport express setup, not working, please help me out

i recently purchased a airport express so that i can extend the range of my current network, use airtunes, and have wireless printer sharing. My base station is a d-link router, and from there i have been having a lot of problems. I have been able to set up the airport express part of the way, but not with complete functionality. I have been able to use it for music and i havent tried printing, but i cannott connect through the internet with it, i have to revert back to my base station router for that.I have tried the entire manual, scoured the mac support website and googles this problem for hours with no end. please help me out here, this is getting pretty frustrating
thanks for all the help in advance

Hello CAUTION5697. Welcome to the Apple Discussions!
Unfortunately, most non-AirPort routers are not compatible with Apple's implementation of Wireless Distribution System (WDS)...so it very unlikely that your D-Link router can be extended wirelessly with the AirPort Express Base Station (AX).
The few that are known to work are:
o another Airport Express Base Station
o 802.11g Airport Extreme Base Station (AEBS)
o 802.11n AirPort Extreme Base Station (AEBSn)
o Linksys WRT54G or WRT54GS (not v5)
o Belkin F5D7230-4 and F5D7231
o BT Voyager 2091
o Netgear WGR614 v6
o Buffalo WGR-G54
Instead, you can configure the AX to "Join an existing wireless network" for both streaming iTunes and for sharing a USB printer. Check out the following Apple article on how: AirPort Express: How to join an existing wireless network in client mode

AirPort Express won't work with 7.0.2

Everything was fine til I bought a new Shuffle. It made me upgrade to 7.0.2, now my Airport Express won't work. I have firmware 6.2 and just uploaded all of the newest updates from apple.com for it (AX). The security is off on my network and the AX is connected with a green light. Still no option to choose my home stereo which is hooked up to the AX. HELP! I have spent all day trying to get this to work!!!!

My Airport Express when it is setup to extend my network while plugged into Ethernet will Create a network under settings
This is the correct setting to "extend" the network using an Ethernet connection. Technically, this is called a "roaming" network.
If I change this to Extend A Network it doesn't work properly.
This is because "Extend a wireless network" is used only when AirPort devices communicate with each other using wireless only......not Ethernet.
It would help if Apple used settings like "Extend a network using Ethernet" and "Extend a network using wireless only".....but they don't.
The AirPort Extreme will need to be configured as the main router if you want it to provide a Guest Network. It cannot do this if it is configured in Bridge Mode.

HT4437 i want to play contents from macbook pro to B&W zeppelin air wirelessly,set up is done but can't see airplay button in iTunes,do i need airport express?why?please help.

i want to play contents from macbook pro to B&W zeppelin air wirelessly,set up is done but can't see airplay button in iTunes,do i need airport express?why?please help.

There are at least 3 versions:
http://www.bowers-wilkins.co.uk/Support/Support/iPod_and_Computer_Speakers/Overv iew.html
Original Zeppelin - I've had this for several years.
http://bowersandwilkins.custhelp.com/app/home/p/6,26
Zeppelin Mini.
http://www.bowers-wilkins.co.uk/iPod_and_Computer_Speakers/iPod_and_Computer_Spe akers/Zeppelin_Mini/Overview.html
Zeppelin with Airplay.
http://www.bowers-wilkins.co.uk/iPod_and_Computer_Speakers/iPod_and_Computer_Spe akers/Zeppelin_Air/
(I wouldn't regard the MM-1 as a Zeppelin but not sure if B&W call it that).
I can't do much more to convince you!
You could always update that wiki
AC

HT201406 i have been having trouble my iphone 3gs doesn't work the slide to unlock is broken i have tired everything to get it open but it won't work please help me!

i have been having trouble my iphone 3gs doesn't work the slide to unlock is broken i have tired everything to get it open but it won't work please help me!

Basic troubleshooting steps are: Restart, Reset, Restore,

Airport Express Won't work on Computers but works on other devices

I switched from att dsl to comcast internet. I set up my modem and then purchased an airport express to use as my wireless router. When I set up my airport express, I installed the airport utility on my windows vista laptop, was able to create a network, password, etc.. However, once set up, I could no longer find my airport express in my airport utility. My windows vista laptop, and windows 7 laptop can not connect to the internet. I also installed airport utility on the windows 7 laptop and that laptop cannot locate the airport express. However, my PS3, Wii, iPhones, and old XP desktop can all locate the network, connect and work very well.
Also, if I directly connect the ethernet cable into either laptop, they will connect to the internet fine. I have tried downloading drivers, changing security on both, resetting the airport, power cycling, and have not succeeded. I have no idea what to do next. I can not understand why most of my devices can detect the router and others can not. I know that the laptops can connect wirelessly because I brought them to my parents house to test them out and they both worked fine.

Hello akommatas. Welcome to the Apple Discussions!
Please try temporarily disabling the Windows or third-party software firewall on any PC that is having difficulties accessing the AirPort Express Base Station (AX) with the AirPort Utility. Can the utility find and access the AX now?
If not, instead of waiting for the AirPort Utility to scan, go to the utility's menu bar, and then, choose File > Configure Other ... > Enter 10.0.1.1 in the IP Address field, and then, enter public for the password.

Older model Airport Express won't work with Mountain Lion Airport Utility

just upgraded to Mountain Lion and noticed that of my network of three airport expresses connected to various stereo speaker systems throughout the house, one of the older models won't work with the supplied version of Airport Utility (v 6.1). Here is the message it gives in the utility when I attempt to select this particular Airport Express:
"This version of AirPort Utility doesn't support this base station. Use AirPort Utility 5.6 to configure or manage this base station. AirPort Utility 5.6 is available at AirPort Service and Support."
Well, I go to download v 5.6 and none of the versions available will install on Mountain Lion! (even the version for Lion) Catch 22.
Any resolution to this (other than having to go out and buy a newer version Airport Express)?
Michael

Learn how to install AirPort Utility 5.6 on Mountain Lion here:
http://www.macworld.com/article/1167965/mountain_lion_and_the_ancient_airport_ba se_station.html

Second Airport Express won't work

I'll explain my current set up first, then explain my problem. I have an iBook G4 running 10.4 with the latest version of Airport Utility. I have a BT Home Hub as my main wireless router, to that I have an Airport Express connected via an ethernet cable. To the AE I have a stereo lead connected to my amplifier. I use airtunes from my iBook to play music via the AE. I also connect the iBook to the internet via the AE unit (rather than through my BT Home hub as it's faster that way!).
Ok my question/problem:
I have a amp/speakers in my kitchen. Also the wi-fi signal in the kitchen is poor. On mentioning this to my Dad he mentioned he has a spare AE unit, why not plug it in and extend the range of my original wi-fi signal and connect my second amp/speaker set up that sits in the kitchen. We are both working to the assumption that when a second AE is connected to the network, you can simply go to iTunes, select the drop down menu in the bottom right hand corner (the "select which speakers" and I choose "Kitchen" instead of my current "Living Room" AE.
Now I've spent so may hours trying to make this scenario work, checking the usual sites but it just doesn't seem to work. My wife may divorce me if I spend much more time on this! Save my marriage and help me listen to my beloved music in the kitchen.
Can this be done?! It's driving me crazy!!

Sorry guys I'm totally lost now.
The two units are clearly not at the same firmware level, one being older than the other.
I can't find a selection anywhere for "extend a wireless network" on AX2
I've also tried to configure the 1st AX to act as a WDS main base station. The 2nd AX should be configured to act as a WDS remote base station and I get the error message:
"AIRPORT UTILITY WAS UNABLE TO FIND YOUR APPLE WIRELESS DEVICE AFTER RESTARTING.
The settings for this apple device have been successfully updated, but there was a problem re-joining the wireless network or finding the Apple wireless device. You may need to select your network again from the Airport menu and try again"
Which I can't do as AX2 disappears and I can't see it in the toolbar, or see it when I scan for it in Airport Utility and I can't see it in iTunes it just sits there flashing orange in the Kitchen as an expensive, useless bit of plastic.
Help.

Airport Express won't work with VPN

Finally made it through the nightmare of setting up my Airport Express to act as a wireless print server on my existing network (Linksys WRT54G router). However once I log onto my corporate VPN, I cannot print or even see the Airport. I have checked the LAN access box on the Transport tab of my VPN software which is supposed to allow split tunneling, but no luck. Everything works fine once I log off the VPN. I bought the Airport Express specifically because an Apple rep told me it would work with my VPN. My previous wireless print server (Linksys) would not support VPN.
Appreciate any help!

My Airport Express when it is setup to extend my network while plugged into Ethernet will Create a network under settings
This is the correct setting to "extend" the network using an Ethernet connection. Technically, this is called a "roaming" network.
If I change this to Extend A Network it doesn't work properly.
This is because "Extend a wireless network" is used only when AirPort devices communicate with each other using wireless only......not Ethernet.
It would help if Apple used settings like "Extend a network using Ethernet" and "Extend a network using wireless only".....but they don't.
The AirPort Extreme will need to be configured as the main router if you want it to provide a Guest Network. It cannot do this if it is configured in Bridge Mode.

Airport Express won't work unless it's behind a router...

After experimenting with my airport express to try and get it to work with some game of mine, I discovered that my airport doesn't get an internet signal unless the connection from the modem to the base station goes through a router.
This is really strange... does anyone know anyway to fix this?
By the way, yes, all my cables work, I use SBC Yahoo DSL as my ISP, I have a speedstream modem, and my connection apparently has to go through an Asante router, although it may work through other ones.

OK,
Is the IP address of the form 192.168.x.x, or 10.x.x.x, or something else ? This will help us identify if the ISP is allocating you an IP address dynamically, or maybe you have to key it (just once) because they've allocated you a static IP address.
The DNS server addresses present but greyed out is what I hoped to see. I had hoped Router address would be set (and greyed out), this is where all your internet traffic gets sent to. I'm also a bit puzzled at the Subnet mask not being 255.255.255.255, which would be the normal value for ISPs to set on customers connections.
If you plug your mac (if possible) straight into the ethernet cable that comes out of the modem, put the Network system preference on Automatic, and then check the Built-in Ethernet in the same system preference, what does it show ? same values as appeared in the Airport config ? This is just to rule out any other factors.
I'm sure the answer we need is in the configuration of your (nearly redundant) router. It will have settings, either already set, or allocated by the ISP that we need to mirror in the Airport. If you're comfortable in the router configuration, print (or screen dump) all the details, then we know what works and can begin to configure the Airport in a similar fashion.

Airport express won't work with Extend Network, only Create Network

My Airport Express when it is setup to extend my network while plugged into Ethernet will Create a network under settings. If I change this to Extend A Network it doesn't work properly. It keeps kicking me on and off WiFi, but the former way works with no foreseen issues. What is going on? I can't extend my guest network with the first option, I don't believe.
I have a 5th Generation AirPort Extreme and a 1st Gen AirPort Express.

My Airport Express when it is setup to extend my network while plugged into Ethernet will Create a network under settings
This is the correct setting to "extend" the network using an Ethernet connection. Technically, this is called a "roaming" network.
If I change this to Extend A Network it doesn't work properly.
This is because "Extend a wireless network" is used only when AirPort devices communicate with each other using wireless only......not Ethernet.
It would help if Apple used settings like "Extend a network using Ethernet" and "Extend a network using wireless only".....but they don't.
The AirPort Extreme will need to be configured as the main router if you want it to provide a Guest Network. It cannot do this if it is configured in Bridge Mode.

2nd airport express won't work

I have an airport extreme base station and 2 airport expresses. The first express is necessary to extend the range for our wireless in the house. I can't get the second express to work with itunes since I started using the first express to extend range.
I have configured it and my computer sees it but it doesn't stop flashing amber and itunes tries to connect but is unable.
The guy at the apple store told me that it IS possible but I must be doing something wrong.
Thanks for any help.

Hard reset the second Airport Express and reconfigure it to join your existing network in client mode.
Resetting AirPort Express
http://docs.info.apple.com/article.html?artnum=108044
iFelix

AE(Airport Express Won't Work)`

i trying everything it says im connected though i cant get any internet access expect for Skype what do i do
Any ideas please
???????????????

Probably DNS is not working correctly. Try restarting the Airport Express base station.

My Airport Express Won't Work

I need help! I have airport express and it won't work. I have tried the directions step by step, resetting it, going to admin utility and network assistant, but, to no avail. I do have a secure network set up but airport express can't find it.
Questions: do I need to know all of the codes for the DNS as well as the server for Bellsouth(my ISP provider for my DSL)?
How do I "clear its palette" so that I can successfully reset airport express?
Not sure what to do next.
PowerBookG4 Mac OS X (10.4.2)

Is the indicator light lit at all. It seems quite a few 1 year old or so APX's have been dieing. Refer to this thread.
http://discussions.apple.com/thread.jspa?messageID=1439278&#1439278

Airport Express won't work without a router

I have a DSL modem and Airport Express. When I plug the Express directly into the modem I only get a flashing yellow light. However, when I install a D-Link Ethernet Broadband Router between the modem and Express, I get the green light. Hmmmmm. Any suggestions on how to eliminate the router?
G5 iMac Mac OS X (10.4.3)

Two possibilities:
1. you just need to reset your connection. Plug the modem into the Airport Express, and then pull power to both devices for five minutes. Then plug the modem into power and wait a minute, then plug the Airport Express into power - and it should show a solid green status light within a minute.
2. you have a DSL connection that requires use of the PPPoE protocol. If that is the case, your Airport Express must first be configure to handle the PPPoE connection (rather than using its default configuration to connect using DHCP).

Ethernet configuration Airport Express won't work - please help!

Similar Messages

Maybe you are looking for