Ethernet connection to an AirPort Extreme in extended mode?

Hi folks....
I just installed an airport express as a wifi extender for an airport extreme and everything is working fine. My reason for purchasing the extender is to provide an ethernet hook-up point for my "network ready" Denon AVR 2113ci receiver. I stress "network ready" because it is not "wireless" or "wifi enabled" but it does have an RJ45 ethernet connection to hardwire connect via ethernet cable to a network. Unfortunately, I can find no way to set up the airport express to allow me to do this? when I connect the receiver and attempt to set up the network connection I'm advised there is no network available. I purchased the Denon specifically because it was designed to use apple airplay so I don't think it's a compatibility issue? Thanks much for any advice!
Regards and Merry Christmas!

Suggest that you check to make sure that the Express is really "extending".
Temporarily, turn off the wireless on a laptop and connect it to the Ethernet port on the AirPort Express using an Ethernet cable that you know is working.
See if the computer can log on to the Internet. If it can, you know that you have a network signal at the Ethernet port on the AirPort Express.
What are your results?

Similar Messages

Airport Extreme in extender mode does not reconnect after main router reset.

I have an Airport Extreme 4th Gen (extender). set to extend the signal from an Airport Extreme 5th Gen (main). Whenever the main router resets (after reconfig, etc) the extender does not reconnect. I would have to restart the extender before it will connect again to the network. However, my Airport Express set to extend will automatically reconnect. Is this a settings issue? Please advise.

Ok, well I am hoping you are not doing a re-config of your 5'th gen all the time? This should only be done very rarely... we're talking like less than once a year for many people. Unless there's something else going on there, I wouldn't worry about it if you have to power-cycle the 4'th gen once in a few blue moons.

I'm having trouble with my iMac recognizing the WD My Book Live hard drive (ethernet) connecting to my Airport Extreme Base.

This is the first time I've tried to connect a hard drive to an ethernet port on the back of the base. I'm sure I need to do something with Airport setup but I'm not sure what to do.

Is this drive a network drive (use the ethernet port) or a local drive (use the usb port)
Ignore Shawn Grinter 2's post, until the type of drive is clear it is unwise to suggest anything.
What hard drive is this (make/model)
Your heading says MyBook Live, here is a picture of one,
Is this the drive you use?

How do I connect a PC via ethernet to my new Airport Extreme router?

I just replaced an old Actiontec router with a new Apple Airport Extreme router to work with my Verizon FIOS service. Connection to all Apple products via ethernet or wireless works OK, however I cannot get the PC up and running via its ethernet connection to the Airport Extreme. Any help would be much appreciated.

If your other devices are working then it is probably the PC's IP configuration.
First, make sure that the PC is actually connected to the Extreme by verifying the lights are on at the Ethernet ports on the PC and the Extreme.
If you are using DHCP to manage the IP addresses then make sure that the PC is configured to "Obtain IP Address Automatically" for both IP versions 4 and 6.
When I replaced my Linksys w/ an Extreme I forgot that I had a couple devices configured with static (manual) IPs. My old one used the "192.168.1.nn" and my Extreme defaulted to "10.0.1.nn". Once i converted all the static IPs to the correct subnet then all was good.

I am trying to hook up a second airport extreme to extend my network. Can I do this without having another ethernet connection?

I am trying to hook up a second airport extreme to extend my wireless network. Can I do this without having a second ethernet connection?

Yes. Apple's instructions to do this are here:
http://support.apple.com/kb/HT4259

Can multiple Airport Expresses be connected via ethernet to an Airport Extreme to extend a single WiFi Network?

I am a big fan of both the Airport Extreme and Airport Express. In my work environment, I need to create a good quality single wireless network around 2 large aircraft hangars and some offices at the perimeters. We have a good quality wired Cat5e ethernet network extended between the buildings and offices now. Is this possible and does it seem like a good practical solution? I think that 4 or 5 Airport expresses would easily provide good wireless coverage in the needed areas.

Can multiple AirPort Expresses be connected via ethernet to an AirPort Extreme to extend a single WiFi Network?
Yes, this will work just fine as long as any individual Ethernet cable run will not exceed much over 330 feet or about 100 meters.

Can I connect an external hard drive to one of the ethernet port of the airport extreme and access it from my Mac or PC?

Can I connect an external hard drive to one of the ethernet port of the airport extreme and access it from my Mac or PC?

If this hard drive is part of a NAS device, then yes it should be accessable from either a Mac or PC while connected to the AirPort Extreme Base Station (AEBS) by Ethernet.

I have a 3rd party hard drive with movies on it ,it is connected to my airport extreme. The AE is connected to my tv via ethernet cable. Can I stream my movies to the Tv ?

I have a 3rd party hard drive with movies on it ,it is connected to my airport extreme. The AE is connected to my tv via ethernet cable. Can I stream my movies to the Tv ?

Not without a player..
The AE is a dumb file server.. the hard disk you plug in is an even dumber hard disk.
There are no smarts in this setup.. not even DLNA. So the TV would have to be an extremely smart one to read raw files on a network drive.. none do that I know of.
A solution is WD live TV.. it can read files from just about any file source on network and play them to the TV.
Nothing apple makes will do that.. ATV is a streamer not a media player. Everything in the Apple world is tied up with itunes. So you must have a computer running itunes to use it.
You can download a more generic player for ipad, and put that as part of the network.. but you still need ATV to display the video.

Time Capsule Base via ethernet to an Airport Extreme to extend Wireless

I have set up a new Time Capsule dual band (TCBStn) as a base station (connected to the internet). I want to connect a new Airport Extreme dual band in a family room far away from the base via Ethernet. This family room has an Apple TV to which I want to stream video. I am not able to connect the AE via the Airport Utility as the Airport Utility does nor recognize the AE.

My recommendation is to configure your two base station as a "roaming" network. This will allow wired/wireless clients to connect to either and still be able to "see" each other for sharing.
Please start by powering-down all of your network components as follows:
o Power-down the modem, Time Capsule (TC), AirPort Extreme Base Station (AEBS), Apple TV (ATV), and the iMac. Note: The power-down order is not critical.
o With all of these components powered down, disconnect both the TC & AEBSn from the network, and then, perform a "factory default" reset on both to get them back to their "out-of-the-box" configuration.
o After both have been reset, remove them from power, and then, reconnect them as follows: modem > \[WAN port] > TC > \[LAN port] > \[WAN port] AEBSn, where ">" represents an Ethernet connection.
o Power-on the modem; wait at least 10-15 minutes.
o Power-on the TC; wait at least 5-10 minutes.
o Power-on the AEBSn; wait at least 5-10 minutes.
o Power-on the iMac.
o For now, leave the ATV powered-off.
In this configuration, both routers will be transmitting their own wireless network, each having a Network Name of something like: Apple Network NNNNNN, where the Ns represent the last six digits of their respective AirPort IDs.
Now, from the iMac, use the AirPort Utility (in Manual Setup) to access the TC to make the following configuration changes:
o Time Capsule > Base Station > Time Capsule Name = TC
o Time Capsule > Wireless > Wireless Mode = Create a wireless network
o Time Capsule > Wireless > Wireless Network Name = <enter the desired Network Name>
o Time Capsule > Wireless > Radio Channel Selection = Automatic
o Internet > Internet Connection > Connect Sharing = Share a public IP address
o Leave all the other default settings (for now).
o Click on Update to write the new configuration to the TC.
While still in the AirPort Utility, select the AEBSn, and then, make the following changes:
o AirPort > Base Station > AirPort Extreme Name = AEBSn
o AirPort > Wireless > Wireless Mode = Create a wireless network
o AirPort > Wireless > Wireless Network Name = <use the same Network Name that you created for the TC>
o AirPort > Wireless > Radio Channel Selection = Automatic
o Internet > Internet Connection > Connect Sharing = Off (Bridge Mode)
o Leave all the other default settings (for now).
o Click on Update to write the new configuration to the AEBSn.
You should now have a basic roaming network. Verify that your iMac can access the Internet while connected to either base station by wire or wireless. Please post back your results.

My westel modem (that I rent from my phone provider) quit working with the internet. My airport extreme seems to be working from the dsl (phone) connection through the westel, then through the ethernet cabled to the airport extreme. Do I need the modem?

My westel modem (that I rent from my phone provider) quit working with the internet. My airport extreme seems to be working from the dsl (phone) connection through the westel, then through the ethernet cabled to the airport extreme. Do I need the modem? Is the ethernet route less efficent that going throught the internet connection? If I don't need the westel modem; how do I make the dsl conection to the pone port in the wall? Thanks for help on this!

Ok, so are you saying that your Internet is or isn't working? Does it work if you plug your computer directly into your computer and bypass the router (make sure you power cycle the modem when you do this)? If it is working this way, then a new modem isn't going to solve a problem with your Internet not working. If it is going slow (try running a speedtest) then you need to call your phone company to have them take a look at why your Internet is slow. If it runs fine this way and then slows back down when you go back through your router there is something else going on. Try unplugging both the modem and the router, let the modem fully sign back in and connect to the Internet, after it gets signed in, plug your router in, and then after it boots up fully, try running the speedtest again...See if that helps any? Sometimes it's just an IP conflict that happens when the dynamic IP that is assigned by your Internet Service Provider changes and the change doesn't flow smoothly.

Can i connect a new airport extreme wirelessly to an existing airport extreme to extend range? if so, how?

My mother has an airport extreme hardwired to a modem for wireless connection in her home. she is trying to get a wireless connection in her shop, about 250 away and i was wondering if i can use another airport extreme wirelessly to connect to the wired extreme to extend the range

And, by clear line of sight Bob means nothing between the two but air space. Windows, walls, trees, bushes, etc. all act to attenuate the signal substantially, thus reducing the effective range.
If you are willing to spend lots of money you can purchase amplifiers that can extend the range. Check this out at QuickerTek.com.

HT4259 i connected two airport extremes by extending a wifi network. wifi seems weak...help

i connected two airport extremes by extending a wifi network. all my lights are green, and airport utility confirms connections are excellent. but the extended base station hasn't improved my wifi range in the area i set it up in.

If you have a Mac laptop handy, run the test that I have outlined below to find out if the remote AirPort Extreme is really extending the signal at all.
Here, I assume that both of your AirPort Extremes are the newer "square" versions....not the older "round" version.
Locate your Mac laptop close to the "main" AirPort Extreme
Hold down the option key on the Mac while you click on the fan shaped AirPort icon at the top of the screen
Look for the BSSID and jot down the last few characters
The BSSID is the AirPort ID of the AirPort Extreme
Now, move the laptop close the "remote" AirPort Extreme and perform the same test
If you see the same BSSID as the "main" AirPort Extreme, your Mac is picking up from the main AirPort...and the remote AirPort is not configured correctly to extend.
If you see a different BSSID near the remote AirPort, that indicates that the Mac is picking up a signal from the remote AirPort....which is exending the signal correctly.

I have an Airport Extreme which I'm using for a wireless network. Can I also plug in my iMac to one of the free ethernet ports on the Airport Extreme to connect to the Internet that way? Thank you.

I have an Airport Extreme which I'm using for a wireless network. (The wireless router is connected to a DSL modem.) Can I also plug in my iMac to one of the free ethernet ports on the Airport Extreme to connect to the Internet that way? Thank you.

Yes, you can.

I just bought a mac mini...can i just connect an ethernet cable to the airport extreme and set up the mini through an existing mac

I just took the mini out of the box and hooked it up to the airport extreme through a direct ethernet cable between the two. Can i find the mini and set it up through an existing mac that is also hard wired to the network? Help would be greatly appreciated.

Thank you for your response.. I don't have a monitor nor a wireless keyboard to use on the mac mini...apple salesguy at bb tells me that I can hook up the mini to the ethernet port of my airport extreme and find the mini using finder on my 27 inch mac.
that my regular mac would see everything on the mini and that i can proceed to set everything on the mini through my regular mac...
I am trying to purchase the server software from the app store and turn the mini into a server..
that is what i am attempting to do.

Can I use an airport extreme to extend the range of my wireless modem

Can I use an Airport Extreme to extend the range of my wireless modem?
At one end of my house I have a dual band wireless ADSL modem which provides my internet connection and I want to extend (improve) the wireless coverage to the other of the hosue where my Apple TV (2nd gen) is located. I have being trying to extend my wireless network with an Airport Extreme but so far without success. I can get the Airport to join the wireless network, but I suspect that it is only acting as another client and not actually extending the wireless range. There is a setting in the Airport configuration to "extend and existing network", however when I choose this option the Airport no longer connects to my existing wireless network and I am beginning to suspect that this fuction only works with another Apple device (Airport Extreme or Express).
Has anyone been able to extend the range of a third party wireless router / modem with an AirPort Extreme? If so, any advice that you can offer wold be appreciated.
Regards
Michael

Thanks Tesserax,
Your answer has confirmed my suspicions.
Option 1 from your suggested solutions is not a goer because the modem and Airport Extreme are in different parts of the house making it impractical to run a cable between the two devices.
I did try option 2 and bought a Netgear range extender, which according to Netgear it would work with my D-Link modem - not.
However I have managed to work around the problem (sort of) by using the Airport Extreme to create a wireless network between my iMac 27 and my Apple TV. The idea is that the iMac will act as a router between ethernet connected ADSL modem and the wirelessly connected Apple TV.
The good news is that I am now able to play the content from my iTunes library on my Apple TV without interruptions due to a poor wireless connection . Although the connection from the Apple TV to the internet is not working I think this is most likely just a configuration issue and for me it is not really a show stopper.

Ethernet connection to an AirPort Extreme in extended mode?

Similar Messages

Maybe you are looking for