"ethernet doesn't have a valid ip configuration"
Hi
I use an apple time capsule as a wifi router. It is wired to two other airport express routers to extend the range.
Everything has been working fine for months, but I shut down my PC (Windows 8.1) on Friday and started it up on Monday. On Friday I could connect to the internet in the normal way. On Monday it's not working.
I have told Windows to forget the network, then I connected to it again with the correct password. I get an error message "Ethernet doesn't have a valid IP configuration". I have also tried connecting using an ethernet cable but get the same result. I have checked my IPV4 and IPV6 settings to make sure that the IP address is obtained automatically, which they were and are.
There are many other devices currently connected to the wireless network and they are working fine (another windows PC, ipad, iphone). It is just this one PC that cannot connect.
To be clear, the PC was not turned on between Friday and Monday. This issue has just happened. It's possible that another device joined the network over the weekend so could the time capsule be "full" somehow?
I have tried turning the time capsule off and on, and also the internet router. And reset my PC's network adapter, and restarted twice already. Without any luck.
Would appreciate some help!
OK, have just "solved" this somehow. Having forgotten the network I was then entering the wrong wifi password. When I put the correct one in, I can connect to the network and use the internet.
The weird thing is that I never got an error message before telling me it was the wrong password. It appeared to be connecting. Also the ethernet connection should have worked surely, as that doesn't need any code.
Similar Messages
-
AirPort doesn't have a Valid IP Address after Moving
After moving to a new apartment, I've been having a lot of trouble with my AirPort.
At first, only my computer was able to connect, even though I kept getting warnings that it didn't have a valid IP address. No other devises, including other computers, were able to connect. Throughout this entire time, the airport light blinked yellow. Then, all of a suddent, the airport light went solid green, and now I can't even connect wirelessly. I've had a tech savy friend look at it, and I also tried a hard reset. Nothing works.
My building provides us with internet, including the Motorola modum (SBV5330 SURFboard) in my room. Under networks, it says my SirPort is connected and has the IP address of 10.0.1.3.
Can somebody help me?jschenmd wrote:
able to reach ISP support who made me aware that the IP address is purposely set for one router so can't be changed out without their involvement.
So your ISP has chosen to throw you into the "worst case" situation I mentioned above. I don't know why ISPs do that. If nothing else, it increases their support costs.
He also convinced me to keep the linksys router stating that it was still an excellent device and unmatched in quality. So, I guess I won't be changing to Airport! Any disagreement or benefit of the Airport over a linksys broadband router model wrt54gl v1.1 other than my being a fan of Apple products?
I have no experience with Linksys equipment, but I suspect that it's no better or worse than most. I also suspect that the support people at your ISP are guilty of recommending only what they know.
If you already have that AirPort Extreme base station, I'd tell those people to stop jerking you around and update their configuration to let you use it. -
Local area connection doesn't have valid ip
I have a Touchsmart 320-1030 that belongs to a friend. Everything was working fine then for no apparent reason connection to the internet was lost. They have contacted their isp and gone through all troubleshooting with them. All other equipment (ie laptops, phones, ect..) connect and work fine. The windows troubleshooter offers no help and says local area connection doesn't have valid ip is the reason it won't connect. This is true when trying to connect wired or wireless. I piddle with fixing computers as a hobby so they have asked me to see what I can do if anything. I have been Googling, reading, and trying everything I have found for three days and have had no luck. So I am hoping I can find some help here. I have never seen anything like this. It may be a hardware problem and I'm not smart enough to realise it. But I need to know that too.
System -
Touchsmart 320-1030
Win 7 Home Premium
4 gigs ram
What I have done -
Brought system to my house to see if it will connect, it does not so I am working on it here.
I have rebooted modem & router
Connected systen directly to modem bypassing router
Uninstalled and allowed windows to detect and reinstall network drivers
Updated network drivers
Updated Bios
Tryed to inatall orginal drivers from support but they wont install
I have changed from detect automaticly to use this ip in tcip ip4 and used ip I know is good to my router -
When I did this last thing the wireless did see my network but the network 2 thingy that it makes still won't connect even tho when I search for connections the list says I am connected to my network. The little thing by the clock says not connected. Also the ethernet adapter says unknown public network when I do that. Wireless says unknown public network or connection when I have it detect ip automaticly.
Network discovery will not turn on in homegroup, nether will the services assocated with it.
I have run tweaking . com firewall repair
I have uninstalled avast security, there are no other av or firewall programs
I have uninstalled bonjoir because I read that causes a conflict of somekind
I have run tweaking . com windows repair ( just in case because it looked liked the firewall repair was doing something).
I have run sfc /scannow and it found and fixed some things, ran it again and it found nothing.
I am pulling my hair out with this one. Please help.
Thanks for your time.SSCRSR1, welcome to the forum.
Wifi problems can be very difficult to diagnose. Here is the Wireless / Networking / Internet section for the computer. Read the Wireless area to see if there is any help with the problem.
Please click the "Thumbs up + button" if I have helped you and click "Accept as Solution" if your problem is solved.
Signature:
HP TouchPad - 1.2 GHz; 1 GB memory; 32 GB storage; WebOS/CyanogenMod 11(Kit Kat)
HP 10 Plus; Android-Kit Kat; 1.0 GHz Allwinner A31 ARM Cortex A7 Quad Core Processor ; 2GB RAM Memory Long: 2 GB DDR3L SDRAM (1600MHz); 16GB disable eMMC 16GB v4.51
HP Omen; i7-4710QH; 8 GB memory; 256 GB San Disk SSD; Win 8.1
HP Photosmart 7520 AIO
++++++++++++++++++
**Click the Thumbs Up+ to say 'Thanks' and the 'Accept as Solution' if I have solved your problem.**
Intelligence is God given; Wisdom is the sum of our mistakes!
I am not an HP employee. -
Can't set up Aiport Extreme - base station doesn't have valid IP address?
I recently bought an AirPort Extreme to replace my old Linksys wireless router. I am have a cable modem/router supplied by my cable provider and I was using the ethernet cable to connect the modem to the Airport. However, every time I attempt to configure it I get the following message: "Your Apple Wi-Fi base station does not have a valid IP address." I tried to call Comcast to see if there is something I need to get from them, but they want to charge me ~ $45 to enroll me in wireless tech support! Anyways, I'm at my wits' end - please help if you can!
Hello MrRuminator. Welcome to the Apple Discussions!
Each time I attempt to connect to the internet with the AirPort Extreme I run into "Base Station does not have valid IP address -- make sure your base station is connected to your broadband modem..." error. What's odd about this is the fact if I simply plug the ethernet cable back in the older Airport (like right now), I'm able to access the internet once again. Have tried powering off and resetting everything, to no avail.
It still sounds like your modem is not "recognizing" the new 802.11n AirPort Extreme Base Station (AEBSn).
Try the following, in order, until (hopefully) resolved:
1. If the modem has a reset switch, use it to reset the modem. Wait at least 5-10 minutes for the modem to initialize.
2. Remove power from the modem. If it has a backup battery, remove this as well. Wait 5-10 minutes. Replace the battery, and add power back to the modem.
3. Perform a complete power recycle of your network components as follows:
Modem/Router Power Recycling - Quick
o Power-off the modem, AEBSn, & computer(s); Wait at least 5 minutes.
o Power-on the modem; Wait at least 5 minutes.
o Power-on the AEBSn; Wait at least 5 minutes.
o Power-on the computer(s)
If this fails to get the modem to "recognize" the Internet router, then try the "Full" version.
Modem/Router Power ReCycling - Full
o Power-off the modem, AEBSn, & computer(s). (Wait at least 30 minutes. If possible, leave the modem off overnight.)
o Power-on the modem; Wait at least 15 minutes.
o Power-on the AEBSn; Wait at least 5 minutes.
o Power-on the computer(s)
4. Contact your ISP to have them perform a "modem reset." -
Today I tried to configure JAVA APM on a CentOS 6.4 server with tomcat6 installed through the normal RPM package. Adding this server to SCOM was no problem and it shows itself as a 'Deep Monitored Configuration'. The last part of enabling
JAVA APM fails. I have followed the following process:
1. Imported the JAVA APM MP's
2. Extracted the JAVA APM Files
3. Copied those files to my CentOS server
4. Added the JAVA_OPTS to my tomcat configuration file
5. Restarted Tomcat
When I look for the log file which needs to be created through the installation of the APM agent it cannot be find. When I look into my Catalina.out file I see the following errors:
Mar 05, 2014 7:05:16 PM com.microsoft.ManagementServices.APMAgent.Log.SystemLogger error
SEVERE: Java APM Agent initialization failed: SEAgent.config.xml does not have a valid event sender configured
com.microsoft.ManagementServices.APMAgent.Exception.ApmException: SEAgent.config.xml does not have a valid event sender configured
at com.microsoft.ManagementServices.APMAgent.AgentThreadManager.<init>(Unknown Source)
at com.microsoft.ManagementServices.APMAgent.AgentThreadManager.<init>(Unknown Source)
at com.microsoft.ManagementServices.APMAgent.Agent.Monitor.AgentContext.<init>(Unknown Source)
at sun.reflect.NativeConstructorAccessorImpl.newInstance0(Native Method)
at sun.reflect.NativeConstructorAccessorImpl.newInstance(NativeConstructorAccessorImpl.java:57)
at sun.reflect.DelegatingConstructorAccessorImpl.newInstance(DelegatingConstructorAccessorImpl.java:45)
at java.lang.reflect.Constructor.newInstance(Constructor.java:525)
at com.microsoft.ManagementServices.APMAgent.Agent.Startup.AgentContextLoader.loadContext(Unknown Source)
at com.microsoft.ManagementServices.APMAgent.Agent.Startup.Agent.premain(Unknown Source)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:57)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:43)
at java.lang.reflect.Method.invoke(Method.java:601)
at sun.instrument.InstrumentationImpl.loadClassAndStartAgent(InstrumentationImpl.java:382)
at sun.instrument.InstrumentationImpl.loadClassAndCallPremain(InstrumentationImpl.java:397)
Caused by: java.lang.reflect.InvocationTargetException
at sun.reflect.NativeConstructorAccessorImpl.newInstance0(Native Method)
at sun.reflect.NativeConstructorAccessorImpl.newInstance(NativeConstructorAccessorImpl.java:57)
at sun.reflect.DelegatingConstructorAccessorImpl.newInstance(DelegatingConstructorAccessorImpl.java:45)
at java.lang.reflect.Constructor.newInstance(Constructor.java:525)
... 15 more
Caused by: com.microsoft.ManagementServices.APMAgent.Exception.ApmException: Error registering MBean: com.microsoft.ManagementServices.APMAgent:type=COUNTER
at com.microsoft.ManagementServices.APMAgent.EventSender.MBeanEventLog.registerMetricMBeans(Unknown Source)
at com.microsoft.ManagementServices.APMAgent.EventSender.MBeanEventLog.<init>(Unknown Source)
at com.microsoft.ManagementServices.APMAgent.EventSender.MBeanEventLog.<init>(Unknown Source)
at com.microsoft.ManagementServices.APMAgent.AgentThreadManager.<init>(Unknown Source)
at com.microsoft.ManagementServices.APMAgent.AgentThreadManager.<init>(Unknown Source)
at com.microsoft.ManagementServices.APMAgent.Agent.Monitor.AgentContext.<init>(Unknown Source)
at sun.reflect.NativeConstructorAccessorImpl.newInstance0(Native Method)
at sun.reflect.NativeConstructorAccessorImpl.newInstance(NativeConstructorAccessorImpl.java:57)
at sun.reflect.DelegatingConstructorAccessorImpl.newInstance(DelegatingConstructorAccessorImpl.java:45)
at java.lang.reflect.Constructor.newInstance(Constructor.java:525)
at com.microsoft.ManagementServices.APMAgent.Agent.Startup.AgentContextLoader.loadContext(Unknown Source)
at com.microsoft.ManagementServices.APMAgent.Agent.Startup.Agent.premain(Unknown Source)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:57)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:43)
at java.lang.reflect.Method.invoke(Method.java:601)
at sun.instrument.InstrumentationImpl.loadClassAndStartAgent(InstrumentationImpl.java:382)
at sun.instrument.InstrumentationImpl.loadClassAndCallPremain(InstrumentationImpl.java:397)
Caused by: java.lang.reflect.InvocationTargetException
at sun.reflect.NativeConstructorAccessorImpl.newInstance0(Native Method)
at sun.reflect.NativeConstructorAccessorImpl.newInstance(NativeConstructorAccessorImpl.java:57)
at sun.reflect.DelegatingConstructorAccessorImpl.newInstance(DelegatingConstructorAccessorImpl.java:45)
at java.lang.reflect.Constructor.newInstance(Constructor.java:525)
... 15 more
Caused by: com.microsoft.ManagementServices.APMAgent.Exception.ApmException: Error registering MBean: com.microsoft.ManagementServices.APMAgent:type=COUNTER
at com.microsoft.ManagementServices.APMAgent.EventSender.MBeanEventLog.registerMetricMBeans(Unknown Source)
at com.microsoft.ManagementServices.APMAgent.EventSender.MBeanEventLog.<init>(Unknown Source)
at com.microsoft.ManagementServices.APMAgent.EventSender.MBeanEventLog.<init>(Unknown Source)
... 19 more
Mar 05, 2014 7:05:16 PM com.microsoft.ManagementServices.APMAgent.Log.SystemLogger info
INFO: Java APM Agent loading failed (Build: 1.10.100.15, Label: NotFromLabel, BuildDate: 20131112)
java.lang.reflect.InvocationTargetException
at sun.reflect.NativeConstructorAccessorImpl.newInstance0(Native Method)
at sun.reflect.NativeConstructorAccessorImpl.newInstance(NativeConstructorAccessorImpl.java:57)
at sun.reflect.DelegatingConstructorAccessorImpl.newInstance(DelegatingConstructorAccessorImpl.java:45)
at java.lang.reflect.Constructor.newInstance(Constructor.java:525)
at com.microsoft.ManagementServices.APMAgent.Agent.Startup.AgentContextLoader.loadContext(Unknown Source)
at com.microsoft.ManagementServices.APMAgent.Agent.Startup.Agent.premain(Unknown Source)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:57)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:43)
at java.lang.reflect.Method.invoke(Method.java:601)
at sun.instrument.InstrumentationImpl.loadClassAndStartAgent(InstrumentationImpl.java:382)
at sun.instrument.InstrumentationImpl.loadClassAndCallPremain(InstrumentationImpl.java:397)
Caused by: java.lang.InstantiationException: Monitor initialization failed: SEAgent.config.xml does not have a valid event sender configured
at com.microsoft.ManagementServices.APMAgent.Agent.Monitor.AgentContext.<init>(Unknown Source)
... 12 more
Does anyone have seen this error before? Can someone help me with this one?
Thnx,I'm running tomcat on a CentOS release 6.4 (Final) server. I installed Tomcat 6 through an RPM from the CentOS sources. I have installed Apache Tomcat/6.0.24 wit JVM version 1.7.0_09-icedtea-mockbuild_2013_01_16_18_52-b00, the JVM Vendor is Oracle Corporation.
My tomcat configuration needs to be done in '/etc/tomcat6/tomcat6.conf'
I installed the APM Agent in the path '/opt/apm/' with the rights 40755 (root/root). The files have the following rights:
-rw-rw-r-- 1 root tomcat 32046 Mar 3 15:38 apm_facade.jar
-rw-rw-r-- 1 root tomcat 244819 Mar 3 15:38 apm_monitor.jar
-rw-rw-r-- 1 root tomcat 38110 Mar 3 15:38 apm_producers.jar
-rw-rw-r-- 1 root tomcat 207006 Mar 3 15:38 asm-all-3.3.1.jar
-rw-rw-r-- 1 root tomcat 4157 Mar 3 15:38 ASM_Third_Party_Notices.txt
-rw-rw-r-- 1 root tomcat 241368 Mar 3 15:38 DispatcherStub.dll
-rw-rw-r-- 1 root tomcat 36880 Mar 3 15:38 pmonitor.config.xml
-rw-rw-r-- 1 root tomcat 2625 Mar 3 15:38 SEAgent.config.xml
-rw-rw-r-- 1 root tomcat 830 Mar 5 15:19 Starter.properties
The above rights are equal to the /etc/tomcat6 directory with the tomcat configuration files.
In the tomcat6.conf I have added the following entries:
#Microsoft SCOM APM
JAVA_OPTS="${JAVA_OPTS} -Djava.library.path=/opt/apm"
JAVA_OPTS="${JAVA_OPTS} -javaagent:/opt/apm/apm_facade.jar -Xbootclasspath/p:/opt/apm/apm_producers.jar -Xbootclasspath/p:/opt/apm/apm_facade.jar"
When I look into the running tomcat process I see the following:
tomcat 17401 1 0 Mar05 ? 00:00:39 /usr/lib/jvm/jre/bin/java -Djava.library.path=/opt/apm -javaagent:/opt/apm/apm_facade.jar -Xbootclasspath/p:/opt/apm/apm_producers.jar -Xbootclasspath/p:/opt/apm/apm_facade.jar
-Djavax.sql.DataSource.Factory=org.apache.commons.dbcp.BasicDataSourceFactory -Djava.library.path=/opt/apm -javaagent:/opt/apm/apm_facade.jar -Xbootclasspath/p:/opt/apm/apm_producers.jar -Xbootclasspath/p:/opt/apm/apm_facade.jar -Djavax.sql.DataSource.Factory=org.apache.commons.dbcp.BasicDataSourceFactory
-classpath :/usr/share/tomcat6/bin/bootstrap.jar:/usr/share/tomcat6/bin/tomcat-juli.jar:/usr/share/java/commons-daemon.jar -Dcatalina.base=/usr/share/tomcat6 -Dcatalina.home=/usr/share/tomcat6 -Djava.endorsed.dirs= -Djava.io.tmpdir=/var/cache/tomcat6/temp
-Djava.util.logging.config.file=/usr/share/tomcat6/conf/logging.properties -Djava.util.logging.manager=org.apache.juli.ClassLoaderLogManager org.apache.catalina.startup.Bootstrap start
My Starter.Properties looks like this:
# Jars to load by inner classloader.
# Use semicolons to separate the JAR entries
ClassPath=apm_monitor.jar;asm-all-3.3.1.jar;apm_producers.jar
# Path to pmonitor.config
MonitorConfigFileName=pmonitor.config.xml
# Path to SEAgent.config
AgentConfigFileName=SEAgent.config.xml
# Log file name
# Example for full-path location:
# LogFileName=c:\\tracelog\\apm-java-agent.log
# Example for relative path (to agent jar files):
# LogFileName=apm-java-agent.log
LogFileName=apm-java-agent.log
# Log level (SEVERE, WARNING, INFO, CONFIG, FINE, FINER, FINEST)
# A level of FINER or FINEST may expose Personally identifiable
# information (PII) in the log file. The levels below INFO are
# intended for debugging and diagnostic use only.
LogLevel=FINEST
The 'apm-java-agent.log' is not created on the system. The only logging is done in the catalina.out. When restarting tomcat I see the following entries in te log file:
INFO: Initializing Java APM Agent (Build: 1.10.100.15, Label: NotFromLabel, BuildDate: 20131112)
Mar 06, 2014 9:35:21 AM com.microsoft.ManagementServices.APMAgent.Log.SystemLogger info
INFO: Java APM Agent loading succeeded (Build: 1.10.100.15, Label: NotFromLabel, BuildDate: 20131112)
Mar 06, 2014 9:35:21 AM com.microsoft.ManagementServices.APMAgent.Log.SystemLogger info
INFO: Initializing Java APM Agent (Build: 1.10.100.15, Label: NotFromLabel, BuildDate: 20131112)
Mar 06, 2014 9:35:21 AM com.microsoft.ManagementServices.APMAgent.Log.SystemLogger warning
WARNING: Failed registering the COUNTER MBean
Mar 06, 2014 9:35:21 AM com.microsoft.ManagementServices.APMAgent.Log.SystemLogger error
SEVERE: Java APM Agent initialization failed: SEAgent.config.xml does not have a valid event sender configured
Mar 06, 2014 9:35:21 AM com.microsoft.ManagementServices.APMAgent.Log.SystemLogger info
INFO: Java APM Agent loading failed (Build: 1.10.100.15, Label: NotFromLabel, BuildDate: 20131112)
Hope this gives your some more background around my problem, I double checked the permissions.. -
HT1176 Initial Time Capsule backup on MacBook Pro that doesn't have an Ethernet port
I just got a 3TB time capsule and am trying to backup my MacBook Pro. The initial process is very slow, but my MacBook doesn't have an Ethernet port. How can I connect the time capsule to the MacBook Pro to make the initial backup go more quickly?
A very good investment to make would be......
Apple USB Ethernet Adapter - Apple Store for Business (U.S.)
Why Apple chose to leave off the most important port in networking is a mystery. -
Bootcamp Windows 7 Wireless Network Connection: No Valid IP Configuration
I just bought a new 13" MBP and have installed Windows 7 Ultimate via Bootcamp 5.0. I installed the Windows Support Software that I had previously downloaded via Bootcamp Assistant on Mac OS. Although the Wireless Network Connection asked for my network key and connects to the network, I cannot access the internet. The troubleshooter find this problem: "Wireless Network Connection" doesn't have valid IP configuration. I am using my old Dell computer and it is connecting to the wireless properly and my MBP can connect on Mac OS, so I don't think it's a router issue. Here are the things I have tried so far to resolve this issue, but none have worked:
Uninstalling the Broadcom Network Adapter driver, restarting the computer, and reinstalling
Repairing the Windows Support Software with the Bootcamp 5.0.5033 Support Software Update downloaded from www.apple.com
Uninstalling the Broadcom Network Adapter driver, restarting the computer, and reinstalling the driver from Bootcamp 5.0.5033
ipconfig /release gives an error about disconnected media.
ipconfig /all says:
Windows IP Configuration
Host Name . . . . . . . . . . . . : Alise-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
Ethernet adapter Local Area Connection:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Broadcom NetXtreme Gigabit Ethernet
Physical Address. . . . . . . . . : 68-5B-35-7C-FC-A9
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
Wireless LAN adapter Wireless Network Connection:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Broadcom 802.11n Network Adapter
Physical Address. . . . . . . . . : A8-BB-CF-1B-54-3A
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
Link-local IPv6 Address . . . . . : fe80::1d6a:752c:62e3:d01b%15(Preferred)
Autoconfiguration IPv4 Address. . : 169.254.208.27(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.0.0
Default Gateway . . . . . . . . . :
DHCPv6 IAID . . . . . . . . . . . : 313048015
DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-19-C6-A6-83-A8-BB-CF-1B-54-3A
DNS Servers . . . . . . . . . . . : fec0:0:0:ffff::1%1
fec0:0:0:ffff::2%1
fec0:0:0:ffff::3%1
NetBIOS over Tcpip. . . . . . . . : Enabled
Ethernet adapter Bluetooth Network Connection:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Bluetooth Device (Personal Area Network)
Physical Address. . . . . . . . . : A8-BB-CF-1B-54-3B
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter isatap.{C38C3280-5682-4E5A-A978-9DD1A96CDBFF}:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft ISATAP Adapter
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter isatap.{ABCE958D-5FDB-4D1E-86F5-ECF01B80E01F}:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft ISATAP Adapter #2
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter isatap.{749630EF-9B2E-4DF1-9B6F-B38A5237F81A}:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft ISATAP Adapter #3
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Please help!Did you find a solution for this? I have exaclty the same problem.
But I could temporarily solve it by setting an IP, gateway, dns etc manually. But that will only work in my current wifi-network.
I can't even get internet sharing from my iphone -
Hi, We are trying to get a client to communicate with the primary Config Manager Site System(MP/DP).
We have a Config Manager Client Template that was setup using this guide.
http://technet.microsoft.com/en-us/library/gg682023.aspx
We have a Client Cert on the primary site system server (primary config manager server) based on this template and it meets the requirements specified in this document
http://technet.microsoft.com/en-us/library/gg699362.aspx
Enhanced Key Usage value must contain
Client Authentication (1.3.6.1.5.5.7.3.2).
Client computers must have a unique value in the Subject Name field or in the Subject Alternative Name field.
SHA-1and SHA-2 hash algorithms are supported.
Maximum supported key length is 2048 bits.
The Cert that we generated for the client meets the same requirements and shows the exact same template id but has a different subject name and alternate name (which is the clients machine name).
With this setup, we still get the following error
Certificate [Thumbprint SOME THUMBPRINT] issued to 'CLientMachineName' doesn't have private key or caller doesn't have access to private key.
Both the site system and client have the same trusted root cert installed.
What are we missing or what can we check? Does the cert check process only need the client certs on both the site system and the client to be from the same template?
Here is a snippet of the clientidmanagerstartup.log
<![LOG[HTTPS is enforced for Client. The current state is 63.]LOG]!><time="15:02:32.057+300" date="03-12-2014" component="ClientIDManagerStartup" context="" type="1" thread="716" file="ccmutillib.cpp:395">
<![LOG[Begin searching client certificates based on Certificate Issuers]LOG]!><time="15:02:32.058+300" date="03-12-2014" component="ClientIDManagerStartup" context="" type="1" thread="716"
file="ccmcert.cpp:3833">
<![LOG[Certificate Issuer 1 [CN=THE_NAME_OFTHE_CA; DC=DOMAIN; DC=LOCAL]]LOG]!><time="15:02:32.058+300" date="03-12-2014" component="ClientIDManagerStartup" context="" type="1" thread="716"
file="ccmcert.cpp:3849">
<![LOG[Based on Certificate Issuer 'THE_NAME_OFTHE_CA' found Certificate [Thumbprint SOMETHUMBPRINT_1] issued to 'CLIENTMACHINENAME']LOG]!><time="15:02:32.082+300" date="03-12-2014" component="ClientIDManagerStartup"
context="" type="1" thread="716" file="ccmcert.cpp:3931">
<![LOG[Begin validation of Certificate [Thumbprint SOMETHUMBPRINT_1] issued to 'CLIENTMACHINENAME']LOG]!><time="15:02:32.082+300" date="03-12-2014" component="ClientIDManagerStartup" context="" type="1"
thread="716" file="ccmcert.cpp:1245">
<![LOG[Completed validation of Certificate [Thumbprint SOMETHUMBPRINT_1] issued to 'CLIENTMACHINENAME']LOG]!><time="15:02:32.085+300" date="03-12-2014" component="ClientIDManagerStartup" context="" type="1"
thread="716" file="ccmcert.cpp:1386">
<![LOG[Completed searching client certificates based on Certificate Issuers]LOG]!><time="15:02:32.085+300" date="03-12-2014" component="ClientIDManagerStartup" context="" type="1" thread="716"
file="ccmcert.cpp:3992">
<![LOG[Begin to select client certificate]LOG]!><time="15:02:32.085+300" date="03-12-2014" component="ClientIDManagerStartup" context="" type="1" thread="716" file="ccmcert.cpp:4073">
<![LOG[Begin validation of Certificate [Thumbprint SOMETHUMBPRINT_1] issued to 'CLIENTMACHINENAME']LOG]!><time="15:02:32.085+300" date="03-12-2014" component="ClientIDManagerStartup" context="" type="1"
thread="716" file="ccmcert.cpp:1245">
<![LOG[Certificate [Thumbprint SOMETHUMBPRINT_1] issued to 'CLIENTMACHINENAME' doesn't have private key or caller doesn't have access to private key.]LOG]!><time="15:02:32.086+300" date="03-12-2014" component="ClientIDManagerStartup"
context="" type="2" thread="716" file="ccmcert.cpp:1372">
<![LOG[Completed validation of Certificate [Thumbprint SOMETHUMBPRINT_1] issued to 'CLIENTMACHINENAME']LOG]!><time="15:02:32.086+300" date="03-12-2014" component="ClientIDManagerStartup" context="" type="1"
thread="716" file="ccmcert.cpp:1386">
<![LOG[Raising event:
instance of CCM_ServiceHost_CertRetrieval_Status
ClientID = "GUID:GUID";
DateTime = "20140312200232.090000+000";
HRESULT = "0x87d00283";
ProcessID = 6380;
ThreadID = 716;
]LOG]!><time="15:02:32.090+300" date="03-12-2014" component="ClientIDManagerStartup" context="" type="1" thread="716" file="event.cpp:706">
<![LOG[Failed to submit event to the Status Agent. Attempting to create pending event.]LOG]!><time="15:02:32.092+300" date="03-12-2014" component="ClientIDManagerStartup" context="" type="2" thread="716"
file="event.cpp:728">
<![LOG[Raising pending event:
instance of CCM_ServiceHost_CertRetrieval_Status
ClientID = "GUID:GUID";
DateTime = "20140312200232.090000+000";
HRESULT = "0x87d00283";
ProcessID = 6380;
ThreadID = 716;
]LOG]!><time="15:02:32.092+300" date="03-12-2014" component="ClientIDManagerStartup" context="" type="1" thread="716" file="event.cpp:761">
<![LOG[Unable to find PKI Certificate matching SCCM certificate selection criteria. 0x87d00283]
Thanks LanceHi,
It seems that there are something wrong with you PKI system.
Here are some steps for your reference.
SCCM 2012: Part II – Certificate Configuration
http://gabrielbeaver.me/2012/08/sccm-2012-part-ii-certificate-configuration/
Note: Microsoft provides third-party contact information to help you find technical support. This contact information may change without notice. Microsoft does not guarantee the accuracy of this third-party contact information.
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place. -
i have samsung corby gts3653 mobile and need to connect internet to mac through it but it doesn't have wifi and pcsuite for mac and how could i able to connect it, through gprs? GPRS is active in mobile but unable to link it with macbook pro(using lion os) can any one reply.
Until the MacBook Air was released and supported in 10.5, the Mac did not consider USB to be a valid Networking Protocol. So set the Mac with USB solutions aside.
To connect computer-to-computer, you typically need to be using an Ethernet crossover cable. Assigning the same address to two Ethernet devices is never the solution -- it gives a Network Conflict, just as you said.
If your Windows box has some mechanism for Sharing its WiFi connection over Ethernet, you would have to follow its rules. Whether that means Manually assigning an Ethernet Address in the same range or the PC will provide the Address, I do not know.
Best success may be running an Ethernet cable to your Wired/Wireless Base Station, or using a "gaming adapter" (Ethernet-to-Wireless no drivers required) connected to the Mac's Ethernet port to give it WiFi access. What is your Base Station {Cable, DSL, FIOS, Other} ? Ethernet cables can be up to 100 meters (an American Football Field). Often the Base Station can be moved closer for more convenience. -
HELP! 'Wireless Network Connection doesn't have va...
'Wireless Network Connection doesn't have valid IP configuration'.
The problem that I'm having on multiple devices gives me this message on my desktop PC. No devices in the house can connect to the internet apart from xbox systems weirdly enough. I have 3 xbox's in the house, two 360's and one xbox one which all connect perfectly fine.
No computers will connect and no mobile phones. The router is shining a blue light indicating that nothing is wrong. I have been searching for a solution for hours now and nothing has worked. If someone has a suggestion please let me hear it.Turn off smart setup.
http://bt.custhelp.com/app/answers/detail/a_id/44328/~/switching-smart-setup-on-and-off-on-the-bt-ho...
Split the wireless bands.
http://bt.custhelp.com/app/answers/detail/a_id/44798/related/1
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones. -
I bought a first gen Mac Mini for our daughter and it doesn't have internal airport adapter and was wondering if I got a airport express can I plug it in my daughters room and use it as a local router and just use the eithernet connect from it. Or would a airport extreme work better for this job. I have a wireless cable modem that we connect to. I also have a second question I have a iMac G4 that picks up the wireless signal but will not connect to it does it have to be a Apple airport for it to work or should it be able to connect to any broadcasted signal. Thanks for the help.
I'm not sure I quite understand. Do you wish to use the AEX to provide a wireless connection for a device that has an Ethernet port but no wireless capability of its own? You wish to use it in place of a wireless card that isn't internally installed? If so, the answer is, "Yes." It will work as a wireless access point. But you must have an extant wireless network because the AEX won't have an Internet connection when used in this way.
If you have an existing wireless network with a wireless router connected to your cable/DSL model or your modem is a wireless router as well, then the AEX may connect to it in bridge mode. Note that AEXs don't always play nice with non-Apple routers. Some work; others don't. -
Pages document "could not be read" bc. it "does not have a valid format"
The document in question was properly saved and Pages was not open when my computer hung as it was shutting down. MS Word would not quit or force-quit and I had to hard restart the computer. When I later tried to open this Pages document, which I had been working on before Word froze, Page would not open it and responded with the error message: "This document "document_name.pages" could not be read. This document does not have a valid format." When I looked at the document in question I noticed that its file size was 0KB. I have no idea why this happened, but I suppose it has to do with my computer not shutting down properly and perhaps with Word freezing. If I repair my drive permission, re-index it, anything, will it help? Just a note on the status of this machine: spotlight stopped working earlier this morning and I was waiting to finish this document before repairing disk permissions and trying to fix that issue with Spotlight.
In the meantime I have tried various fixes. First I tried to change the file ending to .zip, unpack it and open it. Then the same, but this time I tried to view package contents. It doesn't show up in the contextual menu as even having a package to show the contents of. The file is effectively empty, but I don't know where the contents went! The funny thing is that the MS Word doc was recovered automatically. Is it possible that Pages doesn't have an auto-recovery mechanism?
I need this file urgently, or at least the text in it. It is the bibliography of an important paper due tomorrow at 5 pm.Any advice or suggestions would be greatly appreciated.
BTW, I have used a file-recovery program in the past. It is called "Stellar Phoenix" and it worked wonderfully to find a Word doc that I accidentally deleted. It can't find .pages document though. In order to do so, I would need to tell the program what the average file size is, as well as the header information as follows. "Header (in hexadecimal)" "At Offset (in decimal)". I have no idea what this means, but if I could insert it, perhaps it could find the lost data. Should I have it search for .pages, .zip, .xml? I'm at a loss, but I know that it doesn't recognize .pages. In the meantime, I sent a support email to them and will see what happens.
Thank you for your help.
DavidI can't respond before.
When the system say that your file size is 0KB, it means that nothing was saved. Only a file descripto exists.
So, there is nothing to recover.
Given the time the system crashed, you may have :
(1) a simple descriptor with nothing written
(2) a folder with every or only some of the required files.
In this case, Phoenix is useless : it's unable to revive a folder.
(3) a flatfile (a compressed version of the folder named above). It's only this kind of file which Phoenix may revive.
With a bit of luck, Phoenix would be able to revive the index.xml file which was in the original folder created in the temporary folder.
This file starts with :
<?xml version="1.0"?><sl:document xmlns:sfa="http://developer.apple.com/namespaces/sfa"
or
<?xml version="1.0"?>
<sl:document xmlns:sfa="http://developer.apple.com/namespaces/sfa"
The minimal size for a Pages index.xml file is : 520038 bytes.
If you retrieve the index.xml file, we may try to rebuild an usable package.
Ask the recovery tool to transfer the recovered file on an other media.
If the document embedded pictures, the index will give their path and their size which may be useful to recover them.
Yvan KOENIG (VALLAURIS, France) lundi 1 novembre 2010 10:27:44 -
I just bought a new IMAC and I want to install the Office Mac 2011, but it doesn´t have a CD unit. How can I do it?
Howard has the easiest answer. Or at least, cheapest, since you don't need to purchase an external CD/DVD drive.
The "demo" software from Microsoft's site is exactly the same as what's on the DVD. Install that and activate it with the key in your software box.
From Microsoft's site:
How do I install Office for Mac 2011 if my Mac doesn't have a DVD drive?
There are two options for installing Office for Mac if your Mac doesn't have a DVD drive.
Option 1: Convert your Office for Mac 2011 trial. To convert a trial version, you must have a valid product key. The product key will convert your trial into a fully licensed version of Office for Mac.
1. Locate the 25-character product key in your product package or confirmation email.
2. Open any Office for Mac application, like Word, PowerPoint, or Excel.
3. On the first screen of the Microsoft Office Setup Assistant, click Enter your Product Key.
4. Enter your product key and complete the installation instructions.
Option 2: If you have not previously installed the trial version, you can download Office for Mac from the Office for Mac website. To download, install, and activate the software you must have a valid Office 2011 product key.
1. Locate your 25-character product key found in your product package or confirmation email.
2. Go to www.officeformac.com/download
3. Click Get Started to start the download process.
4. When prompted, enter your 25-character product key and select your product language.
5. When prompted, sign in with your Windows Live ID or sign up and create a new Windows Live ID account.
6. After you enter your Windows Live ID, you will see a link to download the software. (You will also receive a confirmation email with a link to your My Account page if you prefer to wait and download your software at a later time.)
7. Click Download Now to start the download.
8. Save the file to your desktop. Do not change the file name.
9. When the download is complete, double-click the .dmg file icon on your desktop. This opens the Installer application in Mac OS X.
10. Follow the instructions in the installer screens to complete your installation. -
Time Capsule does not have a valid IP address
We have 2 computers in our home office: a Win 7 desktop and an iMac.
We have cable internet; the cable modem (Toshiba PCX2500) is plugged (ethernet) directly into the Time Capsule, which we use as our router to the two computers (also by ethernet).
The wireless functionality of the Time Capsule has been turned off.
We’ve been using the Time Capsule like this for the past 18 months (we purchased it new) without any problems.
Last month, however, we began losing our internet connection regularly (about 3-4 times per day) and getting the dreaded golden flashing light (as opposed to solid green) along with the error (paraphrasing here) “the Apple Wi-Fi does not have a valid IP address.”
We hadn’t made any changes in our hardware; it just showed up out of the blue.
After contacting our ISP, we were advised to unplug the cable modem for about 30 seconds, then plug it back it. Most of the time this worked; if not, we had to “cycle” the Time Capsule as well.
We’re now having to do this about 4-5 times per day.
Sometimes the Time Capsule’s status light is still green when we have no internet connection. Out of the blue the connection just isn’t there.
We “cycle” the cable modem and we’re back in business every time.
Additionally, when we actually do have an internet connection, the speeds fluctuate wildly. We’re paying for 15 Mb service; as of the past 4-5 weeks, we get 15Mb about 50% of the time. The other 50% it generally averages between 3Mb and 6Mb.
The ISP’s tech support (we’ve contacted them no less than once a week since this started) swears up and down that it’s the router, not their signal or their equipment in any way. They deny all culpability.
We even had the ISP’s repair people come out on an occasion about 10 days ago to test the signal strength; they reported no problems. “You’ve got great signal strength to your home…” were the exact words.
Similarly, after calling Apple on 2-3 occasions, we get the exact same response: “It’s not the Time Capsule router, it’s your ISP.”
The last Apple technician we spoke with (yesterday) said, “I’ve been doing wireless/Internet tech support for years and I can guarantee you – 100% -- that it’s a ‘DNS caching’ issue. I’m 100% positive that’s your problem, and I’m also 100% positive it’s your ISP’s fault.”
After contacting the ISP again we were informed that they don’t have any such caching problems.
We’re tired and frustrated! Please help.I would suggest running the network via a pc for the day.. pick either your Mac or win7 pc.. you will need to do a bit of fiddling.. even better would be to just borrow a router. Or buy one on a 7day return .. !! Beg borrow.. don't steal. Just get a router other than TC. it won't take long to determine if the TC is the issue.
IMO at 18months you are suffering failure of the TC power supply. early days but it is showing signs of delinquency. And will get worse. But another router will show it up.. if the PC has dual ethernet cards you can run ICS.. or same sort of thing on the imac to the wireless .. ie the PC or Mac becomes the router with direct connection to the cable modem. Then share internet from there.
Once you do that for a day or two, you will quickly be able to track down if the issue is cable service/modem or the TC as router. -
Office 365 MP Config Issue - Account doesn't have administrator permissions
SCOM 2012 R2 RU3 | Windows Server 2012 R2
I just configured this MP in the environment using the following references:
Office 365 MP Operations Guide
Reference 1
Reference 2
In addition I've configured the Office 365 Subscription Proxy secure reference.
When looking in the SCOM console I only see one error:
Source: Office 365 Monitoring
Full Path Name: Office 365 Monitoring
Alert Monitor: Office 365 Connection State monitor
Created: 1/14/2015 4:42:56 PM
Account doesn't have administrator permissions
Knowledge: View additional knowledge...
Summary
The monitor oversees the availability connection to Office 365 API EndPoint.
Causes
An error state is caused by having issues with connecting to Office 365 API EndPoint. It can be caused by:
• Issues with global connection to Office 365 API EndPoint
• Credentials for Office 365 Subscription's account are not correct
• Office 365 Subscription's account is not allowed to getting data from Office 365 EndPoint API
I've verified that the account is able to log into the server, has the _identifier, and global admin permissions in the Office 365 admin console.
Wondering if there's anything I may have missed.
Any responses appreciated.Verify that a proxy account is domain account.
Also check below office 365 MP Guide
http://www.microsoft.com/en-us/download/details.aspx?id=43708
Please remember, if you see a post that helped you please click "Vote As Helpful" and if it answered your question, please click "Mark As Answer"Mai Ali | My blog:
Technical | Twitter:
Mai Ali
Maybe you are looking for
-
Change file name with oreilly servlet
I am using oreilly servlet package and I want to change the file name to the file I am uploading, is this possible ? How ? Thanks. here I post the servlet code: package com.reducativa.sitio.servlets; * DemoParserUploadServlet.java * Example servlet t
-
Is there an app that bundles all things pertaining to a contact , photos, text , notes, etc ???
I need a way to access everything about client data without jumping from app to app.
-
Hi all will this effect the performance of the Program, and is there any alternative for this to fetch the data. i am very much confused abt why it was used. LOOP AT t_prd_data INTO wa_prd_data. SELECT aaplzl bvgw03 bvge03 bbmsch INTO (wa_plpo-aplzl,
-
How to read ABAP STACK of another report
Hi, I wish to read the ABAP STACK of another report which may or may not be running in debugging mode. First of all is it possible. if yes then pls reply. Thanks
-
Install adobe flash player for my samsung galaxy 3 phone
Please i need to install adobe flash player for this phone samsung galaxy 3