Ethernet seems to work when booted from Leopard DVD--Not anytime else

Ok. Here is the deal. iMac G5 connected via ethernet cable to router. It will not connect. The airport works fine. I unplug the same cable and plug into macbook pro--it works just fine. Plug it back into iMac.
In network utilities when booted from the disk--I can ping away just fine. So--in network preferences when I boot it up again I attempt to put the IP address, subnet, router yada yada yada in manually and after about twenty five seconds of the program chewing on it--it crashes. Over and over again. Airport works just fine. PowerBook and Mac Pro connected to same network---all check out.
Any thoughts?

Hi,
The internet port is meant for modem, and ports 1,2,3,4 are meant for computers.
After making proper connections reset router for 1 minute, and rebbot it.
Now run easy connect program for configuring router.

Similar Messages

Problem: installed new hard drive but can´t boot from leopard dvd

So I just installed a new hard drive in my ibook G4. At first I started up the computer using the leopard DVD I had purchased. Got to Disk Utility and after a few seconds in the spin wheel came up and froze. So, I shut the computer down and when I tried to boot it again from the DVD I wouldn´t even reach the apple screen. Tried it a few times unsuccessfully.
As an alternative I just tried booting the comptuer using the original CD and it did read it.
I am currently at the installer page but I am concern about installing the old CD as I really would like to run the leopard dvd 10.5.
Is it that my ibook g4 can´t be booted from leopard dvd?
Please advise. thanks!!

OK, so I decided to leave my computer resting all night and give it a new try this morning.
This morning I was able to boot from the Leopard DVD, so I don´t really think it is a problem with my superdrive. Started to format at 32 minutes to complete. Then towards the 10th minute the spinning wheel appeared, I heard the fan running, then it stopped and then I heard the superdrive making some reading noises. Then all noises stopped and now the spinning wheel continues..not sure what to do now.
In the meantime, I wanted to share also another problem that I´ve been having for quite some time which I don´t know if it is related to my current problem. It is with the computer power:
- I´ve been experiecing load surges that take my computer from 100% to 1 or 0% and then goes to sleep or shuts down. The same thing happens when I am charging the computer.. it starts charging and showing 2 or 3% charge and then jacks up to 100% in minutes.
- My computer also makes like a slight humming noise sometimes when the ring around the power cable is in orange color, so I move it around until it stops. When I do that sometimes it goes from orange to green eventhough it is not fully charged. There has been times that under green it appears to be charging (battery charging icon on desktop shows up), and other sometimes like right now when it is in green color and the battery icon on the desktop says ´99%´. Weird enough, once I get the cable in a certain position it enables the battery to charge, if I keep it without moving it, the load surges disappear (at least for some days).
Should I try resetting the PMU? I´ve not done it because I don´t know what consequences it may have.
NOTE: When I bought the computer I never calibrated my battery because I was (and still are) clueless when comes to computer technicalities. I tried using a different power adapter and get the sample problem.
Below is the information I get from coconut battery:
My battery is in its 256 load-cycle. current battery capacity 58512mAh (original battery capacity: 4400 mAh).
The last system profiler I was able to pull shows:
Battery Information:
Charge Information:
Charge remaining (mAh): 58320
Charging: No
Full charge capacity (mAh): 58512
Health Information:
Cycle count: 256
Battery Installed: Yes
Amperage (mA): 0
Voltage (mV): 16250
System Power Settings:
AC Power:
System Sleep Timer (Minutes): 15
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 15
Dynamic Power Step: Yes
Reduce Processor Speed: No
Automatic Restart On Power Loss: No
Wake On AC Change: No
Wake On Clamshell Open: Yes
Wake On LAN: Yes
Wake On Modem Ring: Yes
Display Sleep Uses Dim: Yes
Battery Power:
System Sleep Timer (Minutes): 5
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 5
Dynamic Power Step: No
Reduce Processor Speed: Yes
Automatic Restart On Power Loss: No
Wake On AC Change: No
Wake On Clamshell Open: Yes
Wake On Modem Ring: No
Display Sleep Uses Dim: Yes
Reduce Brightness: Yes
Hardware Configuration:
Clamshell Closed: No
UPS Installed: No
AC Charger Information:
AC Charger (Watts): 26
Connected: Yes
Charging: No
Any help is greatly appreciated.
Thanks a bunch!!!

Help: Cannot boot from leopard disc anymore, everything else fine

I was working on an ibook and messing with it in firewire mode and was going to install leopard on it that way from my macpro. (just letting you know the context)
I tried to restart my machine(mac pro) and boot leopard both by pushing C and by running the installer.
I get the "You need to hold the power button panic message" everytime I do this. I unplugged external devices and tried this also and it has the same problem.
I cannot boot from the dvd anymore. If I eject the disc, osx loads normally.
Any ideas what I can do? (I have tried safe boot, pram clearing and hold option on boot to check options)
Here is the kernel panic when it finally loads into osx.
here is the kernel panic log when it reboots into OSX
Sat May 17 14:13:09 2008
panic(cpu 1 caller 0x001A7BED): Kernel trap at 0x894ec373, type 14=page fault, registers:
CR0: 0x8001003b, CR2: 0x00000018, CR3: 0x00df8000, CR4: 0x00000660
EAX: 0x00000000, EBX: 0x00000000, ECX: 0x00000000, EDX: 0x0a5a1004
CR2: 0x00000018, EBP: 0x817c3bc8, ESI: 0x0a4c5c00, EDI: 0x0a4c5c00
EFL: 0x00010246, EIP: 0x894ec373, CS: 0x00000008, DS: 0x0a3c0010
Error code: 0x00000000
Backtrace, Format - Frame : Return Address (4 potential args on stack)
0x817c39d8 : 0x12b0e1 (0x4555b4 0x817c3a0c 0x133238 0x0)
0x817c3a28 : 0x1a7bed (0x45e568 0x894ec373 0xe 0x45dd24)
0x817c3b08 : 0x19e517 (0x817c3b20 0xa83c980 0x817c3bc8 0x894ec373)
0x817c3b18 : 0x894ec373 (0xe 0x48 0x10 0x10)
0x817c3bc8 : 0x894db540 (0x0 0xa83c980 0xa4c5c00 0x1)
0x817c3c08 : 0x78d45139 (0xa4c5c00 0x1 0x0 0x13)
0x817c3c68 : 0x78d3e940 (0xa4c5c00 0x2407 0x817c3d2c 0xa4c5c00)
0x817c3c98 : 0x40c515 (0xa4c5c00 0xacd8130 0xacd8130 0x0)
0x817c3ce8 : 0x437535 (0xa4c5c00 0xacd8130 0xacd8130 0x0)
0x817c3d48 : 0x18c8aa (0xa4c5c00 0xacd8130 0x0 0x0)
0x817c3db8 : 0x12d165 (0xa525c78 0xaa76b90 0x817c3df8 0x11ee04)
0x817c3df8 : 0x126247 (0xa525c00 0xa2f9254 0xaad84b0 0x0)
0x817c3f08 : 0x196afc (0x817c3f44 0x0 0x0 0x0)
0x817c3fc8 : 0x19eb34 (0xab382a0 0x0 0x1a10b5 0xa63f208)
No mapping exists for frame pointer
Backtrace terminated-invalid frame pointer 0xbffff378
Kernel loadable modules in backtrace (with dependencies):
com.apple.NVDAResman(5.1.6)@0x894d8000->0x89704fff
dependency: com.apple.iokit.IONDRVSupport(1.5)@0x78cc5000
dependency: com.apple.iokit.IOPCIFamily(2.4)@0x78ac0000
dependency: com.apple.iokit.IOGraphicsFamily(1.5)@0x78d36000
com.apple.iokit.IOGraphicsFamily(1.5)@0x78d36000->0x78d51fff
dependency: com.apple.iokit.IOPCIFamily(2.4)@0x78ac0000
BSD process name corresponding to current thread: WindowServer
Mac OS version:
9A581
Kernel version:
Darwin Kernel Version 9.0.0: Tue Oct 9 21:35:55 PDT 2007; root:xnu-1228~1/RELEASE_I386
System model name: MacPro1,1 (Mac-F4208DC8)

I really appreciate everyone's help.
I am certainly not above taking the machine in but I will say this.....
I have been building and working on PC's for 15-20 years. I have never once used or had the need for a repair shop. It is my hobby. I recently switched to osx to give the mac a try and I love it.
I will say that vista/xp has four times as many problems but at least i can fix whatever comes my way hardware or software.
Any more ideas how to settle this without making my first trip to the repair shop ever?...
Chad

BRAND NEW Mac Pro won't boot from Leopard DVD, kernel panics!

I just received my brand new Mac Pro today. It's a BTO machine with the upgrade to the NVIDIA 8800GT, a second optical drive and a Mac OS X Server license. The system has Mac OS X server installed on the default 320GB drive. I decided to use the server license as a virtual machine running in Leopard client. So, I installed 2 new 500GB Seagate 7200.11 (Retail) drives in the machine, zeroed them out in prep for installing Leopard client.
At this point, I pop in a freshly-purchased retail copy of the Leopard DVD and restart. When I try to boot from the DVD and install Leopard to one of the new Seagate drives, I get kernel panics - need to restart the machine. Also tried booting from the Mac OS X Server DVD and this too only caused kernel panics. The DVD's read perfectly from within Mac OS X Server and boot from hard disks is flawless.
I spent an hour on the phone with a level 2 tech at Apple - Tried swapping out the RAM and moving around the DIMMS to no avail. I am at a loss to what this could be. Seems to be a hardware issue and the tech thought it was likely a problem with one of the memory risers but couldn't send replacements. Anyone else with a similar issue?
This is my first Mac and it looks like this Mac Pro is going back for an exchange and I'll have to wait yet another 10-12 days for a replacement to arrive. Bummer.
Am I missing something simple here? Does this seem to be a hardware issue?
If anyone has any ideas before I ship this one back, please write!!!

New Mac Pros will not install the Leopard retail disc. They will only install the Leopard disc which shipped with them labeled Mac Pro. That has always been true. Macs can only boot the system that ships on DVD in the box that came with them, and newer retail releases. They can never boot from an older retail release than what shipped in the box.

IMac can't/won't boot from Leopard DVD

My 1GHz G4 iMac can't or won't boot from the DVD, although I know the media is good.
I get stuck on the grey screen, the rotating bug stops rotating after about 5 minutes.
It will still boot from the hard disk fine, and will boot with other DVDs as well. Hardware diagnostics check out fine.
I did try single user mode, it will get there OK.
Verbose mode spits out a lot of messages (who knew? - lol), but nothing that seems to point to any one issue. It too stops spitting out messages after about 10 minutes.
Any ideas?

I did try the clicking the mouse thing just for the heck of it... no joy.
I do see a few other threads like this one, so I'm not alone on this.
The error messages I see are (not going to type them out all the way):
launchd[1]: Failed to count the number of files in /System/Library/StartupItems no such file or directory
Then a bunch of mDNSResponder errors, also saying either no such file/directory or invalid destination port.
Then a message saying Folder Manager is being asked to create a folder (cach) while running as uid 0
Then Cannot use ATS Persistent Store - switching to old FODB cache code
kextd[47]: root filesystem is read-only; skipping kernel link data generation
followed by a couple of errors from configdp[41]
Then nothing....
Still stuck...

Extensions still work when calling from outside but not in listed in DN

Hello,
There are 3 extensions that still work when calling from the outside, but they don't reside in the DN listing. Where could they still exist? Using Cisco Unified CM 8.5.1.
Thank you for any assistance!

Review you dial plan and also the unassigned DNs, they might not exist as an exact match, but maybe in something with wildcards.
You can use DNA to search for them.
HTH
java
if this helps, please rate
www.cisco.com/go/pdihelpdesk

Error code 5 when booting from CD/DVD - Equium A200

I am trying to boot from CD/DVD and get the message: Cannot boot from CD - Code 5
Using a Windows Vista Home boot-cd.
The CD/DVD-station is ok. Have tried another station.
Have also tried another HDD.

Generally speaking you can use original Microsoft installation disc for OS installation. I have done this numerous times and have never noticed such errors and I have done this on different notebooks. One of them was Satellite A200. it is absolutely the same as your Equium.
My question: do you use original Microsoft installation disc or some own creation?
Put error code 5 in Google and you will find interesting articles about this.

2008 MacBook Pro won't boot from Leopard DVD or Target Disk

Yesterday I was working on my MacBook Pro. I use FontExplorer to manage fonts. I ran the conflicts diagnostic looking for missing font files, which returned about 200 results (I was expecting this). I've moved the fonts installed by Adobe/Microsoft out of my fonts folder in my user library (user library, not system). For some reason the computer started to become very slow, to the point of beachballing. The freezing seemed to start and stop. I was able to close FontExplorer and Illustrator without force-quitting. I tried to shut it down gracefully at that point but it froze up again, so I hit the power button to force a restart. It started up but now it hangs on the gray screen right before the Apple logo. The logo doesn't come up, I can hear the drive spinning as normal but it doesn't do anything.
I've tried booting from a retail copy of the Snow Leopard, but it doesn't work. I can hear the disc spin up in the DVD drive as though the computer is about to read it, but nothing happens. It just stays on that same blue screen. I've tried booting my MBP in Target Disk mode from my iMac. The target disk icon appears, however it just sits in the middle of the screen and my drive doesn't mount on the iMac. I've noticed now that the white status light on the front of the MBP (on the latch) doesn't come on, and if I cover the speakers the backlight doesn't turn off.
What do I do now? I have an enclosure I could use to try and boot the MBP's drive from, but I'm running out of options. I'm really starting to worry about my data. I have a major school project that's already late which is on there, and I don't have a recent backup. If I don't hand it in... let's not go there. I don't understand how this could happen; I take very good care of my computer, I turn it off when it's not in use, and I run Cocktail on it once a day which does a SMART status check.
Help?

sig,
The first thing I tried was booting from the install disk. The 2008/2009 MBP's aren't able to boot from a retail DVD of Snow Leopard, which is why I ended up using the original hardware-specific install disk that shipped with my computer. That didn't boot either. I was able to view the drive in Disk Utility when it was in the enclosure, but the partition with my data on it would not mount. I attempted a repair disk on the drive but that failed. It wouldn't mount in Terminal either. I considered trying to rebuild the volume catalog using TechTool Pro but there's the possibility that could actually make things worse. So I've taken it to the repair shop. They're running it through DiskWarrior overnight, last I heard there were 60-something thread errors. Yesterday my SMART status was fine, today my drive is dead. What happened? Hoping for the best (but expecting the worst).

G5 Black & white video when booted from install DVD

It has been years since I installed 10.5 on our G5 so I can not remember if this happened back then but think it did.
When I boot from an install DVD (both the original G5 DVD with Tiger and the MacOS Leopard DVD) the video output drops to 1-bit (dithered black & white) which makes it very hard to discern the text on the shaded buttons in the GUI. The video card is fine - when I hold down the Option key on boot to select the DVD the video is full-color, but as soon as it switches to running from the DVD the video becomes low-rez dithered b&w.
Anyone else see this issue and suggestions on resolving it? The display is a Dell 17" wide model. I don't have another display that is easily swappable to see if it's a problem with it or the Apple DVI-to-VGA adapter.
The G5 tower is a first-generation 2x2 (2CPUs, 2GHz) with 2 DVI ports on the video card (can't recall which card I ordered back then).

Great to hear, thanks for the report!
I suspect what happened, was that the Install also changed some PRAM or NVRAM setting, those are where number of colors are held.
Some earlier Macs store these settings in PRAM:
Status of AppleTalk
Serial Port Configuration and Port definition
Alarm clock setting
Application font
Serial printer location
Autokey rate
Autokey delay
Speaker volume
Attention (beep) sound
Double-click time
Caret blink time (insertion point rate)
Mouse scaling (mouse speed)
Startup disk
Menu blink count
Monitor depth
32-bit addressing
Virtual memory
RAM disk
Disk cache
http://support.apple.com/kb/ht1379

MacBook Pro Won't Boot from Leopard DVD

My brother's MacBook Pro (2009 13") won't boot from the Leopard install DVD. Here is what happened:
- I tried to do Bootcamp on it. I installed Windows 7 but realized that there were no Bootcamp drivers for that.
- Deleted Widnows 7 and put the XP install disc in. Somehow, it formatted my Mac partition instead of my Windows partition.
- Now that the MBP was only running Windows XP, I connected it to my iMac in target disk mode and wiped it (GUID, one Mac OS Extended (Journaled) partition).
- I tried to put the Leopard (10.5.0) install DVD in there so I can restore from the Time Machine backup, and it sees it when I hold option at bootup but refuses to boot from it.
- I reset the PRAM and tried again, no luck.
What is going on here? Does it have to do with the fact that it was doing Bootcamp? I either want to boot from the disc or somehow restore from Time Machine some other way. I can use another computer (my iMac) if I need to.

Haha yeah, I posted right before. The thing I'm wondering now: Does this mean that a Mac that came with Lion cannot be downgraded to Snow Leopard? Well, I'll save it for another question if I ever cross that bridge.
Limnos wrote:
Just so we know, this is the original OS disc that came with this computer? Even if you're trying to use a retail installer disc I am not sure those came out the the sufficient sub-version required to boot the computer (I think it needs at least 10.5.7 but don't have the specifics of your model).
Edit: I guess I'm a slow typist.

PowerBook 17 crashes consistently, even when booted from Tiger DVD

We have a new PowerBook 17 that has started giving us problems in the last day or so. It will hang after running for a few minutes. This is a consistent problem - it doesn't go away for an hour, or a day - if the machine is running, it will hang. There is no kernel panic, no dialogue box, the trackpad, mouse, etc. simply stop responding (the clock freezes too, so I know the system is hanging up - not just input devices).
I've managed to run throught most of the normal trouble-shooting methods, I say "managed" because the machine froze when I was booting into single user mode. So I went to the Tiger DVD that shipped with the laptop. Upon getting to the language selection dialog box - it froze again (no mouse, keyboard activity, etc.). Eventually, the machine did boot from the startup DVD - and I ran disk utility. Of course it found no problems with permissions or the disk because this is apparently hardware related, no?
That being said, an archive and install will probably do us no good. But would Tech Tools (came with our AppleCare) manage to at least spot a Hardware issue? At this point, the only thing I haven't done is removed the third-party RAM we installed (which has been installed for nearly two weeks with no sign of conflict). That will be the next course of action and we'll run Tech Tools. Any ideas or suggestions regarding this issue would be greatly appreciated. We all know that being down one machine is not a good thing - thanks in advance for any assistance.
PowerBook G4 17" 1.67 Ghz Mac OS X (10.4.5) Might Mouse, 1.5 GB RAM, 100 GB HD
PowerMac G4 Mac OS X (10.4) 20" Cinema Display - 2G 20GB iPod - much, much more

David,
I always had a pristine system: no kernel panics, no system hangs. Then, one day I started to have kernel panics and hang ups and when I tried to install XCode it failed, then I couldn't install iWork '06. At first I thought it was a problem with the disk until I decided to run Apple's hardware test. After all, it was just a problem with one of the 512MBs memory DIMMs. Removed the offending DIMM and everything went back to normal.
So, I think you should try the hardware test. To do this just start up from the original installation disk while pressing the option key and then choose Apple Hardware Test from the available startup disks.

Macbook display turns off when booting Snow Leopard DVD

I have mid-2009 Macbook Pro and I hate Mountain Lion. I want to do a clean install of Leopard using the DVD (grey) that came with my computer. I loaned it to a friend recently and he had no issues. But everytime i try to boot from the SL DVD (hold C at startup) it behaves normally, until about the time it would go into the DVD startup screen. At that point the display turns off (not the whole computer, just the display) as if it has gone to sleep. And I can't get it to turn on again. I've also tried booting and holding Option and choosing the DVD as the boot drive. No dice.
Awhile back I created a Lion install DVD. I can boot to it just fine. But i don't want Lion either. Any ideas why this is happening? Thanks!

Press control shift eject, then any key to toggle the display from sleep/wake.

Generation 2 VM boot from Media/DVD (not .iso)

So is it like that, that I cannot even boot Generation 2 from physical DVD media which is inserted in my Hyper-V host?

You can create ISO file using this PS script..
Sam Boutros, Senior Consultant, Software Logic, KOP, PA http://superwidgets.wordpress.com (Please take a moment to Vote as Helpful and/or Mark as Answer, where applicable) _________________________________________________________________________________
Powershell: Learn it before it's an emergency http://technet.microsoft.com/en-us/scriptcenter/powershell.aspx http://technet.microsoft.com/en-us/scriptcenter/dd793612.aspx

Spotlight reindexing drives when booting from Leopard to Tiger & vice versa

Hi,
I have two HDs, one with Leopard and the other with Tiger. Whenever I boot into the other HD I find that Spotlight re-indexes my two 750GB music & data drives which takes some time. Why is this? Do they use different versions of the index?
It's a bit of a pain as I have to boot into both OS's every day and cannot use Spotlight while the indexing is running and it also slows the system down. I do not want to turn indexing off as I need it during my work.
Any help/ideas?

dickie001x wrote:
Hi,
I have two HDs, one with Leopard and the other with Tiger. Whenever I boot into the other HD I find that Spotlight re-indexes my two 750GB music & data drives which takes some time. Why is this? Do they use different versions of the index?
yes, they do.
It's a bit of a pain as I have to boot into both OS's every day and cannot use Spotlight while the indexing is running and it also slows the system down. I do not want to turn indexing off as I need it during my work.
Any help/ideas?
I don't think there is any way around this. may I ask why you have to use both tiger and leopard?
you can try using some spotlight alternatives such as [EasyFind|http://www.versiontracker.com/dyn/moreinfo/macosx/11706] when you are using one of the two OS ( either tiger or leopard) and spotlight for the other os.

G5 Grey screen (Kernel Panic) when booting from CD

I know there are a lot of posts with people experiencing issues with the grey screen during boot. Most resolutions point to hardware but all state, including Apple's walk through, to boot from CD and run a validation on the hard drive.
My issue is completely different. I get the grey screen of death when booting from a CD/DVD only. I can boot into the OS just fine from the hard drive. But if I try to install another OS, or just boot from the CD/DVD, I get the grey screen.
What I've done to troubleshoot:
Reduced RAM to original sticks
Removed hard drive
Replaced DVD drive
Tried multiple versions of OS discs (10.2, 10.3, 10.4 and 10.4 server)
Reset the PRAM (Both via keyboard and Open Firmware)
Replaced the video card
Replaced the logic board
Replaced the Processor
Quite litterally the only thing original in this system is the power supply and the memory. However, I only get it when I'm booting from CD so the memory should not be the issue. I've even used a seperate power supply for the DVD drive to see if it was causing an issue.
Any suggestions? I'm looking at possibly replacing the power supply but I'm afraid it's going to give me the same issue.

Thats the thing, I've tried 10.2, 10.3, 10.4, and 10.4 server. (CD and DVD) All give me the grey screen. Well 10.2 and 10.3 give me a dark grey square in the middle where the apple should be but then the fans ramp up like it does when you get the grey screen of death.
I've also used two different drives.
It reads the disks fine with no issues. If I boot to the hard drive I can use the system like nothing is wrong. But if I want to boot from CD for any reason I cannot.
If I follow the logic it seems it is something to do with the CD/DVD drive. This is because it works fine when booted to hard drive. If it was the memory or PSU then I'd be getting the problem all of the time and not just when booting from CD/DVD.

Ethernet seems to work when booted from Leopard DVD--Not anytime else

Similar Messages

Maybe you are looking for