EVC and second-dot1q problem.
Hi all,
I'm trying to configure a interface with two dot1q tags but I can't do it.
I think thats is because my line card doesn't support it but I can't find any doc to confirm it.
I have a 7606-S chassis with two WS-SUP32-GE-3B, one WS-X6548-RJ-45 and one WS-X6516A-GBIC.
When I try to configure a subinterface in any line module with the command "encapsulation dot1Q X second-dot1q Y" the router doesn't accept second-dot1q part of the command,
Router(config-subif)#do sh run interface GigabitEthernet2/1.2
Building configuration...
Current configuration : 38 bytes
interface GigabitEthernet2/1.2
end
Router(config-subif)#interface GigabitEthernet2/1.2
Router(config-subif)#encapsulation dot1Q 3 ?
native Make this as native vlan
<cr>
I tried it in a interface of each module and always is the same output.
After, I have tried to use service instance but I can't set encasulation under service instance configuration part,
Router(config)#interface GigabitEthernet6/5
Router(config-if)#service instance 1 ethernet
Router(config-if-srv)#?
Ethernet EFP configuration commands:
default Set a command to its defaults
description Service instance specific description
ethernet ethernet
exit Exit from ETHER EFP configuration mode
ipv6 IPv6 interface subcommands
mac Commands for MAC Address-based features
no Negate a command or set its defaults
shutdown Take the Service Instance out of Service
snmp Modify SNMP service instance parameters
The easy way is upgrade hardware but is not a choice now...
Anybody know if it's possible do it with my hardware config?
Thanks in advance.
David.
Hello.
Yes, this kind of MPLS configuration is supported on SIP400, ES20/ES40 LC, but ES20/40 requires SUP720, so SIP400 is your only chose.
If you configure xconnect under service instance, you need SIP400 V2 SPA; if you configure under sub-interface -> just SIP400. In this case SIP400 is customer-facing LC.
Also you have an option to configure xconnect under interface VLAN -> SIP400 should be CORE-facing LC.
Similar Messages
-
I have an ipad mini 1st gen 64 gb (wifi only) and i have problem with some of my apps. These apps have lags when you play with them for a few seconds the apps are having lags are call of duty strike team, gta San Andreas and nfs most wanted.pleas help me
I'm going to guess videos buffer for a while also...
Two possibilities, one is you should close apps on the iPad, the other is your internet speed is not able to handle the demands of a high speed device.
To close apps: Double click home button, swipe up to close the apps.
To solve internet problem, contact your provider. Basic internet is not enough for video games and movies. Your router may be old and slow. -
I have an ipad3, iPhone3gs and iPhone5, my problem is my apple ID works all 3 devices but I need a second ID for the iPhone 5. How do I delete my ID and set up a new one for the iPhone5 but keeping my own apple ID for the iPad and iPhone 3GS.
http://support.apple.com/kb/he37
-
I purchased photoshop elements and i am having all the problems in the world installing it.... first the link in the emails were errors and secondly i have downloaded and installed multiple times and it says my serial number from the email i received is incorrect.... please help
Ok, since this forum is for Photoshop Standard and Photoshop Extended, we don't know much about Photoshop Elements. There is a Photoshop Elements forum and I'll link it for you since they best know how to field your questions.
Photoshop Elements
Good luck on it!
Gene -
been running version 4 for a week without problems. Today, downloaded MS live security update, and have had problems since. when I click on a favorite site, it takes 20 to 40 seconds before the page load's.'''bold text'''
http://portableapps.com/apps/internet/firefox_portable/localization#legacy36
-
I have continuous problems with my iPad Mini, and it is getting worse! Newstand application keep pausing or crashing, websites keep hanging first time in but then open fine the second time, and I have problems with applictions crashing. Has anyone experienced similar problems and any suggestions?
Has the device always behaved this way? Did this start as a result of an update to the iOS software? If the problem is that bad, you should probably restore the iOS software and then restore from a backup. If that fails, restore as new and rebuild the device. If that fails, it's time for a trip to an Apple Store to let them have a look at the iPad.
Use iTunes to restore your iOS device to factory settings -
HI pls i am having problem with my iphone4s since i updated to 8.2 i can't check balance of my account and secondly if somebody call me it is indicating number with out name pls what is the solution
When you have kernel panics, the pertinent information is in the panic report.
These instructions must be carried out as an administrator. If you have only one user account, you are the administrator.
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad and start typing the name.
In the Console window, select
DIAGNOSTIC AND USAGE INFORMATION ▹ System Diagnostic Reports
(not Diagnostic and Usage Messages) from the log list on the left. If you don't see that list, select
View ▹ Show Log List
from the menu bar.
There is a disclosure triangle to the left of the list item. If the triangle is pointing to the right, click it so that it points down. You'll see a list of reports. A panic report has a name that begins with "Kernel" and ends in ".panic". Select the most recent one. The contents of the report will appear on the right. Use copy and paste to post the entire contents—the text, not a screenshot.
If you don't see any reports listed, but you know there was a panic, you may have chosen Diagnostic and Usage Messages from the log list. Choose DIAGNOSTIC AND USAGE INFORMATION instead.
In the interest of privacy, I suggest that, before posting, you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header of the report, if it’s present (it may not be.)
Please don’t post other kinds of diagnostic report.
I know the report is long, maybe several hundred lines. Please post all of it anyway. -
logic 9.1.7 and mountain lion, problem, when i open any plug-in logic take up to 10 second to work orrectly, any click i make logic dont respond
https://discussions.apple.com/thread/4142085?tstart=0
-
i have an two ipod my first ipod is updated with4-3-3 version in itunes and second does not update in same itunes what had happen pls pls pls pls tell me
See:
iPhone, iPad, iPod touch: Device not recognized in iTunes for Mac OS X
If you have Snow Leopard do not forget the Additional Information paragraph. -
Email and big wifi problems.
Why does it take 6 minutes to send a photo attachment when my iphone 4 will do it in 30 to 40 seconds ?
Why will my email account be recognised and log on only half the time?
Why does the wifi keep dropping out?
Why does the speed and signal vary when I'm sitting two feet away from by wifi router?
All settings in my phone have been reset twice as per advice from vodaponeThanks very much, jjgraphics. I will grit my teeth and try India once more, as you suggest, and then get in touch with the moderators.
Karen. -
Calendar first and second alerts switch on their own
Hi, I've been having this problem for a while with my iPhone 4, wondering if anyone can help.
I've tried looking if there's already a thread for this issue, but couldn't find one -- maybe I'm just not using the correct keywords.
Every time I set my first and second alerts on my calendar appointment and saved them, they seem okay, but 2 minutes later when I go back to the same appointment, the first and second alerts switch on their own, e.g.: I set first alert to go on 2 hours before and second alert to go on 1 hour before the appointment. Save. When I return 2 minutes later, first alert turned to 1 hour before and second alert 2 hours before.
Which is silly, since who needs their second alert to be farther than their actual appointment? Even iphone knows this and cancels the second alert altogether. By the time I've been alerted, I only have an hour to get ready for my next appointment.
Anyone has encoutered this problem and has successfully solved them? I've tried setting my default time zone under setting to local, and even turning off iCloud, to no success.
Any suggestion is greatly appreciated. Thanks.I have found what appears to be a resolution to this issue, when I add an event and I select the event time, the date time scroller opens up allowing me to select the time of the event.
The issue occurs when I leave this selector expanded and continue to set the event properties. When the time selector is still open and you select the alert times, it swaps the alerts every time. When you collapse the event time selectors before choosing the alert times, the alerts are not switched.
This bug appears to be an issue with the scrolling selector form item if there is more than one open it appears to error out.
If you don't know how to collapse the event time selector, once you have selected the time, click on the date/time that is in red text just above it and it will collapse the selector.
Hopefully this fixes the issue for others, and it is ridiculous that this has gone one for so long, not a good way to keep your customers Apple, my wife was so aggravated at this that she was about to cancel her iPhone. -
How to get the first and second quarter from CRT
Dear Freinds,
I have one scenario , the Functional SPEC says Read the payroll results and from the CRT get all the 4 quaters
for the wage type /5UH and sum them and then pass on the to field in the main strucutre.
Iam using the FM HR_GET_PAYROLL_RESULTS
CALL FUNCTION 'HR_GET_PAYROLL_RESULTS'
EXPORTING
pernr = fp_v_pernr
permo = fp_v_permo
pabrj = fp_v_pabrj
pabrp = fp_v_pabrp
actual = 'A'
TABLES
result_tab = i_payresult
EXCEPTIONS
no_results = 1
error_in_currency_conversion = 2
t500l_entry_not_found = 3
period_mismatch_error = 4
t549q_entry_not_found = 5
internal_error = 6
wrong_structure_of_result_tab = 7
OTHERS = 8.
Iam collecting all the Actual Result (current result) values
on the selection screen iam passing for month april (04 2008)
so this falls in the second quater .
the internal table i_payresult is picking up only the second quater (01-04-2008 to 30/04/2008 ) ,but since on the selection screen iam pasing as other period (04 2008) the internal table i_payresult returing from the FM (HR_GET_PAYROLL_RESULTS) only picks the second quater,
could any one let meknow how i can pick up the first quarter as well and add the first and second quater to mee the requirement .
Please help me in this regard
Thanks & regards
maduriHi Manoj,
Thank you for giving me idea for going further regarding this problem , so my final question for this is
as per FS they said they are going to enter the payroll
area and the other selection as 04 2008
In order to achieve the first quarter , because 04 2008 means they are going to enter for the second quarter , the payroll results will come only for second quarter and not for the first quater , if they want to sum all the two quarters then they shouldnt pass on the selection screen the dates as 04 2008, instead they has to pas
01 01 2008 to 30 06 2008 , as there is no point in they passing as 04 2008 as we are going to consider from 01 2008 to 062008 . Please correst me if am correct regarding the dates passing on teh selection screen
or if the user enters on theslection screen still enter 04 2008 and will be able to acheive the first quarter ??
Please answer me this point before i can change the logic of the code and tell to my FO regarding this point.
thanks & regards
Madhuri -
GPIB and RS232 communication problems
I've been having several "interesting" problems with GPIB and RS232 communications in LabVIEW VIs. Some I'll mention at the end for curiosity, but right now I'm facing a rather big problem. I'm essentially self-taught at doing LabVIEW (using 8.5.1 right now), but by now I've had a lot of experience as their either has not been any drivers or pre-made VIs for the instruments I've needed or I've not been able to get the available drivers to work and had to write my own anyway (such as with the HP 3458A), but nothing seems to be working right now. I'm not at work, but we typically find forum sites blocked anyway (I can't even download the NI drivers at work since they house them on a ftp server, go figures) so I can't give the VI itself (it wouldn't be easy to get approval even if I could) so the best I can do right now is in words describe everything I've tried. I will be happy to post follow-ups of specific details if I can if they would be helpful.
I've been working on a routine to read data from an MKS 670 Signal Conditioner/Display with a MKS 274 Multiplexer with 3 connected MKS 690A Baratrons. Previously I've worked on programs using other older displays and the analog outputs which were being read by a DAQ card, but for a new project it was decided to try and just read the data directly. I first worked with a unit with just an RS232 Serial Port which I managed to get to work, but had so much problems with garbage readings and having to add checks and re-reads that by the end no matter what delays I added between each reading and how simplified the command routine down to just 2 sequences and the read that it took at least 10 seconds to get 1 reading from each channel.
Figuring maybe it was a limitation of the serial communications for these instruments I tried to re-work it for a unit with a GPIB port with which I'm actually much more familiar. The problem is that I cannot get anything at all from the unit through GPIB. Everything even the bare-bones built-in GPIB CLR function times out with no response from the instrument no matter how long I set the timeout limit and it also freezes the entire GPIB bus as well. It isn't a waiting issue as it freezes on the very first command. The GPIB initialization function seems to work (I typically find this to be unnecessary), but the instrument itself doesn't even respond with a status code. I've also tried just the basic GPIB write functions with even just passing the <cr> and <lf> characters as well. In Measurement and Automation Explorer most of the time the instrument won't even appear when doing search for instruments and when it does it shows as not responding to the *IDN? command (yes I've messed with the EOI, EOS, etc settings and I've even changed the GPIB address even though when it gets this far it confirms that I have the correct address) and even tried manually doing the *IDN?, *RST, and *CLR commands even with <cr> and <lf> characters which the manual for these units clearly states are compatible commands and NI SPY and everything show no response at all. I've tried 2 different GPIB units, 3 different computers including several that are not online and haven't been updated for a while, and using older LabVIEW versions, extensive re-booting and resetting of computers and devices and still nothing. I'm using an NI GPIB-USB-HS GPIB to USB adaptor which I've used extensively on other systems and even re-connected to those systems and everything worked fine. When I hooked up equipment that I knew was working, it would either freeze the entire GPIB bus until well past whatever timeout setting I set at which point all the instruments would appear, but none responding to *IDN? queries or nothing would appear at all, or if I manually turned it off when frozen the other instruments would work and most even respond to the *IDN? queries. The same goes for both of the GPIB instruments of this type that I tried and again for different versions of LabVIEW, difference computers (all Windows XP though), and every GPIB configuration setting I can find to mess with in every combination.
Any thoughts or suggestions would be greatly appreciated. I've had all sorts of weird problems with equipment and LabVIEW (you've got to love undocumented design features) that have frustrated me before, but I've never had an instrument never respond at all especially a GPIB one. Getting garbage yes, no response at all, no.
The side side issues I'm just mentioning as they may be related, but I'm really interested in the above as I have working solutions for these:
One I've had is with a Hart Scientific (prior to being bought by Fluke) 1560 Black Stack that would continually stop responding to GPIB commands when on a continual read function taking readings just every 4 seconds with 250ms between each GPIB read or write command but for up to hours in total and the times it stops responding are random as far as I can tell. I even started sending the *RST command before and after every read or write command and still it freezes. The only thing is to manually turn it off and then back on or manually go through the menus and manually trigger the GPIB reset routine at which point it immediately starts responding. However, when I got sick of having to babysit it and just decided to try the RS232 serial port (as that is all it has without the extended communications module) it works fine no problem and I can even get readings slightly faster from it. Using a Hart Scientific 1529 Chub-e it could give me data on all 4 channels every second without problems. I just find it a bit odd.
When I couldn't get any of the HP 3458A driver packs to work to even give a single measurement reading and just made my own using basic GPIB read/write commands using the programming manual I still have a few interesting problems in randomly when reading off the full possible 256 bytes on the bus and clearing the bus I often find garbage partial readings on the bus every now and then. I've added a few routines to do some basic checks, but it is annoying. What is really weird is when just doing basic DC Voltage reads the "-" sign will randomly be dropped from some readings (started as about 1 out of every 5, down now to about 1 out of every 10). Fortunately I'm taking several readings and averaging and taking the standard deviation with limits on the deviations and basically added a routine to say if there is even 1 negative number take the absolute value of all then make all negative, but again I find it weird.
Thanks.
-Leif
Leif King
Metrology Engineer
Oak Ridge Metrology CenterGreetings Leif,
I understand you have completed extensive troubleshooting techniques to pin-point the problem with the GPIB communication. To begin, I want to ask you a few questions to help me understand your set-up and the issue at hand.
1) Is the NI GPIB-USB-HS cable the one which cannot communicate with your instrument?
2) When using the GPIB-USB-HS, does the GPIB interface show up in MAX?
3) If yes, does the instrument appear in MAX after scanning for instruments (from what I understand in your issue, it does so in an intermittent manner..)?
4) What driver version of VISA do you have installed in your computer?
5) Are you able to communicate to the same instrument using another GPIB cable?
Thank you for trying out some of these steps again, but we want to make sure we rule out other aspects in the systems which might be affecting the GPIB communication.
As for your other issues, please post seperate threads for each so we can help you accordingly. Thanks!
Sincerely,
Aldo
Aldo A
Applications Engineer
National Instruments -
Row 6 in this spreadsheet is the result of Row 2/Row 3 as evidenced by the formula listed while Cell Y6 selected. How can I make the values in this row appear as durations of minutes and seconds rather than 3-digit decimals? For example, rather than appearing as 9.84 I would like the value of Cell Y6 to appear as 9:50 or 9min 50sec. (obviously .84x60seconds 50 seconds). I tried changing the cell formats from "number" to "duration," but no change is made. Using the "duration" format does however work if I am manually entering the decimal value into the cell rather than allowing it to result from another caluclation within the spreadsheet. Is there a solution to this within Numbers '09? You can see why I would want the "pace" displayed in minutes and seconds. Thanks in advance!
RyanHi Ryan,
You wrote:
"The problem is that my "Distance" is a row of automatically generated values resulting from ((Row1/60)*Row 6). Changing the format of Row 1 to minutes causes row two to be expressed as a duration, which obviously it shouldn't because it is a distance. The spreadsheet has to be designed so that all I have to manually input on each entry are Row 1 Values (Time) and Row 6 Values (Average Pace). The rest of the cells must be automatically poulated as a result of formulas."
I'm assuming that where you say "Row 1" in this you mean "Row 2", which is labeled "Time" in the example in the OP.
In the original post, you presented a formula from cell Y6. Replacing the Header labels in that formula's cell reference with the Addresses of the referenced cells, the formula was:
Y6: =Y2/Y3
In this post, you are saying that Y6 contains entered data: "...all I have to manually input on each entry are Row 1 Values (Time) and Row 6 Values (Average Pace).
Which is correct?
Regards,
Barry -
Field with time in minutes and seconds
Dear community,
first of all, I am using Apex 3.1 on Oracle 10g, if this is necessary to know (yes I know, an old version, but given by the company I'm working for). After I've developed a few applications in Apex, thank to the forum and all the answers inside, I came to a problem that I could not solve:
I want to have a normal text field, where the user can enter a duration of an event (e.g. "3:45" or "2:30"). That duration will allways be in the format "MM:SS". No hours, no milliseconds... But how can I save the given values in the database, so in which format? A varchar would be a possibility, but I want to build a report later on, where there is a sum of the times. And how to get a sum of varchar?! But how to make it clear to Apex and Oracle DB that the users gives in a time and not a varchar? The only thing oracle offers is a date field, but I want to save a time and not a date!
Does anybody has a clue for me, cause it seems to me, that possibly I just don't know what I'm searching for, cause people must have had this problem before!?
THanks for your help!
Regards
hogeBut how to make it clear to Apex and Oracle DB that the users gives in a time and not a varchar? The only thing oracle offers is a date field, but I want to save a time and not a date!All APEX items are character strings, so implicit or explicit conversion is required when the values are stored in database columns. For the recommended <tt>INTERVAL DAY TO SECOND</tt> columns, use <tt>TO_DSINTERVAL</tt> to perform the conversion.
Use <tt>EXTRACT</tt> to get the minute and second values from the <tt>INTERVAL</tt> going in the other direction.
but I want to build a report later on, where there is a sum of the times.A user-defined aggregate function can be created to sum <tt>INTERVAL DAY TO SECOND</tt> values: here's an example.
APEX's lack of built-in support for summaries on <tt>INTERVAL</tt> types can be worked round by including the sum in the report query using a </tt>UNION</tt>:
SQL> with test_data as (
2 select
3 rownum n
4 , numtodsinterval(ceil(dbms_random.value(0, 3600)), 'SECOND') t
5 from
6 dual
7 connect
8 by rownum <= 10)
9 select
10 n
11 , t
12 , to_char(extract(minute from t))
13 || ':'
14 || to_char(extract(second from t), 'fm00') t1
15 from
16 test_data
17 union all
18 select
19 null
20 , sum_dsinterval(t)
21 , to_char(extract(hour from sum_dsinterval(t)))
22 || ':'
23 || to_char(extract(minute from sum_dsinterval(t)), 'fm00')
24 || ':'
25 || to_char(extract(second from sum_dsinterval(t)), 'fm00')
26 from
27 test_data
28 order by
29 1 nulls last
30 /
N T T1
1 +000000000 00:04:46.000000000 4:46
2 +000000000 00:07:05.000000000 7:05
3 +000000000 00:31:11.000000000 31:11
4 +000000000 00:53:16.000000000 53:16
5 +000000000 00:19:02.000000000 19:02
6 +000000000 00:57:12.000000000 57:12
7 +000000000 00:43:29.000000000 43:29
8 +000000000 00:03:11.000000000 3:11
9 +000000000 00:16:40.000000000 16:40
10 +000000000 00:20:49.000000000 20:49
+000000000 04:16:41.000000000 4:16:41A custom named column (row) report template with conditional templates can be used to layout and format such a report so that the summary row(s) are properly handled.
Maybe you are looking for
-
HT1660 How do I run itunes from external Hard drive?
How do I run itunes from external hard drive. I only have ssd on PC and media is too large to fit
-
If I have to validate Outlook on PC or Mac - I have no problem - the random numbers and letters display fine - but if I am requested to validate outlook before sending a mail when using my iPad, the operation fails as the test numbers and letters are
-
Apps do not respond when waking from sleep mode in Mountain Lion
updated to the new OS a few weeks ago (no more than 14days) - since the upgrade, everytime the Mac awakens from the sleep mode, nothing responds. If you select the app the app will just bop up and down. If you try to clear trash, the message window
-
Purchase Order Document Type Defaulting in ME58 while converitn PR to PO
Dear All While converting Purcahse Requesition to Purchase Order in ME58, System defaults one Purchase order document type . Ofcourse we can overwrite that But would like to know how this defaulting can be controlled in SAP Regards Shyam
-
when I run AIBU, it reports the error: Acquisition value negative in depreciation area 01, but I checked AUC, there is positive net book value 1000, My AUC has two transactions , in Nov, it settled from project system, P&L account is credited with 3