Every time I enable the OnBoard USB, in bios, the memory check takes ages.

yup. Every time I change the OnBoard USB to enabled in BIOS, the startup memory check takes for ages (approximately 5 minutes or so...)(the check jamms for a few numbers before it's finished, it jamms on numbers 104857 and after a little while it goes to the end 1048576 and continues the startup process) and this is really starting to annoy me 'cause I have to use a non-optical mouse and non-wireless keyboard because of that stupid bug or what-so-ever. Is the only choice BIOS update?
Edit1: the motherboard is MSI KT400, so it's VIA based.

Please run  Memtest86 after disabling usb.
And btw a complete list of your hardware including the specs (amps!) of your psu would be helpfull.
Edit: You've already opend another thread about same topic so I close this one.
No double threads please.

Similar Messages

  • Every time I connect the usb on the computer, lightroom opens. I want to disable it. How do I?

    every time I connect the usb on the computer, lightroom opens. I want to disable it because, , often, there is nothing to edit photos.

    Autostart/autoplay options are defined in your operating system. Richt-click the drive letter/ volume name and change them accordingly. On Windows there's alsop a system control panel for that.
    Mylenium

  • Why does my router disconnect every time I sleep the computer? Why did this only start to happen recently?

    Why does my router disconnect every time I sleep the computer? Why did this only start to happen recently?

    Actually it does with Ethernet too: http://support.apple.com/kb/HT2412?viewlocale=en_US&locale=en_US
    What happens when the Mac goes to sleep (not just into idle mode or display sleep)?
    On all Macs:
    The microprocessor goes into a low-power mode
    Video output is turned off, and a connected display may turn off or enter its own idle state
    Apple-supplied hard disks spin down; third-party hard disks may spin down
    On portable Macs:
    The Ethernet port turns off, if applicable (see note below)
    Expansion card slots turn off
    The built-in modem, if present, turns off (see note below)
    An AirPort card, if present, turns off (see note below)
    The USB ports only responds to the power key on an external keyboard (see below)
    The optical media drive, if present, spins down
    Audio input and output turns off
    Keyboard illumination, if a feature of your portable computer, turns off
    But see the note about selecting, "Wake For Network Access" in Energy Saver preferences.
    Note: Portable computers have no network connectivity when in sleep mode, but can wake if the Energy Saver option "Wake for network access" is enabled. If you wish to use file sharing or don't want to interrupt your Internet connection, you should not manually put the computer to sleep, and you should drag the "Computer sleep" slider to Never.

  • Trying to use a new, larger external hard drive for my Time Machine backup.  However, every time I start the backup, it gets started then fails.  And, I can't delete the few files that did save on the external.  Sort of a catch 22.  Any ideas?

    Trying to use a new, larger external hard drive for my Time Machine backup.  However, every time I start the backup, it gets started then fails.  And, I can't delete the few files that did save on the external.  Sort of a catch 22.  Any ideas?

    Is it a USB hard drive?  USB hard drives have the problem of not giving full speed if they are hooked up on the same bus as keyboards and mice.  Double check your profiler to make sure that is not a problem.  If it is Firewire, make sure there aren't other firewire devices in use at the same time.  I recommend not only keeping a Time Machine backup, but also a clone, and if you do use Time Machine, to make sure the Time Machine drive or partition is at least twice the size of the original drive.

  • How do I change the volume for a single midi instrument in GarageBand 10? Every time I move the volume, it moves back!

    How do I change the volume for a single midi instrument in GarageBand 10? Every time I move the volume, it moves back!

    Every time I move the volume, it moves back!
    Check, if you have a volume automation set on the software instrument track.
    If the track volume automation curve is enabled, the volume slider for the track will move with the automation curve.
    Click the automation curves disclosure triangle in the track header and disable the volume automation.

  • HT1338 My MacBook Air is very slow. Every time I click the mouse, the spinning wheel appears and remains for up to 30 seconds. Can you help me?

    My MacBook Air is very slow. Every time I click the mouse, the spinning wheel appears and remains for up to 30 seconds before the screen changes. This has been happening the past 24 hours. Any ideas?

    First, back up all data immediately, as your boot drive may be failing.
    If you have more than ten or so files or folders on your Desktop, move them, temporarily at least, somewhere else in your home folder.
    If iCloud is enabled, disable it.
    Disconnect all wired peripherals except keyboard, mouse, and monitor, if applicable. Launch the usual set of applications you use when you notice the problem.
    Step 1
    Launch the Activity Monitor application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
    ☞ If you’re running Mac OS X 10.7 or later, open LaunchPad. Click Utilities, then Activity Monitor in the page that opens.
    Select the CPU tab of the Activity Monitor window.
    Select All Processes from the menu in the toolbar, if not already selected.
    Click the heading of the % CPU column in the process table to sort the entries by CPU usage. You may have to click it twice to get the highest value at the top. What is it, and what is the process? Also post the values for % User, % System, and % Idle at the bottom of the window.
    Select the System Memory tab. What values are shown in the bottom part of the window for Page outs and Swap used?
    Step 2
    You must be logged in as an administrator to carry out this step.
    Launch the Console application in the same way as above. Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left.
    Post the 50 or so most recent messages in the log — the text, please, not a screenshot.
    Important: Some personal information, such as your name, may appear in the log. Edit it out before posting.

  • Every time I enable 3G I get 'No Service', why is it doing this?

    Every time I enable 3G I get 'No Service', why is it doing this?,
    But then sometimes it will get service but i cant use my 3G, only Edge works
    Any Help is appreciated
    Thanks in Advance

    The most likely reason is that your carrier is not providing 3G service in the area where you're located. Contact your carrier for coverage details.

  • PS3 Gamepad Support in Mavericks - do I need the cable every time to avoid the flashing lights?

    I now have an early 2011 Macbook Pro, 17".    I kind of wanted to play a few games without resorting to the keypad, and had heard that PS3 controllers worked out of the box with Mavericks. 
    I followed the instructions found online in various places - basically all the same - plug in the USB cable, it shows up in the bluetooth list - hold the PS button in the center for a couple of seconds and disconnect it, and it connects to the mac.  Sometimes, for whatever reason it asks for a PIN, sometimes not.  Either way, it works perfectly. 
    The thing that's throwing me is what to do when I'm done - if I turn off bluetooth, put my computer to sleep, or turn off the controller by holding down the PS button, reconnecting later on is a bit off from what I'd expect. 
    I make sure bluetooth is on, and press the PS button in the center of the controller, and the lights in the back start blinking fast (about twice as fast as when charging or during the normal connection process).  The controller shows connected in the bluetooth menu, and appears to work fine (although I haven't tried it out very long like this) but the lights continue to blink quickly the whole time!  The only way I can manage to get the blinking to stop is to disconnect the bluetooth connection, and reconnect via the "connect USB, press button, disconnect USB" method.
    It's not a deal breaker for me, but I'd really like to just be able to grab the controller and go without digging up a cable every time, and was curious if any other Mavericks users had this problem or a workaround?  Or do I really need to do the wired setup every time I pair the controller to my mac?   I suppose I could live with the blinking lights, but darn is it annoying! 
    I've tried searching online, and a lot of the info I stumble across either mentions older verisons of Mac OS X with a different bluetooth menu and slightly different things than I'm seeing, or simply don't mention reconnecting after pairing the device.  (And is there a difference between "paired" and "connected" in this instance - it shows as "paired" after the time it asked for a PIN, but only "connected" normally. 
    The controller is a legit, first-party Sony controller, (as far as I can tell) that was marked "official playstation accessory" (or something along those lines) on the packaging and bought new from a local Gamestop.   I don't think they'd sell me one of the knock-off controllers as a legit one at a brick and mortar. 

    Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. You may have to leave the machine there for several days.
    Back up all data on the internal drive(s) before you hand over your computer to anyone. There are ways to back up a computer that isn't fully functional—ask if you need guidance.
    If privacy is a concern, erase the data partition(s) with the option to write zeros* (do this only if you have at least two complete, independent backups, and you know how to restore to an empty drive from any of them.) Don’t erase the recovery partition, if present.
    Keeping your confidential data secure during hardware repair
    Apple also recommends that you deauthorize a device in the iTunes Store before having it serviced.
    *An SSD doesn't need to be zeroed.

  • Every time I type the letter t in an email, Firefox takes me to a blank search page

    Every time I type the letter t in an email, Firefox takes me to a blank search page
    == This happened ==
    Every time Firefox opened
    == Every time I type the letter t

    Hello Noleska.
    It's possible that you are having a problem with some Firefox add-on that is hindering your Firefox's normal behavior. Have you tried disabling all add-ons (just to check), to see if Firefox goes back to normal?
    Whenever you have a problem with Firefox, whatever it is, you should make sure it's not caused by one (or more than one) of your installed add-ons, be it an extension, a theme or a plugin. To do that easily and cleanly, run Firefox in [http://support.mozilla.com/en-US/kb/Safe+Mode safe mode] (don't forget to select ''Disable all add-ons'' when you start safe mode). If the problem disappears, you know it's from an add-on. Disable them all in normal mode, and enable them one at a time until you find the source of the problem. See [http://support.mozilla.com/en-US/kb/Troubleshooting+extensions+and+themes this article] for information about troubleshooting extensions and theme and [https://support.mozilla.com/en-US/kb/Troubleshooting+plugins this one] for plugins.
    If you need support for one of your add-ons, you'll have to contact its author.

  • Itunes 11 welcome screen every time I open the program.

    Yeah,
    itunes 11 opens to welcome screen every time I open the programme.
    OS Win8
    very annoying
    help?

    This is what worked for me!!!!!
    Close iTunes.
    With Windows Explorer go to View in the top menu and allow Hidden Files.
    Navigate to:
    C:\Users\[which ever user is you]\Appdata\Local\Apple Computer\iTunes
    Delete all files in this directory.
    Start iTunes and see the Welcome Screen for hopefully the last time!
    I am not an expert.  This was a stab in the dark based on the Mac ByHosts solution and it just happened to work for me.  Give it a try and let me know if it works.
    Good Luck!

  • Why does the Welcome to firefox tab open with my google tab every time I open the browser? And why can't the browser hold any add-ons I downloaded? I loose then when I close the browser, even tool bars have to be reinstalled every time I open the browser

    Every time I open the browser the Welcome to Firefox tab is the first tab, then a second tab opens and thats my google, then a 3rd tab opens for me to reinstall my toolbar. This has been happening for a good year. Updates have not fixed it. Others have this problem. I did a search for an answer, the question is out there but no answer. Now if I go into add ons and add a background Theme or an extension it all is gone when I exit the browser. When I open the browser again I get all 3 tabs and have to install my toolbar again. I DO NOT want to reinstall as I will loose all my saved data, passwords, bookmarks, everything! I have had this computer for a year, Windows Vista x64 bit. Its not the computer, it's the browser. If you have specific questions e-mail me and I will be more then happy to help

    See this article for some suggestions: [[Firefox has just updated tab shows each time you start Firefox]]
    See also http://kb.mozillazine.org/Preferences_not_saved and Preferences are not saved

  • I am trying to install a program on my Mac Book Pro Retina from a Apple SuperDrive. Every time I run the installer, it says I do not have enough memory to install. However, I definitely have enough memory (186.74 GB). Any ideas why?

    I am trying to install a program on my Mac Book Pro Retina from a Apple SuperDrive. Every time I run the installer, it says I do not have enough memory to install. However, I definitely have enough memory (186.74 GB). The program takes only 550 MB. Any ideas why?

    Thanks for the clarification on the terms. I consider myself proficent at my computer, but not exactly in its inner-workings! I have 8 GB of memory installed.
    I am still confused as to why I do not have any space for the program. This is the exact error message I get: "There is not enough free space on Macintosh HD disk. The Print Shop 2 application requires about 550 MB to be installed. Free some disk space and try again."
    Thank you again for your help.

  • I'm trying to download office 365 small business package, and every time I try the website it says there is a runtime service error in the '/' application. Is this my mac or is it the website, and how can I fix it?

    I'm trying to download office 365 small business package, and every time I try the website it says there is a runtime service error in the '/' application. Is this my mac or is it the website, and how can I fix it?

    If a phone is sold from one friend to another and wants to use it on a different carrier the friend can contact the carrier it was sold by to request it unlocked.  I know AT&T, Verizon, and Sprint will give you the steps to unlock it as long as the original contract it was bought under has been completed.  eBay/Craigslist is really not the best place to try to get "unlocked phones" from, if it turns out the phone isn't unlocked then I'm really sorry you got stuck with that one and as stevejobsfan said above I would report them immediately and see if you can recover your money.  I sell phones for a living and this happens a lot

  • I am trying to use the trial creative cloud software on a PC windows 8.1 - I've downloaded and removed Photoshop CC 2014 two times - every time I open the file it says there is a problem and it shuts down and closes. I can open indesign and maybe other ap

    I am trying to use the trial creative cloud software on a PC windows 8.1 - I've downloaded and removed Photoshop CC 2014 two times - every time I open the file it says there is a problem and it shuts down and closes. I can open indesign and maybe other apps but photoshop no. Any ideas?

    I don't think I can access the crash report? Excuse the ignorant questions I'm about to make am a relative tech novice.
    Soo - as mentioned every time I open photoshop it crashes - it just says there's an error and the program will shut down and if there's a solution windows will notify me. Then nothing...
    I've tried to look in photoshop files for the detailed crash report & the system event viewer but cannot find a file with those names. I've also looked in the windows files for files with those names but cannot find them either - so I don't know where to look.
    Any guidance would be great.

  • I have set up a Netgear dual band modem which works well with the iPhone and an older MacBook, but with this brand new MacBook it asks for a password every time I reopen the computer and open safari. Is it Lion?

    I have set up a Netgear dual band modem which works well with the iPhone and an older MacBook, but with this brand new MacBook it asks for a password every time I reopen the computer and open safari. As you can imagine this is very annoying. It says I am not connected to the internet and offers me a choice of nearby networks including mine and then asks for a password when I select it. Why does it do this with our new MacBooks (also with my son's brand new one) and not with the iPhone, iPad and older MacBook? They happily automatically connect to our network after entering the password just the once.

    Sig, I appreciate you trying to be helpful. I have no idea what issues you were having or what issue exactly pgrounds has been having. Your assumption that everyone's set up is the same as yours is false however. There are many many documented WiFi issues that are a result of Lion installs. Many have been solved by 10.7.1 and 10.7.2. Others have been solved by a large variety of work arounds. Others have not had their issues solved yet.
    I am one of those. I have an IT background, and I spent the better of five hours digging up workarounds and attempting all of them. For the benefit oh anyone who is having similar issues, I have posted links to all of those workarounds here. None of them worked in my case, but hopefully they will help pgrounds or others.
    So, once again, if you have a new idea, I'd love to here it. But if it has already been posted in one of these links, it's not helpful, let it go.
    http://osxdaily.com/2011/07/22/wifi-dropping-in-os-x-lion-fixes/
    http://osxdaily.com/2011/11/06/lion-wi-fi-problems-solution-mac/
    http://blog.chron.com/techblog/2011/09/want-to-really-repair-permissions-on-your -mac-try-this/

Maybe you are looking for