Excessive HD usage after archive and install.

After I did an archive and install, the HD is usage is up to 70 something from 60 something gigs. I was warned that 15+ gigs would be needed to install OSX, but I was under the impression that it was temporary and would be deleted after it was done. Can I go delete something manually?

No, nothing is deleted automatically. The Previous System Folder conyains your old system until you delete it.

Similar Messages

Finder not responding after Archive and install

I recently encountered my first problem ever with my mac(new in '05) This is the first mac I have owned; I have worked on G3's and G4's in the past. After reading through many message boards and support pages I don't believe my problem to be similar but different to previous posts.
My problem started off with an OS problem that I was able to diagnose in the "help" book I purchased when Leopard came out. It said I should Archive and Install to remedy the problem and keep my files. I ran the archive the install (it gave me no options to preserve user or network settings). After Archive and install my computer started up alright, but I got the permanent beachball and the finder does not work. it is constantly non responsive. I can relaunch finder, but after it restarts it goes non responsive immediately once again. So I can't actually access my "previous system" folder to move anything over. I checked my dock items and finder, they opened, but my itunes asked for an update. I list of update items came up; I did the non-restart items first. they updated fine, (my itunes old itunes playlists are viewable but not playable now) then I did the items that required a restart. That is when I found out that I could not shut down or restart my computer with std. procedures.
Currently I can only access my spotlight or apple pull down menu if I am in a functioning dock program (safari or itunes, quicktime. etc.) after reading some more support pages it looked like the common thing to do was check permissions and verify disk. I did, I repaired two permissions and the disk was OK. I did look at the HD files, they were as I remembered, but unaccessible (greyed out) and the "previous system" folder was present. +It didn't look like I would expect. The HD looked same as it used to just with a previous system folder.+ After checking the permissions and verified the disk I tried a hard restart. It came back the same as before, unresponsive finder and only the few dock items worked along with spotlight. I checked permissions and disk verify again and everything was OK.
Sorry to be long winded I am trying to be thorough...In short, My finder does not work after doing an Archive and Install to fix my original problem (which has been fixed)...the remedy for an unresponsive finder is to do an archive and install. Is another archive and install really going to fix my problem? Can I archive and install OSX 10.4 and work my way back up to 10.5.6?
Secondly is there a way to restart my computer without doing another hard restart?

It won't let me add a new account. I am locked out and when I try to unlock it gives me the beachball and becomes non responsive after it tries to authenticate.
I looked at the log file, I am not sure what exactly to look for. I am no programer. I see an awful lot of negative wording. I see some errors like "error (-4956) locating menu extra but they are mostly under system preferences...I see some stuff in the loginwindow that says is not a full path... Otherwise, the only reference I see to the finder is when I have force quit the finder.
2/8/09 8:59:55 PM com.apple.launchd[114] ([0x0-0x4d04d].com.apple.finder[304]) Exited: Terminated
2/8/09 11:10:17 PM com.apple.launchd[114] ([0x0-0x57057].com.apple.finder[321]) Exited: Terminated

Where is mail stored after archive and install?

Hello All,
I need to know where my old mails are stored after archive and install. To give a bit of background... This is a work computer. Its a MacMini which came with 10.4 installed. Before I joined the company boss upgraded to Leopard and thats what I have been using all this time. Recently it blue screened and I had to do an archive and install after trying various other options.
I only had the original install discs with 10.4 in them and not the Leopard discs. Since I needed to my computer up and running, I used those discs and did an archive and install.
I have all my old documents, etc but I couldn't open mail from the previous systems folder because its a different OS.
Is it possible to retrieve my old emails without having to install Leopard again?
Any help is appreciated.

When I started the computer up, instead of the login page with the account names coming up, there was just a blue screen. There are lots of articles that gave suggestions to try but nothing worked so I had to archive and install.

Cd inserted but unrecognized after "archive and install"

After "archive and install" OS X.2 and clicking on "save settings", everything works fine, except sound cds are not recognized when inserted. iTunes works fine with the original files on hard disk, but doesnt see the cd (it did before).
I repaired permissions. I deleted the "previous systems" folder. still nothing.
I did notice that the "previous systems" folder has an "audio" file in it but the current "system" folder doesnt. I tried copying this audio file into the current "system" folder but I get the notice that it cant be changed.
I need to hear cds on this computer. Any ideas?
(It isnt a speaker problem as the itunes files play fine).
John in Vancouver

Hi John in Vancouver! And Welcome To
Discussions!
Open System Preferences > CDs & DVDs.
Adjust the appropriate setting there, and see if it
helps.
Good Luck!
ali b
Thanks, ali, but I did that early on. Didnt put it in the post. On insertion of a CD I have it set to open iTUnes.
I found a further problem which is that the midi set-up no longer locates my external keyboard. I will check the discussions under audio for this one, however. (I did check about the CD problem in the audio discussion but nothing there.)
John

Recover mail after archive and install

Hey there good mac people,
I recently archived and installed on my ibook g4. It was successful, my problem is that I forgot to backup all the mail I had in my osx mail app.
The previous system folder (library<mail<mail accounts<com.mac.mailaccounts<English.lproj< file, but I don't know if this will help restore or not?
Some of the mail is still on the server, but it is set to delete from the server once a week, and thus only a weeks worth at best is still on the server.
Does anybody have any suggestions?
In the future, what's the best way to back up mail?

Hello art-is-work.
I don't understand your problem. Archive and Install should have preserved all your data, unless you told it to do otherwise. Did you?
Mail stores most preferences and all account settings in ~/Library/Preferences/com.apple.mail.plist. Everything else, including all your messages and mailboxes, is stored within the ~/Library/Mail/ folder.
If the problem is that you told the installer to not Preserve Users and Network Settings, then Archive and Install should still have saved a copy of your entire home folder in /Previous Systems/Previous System N/Users/, where N is a number. The old Mail folder and preferences file should be there. You can just copy them to the appropriate location of your current home folder, or follow the somewhat convoluted procedure described in the following article to safely restore them:
How to get files from a previous home directory after Archive and Install (Mac OS X)
Note: For those not familiarized with the ~/ notation, it refers to the user's home folder.

I need help to recover/relink mail after archive and install

I am helping my friend fix her 15" G4 PowerBook after memory failures caused many crashes. There was no recovering short of a reinstall via "archive and install". All that worked great, but now Mail doesn't recognize the accounts, mailboxes, signatures, etc. that are still located in the user/library/mail folder.
What's up with that? I can't figure out how to relink Mail to this stuff.
Here's more detail:
1) After lots of prior debugging (Disk Utility, Disk Warrior, Apple Hardware Test, single-user commands per Apple tech notes), I did the A&I to 10.3.4 from the original disks.
2) Per Dr. Smoke and The X Lab, I ran the 10.3.9 combo installer right away so that the "older" system would not get confused by the "newer" stuff in the Previous Systems folder.
3) I Launched Mail and it started anew, i.e. didn't recognize accounts and wanted to start over.
Thanks for any help.

The account settings are stored in HOME/Library/Preferences/com.apple.mail.plist. It looks like that file became corrupt -- maybe its permissions went awry (Disk Utility cannot fix that) and Mail just deleted the file to create a new one.
If your friend doesn't have a backup copy of that file, just set up the accounts from scratch all over again. If given the option to import existing mailboxes or something like that, don't. Just enter the account information and Mail will automagically rediscover the data in HOME/Library/Mail/ when done.
You'll also have to re-configure most settings in Mail > Preferences. For spam-related security reasons, the first thing you should do is go to Preferences > Viewing and disable Display remote images in HTML messages if it's enabled.

Recovery of lost printers after Archive and Install

Hi,
I just finished an Archive and Install of Leopard, and I discovered that one of the side-effects of doing this is that my printers are all gone. I sort of expected this, and I have a full system backup of the system I rebuilt, so if all else fails, I can boot off the backup, and print or take notes on the printer settings, and then go back to my active installation of Leopard and re-enter them all. But I'm wondering if there's an easier way. Would anyone know if all of the printer info might be contained in a few discrete sections of the "Previous System" folder that I could just drag into the current system folder to get all of my printers back? I do consulting work at a number of companies, so I have about ten printers that I routinely print to, so it's a bit of a bother to rebuild the list by hand.
Thanks,
Ken

Usually, when no additional printer software had been installed into the Mac
(assuming the printers are among the many supported printers already in it)
all you'd have to do in order to use one of those attached or available printers
would be to have them turned on and attached to the computer or the network
they'd normally be accessed through. Unless they require newer driver software.
At times, the choices of available printers would appear in the print setup in an
open application; at others, you may have to go into the setup utility to see if
the printers could be added to the list - pulling drivers from the installed OS X
and putting them into a position to be used, if compatible with the printers there.
The system's installer and updated files available to it include many drivers,
and these are not all turned on by default.
So, if there is no chance of the printers being recognized by the OS X version
you have (assuming archive & install and update) even after being given any
new drivers available through Software Update, you may have to seek out the
latest drivers from the printer manufacturers web site downloads pages.
There may be some other way to make the printers work through the OS; if
they otherwise should appear and be available. Some of the printer setups
& CUPS printing options or settings should be explored if they haven't been.
Although I don't have OS X 10.5.x running in my computers now, I have tried
it and decided to stay awhile longer in 10.4.11; some of the same kinds of
issues can occur, between these slightly different systems. You may be able
to re-use the printer drivers from the Previous System, unless their installer
had an instruction set to put various parts for the printer software in different
locations, in which case, the drag-n-drop may not be suitable to reinstall them.
Hopefully someone with more restore experience (short of manually reinstalling
drivers, if these are not already a part of the OSX and its 10.5 install/updates)
will contribute a bit more and direct you as per the specific demands of Leopard.
PS:
When you get your system back in order, you may wish to consider making a
full computer drive clone on an externally enclosed FireWire drive unit capable
of booting Mac OS X and running your PPC-based Mac (and also Intel-based)
so that unit may be something in the way of a FW400/800 + USB2.0 drive with
its own AC power adapter. OWC sells a mercury drive enclosure with HDD in it.
That may be a way to avoid doing Archive & Installs + updates; just restore from
a full drive clone and be on your way. And do other backups if needed, too.
Good luck & happy computing!
{ edited 2x }

Blank iTunes library after Archive and Install

My PowerBook G4 suffered a catastrophic crash and after advice from Apple support, the only way I could restart it was to perform an Archive and Install. Before this, I couldn't start the machine and therefore couldn't back anything up. Everything seems to be all right after the Archive and Install except that my iTunes library is completely blank, and the old library is not anywhere on the hard drive. All of the songs are still on my iPod - is there any way to get them back into the library? I don't want to connect the iPod and lose everything I have now.
Thanks!
PowerBook G4 867 Mhz Mac OS X (10.2.x)

From the Keyboard Shortcuts in the iTunes Help menu:
iPod shortcuts
Prevent iPod from automatically updating when you connect it to your computer
Command-Option as you connect the iPod to your computer (hold the keys down until the iPod appears in the iTunes Source list)
After that, use an application like Senuti or iPodRip (latest versions on versiontracker.com) to transfer the contents of your iPod to the computer.
Hope this helps.
M
17' iMac fp 800 MHz 768 MB RAM Mac OS X (10.4.6) Several ext. HD (backup and data)

Video podcasts won't play after archive and install

I'm one of the folks having capture issues with FCP 4.5 and OS X 10.4.9. So I decided to archive and install to 10.4.8. Now it seems I'm having all kinds of video problems, including downloading and playing video podcasts in iTunes (7.2). When I download a podcast, say "Tiki Bar TV", the file downloads, but in the podcast screen, I get an error message which reads,
"There is a problem adding the video to iTunes. The file might be corrupted, or a file type that iTunes cannot play." For the record, I have never run into anything like this before. And it's the same way with every video podcast.
I had some similar wonkiness going on with QuickTime, too. But after I installed a divx plug-in, and flip for mac, everything seems to be okay with the QT. iTunes is still a mystery. Any ideas on what my next step should be would be appreciated.
Thank you.
Ben
PowerMac G5 Dual 2.5Ghz Mac OS X (10.4.8) 3GB RAM, 500GB hard drive, ATI9800XT

There are files that are not brought along with Archive and Install.
Some are invisible and not accessible without enabling "root" access and even then you have to know exactly which files have to be moved from the 'previous System' folder.
Archive and Install never works with Apple's Pro apps.
If Niel's suggestion doesn't work you'll have to erase your hard drive and reinstall everything making sure you first backup important data to another hard drive.
(don't forget to save your mail and addresses)

Restoring after archive and install

after using 'archive and install', what is the proper procedure for restoring applications, plugins, etc?
1. manually copy?
2. migration assistant?
3. reinstall using disks/installers?

If they are only in the former system you forgot to to preserve your user settings.
How to Archive & Install:
http://docs.info.apple.com/article.html?artnum=107120

Cannot log in after archive and install

Hello, everyone. ive been searching the support pages of the apple site for an hour and i cannot seem to find a resolution to this...
I just peformed an archive and install ad now i cannot log in. i think this happened once before and i called apple support and i was told to log in as root. the problem i am having is that the login window does not give me the option to change the user field, it only allows me to type a password. every time i type my password, the login screen shakes. so even if i wanted to type root into the user field, i cant. any suggestions would be greatly appreciated. thank you.
p.s. i was running tiger but lost my tiger disc so i am using the disc that originally came with my g5 which has panther on it...
dayna

Hi, Dayna.
1. Be sure the Caps Lock key isn't active: passwords are case sensitive. You may see an exclamation point on the right side of the password field if the Caps Lock key is engaged.
2. There was a similar problem if one performed an Archive and Install (A&I) of Jaguar (10.2) over Panther (10.3): see "Can't log in after installing Mac OS X 10.2 over 10.3." I've not heard of a similar problem with performing and A&I of Panther over Tiger, but it may be related. However, before trying the advice therein to perform the A&I without selecting "Preserve Users and Network Settings" you'd need to have a backup of your data, otherwise you risk losing everything in your account. IMO, the most expedient solution would be to buy a replacement Mac OS X Tiger disc. If there is an Apple Retail Store in your area, that would be the quickest place to purchase one.
Good luck!
Dr. Smoke
Author: Troubleshooting Mac® OS X

Lost MPEG-2 after archive and install

I bought and used the MPEG-2 playback component but MPEG Streamclip no longer believes it is installed after a recent archive and install of Leopard.
I still have my confirmation email of purchase, but there's no indication as to how to reinstall or repair MPEG-2.
What do I need to do to restore Quicktime and especially MPEG-2?

I'd recommend saving your (paid-for) QuickTimeMPEG2.dmg file on your local disk. This would go for any software you pay for and then download online, especially if it can be accidentally wiped out by an OS upgrade.

Quicken 07 remains after Archive and Install?

Will the Quicken 07 application AND all my accounts remain after doing Archive and Install? I mean, will they be up and ready to use or need to be located in a folder and re-installed?

On an "Archive and Install", you have the option to save user data and network settings. This will copy all your user data into the home directory on the new install, and make the install process as seamless as possible. Applications are copied over as well, I believe, but if they're not they are left in the "Previous System" folder and you can copy them over manually and test them out. I believe "Quicken" is one of those applications where you just drag it to the applications folder to install it. As such, it should migrate to the new system easily and be up and running without the need to reinstall it. Most apps that require reinstalls are those that put extensions and plug-ins into the system folder (Adobe CS3, for example). Some things to keep in mind:
Corrupt preference files can cause applications to run funny or not at all. If an app doesnt behave normally then remove the preference file for that application from your user library. Corrupt preference files can happen during an install, so its good to be aware of the possibility they might crop up.
In a similar manner as corrupt preference files, sometimes the install process can change the permissions on files and folders, which will result in the same funky behavior. Using Disk utility to fix permissions BEFORE and AFTER the install will greatly reduce the probability of this being an issue.

I Lost Parallels After Archive and Install

I posted this on the Parallels Forum, and although it was viewed 59 times, there were no replies. So I'm posting it here hoping that someone can/will answer my question. Here's what I posted:
My OS X (10.4.11) became a little quirky after three years so I did an Archive and Install. Now I can't get Parallels to start up my Windows XP virtual machine. I get the error message "Parallels Desktop is unable to operate properly since it cannot communicate with one of its drivers ... re-install Parallels Desktop." I have my original Parallels 3.0 installation CD so I suppose I can figure out how to do this. (My iMac was purchased with Parallels pre-installed.) Do I need to uninstall before I re-install? I have on my desktop the Parallels alias labeled "Microsoft Windows XP.pvs" plus I have in Applications an alias labeled "Parallels Desktop". If I need to uninstall, can I just drag these two to the trash? I am not adept at this sort of thing, so I need some guidance. Thanks.

Hmmm...good question, I'm not sure. I believe all you would have to do is be able to at least bring up the Parallels Window and have at least "Paralells" recognize still that there is a virtual machine there, not necessarily be able to get into it. Can you at least pull up the parallels window and/or box that you would normally pull up to list your virtual machines? If you cannot do at least this, then you're probably stuck re-installing Parallels. But please remember to back up your virtual machine file in another area like an external hard drive before you do the re-install. Installing and un-installing parallels is NOT SUPPOSE to mess with your virtual machines, but I wouldn't bank on it. If you can at least bring up that Window/Box, then you could use the are listed on the box to re-install the Tools. Hope it works out for ya.

'Transport Monitor' error after archive and install....?

The application "Transport Monitor" could not be launched because of a shared library error: "8<Transport Monitor><Transport Monitor><HotSyncLib.PPC>"
Thats the error reading I get after I performed an archive and install of 10.4.6.
Any ideas?

Hello!
A quick search of the KB came up with this article, hopefully it'll help you out!
http://docs.info.apple.com/article.html?artnum=25578
Name a Mac, and I've used it. I Promise. Mac OS X (10.4.6)

Excessive HD usage after archive and install.

Similar Messages

Maybe you are looking for