Exchange 2007/2013SP1 mailbox (15GB) migration stalled.

We have successfully migrated all our mailboxes from Exchange 2007 to Exchange 2013SP1, except one mailbox with the 15GB size, which stalled at 95%, even we tried "Resume-MoveRequest",
but again the same error:
Here is the error:
4/14/2014 10:37:56 AM [XXXXXXXX] Stage: IncrementalSync. Percent complete: 95.
4/14/2014 10:37:56 AM [XXXXXXXX] Fatal error TooManyMissingItemsPermanentException has occurred.

Can you tell us more please. I have the same problem. I changed the value to
ContentVerificationMissingItemThreshold = 100, 100, MaxInt
And that didn't help. Can you tell us what you did specifically.
Thanks
E

Similar Messages

Exchange 2007 shared mailbox

How do you connect an exchange 2007 shared mailbox to your iphone? Normal "user" mailboxes work just fine. Is this supported by Apple and or Microsoft?

Hi
You can not control this behaviour from Exchange. This is controlled by Outlook.
Outlook chooses the from address from what additional mailbox you are replying from (just as you see :-))
There are a lot of registry tweaks for Outlook, but I don't think there are one to control this.
I see 3 possible sollutions.
1. The users can choose them self
2. You give the users "Send As" permissions on the mailbox
3. you use this tool
http://www.ivasoft.biz/setfrom2013.shtml
BR
Steen

Exchange 2007 Export-Mailbox Error Message on only certain mailbox

I have searched high and low for a solution to this, but no such luck. Hopefully someone has had the same issue and can help me out.
I am attempting to export and then remove a date range for mailboxes before I migrate to an Exchange 07 server. The mailboxes range in the 10 GB range. I am attempting to use the Exchange 2007 cmdlet to do this with due to it does not have a 2 GB limit like the Exmerge of past.
The command I am using is as follows:
[PS] C:\>Export-Mailbox -Identity User -StartDate "01/01/07" -EndDate "01/30/08"
-IncludeFolders "\Inbox","\Sent Items" -PSTFolderPath c:\PST\pst.pst
This command works fine on some of the mailboxes in the Exchange03 system. But on some of the mailboxes I am getting the following error.
Error occurred in the step: Moving messages. Failed to copy messages to t
he destination mailbox store with error:
MAPI or an unspecified service provider.
ID no: 00000000-0000-00000000, error code: -1056749164
Any ideas?

Hello Joe Rod (and others)
Thought I'd bring this over as a cross post because no-one seems to be picking it up in the 'admin' section. I believe I'm having a similar issue to yourself, as detailed below:
Hi all,
I've already posted this same question elsewhere, but if anyone here can resolve the issue or suggest a better way (without using archiving software - yet!), I'd be most grateful. I'd even be happy if someone can replicate the problem so I know I'm not going mad... I'm trying to set up a quick & dirty quarter year pst mail archive for one of our users on our Exchange 2007 (SP1) box. Using the command:
export-mailbox -id userA -pstfolderpath \\testpath\test.pst -enddate "01/03/2007"
I come up against this error:
Error occurred in the step: Moving messages. Failed to copy messages to the destination mailbox store with error: MAPI or an unspecified service provider. ID no: 00000000-0000-00000000, error code: -1056749164
Which I understand is a fairly standard permissions error. Problem is that I know the permissions are set correctly, having tested the function by removing the -enddate parameter; and getting a successful export.
I worked out after a while that the command seems to fall over when it hits a subfolder, so I tested this by using the -includefolders parameter. The command:
export-mailbox -id userA -pstfolderpath \\testpath\test.pst -includefolders '\inbox' -enddate "01/03/2007"
will fail if there are any subfolders under '\inbox'. Add the names of the subfolders:
export-mailbox -id userA -pstfolderpath \\testpath\test.pst -includefolders '\inbox\subfolder1' -enddate "01/03/2007"
and as long as those subfolders don't have any subfolders, I will get a successful export.
Any help appreciated.
Cheers
Dan
If anyone is able to replicate this, please let me know, I'd love to get this sorted. If it is a known problem - can I use someone's PSS contact please?!

Looking for Script Exchange-2007: Import-Mailbox Calendar Folder on multiple mailboxes {Distribution Group}

Hi,
I'm looking for a PowerShell script which will import a Calendar events into student's mailbox (Calendar). Those students are located in a distribution group and I would like to target the distribution group; I'm trying to simulate what I want to achieve
in the below code example, I would appreciate if anyone jump in and advise.
$Users = Import-Csv C:\users.csv | ForEach-Object{Get-DistributionGroup -Identity SC-1213} | Import-Mailbox -Identity $Users -PSTFolderPath c:\Calendar.pst -IncludeFolders '\Calendar' -StartDate -EndDate
Much appreciated..
Hussain

The logic doesn't work unless you are using StartDate and EndDate for the period when you change the item. As I said above, StartDate and EndDate are not the times when the meeting starts and ends - they are the times that the item was either added
or modified in the mailbox. Your filter was trying to pull items that were in the future.
And as I also said above, if you import a modified item, the original is
not going to be updated. You will have a duplicate meeting
on the calendar. You would have to remove the original
and import the updated item if this was how you wished to manage the updates. This is not nearly as effective as
sending meeting requests and updating those meetings.
For example, if we do things the way you are doing them, and we add a "Student Appreciation Bonfire" meeting to the calendar for April 12 at "The Quad", we would do the following:
On February 1, you get information for the meeting that needs to be imported
You create this new meeting in the PST calendar - "Student Appreciation Bonfire"; Date April 12, start 8:00 AM, end 12:00 noon; Location The Quad
You import the PST into everyone's calendar
You receive a note on March 12 saying the venue has changed to The River Beach, so you update this meeting in your PST
Since there are other calendar items in the PST, you import the update using StartDate of March 12 and EndDate of March 13 - the date that you changed the item, not the date the item occurs
At this point, all users have two meetings on their calendar - the original and the update
If, instead of doing it this way, you create a Student Actvities Calendar mailbox, you would handle it this way:
On February 1, you get information for the meeting that needs to be imported
You create this new meeting in the Corporate calendar - "Student Appreciation Bonfire"; Date April 12, start 8:00 AM, end 12:00 noon; Location The Quad
You invite everyone to the meeting
You receive a note on March 12 saying the venue has changed to The River Beach, so you update this meeting in that calendar and send out the update
At this point, all users have only the one meeting on their calendar - the update
Using the PST as the source for the meetings would work only for items that
will not be changed - holidays are a good example.

Exchange 2007/2010 Environment (In Migration Currenty) Outbound Mailflow issues

Hello,
I have an issue that started Friday and keeps progressing. On friday my Spam filter started freaking out with numerous emails I though it was the filter but it appears it is one of the servers instead. The errors stopped and I thought I was good
however I then realized no email was flowing. I checked and found on the 2010 server my disk space had dropped low (under 1gb) and it shutdown my transport, I increased the size now has (40gb free) and restarted the transport services and bang I had
email for a few hours. However that was shortlived I am getting the following errors in the 2007 server queue now:
Date Received: 12/15/2013 9:32:43 PM
Expiration Time: 12/17/2013 9:32:43 PM
Last Error: 452 4.3.1 Insufficient system storage
Queue ID: MAIL\3
Now, I've check on the 2007 server I have 100gb free on the C drive and 500gb free on the D drive which stores the database. So I have no storage issues, I was also getting errors in the event log for backflow issues stating I was out of storage space.
However everything is good now on both servers. My 2010 server has 40gb free on the C drive now and 290gb free on the D drive now. For the heck of it I tried to disable the resource monitoring on the 2007 server for now, however I get the same
error message when trying to send email still. I even went as far as rebooting the server.
This whole weekend has gone from bad to worse, anyone have any suggestions or please tell me what additional information would be needed to help troubleshoot this?
Thanks,
Greg

Hello,
Please check if the Mail.que file grows larger on HUB transport server. If so, please delete it as the following article:
http://msexchangeguru.com/2011/06/02/mail-que/ (Please Note: Since the web site is not hosted by Microsoft, the link may change without notice. Microsoft does not guarantee the accuracy of this information)
Please disable anti-virus software temporarily to check the result.
And please check if there is any error in application log.
Cara Chen
TechNet Community Support

Exchange 2007 Resource mailboxes no longer auto accepting meeting requests

Ww have a large number of meeting rooms/resources, until today they were auto accepting meeting/booking requests and responding to the requester, if there was a conflict it auto rejected and advised the requestor of the conflict.
Today, none of them are accepting or responding.
I went into one of these via OWA and everything is set correctly, no changes have been made that I am aware of. Using EMS I ran the cmdlet  MailboxCalendarSettings <resourceID>| fl, the result was:
AutomateProcessing                  : AutoAccept
AllowConflicts                      : False
BookingWindowInDays                 : 180
MaximumDurationInMinutes            : 1440
AllowRecurringMeetings              : True
EnforceSchedulingHorizon            : True
ScheduleOnlyDuringWorkHours         : False
ConflictPercentageAllowed           : 0
MaximumConflictInstances            : 0
ForwardRequestsToDelegates          : True
DeleteAttachments                   : False
DeleteComments                      : True
RemovePrivateProperty               : True
DeleteSubject                       : True
DisableReminders                    : True
AddOrganizerToSubject               : True
DeleteNonCalendarItems              : True
TentativePendingApproval            : True
EnableResponseDetails               : True
OrganizerInfo                       : True
ResourceDelegates                   : {}
RequestOutOfPolicy                  :
AllRequestOutOfPolicy               : False
BookInPolicy                        :
AllBookInPolicy                     : True
RequestInPolicy                     :
AllRequestInPolicy                  : False
AddAdditionalResponse               : False
AdditionalResponse                  : <DIV><FONT size=2
                                      face=Tahoma></FONT></DIV>
RemoveOldMeetingMessages            : True
AddNewRequestsTentatively           : False
ProcessExternalMeetingMessages      : False
DefaultReminderTime                 : 0
RemoveForwardedMeetingNotifications : True
Identity                            : Domain.com/Resources/Conference Room
                                      resource ID
IsValid                             : True
ObjectState                         : Unchanged
As far as I can see, this is all correct, but the resource, along with ALL others, have stopped accepting meetings/bookings and are not responding to requests.
Does anyone have an idea what has happened and how I can fix this?
NOTE:
In an attempt to resolve this, I used
Set-MailboxCalendarSettings <ResourceID> -AutomateProcessing:Autoaccept
No change has been seen

I wonder when the majority of people will understand that the best decisions are made close to the coffee machine and not in a conference room :)
Glad to hear that it worked for you though.
Martina Miskovic

Exchange active sync cannot connect to server after migration mailbox user from exchange 2007 to exchange 2013 coexistence

Hello, everyone, my name is rafl
I have a problem with exchange 2013 active sync.
I have installed exchange 2013 coexistence with legacy exchange 2007, I have to migrate user mailboxes: [email protected] from exchange 2007 to exchange 2013.
but any problem with active sync connection on the mobile device after moving mailbox user. I reconfigure the exchange ActiveSync external connection domain (latest.domain.com) on mobile device replacing legacy exchange ActiveSync external connection domain
(legacy.domain.com)
the process of moving mailboxes successfully without error.
Access OWA for exchange 2007 and exchange 2013 is running normally
access mail from Outlook running normally
Certificate request has been installed and has no problem with it
The OWA virtual directory is configured for internal and external connections and different from the legacy exchange
The autodiscover virtual directory is configured for internal and external connections and different from the legacy exchange
ActiveSync virtual directory is configured for internal and external connections and different from the legacy exchange
user mailboxes are still on exchange 2007 is not problematic.
only problem with Exchange Active Sync on mobile devices, where I set up an email with android, iphone, windows phone. the error message: cannot connect to the server.
but, if I create a new user and create user mailboxes directly in exchange server 2013, ActiveSync can run without error on mobile device, access through OWA, MsOutlook, Outlook Anywhere also run normally.
only the results of user migration from exchange 2007 to exchange 2013 which is troubled with exchange ActiveSync connection.
any ideas for this problem, and what should I check on the exchange server ..?

i have run the activesync test connectivity and get some error :
Testing TCP port 443 on host domain.co.id to ensure it's listening and open.
The specified port is either blocked, not listening, or not producing the expected response.
A network error occurred while communicating with the remote host.
Elapsed Time: 3091 ms.
Testing TCP port 443 on host autodiscover.domain.co.id to ensure it's listening and open.
The specified port is either blocked, not listening, or not producing the expected response.
A network error occurred while communicating with the remote host.
Elapsed Time: 21072 ms.
Testing TCP port 80 on host autodiscover.domain.co.id to ensure it's listening and open.
The specified port is either blocked, not listening, or not producing the expected response.
A network error occurred while communicating with the remote host.
Elapsed Time: 21049 ms.
I have allowed access to port 443 (https) and 80 (http) on the firewall and re-run testconnectivity, but still with the same results. if I enable active sync for users who created directly in Exch 2013 there is no problem with the ActiveSync, just a problem
for users who moved from Exch 2007 to Exch 2013. @Android, iPhone, and Blackberry the error message "cannot connect to the server"

Exchange 2007 to Exchange 2010 cross forest simultaneous mailbox move limits

Hi All,
I am testing the throughput of mailbox moves from Exchange 2007 to Exchange 2010 cross forest. Single mailbox moves seem to be quite fast and I am not concerned about network, disk IO or server resource limitations, however I have not tested multiple simultaneous
mailbox moves to determine what the Exchange limitations are. If anyone could identify the limitations of the items below it would be much appreciated:
Limit of Exchange 2007 simultaneous mailbox moves per database
Limit of Exchange 2007 simultaneous mailbox moves per Mailbox server
Limit of Exchange 2007 simultaneous mailbox moves per CAS server
Limit of Exchange 2010 simultaneous mailbox moves per database
Limit of Exchange 2010 simultaneous mailbox moves per Mailbox server
Limit of Exchange 2010 simultaneous mailbox moves per CAS server
Any other Exchange 2007 or 2010 hard coded limits
Thanks in advance.
Michael.

My usual answer to this question is that Microsoft set these limits for a reason. Increasing them may not offer you much in the way of benefits if you end up slamming the server. I generally recommend that you leave them alone.
I have had occasional opportunities to change these constraints, most notably back during a migration to Exchange 2003 and international mailbox moves (Asia to U.S.) where the limiting factor was network latency. I was able to increase the number of
concurrent threads to 16 from the default 2 and there was still available bandwidth because the process was limited by the latency.
Ed Crowley MVP "There are seldom good technological solutions to behavioral problems."

Veiwing mailbox sizes in exchange 2007

Is it me or is Exchange 2007 missing mailbox size? i cant anywhere to veiw the size of a users mailbox.

Sunil;
Never use a Format- cmdlet before sending data to Export-Csv
Use Select-Object instead.
PowerShell V1:
Get-MailboxStatistics -Database "Mailbox Database" |Select-Object DisplayName, LastLoggedOnUserAccount, ItemCount, @{expression={$_.totalitemsize.value.ToMB()};label=”Size(MB)”}, LastLogonTime, LastLogoffTime | Export-Csv MailboxSize.csv -NoTypeInformation
PowerShell V2:
$MailboxStatistics = @{
Database = "Mailbox Database"
$Select = @{
Property = "DisplayName","LastLoggedOnUserAccount","ItemCount",
@{expression={$_.totalitemsize.value.ToMB()};label=”Size(MB)”},
"LastLogonTime","LastLogoffTime"
$Csv = @{
Path = "MailboxSize.csv"
NoTypeInformation = $true
Get-MailboxStatistics @MailboxStatistics |Select-Object @Select |Export-Csv @Csv
Karl
http://unlockpowershell.wordpress.com
-join("6B61726C6D69747363686B65406D742E6E6574"-split"(?<=\G.{2})",19|%{[char][int]"0x$_"})

Redirection loop detected while opening Exchange 2007 mailboxes through Exchange 2013 OWA page

Team, in our infra Exchange 2013 CU8 & Exchange 2007 SP3 RU15 running. Exchange 2013 recently deployed but while opening exchange 2007 users mailbox through 2013 OWA getting error "Redirection loop detected". Want to update you few things :
Public DNS record created as mail.myinfra.in with x.x.x.2 IP and legacy.myinfra.in with x.x.x.3 IP.
Virtual directory modified mail.myinfra.in for 2013 & legacy.myinfra.in for 2007.
All the OWA request need to pass through public DNS only no internal DNS record for OWA.
Through ISA already rule created and tested also like https://mail.myinfra.in/owa giving me 2013 OWA page & https://legacy.myinfra.in/owa giving 2007 owa page. Only problem while opening https://mail.myinfra.in/owa with 2013 mailbox id/pwd working fine
but with 2007 mailbox id/pwd giving error "Redirection loop detected".
Appreciate if you can help quickly.

Hello
tip: check iis log on both of exch servers and check owa application haven't got "HTTP redirect" enabled.
sorry my english

Clean remote Mailbox after migration

Hello ,
I am Migrating mailbox users form Exchange 2007 to Exchange 2010 SP3 some users after Migration there Mailbox still in exchange 2007 as mailbox user instated of mail user and in exchange 2010 as mail box user .
but its for some users .
can you help me please why it happen

Hi,
Do you mean the mailbox in the original mailbox change to the soft-deleted state?
If so, I recommend you check MAS's suggestions.
When mailboxes are moved from an Exchange 2010 SP1 database to any other database, Exchange doesn't fully delete the mailbox from the source database immediately upon completion of the move. Instead, the mailbox in the source mailbox database is switched
to a soft-deleted state. For more details about this, you can refer to the following article.
http://technet.microsoft.com/en-gb/library/dd298174(v=exchg.141).aspx#SoftDel
Hope this is helpful to you.
Best regards,
Belinda Ma
TechNet Community Support

Exchange 2007 setup, transitioning from Exchange 2003

Hello Exchange Experts,
I just setup a Exchange 2007 within our domain, transistioning from Exchange 2003, question: When I added the mailbox role on the setup of Exchange 2007, the mailboxes appeared instantly from our Exchange 2003..the connector I'm assuming automatically connected
during the 07 setup. Is this normal? I was under the assumption to migrate mailboxes from 03 to 07 Exchange, the wizard must be ran. All active mailboxes from 03 appear. I attempted to migrate one mailbox using the wizard, error after the wizard completed,
mailbox exists. Makes sense, just not understanding how the mailboxes flowed/migrated automatically without running the migration steps. Would someone explain? You could say, this migration is very new to me.
Thanks in advance!
James

Ronny, our company had an existing license for 2007. Of courser 2010 or 2013 would have been a better transition, but 2007 is it. The server 2007 has met all the criteria for the transition, spent last moth prepping everything on 2003 and 2007. I'm just
not understanding why the mailboxes appeared upon 2007 immediately after adding the mailbox role. The management console on 07 shows the mailboxes reside on 03 exchange server. I did not go through the process/wizard to move to 07. Perhaps because
during the installation of Exchange 07 created the connector from 2003? Maybe that's my question.
Mail flow is very responsive now, just wondering for the reasons of decommissioning exchange 2003 at a later date. Exchange 2003 is functioning now as a bridgehead, working perfectly now.
Thanks for your input.
James
Thanks Ronnie for your input! Issue resolved

Incorrect Legacyexchangedn is being stamped only on contact objects created on Exchange 2007

Environment
Exchange 2007- All mailboxes are hosted on Exchange 2007 servers.
Exchange 2000 - Only being used to relay emails, RUS is running on these servers.
Abnormality what i have noticed is that contact objects being created on exchange 2007 server are getting legacyexchangedn as "OU=itca" which is name of Exchange 2000 administrative group. Ideally, any objects created on Exchange 2007 should get
legacyexchangedn like "OU=Exchange administrative group (FYDI....)" .
This happens only with contacts. Legacyexchangedn on mailbox is getting stamped correctly.
I am trying to understand why contact objects are getting incorrect legacyexchangedn. Any help on this would be appreciated.

Hi,
Can you change the OU when create contacts?
Please try below link to create contact, for your reference:
https://technet.microsoft.com/en-us/library/aa997220(v=exchg.80).aspx
Meanwhile, we can modify the default OU by AD. More details about Redirecting the users and computers containers in Active Directory domains, please refer to:
http://support.microsoft.com/kb/324949/en-us
Best Regards,
Allen Wang

Compatibility between Exchange 2007 service packs

Hi all, I have 5 servers Exchange:
- 3 Servers CAS and HUB
- 2 Servers Mailbox server in Microsoft Failover Cluster (MSCS)
Domain Controllers are all
Windows Server 2003 SP2
The versions of Exchange 2007 SP1 servers are all:
8.1 Build 240.6
I have thought about installing SP3 and RU13 in all 5 servers for Exchange, but I'm going to install SP3 and RU13 on 2 servers CAS / HUB and the following week at the other CAS / HUB server.
Finally, the following week in the two Mailbox Servers.
Is there any problem if I miss 2 servers CAS / HUB with SP3 RU13 and the other CAS / HUB in SP1, this will only be for a few days?
Is there any problem if I leave the servidors Mailbox Servers in SP1 while CAS / HUB are in SP3 RU13, this will only be for a few days?
regards
Microsoft Certified IT Professional Server Administrator

Hi Yupikaiey.
Only thing you should be concerned is if you have CAS-CAS proxy or the Mailbox Cluster part.
Your current plan looks good. Just stay alert for any uncommon issues popping up, which would normally mean due to the difference.
If you upgrade your servers in this order, you may avoid potential service interruptions.
Details below:
Version Constrains are more of between roles of 2007-2010-2013 and not between same version SPs or RUs.
Exchange 2013 Server Role Architecture
The Past: Exchange 2007 and Exchange 2010
Our goal was to make these server roles autonomous units. Unfortunately, that goal did not materialize in either Exchange 2007 or Exchange 2010. The server roles were tightly coupled along four key dimensions:
2.This also necessitated a tight versioning alignment – a down-level Hub Transport or Client Access shouldn’t communicate with a higher version Mailbox server; in some cases this was enforced (e.g., Exchange 2007 Hub Transport servers cannot deliver messages
to Exchange 2010 Mailbox servers), but in other cases they were not (e.g., an Exchange 2010 SP1 Client Access server can render data from an Exchange 2010 SP2 Mailbox server).
The versioning restriction also meant that you could not simply upgrade a single server role to take advantage of new functionality – you had to upgrade all of them.
The Present: Exchange Server 2013
If I upgrade the Mailbox server with a service pack or cumulative update, then for a given mailbox hosted on that server, all data rendering and content conversions for that mailbox will be local, thus removing version constraints and functionality issues
that arose in previous releases.
Exchange 2007 Servicing
http://technet.microsoft.com/en-in/library/dd421853(v=exchg.80).aspx
Deployment Order
Our test infrastructure guarantees that Exchange hotfixes work across multiple server roles. The order in which you apply the update rollup to the servers is not important except if you are deploying CAS-CAS proxying. Because the update rollups are not segmented
for different Exchange server roles or for specific file configurations, apply each update rollup package to all Exchange 2007 servers in your environment.
If you have multiple Active Directory sites, and if you deploy a Client Access server in the proxy sites that do not face the Internet, you must
apply the update rollup to the Internet-facing Client Access servers
and to the non-Internet-facing Client Access servers in the proxy site simultaneously. For other Exchange 2007 configurations, we recommend that you
apply the update rollup package to the Client Access servers before
you apply it to servers that are running other Exchange 2007 server roles, such as the Mailbox server role, the Hub Transport server role, and the Edge Transport server role.
Note:
Applying service packs and update rollups to clustered Mailbox servers requires specific planning and application steps. For more information about how to apply service packs to Exchange 2007 clustered Mailbox servers, see
Upgrading Clustered Mailbox Servers to Exchange 2007 SP1 or later. For more information about how to apply update rollups to Exchange 2007 clustered Mailbox servers, see
Applying Exchange 2007 Update Rollups to Clustered Mailbox Servers.
For Patching and compatibility between versions:
Determine the service pack level of Exchange.
Update rollups are service pack dependent. For example, an Update Rollup 5 package is available for Exchange 2007 and for Exchange 2007 Service Pack 1. To determine the service pack level of Exchange, examine the
ExchangeVersion property. For more information about how to view the
ExchangeVersion property and about the build number that is associated with each Exchange version, see
Exchange Server 2007: Platforms, Editions, and Versions.
References:
How to Install the Latest Service Pack or Update Rollup for Exchange 2007
Exchange Server Updates: build numbers and release dates
We are looking at doing the roll-up to SP3
Coexistence of Exchange2007 SP1 and Exchange 2007 SP3
Regards,
Satyajit
Please “Vote As Helpful”
if you find my contribution useful or “Mark As Answer” if it does answer your question. That will encourage me - and others - to take time out to help you.

Exchange 2007 Room Calendar Issues

Hello, on our Exchange 2007 server, we have 6 room mailboxes, all setup exactly alike. One of the mailboxes started not responding to calendar requests. If I schedule a meeting, exchange does it's part, and sends out the invitation, but nothing shows in
the room calendar itself. Besides exporting the existing calendar entries and creating a new mailbox, is there anything I can try?
[PS] C:\Windows\System32>Get-MailboxCalendarSettings RadcliffeConf.Room | fl
AutomateProcessing : AutoAccept
AllowConflicts : False
BookingWindowInDays : 180
MaximumDurationInMinutes : 1440
AllowRecurringMeetings : True
EnforceSchedulingHorizon : True
ScheduleOnlyDuringWorkHours : False
ConflictPercentageAllowed : 0
MaximumConflictInstances : 0
ForwardRequestsToDelegates : True
DeleteAttachments : True
DeleteComments : True
RemovePrivateProperty : True
DeleteSubject : True
DisableReminders : True
AddOrganizerToSubject : True
DeleteNonCalendarItems : True
TentativePendingApproval : True
EnableResponseDetails : True
OrganizerInfo : True
ResourceDelegates : {}
RequestOutOfPolicy :
AllRequestOutOfPolicy : False
BookInPolicy :
AllBookInPolicy : True
RequestInPolicy :
AllRequestInPolicy : False
AddAdditionalResponse : False
AdditionalResponse :
RemoveOldMeetingMessages : True
AddNewRequestsTentatively : True
ProcessExternalMeetingMessages : False
DefaultReminderTime : 15
RemoveForwardedMeetingNotifications : False
Identity : xxxx.com/SDI Users Groups and Computers/
Room Mailboxes/Radcliffe Conf. Room

Hi n3lka
Thank you for your question.
Owing to not respond, you can try to check the mailbox permission.
“nothing show in the room calendar itself”, you can make outlook in cache mode, then, you can try to uncheck option “Download share folders”.
There is a similar thread you can refer to by the following link:
https://social.technet.microsoft.com/Forums/en-US/cb057c90-9eaa-4ead-8b1d-68e8ae87c0b0/exchange-2007-room-calendar-issues?forum=exchangesvrclientslega
when nothing shows in the room calendar itself, you can try to make another user schedule a meeting, if another user schedule a meeting successful, you can refer to the following link to solve it:
https://social.technet.microsoft.com/Forums/en-US/a31af989-aee1-42f0-88bd-c178c6199379/exchange-2007-room-mailbox-and-calendar-issue?forum=exchangesvradminlegacy
If there are any questions, please let me know.
Best Regard,
Jim

Exchange 2007/2013SP1 mailbox (15GB) migration stalled.

Similar Messages

Maybe you are looking for