Exchange 2010 SP1 management console fail

Exchange 2010 SP1 management console fail on local exchange servers.
The following error occurred while attempting to connect to the specified Exchange server CAS123.domain.co.za
The attempt to connect to
http://cas123.domain.co.za/PowerShell using “kerberos” authentication failed: Connecting to remote server failed with following error message: The WS-Management service cannot process the request because IP address cas123.domain.co.za is invalid. For more
information, see the about_Remote_Troubleshooting Help topic.
However do note that the Exchange Management Shell also fails with the exact same error on both my CAS and Mailbox servers.
Though I am still able to open both tools via my backup server.
All ells works fine.
nslookup resolves the exchange servers as they should be. Frankly I am stumped as to the invalid IP address.
My exchange environment have been running problem free for years and this problem only occurred last week Thursday after some .NET updates.

Hi,
As per the information and details provided by you, the only thing that I can figure out is that: -
You receive an error: Exchange 2010 SP1 management console fail.
There are two methods to resolve this problem: -
Method 1: -
Close all MMC/EMC instances before proceeding.
Open the Registry editor (regedit) as the user you run the EMC under.
Go to
HKEY_CURRENT_USER\SOFTWARE\Microsoft\ExchangeServer\v14\AdminTools
Look for value, Node structure setting.
If it is there, back it up and then remove it.
Method 2: -
Close all MMC/EMC instance before proceeding.
Open powershell or powershell IDE as the user you run the EMC under and execute the following command:
Remove-Item Property- Path
HKCU:\Software\Microsoft\ExchangeServer\v14\AdminTools\ -Name NodeStructureSettings
Close Powershell
I hope this information will be helpful for you. Correct me if the information that I am having is wrong.
Thanks and regards
Ashish@V

Similar Messages

Cannot upgrade Exchange 2010 SP1 Management Tools to SP2 on Win 8.1 workstation

I have a Win 8.1 workstation that I am trying to update the Exchange Management tools on from 2010 SP1 to SP2. I get an error that says:
Error:
The following error was generated when "$error.Clear(); &RoleBinPath\ServiceControl.ps1 EnableServices Critical" was run: "AuthorizationManager check failed.".
The WMI service is being disabled and not starting back up after, causing the error. I have tried the following:
-Confirmed that the ExecutionPolicy is set to undefined/unrestricted for the localmachine
-Confirmed no GPO exists in our domain to restrict this
Every single time I run the install the WMI service switches to disabled and the localmachine Execution Policy is switched to RemoteSigned.
I have tried the Google search steps except for the Setup /M:Recoverserver since I really don't know what that would do to our Exchange environment. I have seen some posts that the Exchange 2010 MGMT tools are not supported on Win 8, which I find hard to
believe. I get no unsupported error just this incredibly frustrating error.
Any ideas?

What you are doing is totally unsupported:
http://technet.microsoft.com/en-us/library/ff728623(v=exchg.150).aspx
By the way, Exchange 2010 sp1 and SP2 are no longer supported, the minimum supported is SP3.
http://social.technet.microsoft.com/Forums/en-US/b3085dd9-6777-454e-af30-279dfccffb8b/exchange-2010-sp1-and-sp2-are-no-longer-supported?forum=exchange2010
Please take a moment to Vote as Helpful and/or Mark as Answer where applicable. Thanks.

Exchange 2010 SP1 OWA login fail "The username or password you entered isn't correct. Try entering it again"

I upgrade my Exchange ORG from Exchange 2007 to Exchange 2010 on Windows Server 2008 R2 and worked fine. After install Exchange Server 2010 SP1 have a problem with
the Outlook Web App, I cannot login an get this error:
"The username or password you entered isn't correct. Try entering it again"
1. Create 1 test user and all work, included the Administrator User.
2. Reset users Password, verify clear check " User must change password at next logon"
2. I set the OWA Authentication to Domain\user name and
User name only, Doesn't work with both ways.
also i tried this solution, but nothing....
http://social.technet.microsoft.com/Forums/en/exchange2010/thread/961dbdd0-554f-4a75-a374-7ada899a2807
Thank´s everybody por reply
Bryan

can you login using that user account using RDP to the Exchange serverRegards, Mahmoud Magdy Watch Arabic Level 300 Videos about Exchange 2010 here: http://vimeo.com/user3271816 Read pretty advanced Exchange stuff I post here: http://www.enowconsulting.com/ese/blog.asp, follow my blog: http://autodiscover.wordpress.com ,
corp blog: http://ingazat.wordpress.com and if you Liked my post please mark it as helpful and accept it as an answer

Exchange 2010 SP1 install fails with -1603 error

I am getting a -1603 error when installing Exchange 2010 SP1. Installation fails when copying files/removing old version with the following error:
[10/01/2010 23:17:06.0823] [2] Beginning processing uninstall-MsiPackage -ProductCode:'6574fdc2-40fc-405a-9554-22d1ce15686b' -LogFile:'C:\ExchangeSetupLogs\InstallSearch.msilog'
[10/01/2010 23:17:06.0847] [2] Removing MSI package with code '6574fdc2-40fc-405a-9554-22d1ce15686b'.
[10/01/2010 23:17:09.0400] [2] [ERROR] Unexpected Error
[10/01/2010 23:17:09.0401] [2] [ERROR] Couldn't remove product with code 6574fdc2-40fc-405a-9554-22d1ce15686b. Fatal error during installation. Error code is 1603.
[10/01/2010 23:17:09.0401] [2] [ERROR] Fatal error during installation
[10/01/2010 23:17:09.0409] [2] Ending processing uninstall-MsiPackage
[10/01/2010 23:17:09.0411] [1] The following 1 error(s) occurred during task execution:
[10/01/2010 23:17:09.0412] [1] 0. ErrorRecord: Couldn't remove product with code 6574fdc2-40fc-405a-9554-22d1ce15686b. Fatal error during installation. Error code is 1603.
Does anyone know how to resolve this?
Thanks,
greg

Hi Frank,
I've the same problem when I try to install the SP2.
When I try to install RU 4v2, 5 or 6, then comes error 2771. So I waiting for SP2 in the hope, a full install of the SP will fix this.
But the setup broke with the following entries:
[12.07.2011 19:51:59.0379] [0] Setup will run the task 'uninstall-msipackage'
[12.07.2011 19:51:59.0379] [1] Setup launched task 'uninstall-msipackage -logfile 'C:\ExchangeSetupLogs\ExchangeSetup.msilog' -ProductCode '4934d1ea-be46-48b1-8847-f1af20e892c1' -PropertyValues 'BYPASS_CONFIGURED_CHECK=1 DEFAULTLANGUAGENAME=DEU''
[12.07.2011 19:51:59.0379] [1] Die Active Directory-Sitzungseinstellungen für 'Uninstall-MsiPackage' lauten: Vollständige Gesamtstruktur anzeigen: 'True', Konfigurationsdomänencontroller: 'LicPDC.kh-lichtenstein.local', Bevorzugter globaler Katalog:
'LicPDC.kh-lichtenstein.local', Bevorzugte Domänencontroller: '{ LicPDC.kh-lichtenstein.local }'
[12.07.2011 19:51:59.0379] [1] Beginning processing uninstall-msipackage -LogFile:'C:\ExchangeSetupLogs\ExchangeSetup.msilog' -ProductCode:'4934d1ea-be46-48b1-8847-f1af20e892c1' -PropertyValues:'BYPASS_CONFIGURED_CHECK=1 DEFAULTLANGUAGENAME=DEU'
[12.07.2011 19:51:59.0410] [1] Removing MSI package with code '4934d1ea-be46-48b1-8847-f1af20e892c1'.
[12.07.2011 19:52:04.0551] [1] [ERROR] Unexpected Error
[12.07.2011 19:52:04.0551] [1] [ERROR] Couldn't remove product with code 4934d1ea-be46-48b1-8847-f1af20e892c1. Schwerwiegender Fehler bei der Installation. Error code is 1603.
[12.07.2011 19:52:04.0551] [1] [ERROR] Schwerwiegender Fehler bei der Installation
[12.07.2011 19:52:04.0613] [1] Ending processing uninstall-msipackage
The MSI package with code '4934d1ea-be46-48b1-8847-f1af20e892c1' ist the SP1.
Actual System: Server2008R2SP1 / Exchange2010SP1 RU3v3
It is possible to solve this problem?
Rene Hubert - Systemadministrator - DRK KH Lichtenstein gGmbH
I too have this
problem.

Exchange 2010 SP1 Upgrade to SP2 and SP3. Choose language.

Hello.
I going to install Exchange 2010 SP1 multilanguage and then update to SP2 and SP3
But then i download SP2 from Microsoft it's ask fоr choose language.
It ask about installer language or about Exchange language?
What language i need to choose if i have multilanguage Exchange SP1 installer?
And if i want to Exchange EMC be in English and Outlook on client machine shows Russian what language i need to choose when install first role from Exchange 2010 SP1 multilang DVD?

Exchange EMC language depends on OS version where you are running it.
Besides about client language you have to choose Russian language pack during install. More info below...
The language of the Outlook user interface that an Outlook user sees, including the content generated by Exchange, depends on the following:
The language the user is using in Outlook
Whether the language they're using in Outlook is supported by Exchange 2010
Whether the language they're using in Outlook has been configured to be available on the Exchange 2010 server
Consider the following scenarios:
When an Outlook user who's set their language to <Language A> signs in to their Exchange 2010 mailbox and both Outlook and Exchange 2010 support the language the user has specified, <Language A>, the user will see all messages and Exchange-generated
mailbox components, for example, the Inbox, in Language A.
When an Outlook user who's set their language to <Language A> signs in to their Exchange 2010 mailbox that's been set to <Language B>, the Outlook user will see the Outlook user interface in Language A, but will see the content generated
by Exchange. For example, by default, folder names such as Inbox,
Deleted Items, and Sent Items display in <Language B>.
You can change the Exchange mailbox language setting on the server using Exchange Management Console or the Exchange Management Shell. For information about how to use the Shell to change the language setting for a mailbox on a server, see
Set-MailboxRegionalConfiguration.
From: Client Language Support for Outlook -
http://technet.microsoft.com/en-us/library/dd638175%28v=exchg.141%29.aspx
Blog |
Get Your Exchange Powershell Tip of the Day from here

Owa working but outlook cant connecting to the new mailbox in Hosted exchange 2010 SP1

hi i recently join one organization they having Hosted Exchange 2010 Sp1 i created one new organization Unit and created
new MailBox but didnt give any permissions so when i try to connect to OWA then i log in and send and recive e-mails but when i try to connect to Outlook it say the name not found ...........
please help me

Hi sorry for so late respons i was on leaves .
new User not connected automatically getting the message "user name Not found " also when i try to connect manually the error message " there is problem with the security certificate. the name on the security certificate is invalid or does not match ..." also
Outlook some problem with some old Mailboxes
from Exerca i get the following errors i.e Certificate related
The Microsoft Connectivity Analyzer is attempting to test Autodiscover for [email protected].
Autodiscover was tested successfully.
Additional Details
Elapsed Time: 2927 ms.
Test Steps
Attempting each method of contacting the Autodiscover service.
The Autodiscover service was tested successfully.
Attempting to test potential Autodiscover URL https://xyz.co.uk/AutoDiscover/AutoDiscover.xml
Testing of this potential Autodiscover URL failed.
Additional Details
Elapsed Time: 417 ms.
Test Steps
Attempting to resolve the host name xyz.co.uk in DNS.
The host name resolved successfully.
Additional Details
Testing TCP port 443 on host xyz.co.uk to ensure it's listening and open.
The port was opened successfully.
Additional Details
Testing the SSL certificate to make sure it's valid.
The SSL certificate failed one or more certificate validation checks.
Additional Details
Test Steps
The Microsoft Connectivity Analyzer is attempting to obtain the SSL certificate from remote server xyz.co.uk on port 443.
The Microsoft Connectivity Analyzer successfully obtained the remote SSL certificate.
Additional Details
Validating the certificate name.
Certificate name validation failed.
Tell me more about this issue and how to resolve it
Additional Details
Attempting to test potential Autodiscover URL https://autodiscover.xyz.co.uk/AutoDiscover/AutoDiscover.xml
Testing of this potential Autodiscover URL failed.
Additional Details
Test Steps
Attempting to resolve the host name autodiscover.xyz.co.uk in DNS.
The host name resolved successfully.
Additional Details
Testing TCP port 443 on host autodiscover.xyz.co.uk to ensure it's listening and open.
The port was opened successfully.
Additional Details
Testing the SSL certificate to make sure it's valid.
The SSL certificate failed one or more certificate validation checks.
Additional Details
Elapsed Time: 270 ms.
Test Steps
The Microsoft Connectivity Analyzer is attempting to obtain the SSL certificate from remote server autodiscover.xyz.co.uk on port 443.
The Microsoft Connectivity Analyzer successfully obtained the remote SSL certificate.
Additional Details
Validating the certificate name.
Certificate name validation failed.
Tell me more about this issue and how to resolve it
Additional Details
Attempting to contact the Autodiscover service using the HTTP redirect method.
The Autodiscover service was successfully contacted using the HTTP redirect method.
.......................... Please help me how to resolve

Delete emails from a specific folder in Exchange 2010 SP1

Hi all,
Since Exchange 2010 SP1 does not have “-DeleteContent” parameter in mailboxexportrequest any more, how do we delete emails from a specific folder of a user mailbox? (Personal folder, not default folders).
Please note that the ASQ for searchquery in Search-Mailbox does not support “folder”.
If going for retention policy, is there a way to tag a retention policy to a specific folder of a user mailbox without user attention?
William Yang
William Yang

Hi William,
Yes, you may not run the Search-Mailbox to delete items in specific folder at the moment. Hope it will be back soon.
You can create a Personal tag, users can apply personal tags to folders they create. But users have to select related Retention Policy using Outlook or OWA manually.
For more information, please see:
Understanding Retention Tags and Retention Policies
http://technet.microsoft.com/en-us/library/dd297955.aspx
Frank Wang
Forum Support
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact
[email protected]

Upgrade From Exchange 2010 SP1 to SP3 - Schema Upgrade Question

Hello,
We're currently running Exchange 2010 SP1 in our environment and want to upgrade to SP3. I just had a couple of questions related to preparing AD for this new SP that I was hoping that someone could answer.
Setup
We have a single forest with two domains within it (A and B for example). The schema master is in Domain A but this domain doesn't contain any Exchange 2010 servers. Domain B contains our 2010 CAS and Mailbox servers.
Both domains have Windows 2003 SP2 domain controllers.
I understand that before I proceed with the upgrade to SP3, I first need to update the AD schema on our schema master. I was planning on doing the following :
Log onto an existing Windows 2008 R2 64 bit "member" server in domain A (containing the schema master) with an account which is a member of the Schema Admins and Enterprise Admins groups.
Run SETUP.EXE /PrepareAD.
Do I need to also run SETUP.EXE /PrepareDomain on domain A as well or does the /PrepareAD sort this out ?
I was then going to turn my attention to domain B (which contains the 2010 CAS and Mailbox servers) and do the following :
Log onto an existing Windows 2008 R2 64 bit 2010 Mailbox server with an account which is a member of the Domain Admins and Enterprise Admins groups.
Run SETUP.EXE /PrepareDomain
Is this the correct procedure to follow ? I assume that I can then go ahead and start to upgrade the Exchange 2010 SP1 servers in the following sequence :
CAS\HUB Server(s)
Mailbox Server(s).
Clarification on the AD upgrade steps would be appreciated.
Thanks
Mark

This has all the info you need:
http://technet.microsoft.com/en-us/library/bb125224(v=exchg.141).aspx
Prepare Active Directory and Domains
and
http://technet.microsoft.com/en-us/library/bb629560(v=exchg.141).aspx
Upgrade Exchange 2010 to Exchange 2010 SP1, Exchange 2010 SP2, or Exchange 2010 SP3
Note: There is no harm in simply running setup/PrepareAllDomains.
You should break out each Prep step since you have multiple domains:
setup/PrepareSchema
setup /PrepareAD
setup /PrepareAllDomains
you can run all of these from the same DC you run the setup/PrepareSchema step!
Twitter!:
Please Note: My Posts are provided “AS IS” without warranty of any kind, either expressed or implied.

Exchange 2010 SP1 Update Rollup 6 to Exchange 2010 SP3

Hi there,
I am planning to install Exchange 2010 SP3 next week and after reading some of the related comments on this site I got a little worried.
Our current Exchange environment consists of the following:
1 x CAS/HT Server
2 x Mailbox Server (members of a DAG)
The OS of the 3 servers is Windows Server 2008 R2 SP1. All servers are running Exchange 2010 SP1 Update Rollup 6.
The Execution Policies on our Exchange servers are set as follows:
– CAS/HT Server:
Scope ExecutionPolicy
MachinePolicy Undefined
UserPolicy Undefined
Process Undefined
CurrentUser Undefined
LocalMachine Unrestricted
– Mailbox Servers:
Scope ExecutionPolicy
MachinePolicy Undefined
UserPolicy Undefined
Process Undefined
CurrentUser Undefined
LocalMachine RemoteSigned
Please note that we do not have any Group Policies that defined the PowerShell script execution policy.
I would be very grateful if you (or any of the kind readers) could help me with following questions:
1- Do I have to change the execution policy on our Exchange servers before installing SP3? If I have to change a policy, what should I change? And how would you recommend I should do this?
2- After installing SP3 on a server, can I install the latest rollup update on this server before moving to the next server? For example, can I do the following:
i. Install SP3 followed by RU 5 on the CAS/HT server -> Apply the our custom settings
ii. Install SP3 followed by RU 5 on the first mailbox server
iii. Install SP3 followed by RU 5 on the second mailbox server
Many thanks,
M

Hi Amit,
Many thanks for the swift reply.
That's correct. We didn't set the Powershell execution policy via Group Policy. We only configured the execution policy of "LocalMachine" to "Unrestricted" on the CAS/HT server using the "Set-ExecutionPolicy" command on the server.
The mailbox servers' execution policies have not been changed and are set to those values by default.
I must admit, I go event more confused when I read the "http://support.microsoft.com/kb/2668686" and "http://support.microsoft.com/kb/2810617" articles.
But it looks like I shouldn't worry as our current Powershell execution policies shouldn't affect the upgrade. Right?

Exchange 2010 sp3 rollup 7 fails

Exchange 2010 sp3 rollup 7 fails. This is ran at an elevated prompt and the UAC off. This server is also logged in as the domain Administrator account.
The server currently has rollup 4 SP3 installed. I'm wondering if I should uninstall it, reboot then try the Rollup 7 SP3 update?

Hi,
Can you please post the error?
At the same time please check these.
http://technet.microsoft.com/en-us/library/ee861125(v=exchg.141).aspx
http://exchangeserverpro.com/how-to-install-updates-on-exchange-server-2010-database-availability-groups/
Thanks, MAS
Please mark as helpful if you find my comment helpful or as an answer if it does answer your question. That will encourage me - and others - to take time out to help you.

Exchange 2010 SP1 - Export to PST, Remove Mailbox

I'm looking for a PowerShell script that will allow me to use Exchange 2010 SP1 to export a mailbox to PST and then when finished, delete the user and mailbox. I typically do this process manually about 6 months after an employee leaves the company (allowing
for live access to the mailbox and message forwarding to their supervisor).
Ideally, the script would take input for a mailbox ID, and then export the file to a file of the mailbox name (Prompt: jdoe -> New-MailboxExportRequest -Mailbox jdoe -FilePath \\server\path\jdoe.pst). After the export is complete, it would schedule the
mailbox for complete removal and remove the completed mailbox export request. The prompt and export process should be simple enough, but I suspect the difficulty will come with monitoring for the completed request before acting on the removal.
Thanks for any help provided! :)

Thanks for the guidance!
I think I was able to come up with something that will do the trick nicely:
$Name = Read-Host "Please enter a mailbox to archive"
New-MailboxExportRequest -Mailbox $Name -FilePath \\Exchange\C$\ExchangeExports\$Name.pst
while ((Get-MailboxExportRequest -Mailbox $Name | Where {$_.Status -eq "Queued" -or $_.Status -eq "InProgress"}))
sleep 60
Get-MailboxExportRequest -Mailbox $Name | Remove-MailboxExportRequest -Confirm:$false
Remove-Mailbox -Identity $Name -Confirm:$false
Hopefully it may help others.

Exchange 2010 SP1 Installtion failed

I tried to install exchange 2010 on one of our child domain (windows server 2003 SP2) and i succes to make a DCPROMO and the prerequest check finish succesfully after 2.5 houre then when try to install i have recieved our that setup failed to reconnect
the root dc with below errot and replication and DNS and every this is working well with root and local domain contrroler
Organization Preparation
Failed
Error:
The following error was generated when "$error.Clear();
initialize-ExchangeUniversalGroups -DomainController $RoleDomainController -ActiveDirectorySplitPermissions $RoleActiveDirectorySplitPermissions
" was run: "Failed to reconnect to Active Directory server -root-dc-02.. Make sure the server is available, and that you have used the correct credentials.".
Failed to reconnect to Active Directory server root-dc-02.. Make sure the server is available, and that you have used the correct credentials.
Active Directory server root-dc-02. is not available. Please retry at a later time.
Click here for help...
http://technet.microsoft.com/en-US/library/ms.exch.err.default(EXCHG.141).aspx?v=14.1.218.11&e=ms.exch.err.Ex88D115&l=0&cl=cp
Elapsed
Preparing Setup
Cancelled
Stopping Services
Cancelled
Copy Exchange Files
Cancelled
Language Files
Cancelled
Restoring services
Cancelled
Languages
Cancelled
Management Tools
Cancelled
Hub Transport Role
Cancelled

Hi fadi,
any updates for your issur?
Thanks,
Jeff
如果您对我们的论坛在线支持服务有任何的意见或建议，请通过邮件告诉我们。
立刻免费下载
TechNet
论坛好帮手

Exchange 2013 SP1 readiness check failing

Trying to install our first Exchange 2013 SP1 server on Windows 2012 R2 in our datacentre, the readiness check fails with:
Error:
The Active Directory schema isn't up-to-date, and this user account isn't a member of the 'Schema Admins' and/or 'Enterprise Admins' groups.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.SchemaUpdateRequired.aspx
There are many more errors relating to Enterprise admin rights etc.
Please note that:
My account is Domain admin, Schema admin and Enterprise admin member, it always has been.
I tried the built-in AD Administrator which of course is part of the groups as well, no difference.
Active Directory is at 2008 R2 for domain and forest functional levels.
I tried rejoining the new Exchange designated server to the domain
I've installed RSAT-ADDS, the Managed API 4.0 and all the other windows roles via powershell
There is a local domain controller that is a global catalog server on the new Exchange server subnet
I tried running the Exchange Setup on a different server on the same subnet as where the active 2010 Exchange server resides as well as the FSMO AD role holder resides, this works fine. I even did the AD prep from there no problem, that made no difference
on the datacentre server
AD replicates fine between the FSMO role holder and the Datacentre (no errors in dcdiag or repadmin /showrepl)
This error is in the event log:
The description for Event ID 4027 from source MSExchange ADAccess cannot be found. Either the component that raises this event is not installed on your local computer or the installation is corrupted. You can install or repair the component on the local computer.
If the event originated on another computer, the display information had to be saved with the event.
The following information was included with the event:
ExSetupUI.exe
6724
Get Servers for domain.local
TopologyClientTcpEndpoint (localhost)
3
System.ServiceModel.EndpointNotFoundException: Could not connect to net.tcp://localhost:890/Microsoft.Exchange.Directory.TopologyService. The connection attempt lasted for a time span of 00:00:02.0475315. TCP error code 10061: No connection could be made because the target machine actively refused it 127.0.0.1:890. ---> System.Net.Sockets.SocketException: No connection could be made because the target machine actively refused it 127.0.0.1:890
at System.Net.Sockets.Socket.DoConnect(EndPoint endPointSnapshot, SocketAddress socketAddress)
at System.Net.Sockets.Socket.Connect(EndPoint remoteEP)
at System.ServiceModel.Channels.SocketConnectionInitiator.Connect(Uri uri, TimeSpan timeout)
--- End of inner exception stack trace ---
Server stack trace:
at System.ServiceModel.Channels.SocketConnectionInitiator.Connect(Uri uri, TimeSpan timeout)
at System.ServiceModel.Channels.BufferedConnectionInitiator.Connect(Uri uri, TimeSpan timeout)
at System.ServiceModel.Channels.ConnectionPoolHelper.EstablishConnection(TimeSpan timeout)
at System.ServiceModel.Channels.ClientFramingDuplexSessionChannel.OnOpen(TimeSpan timeout)
at System.ServiceModel.Channels.CommunicationObject.Open(TimeSpan timeout)
at System.ServiceModel.Channels.ServiceChannel.OnOpen(TimeSpan timeout)
at System.ServiceModel.Channels.CommunicationObject.Open(TimeSpan timeout)
Exception rethrown at [0]:
at System.Runtime.Remoting.Proxies.RealProxy.HandleReturnMessage(IMessage reqMsg, IMessage retMsg)
at System.Runtime.Remoting.Proxies.RealProxy.PrivateInvoke(MessageData& msgData, Int32 type)
at System.ServiceModel.ICommunicationObject.Open()
at Microsoft.Exchange.Net.ServiceProxyPool`1.GetClient(Boolean useCache)
at Microsoft.Exchange.Net.ServiceProxyPool`1.TryCallServiceWithRetry(Action`1 action, String debugMessage, WCFConnectionStateTuple proxyToUse, Int32 numberOfRetries, Boolean doNotReturnProxyOnSuccess, Exception& exception)
the message resource is present but the message is not found in the string/message table

So I decided to re-install the OS, worked perfectly now. Only difference from before would be:
SCCM hasn't pushed SCEP 2012 to the new build of the same server yet
The original server was installed in a different AD site and then it was physically mode and reassigned to an new AD site and subnet
I might have installed the pre-reqs in a slightly different order (RSAT-ADDS, all the IIS etc things via powershell
and then the UCM API 4.0. (saw few comments that the order of how you install them matters in other forums).
10 or so Microsoft Windows updates haven't installed on the new OS build yet.
Other than that, its identical. But if its not broken don't fix it, perhaps the above can help someone else though.

Exchange 2010 - WS-Management Service does not support

Hi,
We have a tool which was used for bulk Mailbox creation, Mailbox Movement etc. This we have used in Exchange 2007 also and was working fine. Now in Exchange 2010 we are facing some issues. Tool is written in VB.
Exchange 2010 SP2 is running in all servers and we have 2 Mailbox Servers in DAG and 2 HUBCAS in CAS Array/NLB.
When Team is trying to fetch the DB details in exchange 2010 through tool they are not able to connect and getting error as
"Connecting to remote Server failed with the following error message. The WS-Management Service does not support the request."
I have checked everything from Exchange like Remorepowersell status, WinRM, WS Managemet dll location and entry in config file everthing seems to be fine.
I checked through EMTShooter tool also and no issues reported and connection was success through EMTShooter.
Pls suggest if anymore we can check to fix the problem.
Note: everything is working frine from Powershell and Exchange Management console.
Regards:Mahesh

Hi
Yes, i got it confirmed and coding team claims that no issue with code and its working in some other setup.
<v:shapetype coordsize="21600,21600" filled="f" id="_x0000_t75" o:preferrelative="t" o:spt="75" path="m@4@5l@4@11@9@11@9@5xe" stroked="f"><v:stroke joinstyle="miter"><v:formulas><v:f
eqn="if lineDrawn pixelLineWidth 0"><v:f eqn="sum @0 1 0"><v:f eqn="sum 0 0 @1"><v:f eqn="prod @2 1 2"><v:f eqn="prod @3 21600 pixelWidth"><v:f eqn="prod @3 21600 pixelHeight"><v:f eqn="sum @0 0 1"><v:f eqn="prod @6 1 2"><v:f eqn="prod @7 21600 pixelWidth">Below
is the snapshot of error with coding <v:f eqn="sum @8 21600 0">
<v:f eqn="prod @7 21600 pixelHeight">
<v:f eqn="sum @10 21600 0">
</v:f></v:f></v:f></v:f></v:f></v:f></v:f></v:f></v:f></v:f></v:f></v:f></v:formulas>
<v:path gradientshapeok="t" o:connecttype="rect" o:extrusionok="f">
<o:lock aspectratio="t" v:ext="edit">
</o:lock></v:path></v:stroke></v:shapetype><v:shape alt="" id="Picture_x0020_2" o:spid="_x0000_i1025" style="width:631.5pt;height:148.5pt;" type="#_x0000_t75">
<v:imagedata o:href="cid:[email protected]" src="file:///C:\Users\aralele\AppData\Local\Temp\msohtmlclip1\01\clip_image001.jpg">
</v:imagedata></v:shape>
Regards:Mahesh

Upgrading to Exchange 2010 SP1

When I'm upgrading Exchange 2010 to SP1, I get to tthe Hub Transport Role and it errors out with the following messsage:
Summary: 8 item(s). 3 succeeded, 1 failed.
Elapsed time: 00:08:15
Language Files
Completed
Elapsed Time: 00:04:40
Restoring services
Completed
Elapsed Time: 00:00:01
Languages
Completed
Elapsed Time: 00:02:59
Hub Transport Role
Failed
Error:
The following error was generated when "$error.Clear();
          if ( ($server -eq $null) -and ($RoleIsDatacenter -ne $true) )
            Update-RmsSharedIdentity -ServerName $RoleNetBIOSName
        " was run: "There should only be a single RMS Shared Identity user. Found CN=FederatedEmail.4c1f4d8b-8179-4148-93bf-00a95fa1e042,CN=Users,DC=corporate,DC=internal and CN=FederatedEmail.4c1f4d8b-8179-4148-93bf-00a95fa1e042,OU=migrate,DC=corporate,DC=internal.".
There should only be a single RMS Shared Identity user. Found CN=FederatedEmail.4c1f4d8b-8179-4148-93bf-00a95fa1e042,CN=Users,DC=corporate,DC=internal and CN=FederatedEmail.4c1f4d8b-8179-4148-93bf-00a95fa1e042,OU=migrate,DC=corporate,DC=internal.
Click here for help...
http://technet.microsoft.com/en-US/library/ms.exch.err.default(EXCHG.141).aspx?v=14.1.218.11&e=ms.exch.err.Ex88D115&l=0&cl=cp
Elapsed Time: 00:00:34
Client Access Role
Cancelled
Mailbox Role
Cancelled
Management Tools
Cancelled
Finalizing Setup
Cancelled
I haven't been able to find anything on the web regarding this error, so any help would be appreciated. We used to ADMT to migrate users into a new domain, but what it looks like to me (and I'm sure I'm wrong) is that the same user is set up in migrate
OUT as the regular Users Container.
What am I missing???
Thanks in advance.
Jeff

Hi,
Please try to use ADSIedit to check if you have two federated email account. You may need to delete the double one.
Remove the FederatedEmail.4c1f4d8b-8179-4148-93bf-00a95fa1e042 e-mail account by using the ADSIEDIT tool. To do this, follow these steps:
Click Start, click Run, type adsiedit.msc, and then click
OK.
Locate the Default Naming Context node, and then locate to the
CN=Users container.
Locate and then right-click the CN=FederatedEmail.4c1f4d8b-8179-4148-93bf-00a95fa1e042 container. Then, click
Delete.
If that is not help, then I recommend y ou to remove all those two federatedemail account and then create a new one.
Rerun the Exchange Server 2010 Mailbox role setup application.
Create a new federated e-mail account by using the following command:
New-Mailbox -Arbitration -Name FederatedEmail.4c1f4d8b-8179-4148-93bf-00a95fa1e042 -UserPrincipalName FederatedEmail.4c1f4d8b-8179-4148-93bf-00a95fa1e042@<Default_Accepted_Domain>
Regards,
Xiu

Exchange 2010 SP1 management console fail

Similar Messages

Maybe you are looking for