Exchange 2010 SP3 install

Hi,
I am running with Exchange 2010 SP1 in DAG & CAS/HUB in cluster mode. need to upgrade to SP3. few things need to know
1. Schema upgrade will be done I as read in the article. can this create any issue? what is the best measure to safeguard any problems of schema upgrade. Do we do this along with exchange setup or we should run schema upgrade prior to install exchange 2010
SP3?
2. Any impact on active sync, outlook anywhere & HUB connectors side post SP3?
3. Do we need to take any exchange related backups as we are running mailbox, CAS/HUB servers in redundant mode?
Please share your experiences.
Regards,
VIpin

Hello,
1. It is a good practice to run schema updates before launching Exchange update. You should also make backups of your domain controllers before any schema updates because these
particular changes cannot be rolled back easily.
3. Yes, you should have backups (tested!) of your Exchange servers. Server's redundancy (DAG's, CAS Arrays etc) doesn't protect your servers if the update fails.
Hope it helps,
Adam
www.codetwo.com
If this post helps resolve your issue, please click the "Mark as Answer" or "Helpful" button at the top of this message. By marking a post as Answered, or Helpful you help others
find the answer faster.

Similar Messages

Exchange 2010 SP3 install question

Greetings! I am planning on installing the SP3 update for Exchange 2010 in preparation for a Hybrid deployment with O365. After installing the SP3 update to all Exchange servers in our environment, I was going to then install the RU8 on the servers.
Hopefully I can perform all of this during one maintenance window. I have already performed the schema update for SP3 during our most recent maintenance window.
I have been scouring the forums for any potential upgrade issues. I wanted to know if there was any concern about the RU8 update for SP3 that might affect our environment from past experience of other admins; whether it be Outlook clients (we use mostly
Outlook 2010 with some Outlook 2013) or OWA. We are currently on SP2, RU6.
Thanks in advance!

Hi,
As what Amit mentioned above, you can upgrade from Exchange 2010 SP2 RU6 to SP3 RU8, as long as this version is supported for Hybrid deployment with O365.
http://technet.microsoft.com/en-us/library/bb629560(v=exchg.141).aspx
To DAGs, please consider the following conditions:
Upgrade passive servers first. Place server in maintenance mode if any monitoring applications are in use. Stop any scheduled tasks or other processes running on the DAG member or within that DAG that could adversely affected the DAG member being upgraded
or the upgrade process.
Best regards,
If you have feedback for TechNet Subscriber Support, contact
[email protected]
Belinda Ma
TechNet Community Support

Exchange 2010 SP3 install failure

While attempting to update my first CAS to SP3 from SP2 I am getting the following error.
The install appears to be looking for a RBAC security group called "Help Desk". To my knowledge, such a group never existed on our domain. Is there a way to create this group with the correct GUID so that the install will work?
Is there another method to repair this group?
Summary: 14 item(s). 0 succeeded, 1 failed.
Elapsed time: 00:00:45
Organization Preparation
Failed
Error:
The following error was generated when "$error.Clear();
initialize-ExchangeUniversalGroups -DomainController $RoleDomainController -ActiveDirectorySplitPermissions $RoleActiveDirectorySplitPermissions
" was run: "The well-known object entry B:32:B3DDC6BE2A3BE84B97EB2DCE9477E389:CN=Help Desk\0ADEL:baf7b856-5913-4db8-8f8d-8e54085921b5,CN=Deleted Objects,DC=DOMAIN,DC=local on the otherWellKnownObjects attribute in the container object CN=Microsoft
Exchange,CN=Services,CN=Configuration,DC=DOMAIN,DC=local points to an invalid DN or a deleted object. Remove the entry, and then rerun the task.".
The well-known object entry B:32:B3DDC6BE2A3BE84B97EB2DCE9477E389:CN=Help Desk\0ADEL:baf7b856-5913-4db8-8f8d-8e54085921b5,CN=Deleted Objects,DC=DOMAIN,DC=local on the otherWellKnownObjects attribute in the container object CN=Microsoft Exchange,CN=Services,CN=Configuration,DC=DOMAIN,DC=local
points to an invalid DN or a deleted object. Remove the entry, and then rerun the task.
Click here for help...
http://technet.microsoft.com/en-US/library/ms.exch.err.default(EXCHG.141).aspx?v=14.3.123.3&e=ms.exch.err.Ex88D115&l=0&cl=cp
Elapsed Time: 00:00:45
Preparing Setup
Cancelled
Stopping Services
Cancelled
Languages
Cancelled
Remove Exchange Files
Cancelled
Preparing Files
Cancelled
Copy Exchange Files
Cancelled
Language Files
Cancelled
Restoring services
Cancelled
Languages
Cancelled
Hub Transport Role
Cancelled
Client Access Role
Cancelled
Management Tools
Cancelled
Finalizing Setup
Cancelled

Help Desk is a universal Microsoft Exchange Security Group created when you run Setup.com /PrepareAD:
If it was deleted you need to restore it.
Do you have AD recycle bin? maybe you can restore it from there. otherwise a restore of that group will be needed:
http://technet.microsoft.com/en-us/library/dd379509(v=ws.10)
There is another way of deleting all Exchange Security Group and recreate them, but I'm not sure its supported method (if you choose - do it on your own risk):
http://careexchange.in/how-to-recreate-corrupted-microsoft-security-groups-in-exchange-2010/
http://www.itguydiaries.net/2012/07/omg-exchange-security-groups-were.html
Please take a moment to Vote as Helpful and/or Mark as Answer where applicable. Thanks.

Exchange 2010 SP3 Install Issue

Got all of our servers updated to SP3 RU 4 but have 1 box not working. It's our second Cas box in our main location
I have tried multiple times and i keep getting the following error, not sure how to get past this one.:
Hub Transport Role
Failed
Error:
The following error was generated when "$error.Clear();
if ( ($server -eq $null) -and ($RoleIsDatacenter -ne $true) )
Update-RmsSharedIdentity -ServerName $RoleNetBIOSName
" was run: "Host name 'LZBEXCH02' matches more than one computer: 'CN=LZBEXCH02,OU=Exchange Servers,OU=WSUS No Reboot,OU=Servers,OU=Monroe,OU=Data Centers,DC=na,DC=lzb,DC=hq' and 'CN=LZBEXCH02,CN=Computers,DC=lzb,DC=hq'.".
Host name 'LZBEXCH02' matches more than one computer: 'CN=LZBEXCH02,OU=Exchange Servers,OU=WSUS No Reboot,OU=Servers,OU=Monroe,OU=Data Centers,DC=na,DC=lzb,DC=hq' and 'CN=LZBEXCH02,CN=Computers,DC=lzb,DC=hq'.
Click here for help... http://technet.microsoft.com/en-US/library/ms.exch.err.default(EXCHG.141).aspx?v=14.3.123.3&e=ms.exch.err.Ex88D115&l=0&cl=cp
Elapsed Time: 00:00:31
Client Access Role
Cancelled
Management Tools
Cancelled
Finalizing Setup
Cancelled
Jessica Cochran

Did you checked
CN=LZBEXCH02,OU=Exchange Servers,OU=WSUS No Reboot,OU=Servers,OU=Monroe,OU=Data Centers,DC=na,DC=lzb,DC=hq'
And
'CN=LZBEXCH02,CN=Computers,DC=lzb,DC=hq'
Seems you have duplicate objects

Install Exchange 2010 Sp3 on Windows 2012 R2

Dear All,
From Microsoft Exchange support matrix, I can tell that Exchange 2010 Sp3 is not listed on supported page. However when I run the setup, the prerequisite setup check, dose not list any warnings or issues with the setup, all check are green. Is it possible
that the support OS matrix has not been updated? Is Exchange 2010 Sp3 supported on Windows 2012 R2?
http://blogs.technet.com/b/rmilne/archive/2013/09/17/exchange-support-for-windows-server-2012-r2.aspx
Thank you

The prerequisite check is checking that the required Windows components are installed. Exchange 2010 is still not supported on Windows Server 2012 R2.

Is WMF3 or WMF4 supported in Exchange 2010 SP3 UR5 installed on Server 2008 R2 SP1?

We'd like to upgrade WMF (aka powershell) on our Exchange 2010 servers but I haven't been able to find any updated information on support with the most recent servicepack/update rollup.
Is installing WMF3 or WMF4 supported on Server 2008 R2 SP1 w/ Exchange 2010 SP3 UR5?

WindowsPowerShell 3.0 is supported. Haven't seen 4.0 running for exchange 2010 on 2008 R2
http://blogs.technet.com/b/heyscriptingguy/archive/2013/11/30/weekend-scripter-wmf-powershell-and-exchange-server-compatibility.aspx
http://blog.crayon.no/blogs/janegil/archive/2013/11/17/how_2D00_to_2D00_install_2D00_windows_2D00_powershell_2D00_4_2D00_0.aspx
Cheers,
Gulab Prasad
Technology Consultant
Blog:
http://www.exchangeranger.com    Twitter:
  LinkedIn:
   Check out CodeTwo’s tools for Exchange admins
Note: Posts are provided “AS IS” without warranty of any kind, either expressed or implied, including but not limited to the implied warranties of merchantability and/or fitness for a particular purpose.
Gulab,
Where did you read that WMF3 is supported on Exchange 2010 SP3 on Server 2008 R2?
Neither of the links you pasted suggest that and in fact explicitly say "There has been no testing with ExchangeServer 2010 SP3 and WMF 3.0 installed on Windows Server 2008 R2."
My Bad, that was TYPO...
Cheers,
Gulab Prasad
Technology Consultant
Blog:
http://www.exchangeranger.com    Twitter:
  LinkedIn:
   Check out CodeTwo’s tools for Exchange admins
Note: Posts are provided “AS IS” without warranty of any kind, either expressed or implied, including but not limited to the implied warranties of merchantability and/or fitness for a particular purpose.

Problems with OWA after installing Exchange 2010 SP3

Hi,
I just installed Exchange 2010 SP3 on a SBS 2011 machine. The installation completed successfully, but after the installation OWA isn't working anymore. When I browse to OWA I get the following message:
I did a reset for the OWA vritual directory, but nothing helps..
Stack Trace:
[NullReferenceException: Object reference not set to an instance of an object.]
Microsoft.Exchange.Clients.Owa.Core.Logon..ctor() +28
ASP.auth_logon_aspx..ctor() +17
__ASP.FastObjectFactory_app_web_9ficbu1h.Create_ASP_auth_logon_aspx() +30
System.Web.Compilation.BuildManager.CreateInstanceFromVirtualPath(VirtualPath virtualPath, Type requiredBaseType, HttpContext context, Boolean allowCrossApp, Boolean noAssert) +137
System.Web.UI.PageHandlerFactory.GetHandlerHelper(HttpContext context, String requestType, VirtualPath virtualPath, String physicalPath) +49
System.Web.MaterializeHandlerExecutionStep.System.Web.HttpApplication.IExecutionStep.Execute() +424
System.Web.HttpApplication.ExecuteStep(IExecutionStep step, Boolean& completedSynchronously) +262

Hi Alelieveld,
When you reset a virtual directory, the virtual directory is removed and a new virtual directory with default settings is created.
After you reset the VD, did you restart IIS?
For more information, please see:
Reset Client Access Virtual Directories
http://technet.microsoft.com/en-us/library/ff629372(v=exchg.141).aspx
Frank Wang
TechNet Community Support

Unable to install rollup4 for Exchange 2010 SP3

Hi,
I'm unable to install KB2905616 on my multi-role Exchange 2010 SP3 server. The setup wizard gets stuck at "the setup wizard is generating native images for .NET assemblies........"
I know that this process will take some time to complete but I have waited 10 hours.
I've tried to reboot the server and restart the setup.
Exchange is functioning perfectly otherwise.
Any help would be greatly appreciated :)
/Søren Emig

Hi,
I recommend you check if the anti-virus has been disabled before you start the upgrade process.
If you didn't ,the update could fail or take an extended amount of time.
Also, disable all other third-party apps/plugins that might be installed (like backup agents).
In addition,the following articles for your reference:
Install the Latest Update Rollup for Exchange 2010
When you install an update rollup package, Exchange tries to connect to the certificate revocation list (CRL) Web site. Exchange examines the CRL list to verify the code signing certificate. (To download and view the CRL list, see
CodeSignPCA.crl.) If Exchange can't connect to the CRL Web site, the following symptoms may occur:
The installation takes a long time to complete.
You receive the following message during the installation: Creating native images for .Net assemblies
When Exchange isn't connected to the Internet, each CRL request must complete before the installation can continue.
To work around this issue and to reduce installation times, turn off the
Check for publisher’s certificate revocation option on the server that is being upgraded. Use the following steps:
Start Internet Explorer.
On the Tools menu, click Internet Options.
Click the Advanced tab, and then locate the Security section.
Clear the Check for publisher’s certificate revocation check box, and then click
OK.
After the update rollup installation is complete, select the Check for publisher’s certificate revocation option.
Generating NGEN images takes longer than expected
Hope this helps!
Thanks.
Niko Cheng
TechNet Community Support

Exchange 2010 SP3 and UR6 Query - Order of Install

hi,
I need to update my Exchange 2010 SP2 Servers to SP3 and Update Rollup 6.
Can someone confirm the update order for me?
I have 5 servers;
Live Data Centre:
2 x HUB / CAB (Using Windows NLB)
2 x Mailbox (DAG)
Disaster Recovery:
1 x Multi-Role Server (CAS / HUB and Mailbox) - this is also Part of the DAG
Two Questions:
1.) What is the Order in which I install SP3 on these Servers? Should it be Live Data Centre: HUB / CAS, Mailbox Servers and THEN the Multi-Role Server at DR?
2.) When Upgrading each server, should I do SP3, reboot, check and THEN install Update Rollup 6 - or should I upgrade all Servers to SP3 and then start the process again to get to Update Rollup 6?
Thanks in advance for your help with this query.
Regards,
Adam

1) Internet facing CAS first in each AD site. Order: CAS> HUB> UM> MBX
2) Personally, I would install SP3, reboot, then install SP6, but its really up to you.
http://technet.microsoft.com/en-us/library/bb629560(v=exchg.141).aspx
Upgrade Exchange 2010 to Exchange 2010 SP1, Exchange 2010 SP2, or Exchange 2010 SP3
Twitter!: Please Note: My Posts are provided “AS IS” without warranty of any kind, either expressed or implied.

How do I know which update rollup is installed on my exchange 2010 sp3 server ?

how do I know which update rollup version is installed on my exchange 2010 sp3 server ?
Anand_N

And take a peek here:
http://blogs.technet.com/b/rmilne/archive/2013/10/29/how-to-check-exchange-2010-ru-version.aspx
Cheers,
Rhoderick
Microsoft Senior Exchange PFE
Blog:
http://blogs.technet.com/rmilne
Twitter:   LinkedIn:
  Facebook:
  XING:
Note: Posts are provided “AS IS” without warranty of any kind, either expressed or implied, including but not limited to the implied warranties of merchantability and/or fitness for a particular purpose.

[SOLVED] Can't add a node to the cluster with error (Exchange 2010 SP3 DAG Windows Server 2012)

Hi there!
I have a problem which makes me very angry already :)
I have two servers Exchange 2010 SP3 with MB role started on Windows Server 2012. I decided to create a DAG.
I have created the prestaged AD object for the cluster called msc-co-exc-01c, assigned necessary permissions and disabled it. Allowed through the Windows Firewall traffic between nodes and prepared the File Share Witness server.
Then I have tried to add nodes. The first node has been added successfully, but the second node doesn't want to be added :). Now I can add only one node to the DAG. I tried to add different servers first, but only the first one was added.
LOGS on the second nodes:
Application Log
"Failed to initialize cluster with error 0x80004005." (MSExchangeIS)
Failover Clustering Diagnostic Log
"[VER] Could not read version data from database for node msc-co-exc-04v (id 1)."
CMDLET Error:
Summary: 1 item(s). 0 succeeded, 1 failed.
Elapsed time: 00:06:21
MSC-CO-EXC-02V
Failed
Error:
A database availability group administrative operation failed. Error: The operation failed. CreateCluster errors may result from incorrectly configured static addresses. Error: An error occurred while attempting a cluster operation. Error: Cluster API '"AddClusterNode()
(MaxPercentage=100) failed with 0x5b4. Error: This operation returned because the timeout period expired"' failed. [Server: msc-co-exc-04v.int.krls.ru]
An Active Manager operation failed. Error An error occurred while attempting a cluster operation. Error: Cluster API '"AddClusterNode() (MaxPercentage=100) failed with 0x5b4. Error: This operation returned because the timeout period expired"' failed..
This operation returned because the timeout period expired
Click here for help... http://technet.microsoft.com/en-US/library/ms.exch.err.default(EXCHG.141).aspx?v=14.3.174.1&t=exchgf1&e=ms.exch.err.ExC9C315
Warning:
Network name 'msc-co-exc-01c' is not online. Please check that the IP address configuration for the database availability group is correct.
Warning:
The operation wasn't successful because an error was encountered. You may find more details in log file "C:\ExchangeSetupLogs\DagTasks\dagtask_2014-11-17_13-54-56.543_add-databaseavailabiltygroupserver.log".
Exchange Management Shell command attempted:
Add-DatabaseAvailabilityGroupServer -MailboxServer 'MSC-CO-EXC-02V' -Identity 'msc-co-exc-01c'
Elapsed Time: 00:06:21
UPD:
when Exchange servers ran on the same Hyper-V node, the DAG is working well, but if I move one of VM to another node, It stops working.
I have installed Wireshark and captured trafic of cluster interface. When DAG members on the same HV-node, there is inbound and outbound traffic on the cluster interface, but if I move one of DAG member to another node, in Wireshark I see only outbound traffic
on both nodes.
It's confused me, because there is normal connectivity between these DAG members through the main interface.
Please, help me if you can.

Hi, Jared! Thank you for the reply.
Of course I did it already :) I have new info:
when Exchange servers ran on the same Hyper-V node, the DAG is working well, but if I move one of VM to another node, It stops working.
I have installed Wireshark and captured trafic of cluster interface. When DAG members on the same HV-node, there is inbound and outbound traffic on the cluster interface, but if I move one of DAG member to another node, in Wireshark I see only outbound traffic
on both nodes.
It's confused me, because there is normal connectivity between these DAG members through the main interface.

Exchange 2010 SP3 - Can DAG member be on OS 2012 R2 STD?

Hi guys.
We have Exchange 2010 SP3 on 2008 r2 enterprise.
now we are thinking about having DAG. I know that recommendations is to have the same OS on 2nd Exchange server but still is it possible to make DAG between: Exchange 2010 SP3 on 2008 r2 enterprise and on other side Exchange 2010 SP3 on 2012 R2 STD?
with best regards,
bostjanc

Hi guys.
We have Exchange 2010 SP3 on 2008 r2 enterprise.
now we are thinking about having DAG. I know that recommendations is to have the same OS on 2nd Exchange server but still is it possible to make DAG between: Exchange 2010 SP3 on 2008 r2 enterprise and on other side Exchange 2010 SP3 on 2012 R2 STD?
with best regards,
bostjanc
No. It wont let you do that.
http://technet.microsoft.com/en-us/library/dd638104(v=exchg.141).aspx
DAGs are available in both Exchange 2010 Standard Edition and Exchange 2010 Enterprise Edition. In addition, a DAG can contain a mix of servers running Exchange 2010 Standard Edition and Exchange 2010 Enterprise Edition.
Each member of the DAG must also be running the same operating system. Exchange 2010 is supported on both the Windows Server 2008 and Windows Server 2008 R2 operating systems. All members of a DAG must run either Windows Server 2008 or Windows Server 2008
R2. They can't contain a combination of both Windows Server 2008 and Windows Server 2008 R2.
In addition to meeting the prerequisites for installing Exchange 2010, there are operating system requirements that must be met. DAGs use Windows Failover Clustering technology, and as a result, they require the Enterprise version of Windows.
Twitter!: Please Note: My Posts are provided “AS IS” without warranty of any kind, either expressed or implied.

SME 7.1 not working with Exchange 2010 SP3 UR8v2 and OnTap 8.2.3 7mode

Followed IMT and installed software that NetApp said would work.Ontap 8.2.3 7-modevmWare 5.0 SP3Microsoft Windows Server 2008 R2 SP1Exchange 2010 SP3 UR8v2NetApp Host Tools 6.0.2SnapDrive 7.1.1SME 7.1 Everything connects fine. SnapDrive sees my drives. SME connects to Exchange Server. However in the process of configuring SME, I get the following error. I have followed knowledge base article and increased the timeout of DFM connection in registry, but that has not solved the problem. Has anyone run into this before? SME 6.1 works fine, but is not compatible with SnapDrive 7.1.1 (causes verifications to fail because server can't mount clone) and lower SnapDrive versions are not compatible with Ontap 8.2.3. I am in a real bind here. Thanks in advance.

the following configuration for SME 7.1 is no longer supported: Windows Server 2008 R2Exchange 2010 SP3 RU1 – RU5WMF/PowerShell 3.0SME 7.1 The supported configuration will now be: Windows Server 2008 R2Exchange 2010 SP3 RU5WMF/PowerShell 4.0SME 7.1 this is because Microsoft does not support WMF 3.0 on Server 2008 R2 running Exchange 2010 SP3, with any RU version.SME 7.1 requires a minimum of PowerShell 3.0 (part of WMF 3.0) in order to run. Feel free to review the Exchange Server Supportability Matrix located here: https://technet.microsoft.com/en-us/library/ff728623%28v=exchg.150%29.aspx. All existing documentation (ISG, Admin Guide, IMT) will be updated shortly to reflect this change in requirements. hope that helps,Domenico.

Exchange 2010 SP1 Update Rollup 6 to Exchange 2010 SP3

Hi there,
I am planning to install Exchange 2010 SP3 next week and after reading some of the related comments on this site I got a little worried.
Our current Exchange environment consists of the following:
1 x CAS/HT Server
2 x Mailbox Server (members of a DAG)
The OS of the 3 servers is Windows Server 2008 R2 SP1. All servers are running Exchange 2010 SP1 Update Rollup 6.
The Execution Policies on our Exchange servers are set as follows:
– CAS/HT Server:
Scope ExecutionPolicy
MachinePolicy Undefined
UserPolicy Undefined
Process Undefined
CurrentUser Undefined
LocalMachine Unrestricted
– Mailbox Servers:
Scope ExecutionPolicy
MachinePolicy Undefined
UserPolicy Undefined
Process Undefined
CurrentUser Undefined
LocalMachine RemoteSigned
Please note that we do not have any Group Policies that defined the PowerShell script execution policy.
I would be very grateful if you (or any of the kind readers) could help me with following questions:
1- Do I have to change the execution policy on our Exchange servers before installing SP3? If I have to change a policy, what should I change? And how would you recommend I should do this?
2- After installing SP3 on a server, can I install the latest rollup update on this server before moving to the next server? For example, can I do the following:
i. Install SP3 followed by RU 5 on the CAS/HT server -> Apply the our custom settings
ii. Install SP3 followed by RU 5 on the first mailbox server
iii. Install SP3 followed by RU 5 on the second mailbox server
Many thanks,
M

Hi Amit,
Many thanks for the swift reply.
That's correct. We didn't set the Powershell execution policy via Group Policy. We only configured the execution policy of "LocalMachine" to "Unrestricted" on the CAS/HT server using the "Set-ExecutionPolicy" command on the server.
The mailbox servers' execution policies have not been changed and are set to those values by default.
I must admit, I go event more confused when I read the "http://support.microsoft.com/kb/2668686" and "http://support.microsoft.com/kb/2810617" articles.
But it looks like I shouldn't worry as our current Powershell execution policies shouldn't affect the upgrade. Right?

Exchange 2010 SP3 Rollup Update 6

Our Exchange environment is currently on Exchange 2010 SP3 RU3 and the Forefront Protection 2010 for Exchange server version is 11.0.713.0 (Rollup 3).
We planning to upgrade Exchange servers and install Exchange 2010 SP3 RU6, question which I have is it Mandatory to upgrade the Forefront Protection 2010 for Exchange server version is 11.0.727.0 (Rollup 4) before we install Exchange 2010 SP3 RU6 on the
Exchange servers.
Thanks,
AJ

Thanks Adam for the prompt response and yes I recall these cmdlets to disable and there is a similar cmdlet to enable it. Also after Exchange 2010 SP2 after some RU there is no need to disable FPE before installing RU however it is recommended to disable
it.
If you refer the comments section mentioned in the blog below it talks about it:-
http://blogs.technet.com/b/exchange/archive/2014/05/27/released-update-rollup-6-for-exchange-2010-service-pack-3.aspx
If you read the comment posted by James Knoch posted on this blog which is as below,
SP3 & the Rollup Updates are not supposed to require you to disable Forefront anymore, but it doesn't hurt to be safe and disable/enable it anyways. Make sure you are running Forefront Rollup 4 (http://support.microsoft.com/kb/2619883)
& the latest security update (http://www.microsoft.com/en-us/download/details.aspx?id=41836).
Above stated confused me a bit, is it mandatory to upgrade Forefront or it is NOT.
Thanks,
AJ

Exchange 2010 SP3 install

Similar Messages

Maybe you are looking for