Exchange 2013 journaling and JBOD

Is anyone using JBOD on exchange journaling servers? If yes, how is that working out for you?

Hi mombu,
Microsoft does not support Exchange server deployed on JBOD storage architecture without DAG. JBOD have two main advantages: full space utilization and cost effective. However, if you lose a single disk in the JBOD then there is a high likelihood that you
will lose data, as the concept of a JBOD does not include not fault tolerance.
So it is important to point out at this stage that JBODs should not be considered if you do not plan to use DAG.
More details about Exchange 2013 storage configuration and
high availability, for your reference:
http://technet.microsoft.com/en-us/library/ee832792(v=exchg.150).aspx
http://technet.microsoft.com/en-us/library/dn789066(v=exchg.150).aspx
Best Regards,
Allen Wang

Similar Messages

Exchange 2013 SP1 and CUCM 9.1.2 - Exch not recognizing called extension

I think I'm almost there in getting Exchange 2013 SP1 UM working with CUCM 9.1.2...I've got two issues at the moment that I need a little help with.
1) When I dial my VM pilot (6040) from a UM enabled extension it prompts to enter an extension. When I dial the same extension and let it ring to VM, Exchange picks up and says "the person you are trying to reach does not have a valid voice mail box
on our system".
2) This just started happening this afternoon, when I dial my VM pilot (6040) exch3 picks up as thats what I have my route pattern pointing to. If I enter the extension of a mailbox on exch2, I get stuck in a endless loop.
I've followed this post as a guide but it hasn't resolved my issue.
https://supportforums.cisco.com/discussion/11914031/exchange-2013-um-and-cucm-86
My Exchange environment looks like this:
Site 1:
exch1 - CAS/Mailbox, used for mainly utility type work, journal, dedicated SMTP flows etc
exch2 - CAS/Mailbox, part DAG13
exch3 - CAS/Mailbox, part of DAG13
Site 2:
exch2dr - CAS/Mailbox, part of DAG13
exch3dr - CAS/Mailbox, part of DAG13
DAG13 is stretched between two sites, there are no users at our DR site so CUCM is pointing to Site 1 for UM. Each site has an internet facing CAS-only server for OWA/EAS etc.
Any help is greatly appreciated. I'd love to get rid of Unity.
EDIT:
I just found this event in the event logs:
The Microsoft Exchange Unified Messaging service on the Mailbox server received a diverted call with ID "d51600-3a3140c5-9b8-c1414ac@EXCH3-IPADDR" for extension "4099" on UM dial plan "CUCM" from UM IP gateway "CUCM IP",
but no UM-enabled mailbox for the corresponding extension could be found. Please check the extension and make sure that the corresponding mailbox is enabled for UM and associated with the correct UM dial plan.

9.1.2 I think it is, we upgraded to avoid the known DNS bug
I cant see how to PM you either
The crux of it was outlined below with some tweaks
http://blogs.technet.com/b/canitpro/archive/2014/04/30/step-by-step-integration-between-exchange-2013-um-and-cisco-unified-communication-manager.aspx
As we have multiple combined role servers, our trunks are set up as follows:
1. 1 x CAS Trunk - contains all CAS Servers on port 5060
2. 4 x MBX Trunks - contains Maibox Server with ports 5062-5068
On top of that, we had to Allow "Redirecting Diversion Header Delivery - Inbound (and Outbound)" on the CAS Trunk but DISABLE it on the Mailbox Trunks
Also, make sure that you are using Telephone Extension Dial plans in Exchange 2013 (Despite them being unable to be associated with a 13 Server - EX13 answers for all calls anyway)
Lastly, the MS documentation is a little strange - it says that as your last step of UM migration, you should point your Call Manager to 2013 - I don't agree with that statement, EX13 routes calls back to 2010 UM Servers perfectly fine, so treat it the same
as any other CAS based service - point to 2013, and it will handle the rest

Exchange 2013 Journaling Best practices

I am using native Exchange 2013 Journaling for journal all external messages for all users. The size of journal mailbox is very huge. I am looking for best practices for journaling
in terms of journal mailbox size? Journal database size? Do I need to create multiple journal mailboxes? Do I enable achieving for journal mailbox? If archiving enabled, then what is max size for archive mailbox? I do not want to export mails to PSTs.
Appreciate help from others

Hi,
Do you mean the size limit for .pst file?
By default, in Outlook 2010 and Outlook 2013, the overall size of .pst file has a preconfigured limit of 50GB. In Outlook 2003 and Outlook 2007, the default .pst file size limit is 20 GB. If the file size is greater than the default size limit, you will
be unable to open the .pst file. However, we can modify this value by making changes to the Windows registry.
Here is a related article for your reference.
The file size limits of .pst and .ost files are larger in Outlook 2010 and Outlook 2013
http://support.microsoft.com/kb/982577
About the user mailbox size limit, there are no inherent size limits, you can set the size limit to unlimited if you want. But you need to take many factors into consideration as mentioned above.
Best regards,
Belinda
Belinda Ma
TechNet Community Support

Cross-forest migration to Exchange 2013 SP1 and Outlook 2013 SP1

Hello! I have two forest: Exchange 2010 SP2 RU5 - resource forest and Exchange 2013 SP1 - account forest. I make cross-forest migration from resource forest (linked mailboxes with account forest) to forest with Exchange 2013 SP1.
I have moved mailbox from resource forest exchange 2010 to exchange 2013 sp1 forest.
Outlook 2010 connect to migrated mailbox without any problem, but outlook 2013 sp1 cannot connect to migrated mailbox.
Error look like - cannot find exchange server.
I created new mailbox in Exchange 2013 organization and can connect to it with outlook 2010 and outlook 2013 sp1.
Someone have the same problem with migrated mailbox? How to solve it?
Truly, Valery Tyurin

You can use New-MoveRequest to perform a cross-forest move. Here is a well post and step-wise explanation you can check for cross forest migration from exchange 2010 to exchange 2013(http://msexchangeguru.com/2013/11/03/e2013crossforestmigration/).
Moreover, you can try this utility (
http://www.exchangemigrationtool.com/ ) to accomplish this task.

Exchange 2013 migration and Lync server

hi guys,
i wanna upgrade my exchange 2010 to 2013 in our company.
but i faced with a question
will exchange migration has effect on Lync server an should i reinstall it again in our caompany or not?
plz help me
thanks guys

Hi,
you will need to config IM in OWA for Exchange 2013 server.As i can remember voice and everything else should be fine.
Here is a guide for enabling IM in OWA:
http://www.expta.com/2010/09/how-to-integrate-lync-server-2010-with.html
Just remember to point DNS to the New Exchange 2013 server and it should be fine.
Please mark as helpful if you find my contribution useful or as an answer if it does answer your question. That will encourage me - and others - to take time out to help you. Thank you! Off2work

Native Exchange 2013 Journaling - Guidance over Storage Planning!

Hi,
We are currently exploring full envelope journaling service using Exchange 2013 with Sharepoint 2013 eDiscovery suite for ALL internal and external messages for a largish enterprise ~40K mailboxes and need to accurately plan storage for the dedicated Journal
servers; we have used the standard messagestats powershell script to get send / receive and average message size and have some valid metrics to utilize however there is next to no actual guidance on how to plan storage for journaling published?
My question concerns which metric to use - unique send and receive OR total send / receive figures; I have reached out to some of my default Microsoft contacts and dug into how FE Journaling works under the hood and my understanding is that it is total send
/ receive for every message would be more valid to plan against?
Any guidance would be great!

Hi,
Do you mean you want to plan storage for journaling in Exchange 2013?
The storage will keep increasing as long as the new conversation is recorded. Targeting only the specific recipients can minimizes storage which is based on your requirements.
Here is an article about journaling in Exchange 2013 for your reference.
http://technet.microsoft.com/en-GB/library/aa998649(v=exchg.150).aspx
Hope this is helpful to you.
Best regards,
Belinda Ma
TechNet Community Support

Exchange 2013 SP1 and SCOM 2012 R2

Hi there,
Hopefully someone can assist me with this issue, if it is one...
I am halfway through an Exchange migration, from Exchange 2010 SP3 on Server 2008 R2 to Exchange 2013 SP1 on Server 2012 R2.
76 users in total, roughly 80GB of Public Folders.
I have configured the 2013 environment with a cross datacenter DAG, also increased all of the timeouts of the cluster to take this into consideration, and everything appears to function as expected.
Added both 2013 machines to SCOM 2012 R2 for at least a week with no active users on it, and all monitoring reported ok, no issues.
Exchange 2010 is configured to use webmail.company.com for RPC over HTTP, which is what I have configured 2013 to use as well.
Implemented Microsoft ARR for client access to Exchange 2013, as opposed to ISA we've used for Exchange 2010.
A week ago, changed the DNS records for webmail.company.com from ISA to ARR, and all clients connected perfect.
Thought, ok, now we can start the migration. So far everything "seems" to be going perfect with the mailbox moves, however, SCOM is really noisy.
Attempted to reran the probe for EWS and got the error below:
Is there perhaps anyone that can assist me with these errors?
Cheers

FYI... IIS ARR is not supported for Exchange Server.
Check in event log if you are getting anything related to the issue.
About Outlook POP UP to end users. Check the event log on 2010/2013 for MRS events.
Are those mailboxes still moving or in move request?
Cheers,
Gulab Prasad
Technology Consultant
Blog:
http://www.exchangeranger.com    Twitter:
  LinkedIn:
   Check out CodeTwo’s tools for Exchange admins
Note: Posts are provided “AS IS” without warranty of any kind, either expressed or implied, including but not limited to the implied warranties of merchantability and/or fitness for a particular purpose.

Exchange 2013 SP1 and Exchange Online Protection (EOP)

Hello, I have just set up a new install of Exchange 2013 and connected mail flow with EOP. Mail is flowing, and I can access emails through the Outlook Web App. However, I cannot get Outlook 2013 to link up to the new configuration. I got Outlook for Mac
to work, no problem. But, I get an error on outlook 2013 that says it must sync folders for a first time to open.
Any help would be appreciated.
Thanks!

Hi
Use another user to test, check whether he can use Outlook to access his mailbox or not?
If this user also cannot connect to his mailbox, I suggest you go to check whether all the Exchange services are started, make sure RPC client access service is started.
You do need to replace the self-signed certificate.
If you don't want to buy a certificate from a Third-Party Issuer, then install Windows CA and issue a certificate from there.
Even if it does work with the self-signed certificate using Outlook 2007, it is not a supported configuration and you will not be able to connect with Outlook 2010/2013.
I have seen new installation of EX13 having SSLOffloading turned on causing the problems. Turn if off if you do.
Set-OutlookAnywhere -Identity 'SERVERNAME\rpc (Default Web Site)' -SSLOffloading $false
Let us know the output of the above so that we can proceed further.
Remember to mark as helpful if you find my contribution useful or as an answer if it does answer your question.That will encourage me - and others - to take time out to help you Check out my latest blog posts on http://exchangequery.com

Exchange 2013 ECP and DAG issue

Good Day,
We have Exchange 2013 setup in Coexistence with Exchange 2007. Everything is working well except for two small issues I have noticed.
Current Setup of 2013:
SiteA:
2x CAS Servers on Windows 2012 R2 configured with windows NLB (Internet Facing).
2x MBX servers Configured in a DAG also running on Windows 2012 R2.
SiteB:
2x CAS Server on Windows 2012 R2.
2x MBX servers Configured in a DAG also running on Windows 2012 R2.
Issues I am having:
Issue 1:
When working on the ECP:
I can do all tasks on servers in the same site but get some errors when trying to do tasks on servers in the other site.
When trying to Activate a DB copy on the DAG at SiteB I get "The Microsoft Exchange Replication service does not appear to be running on Server name"
And just trying to go to the properties of a server at SiteB "An error occurred while accessing the registry on the server servername"
This happens vice versa.
I can access all servers on the same site but not between sites with some tasks.
I have made sure firewall is disabled and remote registry is indeed running but no luck.
From a network perspective all ports are open between the sites.
Issue 2:
When I reboot a DAG member with the active mailbox databases for testing outlook connectivity I get two issues.
Then I cannot access ECP at all until the server is up again.
Outlook keeps staying on trying to connect until it is reopened.
Any Ideas?
I will gladly give more information if needed.
Thank You
Riaan Rourke
Senior System Engineer

Since I don't see this with Hyper-V I'll assume this is on ESX. Please let me know it that's not correct.
In terms of virtualization best practices - whose list was that :)
There are multiple configuration things that you *MUST* do when using WLBS on ESX. It will depend upon multiple things in the environment. I'd start with this
http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=1556
Fix that, and chances are the other item will be also remediated.
Cheers,
Rhoderick
Microsoft Senior Exchange PFE
Blog:
http://blogs.technet.com/rmilne
Twitter:   LinkedIn:
  Facebook:
  XING:
Note: Posts are provided “AS IS” without warranty of any kind, either expressed or implied, including but not limited to the implied warranties of merchantability and/or fitness for a particular purpose.

Exchange 2010 to Exchange 2013 Migration and Architect a resilient and high availability exchange setup

Hi,
I currently have a single Exchange 2010 Server that has all the roles supporting about 500 users. I plan to upgrade to 2013 and move to a four server HA Exchange setup (a CAS array with 2 Server as CAS servers and one DAG with 2 mailbox Servers). My
goal is to plan out the transition in steps with no downtime. Email is most critical with my company.
Exchange 2010 is running SP3 on a Windows Server 2010 and a Separate Server as archive. In the new setup, rather than having a separate server for archiving, I am just going to put that on a separate partition.
Here is what I have planned so far.
1. Build out four Servers. 2 CAS and 2 Mailbox Servers. Mailbox Servers have 4 partitions each. One for OS. Second for DB. Third for Logs and Fourth for Archives.
2. Prepare AD for exchange 2013.
3. Install Exchange roles. CAS on two servers and mailbox on 2 servers. Add a DAG. Someone had suggested to me to use an odd number so 3 or 5. Is that a requirement?
4. I am using a third party load balancer for CAS array instead of NLB so I will be setting up that.
5. Do post install to ready up the new CAS. While doing this, can i use the same parameters as assigned on exchange 2010 like can i use the webmail URL for outlook anywhere, OAB etc.
6. Once this is done. I plan to move a few mailboxes as test to the new mailbox servers or DAG.
7. Testing outlook setups on new servers. inbound and outbound email tests.
once this is done, I can migrate over and point all my MX records to the new servers.
Please let me know your thoughts and what am I missing. I like to solidify a flowchart of all steps that I need to do before I start the migration.
thank you for your help in advance

Hi,
okay, you can use 4 virtual servers. But there is no need to deploy dedicated server roles (CAS + MBX). It is better to deploy multi-role Exchange servers, also virtual! You could install 2 multi-role servers and if the company growths, install another multi-role,
and so on. It's much more simpler, better and less expensive.
CAS-Array is only an Active Directory object, nothing more. The load balancer controls the sessions on which CAS the user will terminate. You can read more at
http://blogs.technet.com/b/exchange/archive/2014/03/05/load-balancing-in-exchange-2013.aspx Also there is no session affinity required.
First, build the complete Exchange 2013 architecture. High availability for your data is a DAG and for your CAS you use a load balancer.
On channel 9 there is many stuff from MEC:
http://channel9.msdn.com/search?term=exchange+2013
Migration:
http://geekswithblogs.net/marcde/archive/2013/08/02/migrating-from-microsoft-exchange-2010-to-exchange-2013.aspx
Additional informations:
http://exchangeserverpro.com/upgrading-to-exchange-server-2013/
Hope this helps :-)

How to configure AD on windows 2012 server for Exchange 2013 internal and external email flow

Dear Experts,
I have to configure exchange 2013 on Windows server 2012 STD. Company has registered Static IP addresses and can get the MX record pointing to any of this Static IP.
The registered domain name is e.g. contoso.com.
a. What should I use as domain name on AD? contoso.com or contoso.local
b. Is it recommended to have two different servers for AD and Exchange?
c. What should be my connector settings for mail flow?
d. how can I set 2 email servers in company for load balancing?

Hi,
a, I suggest use contoso.com as domain name. It is convenient to add urls into our certificate for internal and external mail flow.
b, Recommended that installing AD
and Exchange Server on two separate
Servers. If Exchange Server downed unfortunately, it can prevent AD server from crushing at the same time.
c, Found some articles for your reference:
Configure Mail Flow and Client Access
http://technet.microsoft.com/en-us/library/jj218640(v=exchg.150).aspx
Configuring Outbound Mail Flow in Exchange Server 2013
http://exchangeserverpro.com/configuring-outbound-mail-flow-in-exchange-server-2013/
d, Load Balancing
http://technet.microsoft.com/en-us/library/jj898588(v=exchg.150).aspx
Hope it is helpful
Thanks
Mavis
Mavis Huang
TechNet Community Support

Exchange 2013 CU3 and Firefox 26.0

I upgraded Exchange 2013 to CU3 last night. I tested the mail flow and everything worked fine sending and recieving. The problem that I am having is with OWA in firefox 26.0 (currently newest version). I get weird graphical glitches when
OWA first loads. Once you click around the display stabilizes but the biggest problem is that not all of the emails are displayed in a folder. I have a folder with a bunch of system data emails that are collected throughout the day and in firefox
I can see ~20 while in IE 9 I can see them all. The inbox also has 5 emails in it but there is a scroll bar that is completely unnecessary in firefox but not IE 9. Do you have any thoughts on this? Thank you in advance.

There's no way, as there's nothing wrong with the server.
You will have to wait for the update from Firefox to get it fixed.
It's purely Browser issue As I said before.
Cheers,
Gulab Prasad,
Technology Consultant
Blog:
www.exchangeranger.com
Twitter:
LinkedIn:
Check out CodeTwo’s tools for Exchange admins
Note: Posts are provided “AS IS” without warranty of any kind, either expressed or implied, including but not limited to the implied warranties of merchantability and/or fitness for a particular purpose.

We have a Exchange 2013 server and the Mailbox Database folder is filling up with .log files.

We are migrating from Exchange 2010 to Exchange 2013. We have installed the Exchange 2013 but it only has a couple of mailboxes on this server, all the mailboxes are still on the Exchange 2010 server.
I have run a Windows Backup of the Exchange 2013 but I am still seeing a ton a log files in the mailbox folder.
Also the database file is only about 1.1 GB but the backup is now 40 GB.
Is there something that can be done to truncate these logs and make the backup smaller?

Hi ,
1.Does the full backup completed successfully ?
2.what about the status for the below mentioned command ? Does the mailbox database headers updated with the latest time and date ?
Get-MailboxDatabase -Status | ft name,*full* -au
3.Just check the application event logs for the event id
2046 and that should state that the log truncation for the mailbox databases has been initiated or not.
4.Before initiating the backup just make the exchange writer is not on error.
vssadmin list writers
In case if it on error state ,please restart the Microsoft exchange replication service and check the exchange writers status again by using the above mentioned command.
Thanks & Regards S.Nithyanandham

Exchange 2013 MP and DAG

Hi.
We got strange issue with Exchange 2013 MP. Some components in DAG are in state "Not monitoring". For example:
"Exchange 2013 Service Components" on DAG members not motitored:
Mailbox Count in organization is null:
And DAG object is in the "Not monitored" state too.
MP was installed as described in documentation (account, profile, etc.).
Proxy on DAG members enabled.
Any ideas how to troubleshoot this issue?
P.S. MP - 15.0.665.19, Exchange - CU6

Hi,
I would like to suggest you recheck Exchange 2013 Management Pack Pre-requisites and Considerations.
Before importing the Exchange 2013 MP into System Center Operations Manager, there are some pre-requisites that have to be met:
You have one of the following versions of System Center Operations Manager deployed in your organization:
System Center Operations Manager 2012 RTM or later
System Center Operations Manager 2007 R2 or later
You have already deployed SCOM agents to your Exchange Servers.
The SCOM agents on your Exchange Servers are running under the local system account.
The SCOM agents on your Exchange Servers are configured to act as a proxy and discover managed objects on other computers.
If you are monitoring Exchange Server 2013 Database Availability Groups (DAGs), ensure that all DAG members are monitored by Operations Manager.
You may refer to the link below for more details:
http://www.msexchange.org/articles-tutorials/exchange-server-2013/management-administration/monitoring-exchange-2013-scom-2012-part2.html
Regards,
Yan Li
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected]

Exchange 2013 POP3 and IMAP connectivity issues 0x800CCC0F

Hi all,
there's an Exchange 2013 server running without problems during "regular" use, but when it comes to POP3 and/or IMAP (we really need that for some systems), everything is fine until there's a message with an attachment of about 100kb or more.
We can poll messages with smaller attachments without problem, but bigger sizes won't work.
So for testing I tried POP3 within Outlook Express, it gives Error 0x800CCC0F
Telnet to TCP110 simply breaks up the connection when I try "retr"
IMAP shows those messages as "to be deleted", but they are accesible within OWA.
Test-PopConnectivity (also for IMAP) runs smoothly and successfully.
Firewall is opened for all connections.
Problem is and has always been there. The server is updated to the newest SP/updates.
I tried both 110/143 and corresponding SSL - no difference.
Pop3 and Imap logging shows no errors
There's Trend Micro Messaging Security installed, but has been disabled for testing - no difference. (Issue has been there before installation of TM)
So, any ideas how to fix this? I'd appreciate...
Thanks in advance,
Robert

Hello,
Take a network trace on both ends to see if there are any devices like firewalls drop the package.
http://www.microsoft.com/en-us/download/details.aspx?id=4865
Thanks,
Simon Wu
TechNet Community Support

Exchange 2013 journaling and JBOD

Similar Messages

Maybe you are looking for