Exchange 2013 SP1 and CUCM 9.1.2 - Exch not recognizing called extension
I think I'm almost there in getting Exchange 2013 SP1 UM working with CUCM 9.1.2...I've got two issues at the moment that I need a little help with.
1) When I dial my VM pilot (6040) from a UM enabled extension it prompts to enter an extension. When I dial the same extension and let it ring to VM, Exchange picks up and says "the person you are trying to reach does not have a valid voice mail box
on our system".
2) This just started happening this afternoon, when I dial my VM pilot (6040) exch3 picks up as thats what I have my route pattern pointing to. If I enter the extension of a mailbox on exch2, I get stuck in a endless loop.
I've followed this post as a guide but it hasn't resolved my issue.
https://supportforums.cisco.com/discussion/11914031/exchange-2013-um-and-cucm-86
My Exchange environment looks like this:
Site 1:
exch1 - CAS/Mailbox, used for mainly utility type work, journal, dedicated SMTP flows etc
exch2 - CAS/Mailbox, part DAG13
exch3 - CAS/Mailbox, part of DAG13
Site 2:
exch2dr - CAS/Mailbox, part of DAG13
exch3dr - CAS/Mailbox, part of DAG13
DAG13 is stretched between two sites, there are no users at our DR site so CUCM is pointing to Site 1 for UM. Each site has an internet facing CAS-only server for OWA/EAS etc.
Any help is greatly appreciated. I'd love to get rid of Unity.
EDIT:
I just found this event in the event logs:
The Microsoft Exchange Unified Messaging service on the Mailbox server received a diverted call with ID "d51600-3a3140c5-9b8-c1414ac@EXCH3-IPADDR" for extension "4099" on UM dial plan "CUCM" from UM IP gateway "CUCM IP",
but no UM-enabled mailbox for the corresponding extension could be found. Please check the extension and make sure that the corresponding mailbox is enabled for UM and associated with the correct UM dial plan.
9.1.2 I think it is, we upgraded to avoid the known DNS bug
I cant see how to PM you either
The crux of it was outlined below with some tweaks
http://blogs.technet.com/b/canitpro/archive/2014/04/30/step-by-step-integration-between-exchange-2013-um-and-cisco-unified-communication-manager.aspx
As we have multiple combined role servers, our trunks are set up as follows:
1. 1 x CAS Trunk - contains all CAS Servers on port 5060
2. 4 x MBX Trunks - contains Maibox Server with ports 5062-5068
On top of that, we had to Allow "Redirecting Diversion Header Delivery - Inbound (and Outbound)" on the CAS Trunk but DISABLE it on the Mailbox Trunks
Also, make sure that you are using Telephone Extension Dial plans in Exchange 2013 (Despite them being unable to be associated with a 13 Server - EX13 answers for all calls anyway)
Lastly, the MS documentation is a little strange - it says that as your last step of UM migration, you should point your Call Manager to 2013 - I don't agree with that statement, EX13 routes calls back to 2010 UM Servers perfectly fine, so treat it the same
as any other CAS based service - point to 2013, and it will handle the rest
Similar Messages
-
Exchange 2013 SP1 and SCOM 2012 R2
Hi there,
Hopefully someone can assist me with this issue, if it is one...
I am halfway through an Exchange migration, from Exchange 2010 SP3 on Server 2008 R2 to Exchange 2013 SP1 on Server 2012 R2.
76 users in total, roughly 80GB of Public Folders.
I have configured the 2013 environment with a cross datacenter DAG, also increased all of the timeouts of the cluster to take this into consideration, and everything appears to function as expected.
Added both 2013 machines to SCOM 2012 R2 for at least a week with no active users on it, and all monitoring reported ok, no issues.
Exchange 2010 is configured to use webmail.company.com for RPC over HTTP, which is what I have configured 2013 to use as well.
Implemented Microsoft ARR for client access to Exchange 2013, as opposed to ISA we've used for Exchange 2010.
A week ago, changed the DNS records for webmail.company.com from ISA to ARR, and all clients connected perfect.
Thought, ok, now we can start the migration. So far everything "seems" to be going perfect with the mailbox moves, however, SCOM is really noisy.
Attempted to reran the probe for EWS and got the error below:
Is there perhaps anyone that can assist me with these errors?
CheersFYI... IIS ARR is not supported for Exchange Server.
Check in event log if you are getting anything related to the issue.
About Outlook POP UP to end users. Check the event log on 2010/2013 for MRS events.
Are those mailboxes still moving or in move request?
Cheers,
Gulab Prasad
Technology Consultant
Blog:
http://www.exchangeranger.com Twitter:
LinkedIn:
Check out CodeTwo’s tools for Exchange admins
Note: Posts are provided “AS IS” without warranty of any kind, either expressed or implied, including but not limited to the implied warranties of merchantability and/or fitness for a particular purpose. -
Cross-forest migration to Exchange 2013 SP1 and Outlook 2013 SP1
Hello! I have two forest: Exchange 2010 SP2 RU5 - resource forest and Exchange 2013 SP1 - account forest. I make cross-forest migration from resource forest (linked mailboxes with account forest) to forest with Exchange 2013 SP1.
I have moved mailbox from resource forest exchange 2010 to exchange 2013 sp1 forest.
Outlook 2010 connect to migrated mailbox without any problem, but outlook 2013 sp1 cannot connect to migrated mailbox.
Error look like - cannot find exchange server.
I created new mailbox in Exchange 2013 organization and can connect to it with outlook 2010 and outlook 2013 sp1.
Someone have the same problem with migrated mailbox? How to solve it?
Truly, Valery TyurinYou can use New-MoveRequest to perform a cross-forest move. Here is a well post and step-wise explanation you can check for cross forest migration from exchange 2010 to exchange 2013(http://msexchangeguru.com/2013/11/03/e2013crossforestmigration/).
Moreover, you can try this utility (
http://www.exchangemigrationtool.com/ ) to accomplish this task. -
Exchange 2013 SP1 and Exchange Online Protection (EOP)
Hello, I have just set up a new install of Exchange 2013 and connected mail flow with EOP. Mail is flowing, and I can access emails through the Outlook Web App. However, I cannot get Outlook 2013 to link up to the new configuration. I got Outlook for Mac
to work, no problem. But, I get an error on outlook 2013 that says it must sync folders for a first time to open.
Any help would be appreciated.
Thanks!Hi
Use another user to test, check whether he can use Outlook to access his mailbox or not?
If this user also cannot connect to his mailbox, I suggest you go to check whether all the Exchange services are started, make sure RPC client access service is started.
You do need to replace the self-signed certificate.
If you don't want to buy a certificate from a Third-Party Issuer, then install Windows CA and issue a certificate from there.
Even if it does work with the self-signed certificate using Outlook 2007, it is not a supported configuration and you will not be able to connect with Outlook 2010/2013.
I have seen new installation of EX13 having SSLOffloading turned on causing the problems. Turn if off if you do.
Set-OutlookAnywhere -Identity 'SERVERNAME\rpc (Default Web Site)' -SSLOffloading $false
Let us know the output of the above so that we can proceed further.
Remember to mark as helpful if you find my contribution useful or as an answer if it does answer your question.That will encourage me - and others - to take time out to help you Check out my latest blog posts on http://exchangequery.com -
Hello,
if I create a new task from OWA, I can't see the the information of the notice field in Outlook 2013
But when I create a new task in Outlook 2013, I can see the Information of the notice field in OWA and then when I edit this task in OWA the information field will be empty after Change this field there.
This is a very strange issue, please help!
Regards
BerndHi,
To work around this issue, use one of the following methods to verify the quota status of mailboxes.
Method 1: Use Exchange Admin Console (EAC)
If you want to verify the status of individual mailbox quotas, follow these steps: 1.Log on to EAC by using a user account that is assigned at least the Mail Recipients role.
2.In the feature pane, click recipients. A list of mailboxes is displayed.
3.Select the mailbox of which you want to verify the quota status, and then click the Edit button on the toolbar.
4.Click mailbox usage. The mailbox quota usage is displayed.
Method 2: Use Exchange Management Shell
If you want to verify the status of individual mailbox quota, run the following command in Exchange Management Shell:
Get-MailboxStatistics DisplayName | ft *quota*,*size -AutoSize –Wrap
If you want to verify the status of the mailbox quota for all the mailboxes that are hosted on a database, run the following command:
Get-MailboxStatistics -Database DatabaseName | ft displayname,*quota*,*size -AutoSize –Wrap
Thanks,
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact
[email protected]
Simon Wu
TechNet Community Support -
I have a new Exchange 2013 server with plans to migrate from my current Exchange 2007 Server.
I installed Exchange 2013 SP1 and the only errors I saw in the event log seemed to be long standing known issues that did not indicate an actual problem (based on what I read online).
I updated to CU7 and now lots of errors have appeared (although the old ones seem to have been fixed so I have that going for me).
Currently the Exchange 2013 server is not in use and clients are still hitting the 2007 server.
Issue 1)
After each reboot I get a Kernel-EventTracing 2 error. I cannot find anything on this on the internet so I have no idea what it is.
Session "FastDocTracingSession" failed to start with the following error: 0xC0000035
I did read other accounts of this error with a different name in the quotes but still can’t tell what this is or where it is coming from.
Issue 2)
I am still getting 5 MSExchange Common 106 errors even after reregistering all of the perf counters per this page:
https://support.microsoft.com/kb/2870416?wa=wsignin1.0
One of the perf counters fails to register using the script from the link above.
66 C:\Program Files\Microsoft\Exchange Server\V15\Setup\Perf\InfoWorkerMultiMailboxSearchPerformanceCounters.xml
New-PerfCounters : The performance counter definition file is invalid.
At C:\Users\administrator.<my domain>\Downloads\script\ReloadPerfCounters.ps1:19 char:4
+ New-PerfCounters -DefinitionFileName $f
+ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+ CategoryInfo
: InvalidData: (:) [New-PerfCounters], TaskException
+ FullyQualifiedErrorId : [Server=VALIS,RequestId=71b6bcde-d73e-4c14-9a32-03f06e3b2607,TimeStamp=12/18/2014 10:09:
12 PM] [FailureCategory=Cmdlet-TaskException] 33EBD286,Microsoft.Exchange.Management.Tasks.NewPerfCounters
But that one seems unrelated to the ones that still throw errors.
Three of the remaining five errors are (the forum is removing my spacing between the error text so it looks like a wall of text - sorry):
Performance counter updating error. Counter name is Count Matched LowFidelity FingerPrint, but missed HighFidelity FingerPrint, category name is MSExchange Anti-Malware Datacenter Perfcounters. Optional code: 3. Exception: The
exception thrown is : System.InvalidOperationException: The requested Performance Counter is not a custom counter, it has to be initialized as ReadOnly.
at System.Diagnostics.PerformanceCounter.InitializeImpl()
at System.Diagnostics.PerformanceCounter.set_RawValue(Int64 value)
at Microsoft.Exchange.Diagnostics.ExPerformanceCounter.set_RawValue(Int64 value)
Last worker process info : System.ArgumentException: Process with an Id of 7384 is not running.
at System.Diagnostics.Process.GetProcessById(Int32 processId)
at Microsoft.Exchange.Diagnostics.ExPerformanceCounter.GetLastWorkerProcessInfo()
Performance counter updating error. Counter name is Number of items, item is matched with finger printing cache, category name is MSExchange Anti-Malware Datacenter Perfcounters. Optional code: 3. Exception: The exception thrown
is : System.InvalidOperationException: The requested Performance Counter is not a custom counter, it has to be initialized as ReadOnly.
at System.Diagnostics.PerformanceCounter.InitializeImpl()
at System.Diagnostics.PerformanceCounter.set_RawValue(Int64 value)
at Microsoft.Exchange.Diagnostics.ExPerformanceCounter.set_RawValue(Int64 value)
Last worker process info : System.ArgumentException: Process with an Id of 7384 is not running.
at System.Diagnostics.Process.GetProcessById(Int32 processId)
at Microsoft.Exchange.Diagnostics.ExPerformanceCounter.GetLastWorkerProcessInfo()
Performance counter updating error. Counter name is Number of items in Malware Fingerprint cache, category name is MSExchange Anti-Malware Datacenter Perfcounters. Optional code: 3. Exception: The exception thrown is : System.InvalidOperationException:
The requested Performance Counter is not a custom counter, it has to be initialized as ReadOnly.
at System.Diagnostics.PerformanceCounter.InitializeImpl()
at System.Diagnostics.PerformanceCounter.set_RawValue(Int64 value)
at Microsoft.Exchange.Diagnostics.ExPerformanceCounter.set_RawValue(Int64 value)
Last worker process info : System.ArgumentException: Process with an Id of 7384 is not running.
at System.Diagnostics.Process.GetProcessById(Int32 processId)
at Microsoft.Exchange.Diagnostics.ExPerformanceCounter.GetLastWorkerProcessInfo()
Issue 3)
I appear to have some issues related to the healthmailboxes.
I get MSExchangeTransport 1025 errors for multiple healthmailboxes.
SMTP rejected a (P1) mail from 'HealthMailbox23b10b91745648819139ee691dc97eb6@<my domain>.local' with 'Client Proxy <my server>' connector and the user authenticated as 'HealthMailbox23b10b91745648819139ee691dc97eb6'. The Active Directory
lookup for the sender address returned validation errors. Microsoft.Exchange.Data.ProviderError
I reran setup /prepareAD to try and remedy this but I am still getting some.
Issue 4)
I am getting an MSExchange RBAC 74 error.
(Process w3wp.exe, PID 984) Connection leak detected for key <my domain>.local/Admins/Administrator in Microsoft.Exchange.Configuration.Authorization.WSManBudgetManager class. Leaked Value 1.
Issue 5)
I am getting MSExchange Assistants 9042 warnings on both databases.
Service MSExchangeMailboxAssistants. Probe Time Based Assistant for database Database02 (c83dbd91-7cc4-4412-912e-1b87ca6eb0ab) is exiting a work cycle. No mailboxes were successfully processed. 2 mailboxes were skipped due to errors. 0 mailboxes were
skipped due to failure to open a store session. 0 mailboxes were retried. There are 0 mailboxes in this database remaining to be processed.
Some research suggested this may be related to deleted mailboxes however I have never had any actual user mailboxes on this server.
If they are healthmailboxes or arbitration mailboxes that might make sense but I am unsure of what to do on this.
Issue 6)
At boot I am getting an MSExchange ActiveSync warning 1033
The setting SupportedIPMTypes in the Web.Config file was missing.
Using default value of System.Collections.Generic.List`1[System.String].
I don't know why but this forum is removing some of my spacing that would make parts of this easier to read.Hi Eric
Yes I have uninstalled and reinstalled Exchange 2013 CU7 for the 3<sup>rd</sup> time.
I realize you said one issue per forum thread but since I already started this thread with many issues I will at least post what I have discovered on them in case someone finds their way here from a web search.
I have an existing Exchange 2007 server in the environment so I am unable to create email address policies that are defined by “recipient container”.
If I try and do so I get “You can't specify the recipient container because legacy servers are detected.”
So I cannot create a normal email address policy and restrict it to an OU without resorting to some fancy filtering.
Instead what I have done is use PS to modify extensionAttribute1 (otherwise known as Custom Attribute 1 to exchange) for all of my users.
I then applied an address policy to them and gave it the highest priority.
Then I set a default email address policy for the entire organization.
After reinstalling Exchange all of my system mailboxes were created with the internal domain name.
So issue number 3 above has not come up.
For issue number one above I have created a new thread:
https://social.technet.microsoft.com/Forums/office/en-US/7eb12b89-ae9b-46b2-bd34-e50cd52a4c15/microsoftwindowskerneleventtracing-error-2-happens-twice-at-boot-ex2013cu7?forum=exchangesvrdeploy
For issue number four I have posted to this existing thread where there is so far no resolution:
https://social.technet.microsoft.com/Forums/exchange/en-US/2343730c-7303-4067-ae1a-b106cffc3583/exchange-error-id-74-connection-leak-detected-for-key?forum=exchangesvradmin
Issue number Five I have managed to recreate and get rid of in more than one way.
If I create a new database in ECP and set the database and log paths where I want, then this error will appear.
If I create the database in the default location and then use EMS to move it and set the log path, then the error will not appear.
The error will also appear (along with other errors) if I delete the health mailboxes and let them get recreated by restarting the server or the Health Manager service.
If I then go and set the retention period for deleted mailboxes to 0 days and wait a little while, these will all go away.
So my off hand guess is that these are caused by orphaned system mailboxes.
For issue number six I have posted to this existing thread where there is so far no resolution:
https://social.technet.microsoft.com/Forums/exchange/en-US/dff62411-fad8-4d0c-9bdb-037374644845/event-1033-msexchangeactivesync-warning?forum=exchangesvrmobility
So for the remainder of this thread we can try and tackle issue number two which is the perf counters.
The exact same 5 perf counter were coming up and this had been true each time I have uninstalled and reinstalled Exchange 2013CU7.
Actually to be more accurate a LOT of perf counter errors come up after the initial install, but reloading the perf counters using the script I posted above reduces it to the same five.
Using all of your suggestions so far has not removed these 5 remaining errors either. Since there is no discernible impact other than these errors at boot I am not seriously bothered by them but as will all event log errors, I would prefer
to make them go away if possible. -
Error while adding member to the dag in exchange 2013 sp1
I have Windows Server 2012 Std Edition with Exchange 2013 SP1 and get the following error while adding member to the dag either i do it using EAC or the powershell
Senior Technical Consultant, MDS ComputersWhen running set-databaseavailabilitygroup Exchange-dag without parameters, it crashes again:
[PS] C:\Windows\system32>Set-DatabaseAvailabilityGroup exchange-dag
WARNING: An unexpected error has occurred and a Watson dump is being generated: Some or all identity references could not be translated. Some or all identity references could not be translated.
+ CategoryInfo : NotSpecified: (:) [Set-DatabaseAvailabilityGroup], IdentityNotMappedException
+ FullyQualifiedErrorId : System.Security.Principal.IdentityNotMappedException,Microsoft.Exchange.Management.Syste
mConfigurationTasks.SetDatabaseAvailabilityGroup
+ PSComputerName : <server>
Also, this is logged in the eventlog:
Watson report about to be sent for process id: 7424, with parameters: E12, c-RTL-AMD64, 15.00.0847.032, w3wp#MSExchangePowerShellAppPool, M.Exchange.Management, M.E.M.C.FileShareWitness.Create, S.S.Principal.IdentityNotMappedException, 3e5c, 15.00.0847.031.
ErrorReportingEnabled: True
Definitely looks like a problem creating the filewitness share.
Frank. -
Exchange 2013 SP1 | Another HTTP 500.0.0 Error
Help!
We are in the middle of migrating from Exchange 2010 SP3 to Exchange 2013 SP1 and we are being plagued with HTTP 500 errors on every Exchange 2013 server now.
I have two Client Access servers installed (EXCHFE01 & EXCHFE02) and one backend mailbox server (EXCHMB03) with the Client Access role also installed (for troubleshooting purposes). Once I get everything working I'll install two backend 2013 servers
with the mailbox role only for production (load-balanced, clustered, etc). I still have two Exchange 2010 mailbox servers left since one has a single large mailbox left on it and the other hosts public folders. I'll get to migrating those later. All Exchange
2013 servers are running Windows Server 2012. All are on the same LAN and no firewalls are between them.
On all three 2013 servers (EXCHFE01, EXCHFE02, EXCHMB03) I'm getting the dreaded HTTP 500 error whether I try to get to OWA or ECP. This did work at one point where I could at least login to the mailbox server (EXCHMB03) and migrate all my mailboxes over
to it. Sometime this morning after the two Client Access servers were installed the mailbox server stopped working (HTTP 500 errors). This is very frustrating because I can't even login to a console to manage Exchange from any server at this point.
Both Client Access servers aren't really showing anything of value in the event logs or the IIS logs. The mailbox server (EXCHMB03) does show the following event 3002:
Protocol /Microsoft-Server-ActiveSync failed to process request from identity NT AUTHORITY\SYSTEM. Exception: Microsoft.Exchange.Security.Authentication.BackendRehydrationException: Rehydration failed. Reason: Source server 'NT AUTHORITY\SYSTEM' does not have token serialization permission.
at Microsoft.Exchange.Security.Authentication.BackendRehydrationModule.ProcessRequest(HttpContext httpContext)
at Microsoft.Exchange.Security.Authentication.BackendRehydrationModule.OnAuthenticateRequest(Object source, EventArgs args).
...and I get the following when I run the Exchange Management Shell tool on the same mailbox server (along with lots of other red HTML text):
More Information:
This error means that there was a problem while processing the request. The request was received by the Web server, but during processing a fatal error occurred, causing the 500 error.
The Client Access servers show the following errors:
Performance counter updating error. Counter name is Location cache update time, category name is MSExchange Active Manager Client. Optional code: 3. Exception: The exception thrown is : System.InvalidOperationException: The requested Performance Counter is not a custom counter, it has to be initialized as ReadOnly.
at System.Diagnostics.PerformanceCounter.InitializeImpl()
at System.Diagnostics.PerformanceCounter.set_RawValue(Int64 value)
at Microsoft.Exchange.Diagnostics.ExPerformanceCounter.set_RawValue(Int64 value)
Last worker process info : System.ArgumentException: Process with an Id of 4040 is not running.
at System.Diagnostics.Process.GetProcessById(Int32 processId)
at Microsoft.Exchange.Diagnostics.ExPerformanceCounter.GetLastWorkerProcessInfo()
Processes running while Performance counter failed to update:
888 svchost
264 smss
532 conhost
2576 Microsoft.Exchange.UM.CallRouter
1596 WMSvc
3932 dllhost
4020 svchost
2308 dwm
5060 taskhostex
844 svchost
1972 Microsoft.Exchange.Directory.TopologyService
1228 inetinfo
1316 vmtoolsd
3896 svchost
780 svchost
1580 rundll32
1668 mqsvc
816 dwm
3840 slui
3532 rdpclip
3980 WmiPrvSE
4200 SppExtComObj
4288 winlogon
2140 SMSvcHost
676 svchost
1564 svchost
1296 Microsoft.Exchange.Diagnostics.Service
1472 Microsoft.Exchange.ServiceHost
1204 svchost
1292 ServerManagerLauncher
488 winlogon
664 svchost
572 lsass
3236 dllhost
2972 WmiPrvSE
4484 w3wp
388 csrss
1600 rundll32
564 services
1260 msdtc
5032 sppsvc
1448 MSExchangeHMHost
824 LogonUI
4204 VSSVC
2524 userinit
2700 MSExchangeFrontendTransport
1708 SMSvcHost
728 svchost
460 wininit
904 svchost
992 svchost
4996 TSTheme
4240 slui
4904 taskhost
452 csrss
4340 csrss
4 System
1164 spoolsv
1988 slClient
2760 MSExchangeHMWorker
0 Idle
Performance Counters Layout information: FileMappingNotFoundException for category MSExchange Active Manager Client : Microsoft.Exchange.Diagnostics.FileMappingNotFoundException: Cound not open File mapping for name Global\netfxcustomperfcounters.1.0msexchange active manager client. Error Details: 2
at Microsoft.Exchange.Diagnostics.FileMapping.OpenFileMapping(String name, Boolean writable)
at Microsoft.Exchange.Diagnostics.PerformanceCounterMemoryMappedFile.Initialize(String fileMappingName, Boolean writable)
at Microsoft.Exchange.Diagnostics.ExPerformanceCounter.GetAllInstancesLayout(String categoryName)
... and...
A transient failure has occurred. The problem may resolve itself. Diagnostic information:
Microsoft.Exchange.Data.DataSourceOperationException: The request failed. The remote server returned an error: (503) Server Unavailable. ---> Microsoft.Exchange.WebServices.Data.ServiceRequestException: The request failed. The remote server returned an error: (503) Server Unavailable. ---> System.Net.WebException: The remote server returned an error: (503) Server Unavailable.
at System.Net.HttpWebRequest.GetResponse()
at Microsoft.Exchange.WebServices.Data.EwsHttpWebRequest.Microsoft.Exchange.WebServices.Data.IEwsHttpWebRequest.GetResponse()
at Microsoft.Exchange.WebServices.Data.ServiceRequestBase.GetEwsHttpWebResponse(IEwsHttpWebRequest request)
--- End of inner exception stack trace ---
at Microsoft.Exchange.WebServices.Data.ServiceRequestBase.GetEwsHttpWebResponse(IEwsHttpWebRequest request)
at Microsoft.Exchange.WebServices.Data.ServiceRequestBase.ValidateAndEmitRequest(IEwsHttpWebRequest& request)
at Microsoft.Exchange.WebServices.Data.ExchangeService.InternalFindFolders(IEnumerable`1 parentFolderIds, SearchFilter searchFilter, FolderView view, ServiceErrorHandling errorHandlingMode)
at Microsoft.Exchange.WebServices.Data.ExchangeService.FindFolders(FolderId parentFolderId, SearchFilter searchFilter, FolderView view)
at Microsoft.Exchange.Data.Storage.Management.EwsStoreDataProvider.InvokeServiceCall[T](Func`1 callback)
--- End of inner exception stack trace ---
at Microsoft.Exchange.Data.Storage.Management.EwsStoreDataProvider.InvokeServiceCall[T](Func`1 callback)
at Microsoft.Exchange.Data.Storage.Management.EwsStoreDataProvider.GetOrCreateFolderCore(String folderName, FolderId parentFolder, Func`1 creator)
at Microsoft.Exchange.Data.Storage.Management.AsyncOperationNotificationDataProvider.GetDefaultFolder()
at Microsoft.Exchange.Data.Storage.Management.EwsStoreDataProvider.<>c__DisplayClass1b`1.<InternalFindPaged>b__13()
at Microsoft.Exchange.Data.Storage.Management.EwsStoreDataProvider.InvokeServiceCall[T](Func`1 callback)
at Microsoft.Exchange.Data.Storage.Management.EwsStoreDataProvider.<InternalFindPaged>d__21`1.MoveNext()
at Microsoft.Exchange.Data.Storage.Management.AsyncOperationNotificationDataProvider.<GetNotificationDetails>d__4.MoveNext()
at System.Linq.Enumerable.WhereEnumerableIterator`1.MoveNext()
at Microsoft.Exchange.Servicelets.CertificateNotificationServicelet.RemoveAllNotification()
at Microsoft.Exchange.Servicelets.CertificateNotificationServicelet.UpdateDataInMbx(List`1 certificates)
at Microsoft.Exchange.Servicelets.CertificateNotificationServicelet.Work()
I've tried all sorts of recommended fixes but none have worked so far:
ADSIEdit and remove msExchCanaryData0 data
Reinstall Exchange multiple times
Rebooted multiple times
This article: http://social.technet.microsoft.com/Forums/exchange/en-US/08d3777c-dc03-4411-8c87-7db37d2f406a/exchange-2013-owa-login-error-http-500?forum=exchangesvrclients
Rebooted DCs multiple times (no exchange servers are DCs)
I'm sure I've left out a few troubleshooting steps since I've been working at this for two days. Can anybody offer any advice? I'm at my wits end here...Hi,
Please check whether the mail.mydomain.com is pointed to your Exchange 2010 or Exchange 2013. Please run the following command to check your OWA virtual directores and ECP virtual directories:
Get-OwaVirtualDirectory -ShowMailboxVirtualDirectories | Select Identity,name,Internalurl,ExternalUrl,*auth*
Get-EcpVirtualDirectory -ShowMailboxVirtualDirectories | Select Identity,name,Internalurl,ExternalUrl,*auth*
In IIS manager > Default Web Site, please make sure Anonymous Authentication is Enabled in Authentication. Confirm that "Require SSL" is checked on the SSL Settings of the default web site.
Regards,
Winnie Liang
TechNet Community Support -
Exchange 2013 SP1 users not receiving quota warning email message
Hi,
We are on Exchange 2013 SP1 and Exchange 2010 SP3 co-existence mode and currently migrating users from Exchange 2010 to 2013. We have noticed that users are not receiving email message when their mailbox quota warning when its near to maximum limit.
If I log in via OWA it shows the notification (Pop up) that your mailbox is almost full but no message received in email. Most of the users do not log into OWA but only uses Outlook.
It looks like other people are also seeing this similar issue but I am unable to find any solution for it.
How users will know if their mailbox is almost full if they are traveling and only using Mobile phone for emails to send and receive.
Thanks,
RamanHi Thanks for your response. Our Quota is set on Database level. I am seeing these event ids as well.
Log Name: Application Source: MSExchangeIS Date: 12/31/2014 10:07:12 PM Event ID: 1077 Task Category: MAPI Level: Warning Keywords: Classic User: N/A Computer: Exch2013mail01.company.com Description: The mailbox e3d48b23-0740-46ab-89f7-3b035dacf28f on database
326f0997-4fe5-4b31-873b-6a3396e7a91c is approaching its storage limit. A notification has been sent to the user. This warning will not be sent again for at least twenty four hours.
========================
Log Name: Application Source: MSExchange Store Driver Submission Date: 12/31/2014 10:07:12 PM Event ID: 1012 Task Category: MSExchangeStoreDriverSubmission Level: Error Keywords: Classic User: N/A Computer: Exch2013mail01.company.com Description: The store
driver failed to submit event 8237691 mailbox e3d48b23-0740-46ab-89f7-3b035dacf28f MDB 326f0997-4fe5-4b31-873b-6a3396e7a91c and couldn't generate an NDR due to exception Microsoft.Exchange.MailboxTransport.StoreDriverCommon.InvalidSenderException at Microsoft.Exchange.MailboxTransport.Shared.SubmissionItem.SubmissionItemUtils.CopySenderTo(SubmissionItemBase
submissionItem, TransportMailItem message) at Microsoft.Exchange.MailboxTransport.Submission.StoreDriverSubmission.MailItemSubmitter.GenerateNdrMailItem() at Microsoft.Exchange.MailboxTransport.Submission.StoreDriverSubmission.MailItemSubmitter.<>c__DisplayClass1.<SubmitNdrForFailedSubmission>b__0()
at Microsoft.Exchange.MailboxTransport.StoreDriverCommon.StorageExceptionHandler.RunUnderTableBasedExceptionHandler(IMessageConverter converter, StoreDriverDelegate workerFunction).
Raman -
In exchange 2013 sp1 SUBMITFAIL event id is happening
Hi ,
In exchange 2013 sp1 SUBMITFAIL event id is happening for some messages .But at the second time that the same message is delivered perfectly to the end users.
My question is simple ,is this an bug in exchange 2013 sp1 if so on which CU it will be corrected ?We have to update to our customers so all of us please provide your suggestions as soon as possible.
Thanks & Regards S.NithyanandhamHi Allen Wang ,
Thanks a lot for your response.
Which version are you used? Is this issue arise after install update for Exchange server?
We are using exchange 2013 sp1 Ent edition.This issue is been existing in my environment when we start to use exchange 2013 and it is not from sp1 .
Also, what your means of “second time”, server retry to send or send failed then user click to resend?
When an user send an email for the first time to some of the recipient's it is reaching only to the few recipient's mailboxes and the email to the remaining recipients gets failed with the event ID "SUBMITFAIL" on the message tracking log.
Same time if we forward that same message to the failed recipients it went and delivered successfully.
Note : Apart from message tracking log i didn't found anything helpful in protocol and event viewer logs.
Below link is for your Reference :
https://social.technet.microsoft.com/Forums/fr-FR/ae61d80c-58da-4f47-b83c-66b123b2faf4/exchange-2013-mailflow-and-the-hosts-file?forum=exchangesvrgeneral
Above is the link which is saying that this issue will be resolved in exchange 2013 sp1 and also it says it an bug in exchange 2013 CU3 .But still on my end the problems occurs in exchange 2013 CU3 as well as in exchange 2013 SP1.
Please help me out yaar this issue is raising in my production environment.
Thanks & Regards S.Nithyanandham -
Exchange 2013 Sp1 Coexistence with Exchange 2010 SP3 CU5 HTTP 500
I`m trying to make working OWA coexistence between Exchange 2013 SP1 and Exchange 2010 SP3 CU5.
When user login in to OWA where his mailbox is located on Exchange 2013 server it logon successful and owa opened. When i try to login to the same url with user whose mailbox is located on Exchange 2010 server i get Error http 50
The website cannot display the page : HTTP 500 »https://URLEXCHANGE2013/owa/auth.owa«
The same is, when i use https:// URLEXCHANGE2013/ecp?ExchClientVer=14
URL on Exchange 2013 are different as fro Exchange 2010.
I even tried to setup Internal URL for Exchange 2010 to bi set to »null ,Saem error
Exchange server 2013 Sp1 is installed on Windows server 2012 R2.Assumption is correct. I have even enable verbose logging, and i can see MSExchange Front End HTTP Proxy , that successfully connect to Exchange 2010 server.
But remember Exchange 2013 is fresh installation on Windows server 2012 R2.
IIS LOG
2014-03-04 08:52:53 fe80::99d1:f542:a4d3:b469%12 RPC_IN_DATA /rpc/rpcproxy.dll [email protected]:6001&CorrelationID=<empty>;&RequestId=391fd8b3-2b98-494a-8812-d38feda2e5a0&cafeReqId=391fd8b3-2b98-494a-8812-d38feda2e5a0;
443 companyNT\SM_9c071c4922fd420fb fe80::99d1:f542:a4d3:b469%12 MSRPC - 200 0 0 5484
2014-03-04 08:52:53 fe80::99d1:f542:a4d3:b469%12 RPC_IN_DATA /rpc/rpcproxy.dll [email protected]:6001&CorrelationID=<empty>;&RequestId=27cfafa2-8224-4563-918b-0b228c6ee8d4&cafeReqId=27cfafa2-8224-4563-918b-0b228c6ee8d4;
443 - fe80::99d1:f542:a4d3:b469%12 MSRPC - 401 1 2148074254 0
2014-03-04 08:52:53 fe80::99d1:f542:a4d3:b469%12 RPC_OUT_DATA /rpc/rpcproxy.dll [email protected]:6001&CorrelationID=<empty>;&RequestId=6d930bcd-7bbc-415a-a25a-8d6488e91401&cafeReqId=6d930bcd-7bbc-415a-a25a-8d6488e91401;
443 - fe80::99d1:f542:a4d3:b469%12 MSRPC - 401 1 2148074254 15
2014-03-04 08:52:55 10.1.0.36 GET /owa/ &CorrelationID=<empty>;&cafeReqId=551cfdd9-18ac-42d8-aea3-cbb546c9d9fb; 443 - 10.1.0.36 Mozilla/4.0+(compatible;+MSIE+7.0;+Windows+NT+6.3;+WOW64;+Trident/7.0;+.NET4.0E;+.NET4.0C) https://OWA.company.com/
302 0 0 9937
2014-03-04 08:52:56 10.1.0.36 GET /owa/auth/logon.aspx url=https%3a%2f%2fOWA.company.com%2fowa%2f&reason=0&CorrelationID=<empty>;&cafeReqId=c1b97df9-ec56-4906-b2f5-965551b720ae; 443 - 10.1.0.36 Mozilla/4.0+(compatible;+MSIE+7.0;+Windows+NT+6.3;+WOW64;+Trident/7.0;+.NET4.0E;+.NET4.0C)
https://OWA.company.com/ 200 0 0 1015
2014-03-04 08:52:56 10.1.0.36 GET /owa/auth/logon.aspx replaceCurrent=1&url=https%3a%2f%2fOWA.company.com%2fowa%2f&CorrelationID=<empty>;&cafeReqId=b92ca682-04f4-4d4f-931e-9a95680ab9ea; 443 - 10.1.0.36 Mozilla/4.0+(compatible;+MSIE+7.0;+Windows+NT+6.3;+WOW64;+Trident/7.0;+.NET4.0E;+.NET4.0C)
- 200 0 0 671
2014-03-04 08:52:58 10.1.0.36 GET /ecp/ &CorrelationID=<empty>;&cafeReqId=093bd01a-de59-4519-80f6-067484122091; 443 - 10.1.0.36 Mozilla/4.0+(compatible;+MSIE+9.0;+Windows+NT+6.1;+MSEXCHMON;+ACTIVEMONITORING) - 302 0 0 0
2014-03-04 08:52:58 10.1.0.36 GET /owa/auth/logon.aspx url=https%3a%2f%2fEXCH2013%2fecp%2f&reason=0&CorrelationID=<empty>;&cafeReqId=c2f7565d-ee6a-48f8-8d86-16d5d3ca65c1; 443 - 10.1.0.36 Mozilla/4.0+(compatible;+MSIE+9.0;+Windows+NT+6.1;+MSEXCHMON;+ACTIVEMONITORING)
- 200 0 0 0
2014-03-04 08:52:58 10.1.0.36 GET /ecp/ &CorrelationID=<empty>;&cafeReqId=ba633030-2376-4bad-a32f-8f160bd87bd4; 443 - 10.1.0.36 Mozilla/4.0+(compatible;+MSIE+9.0;+Windows+NT+6.1;+MSEXCHMON;+ACTIVEMONITORING) - 302 0 0 0
2014-03-04 08:52:58 10.1.0.36 GET /owa/auth/logon.aspx url=https%3a%2f%2fEXCH2013%2fecp%2f&reason=0&CorrelationID=<empty>;&cafeReqId=5e94172c-d97c-46a9-a602-6030d6f7da2c; 443 - 10.1.0.36 Mozilla/4.0+(compatible;+MSIE+9.0;+Windows+NT+6.1;+MSEXCHMON;+ACTIVEMONITORING)
- 200 0 0 0
2014-03-04 08:52:58 10.1.0.36 GET /owa/auth/logon.aspx replaceCurrent=1&url=https%3a%2f%2fEXCH2013%2fecp%2f&CorrelationID=<empty>;&cafeReqId=9ba2caf3-2a03-44a2-8477-2724689e139c; 443 - 10.1.0.36 Mozilla/4.0+(compatible;+MSIE+9.0;+Windows+NT+6.1;+MSEXCHMON;+ACTIVEMONITORING)
- 200 0 0 46
2014-03-04 08:52:58 10.1.0.36 GET /owa/auth/15.0.847/scripts/premium/flogon.js &CorrelationID=<empty>;&cafeReqId=62bb4655-3bfa-4e07-aa62-27c93e7e8b4d; 443 - 10.1.0.36 Mozilla/4.0+(compatible;+MSIE+9.0;+Windows+NT+6.1;+MSEXCHMON;+ACTIVEMONITORING)
- 200 0 0 0
2014-03-04 08:52:59 10.1.0.36 POST /owa/auth.owa &CorrelationID=<empty>;&cafeReqId=9d52ec1a-2ee1-4954-85e6-89e7e5df407a; 443 [email protected] 10.1.0.36 Mozilla/4.0+(compatible;+MSIE+9.0;+Windows+NT+6.1;+MSEXCHMON;+ACTIVEMONITORING)
- 302 0 0 812
2014-03-04 08:52:59 ::1 GET /OWA/Calendar/[email protected]/calendar/calendar.html &CorrelationID=<empty>;&cafeReqId=4ea66475-9a47-41a4-81cb-6b569715d0d6; 443 - ::1 AMProbe/Local/ClientAccess - 200 0 0 8859
2014-03-04 08:53:01 10.1.0.36 POST /owa/auth.owa &CorrelationID=<empty>;&cafeReqId=b3db7480-2192-436c-b01d-29d0e528cfec; 443 UseronEX2010 10.1.0.36 Mozilla/4.0+(compatible;+MSIE+7.0;+Windows+NT+6.3;+WOW64;+Trident/7.0;+.NET4.0E;+.NET4.0C) https://OWA.company.com/owa/auth/logon.aspx?replaceCurrent=1&url=https%3a%2f%2fOWA.company.com%2fowa%2f
500 0 0 187
2014-03-04 08:53:04 127.0.0.1 GET /Microsoft-Server-ActiveSync/default.eas &CorrelationID=<empty>;&cafeReqId=2e2a655b-00b9-42ae-8789-1e452e6579c3; 443 [email protected] 127.0.0.1 AMProbe/Local/ClientAccess
- 200 0 0 8265
2014-03-04 08:53:14 10.1.0.36 GET /ecp/ &CorrelationID=<empty>;&cafeReqId=8741886f-b9b1-46f9-8c15-baf35809a12c; 443 [email protected] 10.1.0.36 Mozilla/4.0+(compatible;+MSIE+9.0;+Windows+NT+6.1;+MSEXCHMON;+ACTIVEMONITORING)
- 200 0 0 15265
2014-03-04 08:53:14 127.0.0.1 GET /OWA/auth.owa &CorrelationID=<empty>;&cafeReqId=8ad938fb-f2c3-42bf-8718-da62b122422c; 443 - 127.0.0.1 AMProbe/Local/ClientAccess - 302 0 0 15
HTTPERR LOG :
2014-03-04 08:51:48 10.1.0.36 13937 10.1.0.36 444 HTTP/1.1 RPC_IN_DATA /rpc/rpcproxy.dll?EXCH2013.companyNT.local:6001 400 2 BadRequest MSExchangeRpcProxyAppPool
2014-03-04 08:51:48 fe80::99d1:f542:a4d3:b469%12 13872 fe80::99d1:f542:a4d3:b469%12 444 HTTP/1.1 RPC_IN_DATA /rpc/rpcproxy.dll?EXCH2013.companyNT.local:6001 400 2 BadRequest MSExchangeRpcProxyAppPool
2014-03-04 08:52:25 10.1.0.36 13937 10.1.0.36 444 HTTP/1.1 RPC_IN_DATA /rpc/rpcproxy.dll?EXCH2013.companyNT.local:6001 400 2 Connection_Dropped MSExchangeRpcProxyAppPool
2014-03-04 08:52:25 fe80::99d1:f542:a4d3:b469%12 13872 fe80::99d1:f542:a4d3:b469%12 444 HTTP/1.1 RPC_IN_DATA /rpc/rpcproxy.dll?EXCH2013.companyNT.local:6001 400 2 Connection_Dropped MSExchangeRpcProxyAppPool
2014-03-04 08:52:30 127.0.0.1 14122 127.0.0.1 443 HTTP/1.1 GET /RPC/[email protected] 404 - NotFound -
2014-03-04 08:52:30 ::1%0 14121 ::1%0 443 HTTP/1.1 GET /ecp/ReportingWebService/ 404 - NotFound -
2014-03-04 08:54:42 ::1%0 14117 ::1%0 444 - - - - - Timer_ConnectionIdle -
2014-03-04 08:54:48 10.1.0.36 14211 10.1.0.36 444 HTTP/1.1 RPC_IN_DATA /rpc/rpcproxy.dll?EXCH2013.companyNT.local:6001 400 2 BadRequest MSExchangeRpcProxyAppPool
2014-03-04 08:54:48 fe80::99d1:f542:a4d3:b469%12 14285 fe80::99d1:f542:a4d3:b469%12 444 HTTP/1.1 RPC_IN_DATA /rpc/rpcproxy.dll?EXCH2013.companyNT.local:6001 400 2 BadRequest MSExchangeRpcProxyAppPool
2014-03-04 08:55:35 10.1.0.36 14211 10.1.0.36 444 HTTP/1.1 RPC_IN_DATA /rpc/rpcproxy.dll?EXCH2013.companyNT.local:6001 400 2 Connection_Dropped MSExchangeRpcProxyAppPool
2014-03-04 08:55:35 fe80::99d1:f542:a4d3:b469%12 14285 fe80::99d1:f542:a4d3:b469%12 444 HTTP/1.1 RPC_IN_DATA /rpc/rpcproxy.dll?EXCH2013.companyNT.local:6001 400 2 Connection_Dropped MSExchangeRpcProxyAppPool
Trace login, ok it is xml, so print is..
-Request Summary
Site
1
Process
8232
Failure Reason
STATUS_CODE
Trigger Status
500
Final Status
500
Time Taken
500 msec
Url
http://EXCH2013.companyNT.local:80/powershell?clientApplication=ActiveMonitor;PSVersion=4.0&sessionID=Version_15.0_(Build_846.0)=rJqNiZqNgZuQkpqT0pqH0ZuQkpqTkYvRk5CcnpOBzsbLzsbGyczJyIHPzNDPy9DNz87L38/Gxc/KxcrJ
App Pool
MSExchangePowerShellFrontEndAppPool
Authentication
Kerberos
User from token
companyNT\SM_9c071c4922fd420fb
Activity ID
{8000134C-0001-E300-B63F-84710C7967BB}
-Errors & Warnings
No.↓
Severity
Event
Module Name
157. view trace
Warning
-MODULE_SET_RESPONSE_ERROR_STATUS
ModuleName
ManagedPipelineHandler
Notification
EXECUTE_REQUEST_HANDLER
HttpStatus
500
HttpReason
Request Failed
HttpSubStatus
0
ErrorCode
The operation completed successfully.
(0x0)
ConfigExceptionInfo
ManagedPipelineHandler
See all events for the request -
Exchange 2013 SP1 Object is corrupted and inconsistent state after Lync 2013 Installation
Hi Fellows,
I am facing an issue with Exchange 2013 SP1 (5.0.847.32)
environment. I recently installed Lync 2013 (version: 5.0.8308.0) a week ago and just recently start getting the below error when configuring delegation or modifying the users/groups from Exchange Control Panel:
"The Object <object DN> has been corrupted, and it's in an inconsistent state. The following validation errors happened:
The access control defines the ObjectType <object guid> that can't be resolved.."
I can see some forum threads with same issue (links given below) but unable to find if this is a known issue and how to get it resolved. Need assistance if anyone has faced same and could help me out to figure it.
http://social.technet.microsoft.com/Forums/exchange/en-US/72310530-d1de-4b39-a0fb-1592247df03f/access-control-entry-issue-after-installing-lync-2013-into-the-forest?forum=exchangesvrdeploy
http://www.networksteve.com/exchange/topic.php/Issue_with_exchange_2013_lync_2013_intergration/?TopicId=37192&Posts=2
J.AHi
Usually the affected SID objects are referring to deleted objects.
Use the PsGetSid tool to try to resolve them. -
Exchange 2013 SP1 mailbox role on 2012 R2 and 2012
Hi,
We have a client who were running the following setup:
2 x Exchange 2013 CU2 CAS servers / Win Srv 2012
2 x Exchange 2013 CU2 MBX servers / Win Srv 2012
Active Directory etc, basically everything else, runs on Win Server 2012.
Due to upgrading etc, one of the mailbox servers has been removed. It is to be installed with Ex2013 SP1 with 2012 R2 from scratch, and eventually also upgrade the remaining CAS and MBX srvers with SP1 and 2012 R2.
So my question is..will this present a problem? Is it possible to have one MBX running 2013 CU2 on Server 2012 and one MBX running 2013 SP1 on Server 2012 R2?
I've read that failover clustering service is not possible between 2012 and 2012 R2, but i'm not sure how this effects Exchange.
Thanks for your time.Hi,
Each member of the DAG should be running the same operating system. It is not supported to run a DAG member on Windows Server 2012 R2 and run another member on Windows Server 2012.
What's more, upgrading the OS is not supported on Exchange server.
Here are some helpful threads for your reference.
Planning for High Availability and Site Resilience
http://technet.microsoft.com/en-us/library/dd638104(v=exchg.150).aspx
Exchange 2013 CU2 and Upgrading from Server 2012 to Server 2012 R2 issues
http://social.technet.microsoft.com/Forums/exchange/en-US/afba40de-efb6-4916-ae42-b09cff35e5d7/exchange-2013-cu2-and-upgrading-from-server-2012-to-server-2012-r2-issues
Hope it helps.
Best regards,
If you have feedback for TechNet Subscriber Support, contact
[email protected]
Amy Wang
TechNet Community Support -
Migrate to Windows 2012 R2 and Exchange 2013 SP1 using database portability
Hi, I'm planning to migrate from Exchange 2013 SP1 running on Windows 2012 to Exchange 2013 SP1 on Windows 2012 R2.
Is it possible to use database portability to move the databases from the exchange installation on win 2012 to the new installation on Win 2012 R2? This would save a great deal of time not doing the mailbox moves.
I've searched similar cases but couldn't find any, all speak about disaster recovery and database portability but I've found no articles that uses the migration scenario.
Would it be possible to do and if so, what would the steps be? Do I need to delete the database from the source server, move the database files to the new server and mount them and relocate the mailboxes? Or should I dismount the database on the source server,
move them to the new server and mount them and relocate the mailboxes?
Frank.Hi,
According to your description, I recommend you consider using DAG to achieve your requirement.
The following steps for your reference:
1.Prepare a new server which installed windows 2012 R2 for Exchange 2013 mailbox server.
2.After you deploy Exchange 2013 Mailbox servers, you can create a DAG, add Mailbox servers to the DAG, and then replicate mailbox databases between the DAG members.
3.After replication, you can mount all the databases on the new server.
Hope this helps!
Thanks.
Niko Cheng
TechNet Community Support
This no way a resolution. This won't work at all as Both OS will be different and you can't form the Cluster.
Please Unmark it!
Cheers,
Gulab Prasad
Technology Consultant
Blog:
http://www.exchangeranger.com Twitter:
LinkedIn:
Check out CodeTwo’s tools for Exchange admins
Note: Posts are provided “AS IS” without warranty of any kind, either expressed or implied, including but not limited to the implied warranties of merchantability and/or fitness for a particular purpose. -
Exchange 2013 SP1 displaying users that no longer exist
I'm currently in the process of migrating my Exchange 2010 SP3 environment over to 2013 SP1 and am hoping someone can give me a hand with an issue I'm having in Exchange 2013. After installation of 2013 with no errors returned, when I log in to the
admin console I'm seeing users that have been deleted from my AD for quite some time with a mailbox type of "Legacy". I've searched high and low to find these accounts and cannot find them anywhere. I've searched through ADSI Edit and
LDP and nothing. If I click on any of these users and choose to edit I get this error message:
The operation couldn't be performed because object 'GUID' couldn't be found on 'domain controller'.
The odd thing to me is that these "Legacy" users are nowhere to be found on my Exchange 2010 server.
Anyone have any other ideas of how and where I may be able to find these users?Below powershell script can help you find out the lingering objects in your AD.
$myForest = [System.DirectoryServices.ActiveDirectory.Forest]::GetCurrentForest()
$dclist = $myforest.Sites | % { $_.Servers } |% { $_.Name }
$dcs_guid = get-qadobject -searchroot 'CN=Sites,CN=Configuration,DC=domain,DC=root' -Type nTDSDSA -IncludedProperties guid,dn -DontUseDefaultIncludedProperties | % {@{GUID=$_.guid;DN=$_.dn}}
foreach ($dcforestname in $dclist){
foreach ($dc_src_guid in $dcs_guid){
$hostname = ((($dc_src_guid.DN).split(',')[1]).split('=')[1]).tostring()
$dcfqdn = $dclist -like "$hostname*" | Out-String -Stream
$dclist_arr = ($dcfqdn).split(".")
$dcname = $dclist_arr[0]
$dcdomain = $dclist_arr[1 .. ($dclist_arr.count-1)]
$domain_dn = ""
for ($x = 0; $x -lt $dcdomain.Length ; $x++){
if ($x -eq ($dcdomain.Length - 1)){$Separator = ""}else{$Separator =","}
[string]$domain_dn += "DC=" + $dcdomain[$x] + $Separator
write-Host "repadmin /removelingeringobjects $dcforestname" $dc_src_guid.GUID $domain_dn "/advisory_mode >> lingering_debug.log"
Regards, Riaz Javed Butt Consultant Microsoft Professional Services MCITP, MCITP (Exchange), MCSE: Messaging, MCITP Office 365
Maybe you are looking for
-
Vibrate / Silent function has a mind of it's own!
Hi guys and gals, OK so I've signed up as I've just discovered a fault with my iPhone3 3GS, done a bit of googling and found others have had the same problem, wanted to see what you guys thought of it. I bought the phone August 2009 brand new. After
-
Using parameters in a select query sometimes not working
I use parameters throughout my code - usually without problem, but for some reason in one case it does not return a result. When I modify the querystring to contain the value instead of using parameters it works. Is it because I'm secting a clob? or
-
I am trying to understand how asset transfer works to PCA. For vendor and customer line items, I understand open items are transferred to PCA using 1KEK. For assets, there are no open items. So, I am thinking month end asset balances are transferre
-
Which is the Best wireless card for the MacBook Pro with Snow Leopard?
I have the Option GT Ultra Express on AT&T, but ever since I upgraded to snow leopard every update has been messing it up and I'm more than done with this card, Ill even switch carriers if I have to, what cards are the best to use? and who has been h
-
Item level update security in MS SharePoint 2007
Hi, I am working on a requirement where restriction to update list items need to be made at row level. E.g. based on the data in the column of a row, the row will be available for editing to some users. I am looking for an approach to implement this