Exchange 2013 SP1 - Edge Tranport Role

Hi.
When Exchange 2013 was released only CAS & Mailbox roles where available. Hub & Edge Transport server roles were discontinued.
Now with Exchange 2013 SP1, the edge transport role has came back.
Question:
1. Can I deploy a new Exchange 2013 Infrastructure without the Edge Transport Role. This will be a fresh deployment.
I plan to have a UTM with spam blocking at the perimeter instead of the Edge Server?
2. will there any be problems without an Edge Transport ?
Thanks,
Paul

Hi ,
Please find the below mentioned points .
1. Can I deploy a new Exchange 2013 Infrastructure without the Edge Transport Role. This will be a fresh deployment.
I plan to have a UTM with spam blocking at the perimeter instead of the Edge Server?
Answer :
Just ensure that the product is having all the features as you need on your side .There is not necessary to have a an edge server in all the exchange environment's. Moreover Gateway and anti spam products will differ as per the company requirements.
2. will there any be problems without an Edge Transport ?
Answer :
If you are having any one the anti spamming solution to have all the emails scanned before it reaches the exchange server then it will be good .
Just ensure that the anti spamming product what you are going to use is mainly doing the reverse dns lookup
and spf look up .With the help of that we can able to avoid large no of forged emails.
Regards
S.Nithyanandham

Similar Messages

Exchange 2013 SP1 EDGE role content filtering ?

Hello,
Have Exchange 2013 SP1 with CU5 with antispam enabled on mailbox role server. And i wonder if i deploy 2013 Edge role, will i get more granular content filter control, like there is in Office 365? For example: i want to treat empty messages as not
spam.
I have read that control of Edge server is done ONLY by powershell. So if edge role is deployed, still there is no content filter control in ECP (like in office365) ??

Hi,
The Content Filter agent assigns a spam confidence level (SCL) rating to each message. The SCL rating is a number between 0 and 9. A higher SCL rating indicates that a message is more likely to be spam.
Based on my knowledge, I'm afraid we can't filter the empty messages and treat them as not spam.
Here is an article about content filtering in Exchange 2013 for your reference.
Content Filtering
http://technet.microsoft.com/en-us/library/bb124739(v=exchg.150).aspx
Best regards,
If you have feedback for TechNet Subscriber Support, contact
[email protected]
Belinda Ma
TechNet Community Support

Exchange 2013 SP1 Edge Transport Compatability

Exchange 2013 CU3 CAS & MBX are on Windows 2012
I would like to use a Exchange 2013 CU5 as an Edge Transport on a separate server running Windows 2012 R2.
Is this compatible?

Yes.
http://technet.microsoft.com/en-us/library/ff728623(v=exchg.150).aspx
Exchange Server Supportability Matrix
Twitter!: Please Note: My Posts are provided “AS IS” without warranty of any kind, either expressed or implied.

Exchange 2013 SP1 Installation Errors I Cannot Resolve

Good Afternoon All -
Note: I updated this post an hour after posting. Still no solution, but please see updated info at end of this post)
I'm trying to introduce Exchange into an existing, small environment. The server I'm trying to install it onto is an SBS 2011 server (single server.) Even though SBS comes with Exchange, I found out that it's installation was corrupted and someone
had attempted to uninstall it before. Yes, it's being installed onto a server with a DC. I considered creating a Hyper-V VM on the server for Exchange, but thought it may be better to try to install directly onto server instead.
Before I started, I made sure all Exchange data had been removed. I checked for and deleted (if present) all Exchange-related objects in ADSI, ADU&C, files, and registry entries.
When I try to install Exchange 2013 SP1, I get the below errors. I know that some are easily resolved by installing pre-requisites - however - others aren't - especially the pending reboot one. I've restarted the server many times when making
changes or applying various updates and still get flagged to restart during installation. I've tried the SBS 2011 repair disc as well, but had many issues with it. In all honesty, the whole server needs to be wiped and re-installed, but
cannot do at this point.
Besides the errors below, I've zipped up the ExchangeSetupLogs folder and placed them in the link below. Also below are system specs. The only edit I made in them is a find/replace for server and domain name.
ExchangeSetupLogs Folder
System Specs
Xeon E31270 3.4Ghz
16gb RAM
Windows Server 2011 SBS x64 (Domain Controller Role Installed & Used)
C:\ - RAID 1 = 500gb
D:\ - SATA HDD = 320gb
E:\ - SATA HDD = 320GB
Should I perhaps try to install to a VM on the server or think that would use too many unnecessary resources?
Any help would be appreciated - Thanks!
Error:
This computer requires the update described in Microsoft Knowledge Base article KB2619234 (http://go.microsoft.com/fwlink/?LinkId=262359).
Without this update, the Outlook Anywhere feature may not work reliably.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.Win7RpcHttpAssocCookieGuidUpdateNotInstalled.aspx
Error:
There is a pending reboot from a previous installation of a Windows Server role or feature. Please restart the computer and then
run Setup again.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.PendingRebootWindowsComponents.aspx
Error:
The Windows component RSAT-Clustering isn't installed on this computer and needs to be installed before Exchange Setup can begin.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.RsatClusteringInstalled.aspx
Error:
This computer requires the Microsoft Unified Communications Managed API 4.0, Core Runtime 64-bit. Please install the software from
http://go.microsoft.com/fwlink/?LinkId=260990.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.UcmaRedistMsi.aspx
Error:
An unsupported operating system was detected. Exchange Server 2013 Client Access, Mailbox, and Edge Transport server roles support
Windows Server 2008 R2 SP1 or later and Windows Server 2012.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.ValidOSVersion.aspx
Warning:
Installing Exchange Server on a domain controller will elevate the permissions for Exchange Trusted Subsystem to domain administrators.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.WarningInstallExchangeRolesOnDomainController.aspx
Warning:
Setup will prepare the organization for Exchange 2013 by using 'Setup /PrepareAD'. No Exchange 2007 server roles have been detected
in this topology. After this operation, you will not be able to install any Exchange 2007 servers.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.NoE12ServerWarning.aspx
Warning:
Setup will prepare the organization for Exchange 2013 by using 'Setup /PrepareAD'. No Exchange 2010 server roles have been detected
in this topology. After this operation, you will not be able to install any Exchange 2010 servers.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.NoE14ServerWarning.aspx
Ben K.
UPDATE
I just tried fixing a few things and tried again. Still no luck. Below is what I changed as well as the errors received. Only option was Retry. Can I just not install it onto this environment?
What I Changed
Installed Unified Comm Managed API 4.0 (Required Uninstalling Speech Analysis app before it would install)
Installed KB2619234 for Outlook Anywhere
Installed 12 updates - Server fully patched
Exchange Setup Errors
Error:
An unsupported operating system was detected. Exchange Server 2013 Client Access, Mailbox, and Edge Transport server roles support
Windows Server 2008 R2 SP1 or later and Windows Server 2012.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.ValidOSVersion.aspx
Warning:
Installing Exchange Server on a domain controller will elevate the permissions for Exchange Trusted Subsystem to domain administrators.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.WarningInstallExchangeRolesOnDomainController.aspx
Warning:
Setup will prepare the organization for Exchange 2013 by using 'Setup /PrepareAD'. No Exchange 2007 server roles have been detected
in this topology. After this operation, you will not be able to install any Exchange 2007 servers.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.NoE12ServerWarning.aspx
Warning:
Setup will prepare the organization for Exchange 2013 by using 'Setup /PrepareAD'. No Exchange 2010 server roles have been detected
in this topology. After this operation, you will not be able to install any Exchange 2010 servers.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.NoE14ServerWarning.aspx
Thanks Guys -

Hi,
Agree. Windows Server 2011 SBS x64 can be the problem.
Thanks,
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact
[email protected]
Simon Wu
TechNet Community Support

What happend New-MailboxExportRequest cmdlet in exchange 2013 SP1 is missing?

Cmdlet New-MailboxExportRequest is not recognize cmdlet in Exchange 2013 SP1
How can i do export mailbox to pst file in exchange 2013 SP1?

You might be facing this issue because of not having the rights to execute the New-MailboxExportRequest CMDLET.
Follow the steps given below in order to export the mailboxes into PST file
1. Open the Exchange Console and run:
New-ManagementRoleAssignment -Name "Import Export PST" -SecurityGroup "Organization Management" -Role “Mailbox Import Export"
This will generate a new role group called Import Export PST to the Oranization Management group with the role Mailbox Import Export.
You should Close and Restart the Exchange Management System again so that the changes made will get reflected in the settings, otherwise you will still get the same erroriIf not
restarted. Now move to the next steps.
2. Assign “Mailbox Import Export” role to it.
3. Add Desired Users to Role Group
4. Create Network Share ( Exchange Trusted Subsystem group has read/write permission to NTFS Permissions)
5. Run PS New-MailboxExportRequest
6. Monitor New-MailboxExportRequest
Verify PST File has been created on the network Share and you are done.
If you get the same error again, then there will be some hardware or software issues due to which you are not able to export mailboxes into PST files. In that case, you can make
use of any third party tool like Stellar Phoenix EDB To PST converter, which will help you to export your exchange database files to PST files easily and quickly. You can try this software by downloading its demo directly from their site http://www.stellarinfo.com/email-repair/edb-pst-converter.php

Exchange 2013 SP1 setup fails at prerequisite Analysis

I installed a completely new server network with Hyper-v 2012R2
I installed two virtual 2012R2 servers: DC01 as the Domain Controller of "testdomain.local" and EX01 as the Exchange server.
EX01 is joined the domain "testdomain" from DC01
I log in on EX01 with an in AD created testdomain\exadmin account who is member of domain admins, enterprise admins, schema admins, administrators and group policy creator owners.
I have run the command Install-WindowsFeature AS-HTTP-Activation, Desktop-Experience,
NET-Framework-45-Features, RPC-over-HTTP-proxy, RSAT-Clustering, RSAT-Clustering-CmdInterface, RSAT-Clustering-Mgmt, RSAT-Clustering-PowerShell, Web-Mgmt-Console, WAS-Process-Model, Web-Asp-Net45, Web-Basic-Auth, Web-Client-Auth, Web-Digest-Auth, Web-Dir-Browsing,
Web-Dyn-Compression, Web-Http-Errors, Web-Http-Logging, Web-Http-Redirect, Web-Http-Tracing, Web-ISAPI-Ext, Web-ISAPI-Filter, Web-Lgcy-Mgmt-Console, Web-Metabase, Web-Mgmt-Console, Web-Mgmt-Service, Web-Net-Ext45, Web-Request-Monitor, Web-Server, Web-Stat-Compression,
Web-Static-Content, Web-Windows-Auth, Web-WMI, Windows-Identity-Foundation, Telnet-Client, RSAT-ADDS
on EX01
I have installed the Microsoft Unified Communications Managed API 4.0
Then I run the Exchange 2013 SP1 setup and the prerequisite check gives the following errors:
Error:
You must be a member of the 'Organization Management' role group or a member of the 'Enterprise Admins' group to continue.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.GlobalServerInstall.aspx
Error:
You must use an account that's a member of the Organization Management role group to install or upgrade the first Mailbox server role in the topology.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.DelegatedBridgeheadFirstInstall.aspx
Error:
You must use an account that's a member of the Organization Management role group to install the first Client Access server role in the topology.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.DelegatedCafeFirstInstall.aspx
Error:
You must use an account that's a member of the Organization Management role group to install the first Client Access server role in the topology.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.DelegatedFrontendTransportFirstInstall.aspx
Error:
You must use an account that's a member of the Organization Management role group to install or upgrade the first Mailbox server role in the topology.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.DelegatedMailboxFirstInstall.aspx
Error:
You must use an account that's a member of the Organization Management role group to install or upgrade the first Client Access server role in the topology.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.DelegatedClientAccessFirstInstall.aspx
Error:
You must use an account that's a member of the Organization Management role group to install the first Mailbox server role in the topology.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.DelegatedUnifiedMessagingFirstInstall.aspx
Error:
Setup encountered a problem while validating the state of Active Directory: Active Directory server is not available. Error message: Active directory response: The LDAP server is unavailable. See the Exchange setup log for more information on this
error.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.AdInitErrorRule.aspx
Error:
Either Active Directory doesn't exist, or it can't be contacted.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.CannotAccessAD.aspx
I can connect with the Active Directory Sites and Domains and other applets to the AD. So Why these errors???
HELP!
Regards, Manu
Manu van Winkel

Hi, thanks for the answer.
I restarted the server and did the "run as administrator": same result.
The first errormessage in the exchangesetup.log is:
[ERROR] Setup encountered a problem while validating the state of Active Directory: Active Directory server is not available. Error message: Active directory response: The LDAP server is unavailable. See the Exchange setup log for more information
on this error.
When I run dcdiag /s:DC01 from EX01 it passes all tests except:
DFSREvent "The RPC server is unavailable"
KccEvent "The RPC server is unavailable."
SystemLog "The RPC server is unavailable."
Could these be of any influence?
Running dcdiag on DC01 passes all tests.
The only thing I changed after setting up DC01, was changing the fixed IP-adres from 192.168.25.3 to 192.168.25.2, but I ran ipconfig /flushdns and ipconfig /registerdns and dcdiag /fix afterwards.
The only roles installed on DC01 are AD DS (I tried installing exchange before and after adding the AD DS role), AD, DNS, DHCP and Fileservices
I don't know where to look anymore....
Manu van Winkel

Exchange 2013 SP1 | Another HTTP 500.0.0 Error

Help!
We are in the middle of migrating from Exchange 2010 SP3 to Exchange 2013 SP1 and we are being plagued with HTTP 500 errors on every Exchange 2013 server now.
I have two Client Access servers installed (EXCHFE01 & EXCHFE02) and one backend mailbox server (EXCHMB03) with the Client Access role also installed (for troubleshooting purposes). Once I get everything working I'll install two backend 2013 servers
with the mailbox role only for production (load-balanced, clustered, etc). I still have two Exchange 2010 mailbox servers left since one has a single large mailbox left on it and the other hosts public folders. I'll get to migrating those later. All Exchange
2013 servers are running Windows Server 2012. All are on the same LAN and no firewalls are between them.
On all three 2013 servers (EXCHFE01, EXCHFE02, EXCHMB03) I'm getting the dreaded HTTP 500 error whether I try to get to OWA or ECP. This did work at one point where I could at least login to the mailbox server (EXCHMB03) and migrate all my mailboxes over
to it. Sometime this morning after the two Client Access servers were installed the mailbox server stopped working (HTTP 500 errors). This is very frustrating because I can't even login to a console to manage Exchange from any server at this point.
Both Client Access servers aren't really showing anything of value in the event logs or the IIS logs. The mailbox server (EXCHMB03) does show the following event 3002:
Protocol /Microsoft-Server-ActiveSync failed to process request from identity NT AUTHORITY\SYSTEM. Exception: Microsoft.Exchange.Security.Authentication.BackendRehydrationException: Rehydration failed. Reason: Source server 'NT AUTHORITY\SYSTEM' does not have token serialization permission.
at Microsoft.Exchange.Security.Authentication.BackendRehydrationModule.ProcessRequest(HttpContext httpContext)
at Microsoft.Exchange.Security.Authentication.BackendRehydrationModule.OnAuthenticateRequest(Object source, EventArgs args).
...and I get the following when I run the Exchange Management Shell tool on the same mailbox server (along with lots of other red HTML text):
More Information:
This error means that there was a problem while processing the request. The request was received by the Web server, but during processing a fatal error occurred, causing the 500 error.
The Client Access servers show the following errors:
Performance counter updating error. Counter name is Location cache update time, category name is MSExchange Active Manager Client. Optional code: 3. Exception: The exception thrown is : System.InvalidOperationException: The requested Performance Counter is not a custom counter, it has to be initialized as ReadOnly.
at System.Diagnostics.PerformanceCounter.InitializeImpl()
at System.Diagnostics.PerformanceCounter.set_RawValue(Int64 value)
at Microsoft.Exchange.Diagnostics.ExPerformanceCounter.set_RawValue(Int64 value)
Last worker process info : System.ArgumentException: Process with an Id of 4040 is not running.
at System.Diagnostics.Process.GetProcessById(Int32 processId)
at Microsoft.Exchange.Diagnostics.ExPerformanceCounter.GetLastWorkerProcessInfo()
Processes running while Performance counter failed to update:
888 svchost
264 smss
532 conhost
2576 Microsoft.Exchange.UM.CallRouter
1596 WMSvc
3932 dllhost
4020 svchost
2308 dwm
5060 taskhostex
844 svchost
1972 Microsoft.Exchange.Directory.TopologyService
1228 inetinfo
1316 vmtoolsd
3896 svchost
780 svchost
1580 rundll32
1668 mqsvc
816 dwm
3840 slui
3532 rdpclip
3980 WmiPrvSE
4200 SppExtComObj
4288 winlogon
2140 SMSvcHost
676 svchost
1564 svchost
1296 Microsoft.Exchange.Diagnostics.Service
1472 Microsoft.Exchange.ServiceHost
1204 svchost
1292 ServerManagerLauncher
488 winlogon
664 svchost
572 lsass
3236 dllhost
2972 WmiPrvSE
4484 w3wp
388 csrss
1600 rundll32
564 services
1260 msdtc
5032 sppsvc
1448 MSExchangeHMHost
824 LogonUI
4204 VSSVC
2524 userinit
2700 MSExchangeFrontendTransport
1708 SMSvcHost
728 svchost
460 wininit
904 svchost
992 svchost
4996 TSTheme
4240 slui
4904 taskhost
452 csrss
4340 csrss
4 System
1164 spoolsv
1988 slClient
2760 MSExchangeHMWorker
0 Idle
Performance Counters Layout information: FileMappingNotFoundException for category MSExchange Active Manager Client : Microsoft.Exchange.Diagnostics.FileMappingNotFoundException: Cound not open File mapping for name Global\netfxcustomperfcounters.1.0msexchange active manager client. Error Details: 2
at Microsoft.Exchange.Diagnostics.FileMapping.OpenFileMapping(String name, Boolean writable)
at Microsoft.Exchange.Diagnostics.PerformanceCounterMemoryMappedFile.Initialize(String fileMappingName, Boolean writable)
at Microsoft.Exchange.Diagnostics.ExPerformanceCounter.GetAllInstancesLayout(String categoryName)
... and...
A transient failure has occurred. The problem may resolve itself. Diagnostic information:
Microsoft.Exchange.Data.DataSourceOperationException: The request failed. The remote server returned an error: (503) Server Unavailable. ---> Microsoft.Exchange.WebServices.Data.ServiceRequestException: The request failed. The remote server returned an error: (503) Server Unavailable. ---> System.Net.WebException: The remote server returned an error: (503) Server Unavailable.
at System.Net.HttpWebRequest.GetResponse()
at Microsoft.Exchange.WebServices.Data.EwsHttpWebRequest.Microsoft.Exchange.WebServices.Data.IEwsHttpWebRequest.GetResponse()
at Microsoft.Exchange.WebServices.Data.ServiceRequestBase.GetEwsHttpWebResponse(IEwsHttpWebRequest request)
--- End of inner exception stack trace ---
at Microsoft.Exchange.WebServices.Data.ServiceRequestBase.GetEwsHttpWebResponse(IEwsHttpWebRequest request)
at Microsoft.Exchange.WebServices.Data.ServiceRequestBase.ValidateAndEmitRequest(IEwsHttpWebRequest& request)
at Microsoft.Exchange.WebServices.Data.ExchangeService.InternalFindFolders(IEnumerable`1 parentFolderIds, SearchFilter searchFilter, FolderView view, ServiceErrorHandling errorHandlingMode)
at Microsoft.Exchange.WebServices.Data.ExchangeService.FindFolders(FolderId parentFolderId, SearchFilter searchFilter, FolderView view)
at Microsoft.Exchange.Data.Storage.Management.EwsStoreDataProvider.InvokeServiceCall[T](Func`1 callback)
--- End of inner exception stack trace ---
at Microsoft.Exchange.Data.Storage.Management.EwsStoreDataProvider.InvokeServiceCall[T](Func`1 callback)
at Microsoft.Exchange.Data.Storage.Management.EwsStoreDataProvider.GetOrCreateFolderCore(String folderName, FolderId parentFolder, Func`1 creator)
at Microsoft.Exchange.Data.Storage.Management.AsyncOperationNotificationDataProvider.GetDefaultFolder()
at Microsoft.Exchange.Data.Storage.Management.EwsStoreDataProvider.<>c__DisplayClass1b`1.<InternalFindPaged>b__13()
at Microsoft.Exchange.Data.Storage.Management.EwsStoreDataProvider.InvokeServiceCall[T](Func`1 callback)
at Microsoft.Exchange.Data.Storage.Management.EwsStoreDataProvider.<InternalFindPaged>d__21`1.MoveNext()
at Microsoft.Exchange.Data.Storage.Management.AsyncOperationNotificationDataProvider.<GetNotificationDetails>d__4.MoveNext()
at System.Linq.Enumerable.WhereEnumerableIterator`1.MoveNext()
at Microsoft.Exchange.Servicelets.CertificateNotificationServicelet.RemoveAllNotification()
at Microsoft.Exchange.Servicelets.CertificateNotificationServicelet.UpdateDataInMbx(List`1 certificates)
at Microsoft.Exchange.Servicelets.CertificateNotificationServicelet.Work()
I've tried all sorts of recommended fixes but none have worked so far:
ADSIEdit and remove msExchCanaryData0 data
Reinstall Exchange multiple times
Rebooted multiple times
This article: http://social.technet.microsoft.com/Forums/exchange/en-US/08d3777c-dc03-4411-8c87-7db37d2f406a/exchange-2013-owa-login-error-http-500?forum=exchangesvrclients
Rebooted DCs multiple times (no exchange servers are DCs)
I'm sure I've left out a few troubleshooting steps since I've been working at this for two days. Can anybody offer any advice? I'm at my wits end here...

Hi,
Please check whether the mail.mydomain.com is pointed to your Exchange 2010 or Exchange 2013. Please run the following command to check your OWA virtual directores and ECP virtual directories:
Get-OwaVirtualDirectory -ShowMailboxVirtualDirectories | Select Identity,name,Internalurl,ExternalUrl,*auth*
Get-EcpVirtualDirectory -ShowMailboxVirtualDirectories | Select Identity,name,Internalurl,ExternalUrl,*auth*
In IIS manager > Default Web Site, please make sure Anonymous Authentication is Enabled in Authentication. Confirm that "Require SSL" is checked on the SSL Settings of the default web site.
Regards,
Winnie Liang
TechNet Community Support

Exchange 2013 SP1 readiness check failing

Trying to install our first Exchange 2013 SP1 server on Windows 2012 R2 in our datacentre, the readiness check fails with:
Error:
The Active Directory schema isn't up-to-date, and this user account isn't a member of the 'Schema Admins' and/or 'Enterprise Admins' groups.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.SchemaUpdateRequired.aspx
There are many more errors relating to Enterprise admin rights etc.
Please note that:
My account is Domain admin, Schema admin and Enterprise admin member, it always has been.
I tried the built-in AD Administrator which of course is part of the groups as well, no difference.
Active Directory is at 2008 R2 for domain and forest functional levels.
I tried rejoining the new Exchange designated server to the domain
I've installed RSAT-ADDS, the Managed API 4.0 and all the other windows roles via powershell
There is a local domain controller that is a global catalog server on the new Exchange server subnet
I tried running the Exchange Setup on a different server on the same subnet as where the active 2010 Exchange server resides as well as the FSMO AD role holder resides, this works fine. I even did the AD prep from there no problem, that made no difference
on the datacentre server
AD replicates fine between the FSMO role holder and the Datacentre (no errors in dcdiag or repadmin /showrepl)
This error is in the event log:
The description for Event ID 4027 from source MSExchange ADAccess cannot be found. Either the component that raises this event is not installed on your local computer or the installation is corrupted. You can install or repair the component on the local computer.
If the event originated on another computer, the display information had to be saved with the event.
The following information was included with the event:
ExSetupUI.exe
6724
Get Servers for domain.local
TopologyClientTcpEndpoint (localhost)
3
System.ServiceModel.EndpointNotFoundException: Could not connect to net.tcp://localhost:890/Microsoft.Exchange.Directory.TopologyService. The connection attempt lasted for a time span of 00:00:02.0475315. TCP error code 10061: No connection could be made because the target machine actively refused it 127.0.0.1:890. ---> System.Net.Sockets.SocketException: No connection could be made because the target machine actively refused it 127.0.0.1:890
at System.Net.Sockets.Socket.DoConnect(EndPoint endPointSnapshot, SocketAddress socketAddress)
at System.Net.Sockets.Socket.Connect(EndPoint remoteEP)
at System.ServiceModel.Channels.SocketConnectionInitiator.Connect(Uri uri, TimeSpan timeout)
--- End of inner exception stack trace ---
Server stack trace:
at System.ServiceModel.Channels.SocketConnectionInitiator.Connect(Uri uri, TimeSpan timeout)
at System.ServiceModel.Channels.BufferedConnectionInitiator.Connect(Uri uri, TimeSpan timeout)
at System.ServiceModel.Channels.ConnectionPoolHelper.EstablishConnection(TimeSpan timeout)
at System.ServiceModel.Channels.ClientFramingDuplexSessionChannel.OnOpen(TimeSpan timeout)
at System.ServiceModel.Channels.CommunicationObject.Open(TimeSpan timeout)
at System.ServiceModel.Channels.ServiceChannel.OnOpen(TimeSpan timeout)
at System.ServiceModel.Channels.CommunicationObject.Open(TimeSpan timeout)
Exception rethrown at [0]:
at System.Runtime.Remoting.Proxies.RealProxy.HandleReturnMessage(IMessage reqMsg, IMessage retMsg)
at System.Runtime.Remoting.Proxies.RealProxy.PrivateInvoke(MessageData& msgData, Int32 type)
at System.ServiceModel.ICommunicationObject.Open()
at Microsoft.Exchange.Net.ServiceProxyPool`1.GetClient(Boolean useCache)
at Microsoft.Exchange.Net.ServiceProxyPool`1.TryCallServiceWithRetry(Action`1 action, String debugMessage, WCFConnectionStateTuple proxyToUse, Int32 numberOfRetries, Boolean doNotReturnProxyOnSuccess, Exception& exception)
the message resource is present but the message is not found in the string/message table

So I decided to re-install the OS, worked perfectly now. Only difference from before would be:
SCCM hasn't pushed SCEP 2012 to the new build of the same server yet
The original server was installed in a different AD site and then it was physically mode and reassigned to an new AD site and subnet
I might have installed the pre-reqs in a slightly different order (RSAT-ADDS, all the IIS etc things via powershell
and then the UCM API 4.0. (saw few comments that the order of how you install them matters in other forums).
10 or so Microsoft Windows updates haven't installed on the new OS build yet.
Other than that, its identical. But if its not broken don't fix it, perhaps the above can help someone else though.

Exchange 2013 sp1 move databases

Hello all
I am running Exchange 2013 sp1 in a two node DAG. Originally the DAG had two under powered servers, i built two new more powerful servers added the servers to the DAG, then i moved database copies to the new servers, removed the copies from the original
servers and then removed the original servers from the DAG. The two original servers are multi role (CAS Mailbox) and currently they are still in the org. My confusion is around this. When i run get-mailbox -identity <name>. The output from the command
shows the mailbox is on oldserver. Again oldserver was removed from the DAG and no databases exist on the server. I want to remove the two old servers from the org, but i am hesitant on doing this because all mailboxes seem to think they exist on oldserver
Thanks for any help
Bulls on Parade

You can ignore that:
http://blogs.technet.com/b/timmcmic/archive/2011/09/26/exchange-2010-homemta-and-msexchhomeservername-are-not-updated-on-mailboxes.aspx
Twitter!: Please Note: My Posts are provided “AS IS” without warranty of any kind, either expressed or implied.

Exchange 2013 SP1 Not Receiving e-mail

Hello,
Mail flow between Exchange 2010 sp3 & Exchange 2013 SP1 (update Cu5) not working.
Exchange 2013 setup is Exchange 2013 sp1 DVD
Exchange 2010 when sending mail to external it's ok.
Exchange 2010 when sending mail to exchange 2010 users it's ok.
Exchange 2013 when sending mail to External it's ok.
Exchange 2013 when sending mail to exchange 2010 users it's ok.
or
Exchange 2010 when sending mail to exchange 2013 not working
Exchange 2013 when sending mail to Exchange 2013 not working
From internet --> SMTP GW (exh edge) --> Exchange 2010 it's ok
From Internet --> SMTP GW (exh edge) --> Exchange 2013 not working.
organization;
1 AD site and 1 PDC (2012 R2) + 3 DC (1x 2008 R2 + 2 x 2003 Server) (Windows Server 2003 domain fl)
With Exchange 2010 exchange 2013 on the same subnet. Exchange 2010 physical machine, Exchange 2013 physical machine ( eth Microsoft Team Server 2012 R2 )
All server is region setting Turkey
Exchange 2010 error
451 4.7.0 Temporary server error. Please try again later. PRX4
Exchange 2013 error
451 4.4.0 primary target ip address responded with 501 5.5.4 Invalid arguments. attempted failover to alternative host, but that did not succeed. either there are no alternate host, or delivery failed to all alternate hosts. Th
thanks

Hi,
From your description, the Exchange 2013 server can't receive emails internally and externally. I recommend you follow the steps below for troubleshooting:
1. Please restart the Microsoft Exchange Frontend Transport service on CAS and the Microsoft Exchange Transport service on Mailbox and check the result.
2. Please make sure that the authentication on default receive connector is right. Here is the configuration in my environment for your reference:
Hope it helps.
Best regards,
If you have feedback for TechNet Subscriber Support, contact
[email protected]
Amy Wang
TechNet Community Support

Exchange 2013 SP1 and CUCM 9.1.2 - Exch not recognizing called extension

I think I'm almost there in getting Exchange 2013 SP1 UM working with CUCM 9.1.2...I've got two issues at the moment that I need a little help with.
1) When I dial my VM pilot (6040) from a UM enabled extension it prompts to enter an extension. When I dial the same extension and let it ring to VM, Exchange picks up and says "the person you are trying to reach does not have a valid voice mail box
on our system".
2) This just started happening this afternoon, when I dial my VM pilot (6040) exch3 picks up as thats what I have my route pattern pointing to. If I enter the extension of a mailbox on exch2, I get stuck in a endless loop.
I've followed this post as a guide but it hasn't resolved my issue.
https://supportforums.cisco.com/discussion/11914031/exchange-2013-um-and-cucm-86
My Exchange environment looks like this:
Site 1:
exch1 - CAS/Mailbox, used for mainly utility type work, journal, dedicated SMTP flows etc
exch2 - CAS/Mailbox, part DAG13
exch3 - CAS/Mailbox, part of DAG13
Site 2:
exch2dr - CAS/Mailbox, part of DAG13
exch3dr - CAS/Mailbox, part of DAG13
DAG13 is stretched between two sites, there are no users at our DR site so CUCM is pointing to Site 1 for UM. Each site has an internet facing CAS-only server for OWA/EAS etc.
Any help is greatly appreciated. I'd love to get rid of Unity.
EDIT:
I just found this event in the event logs:
The Microsoft Exchange Unified Messaging service on the Mailbox server received a diverted call with ID "d51600-3a3140c5-9b8-c1414ac@EXCH3-IPADDR" for extension "4099" on UM dial plan "CUCM" from UM IP gateway "CUCM IP",
but no UM-enabled mailbox for the corresponding extension could be found. Please check the extension and make sure that the corresponding mailbox is enabled for UM and associated with the correct UM dial plan.

9.1.2 I think it is, we upgraded to avoid the known DNS bug
I cant see how to PM you either
The crux of it was outlined below with some tweaks
http://blogs.technet.com/b/canitpro/archive/2014/04/30/step-by-step-integration-between-exchange-2013-um-and-cisco-unified-communication-manager.aspx
As we have multiple combined role servers, our trunks are set up as follows:
1. 1 x CAS Trunk - contains all CAS Servers on port 5060
2. 4 x MBX Trunks - contains Maibox Server with ports 5062-5068
On top of that, we had to Allow "Redirecting Diversion Header Delivery - Inbound (and Outbound)" on the CAS Trunk but DISABLE it on the Mailbox Trunks
Also, make sure that you are using Telephone Extension Dial plans in Exchange 2013 (Despite them being unable to be associated with a 13 Server - EX13 answers for all calls anyway)
Lastly, the MS documentation is a little strange - it says that as your last step of UM migration, you should point your Call Manager to 2013 - I don't agree with that statement, EX13 routes calls back to 2010 UM Servers perfectly fine, so treat it the same
as any other CAS based service - point to 2013, and it will handle the rest

Exchange 2013 sp1 smtp NTLM auth for child domain users

i have exchange organization with exchange 2007 sp 3 & exchange 2013 sp1.
there are all users in Exchange 2013 server (mail flow is through Exchange 2013 server)
i have single forest, 2 site (site1, site2), root domain root.local and 1 child domain ch.root.local
DC for child domain is located in site2 (dc.ch.root.local)
multirole exchange 2013 server is installed in root domain.
i am traing to configure smtp receive connector with NTLM auth and have one problem.
when user in child domain try send email through this receive connector i see in log
<,AUTH NTLM,
>,334 <authentication response>,
*,SMTPSubmit SMTPAcceptAnyRecipient BypassAntiSpam AcceptRoutingHeaders,Set Session Permissions
*,CH\user1,authenticated
*,,Setting up client proxy session failed with error: 535 5.7.3 Unable to proxy authenticated session because either the backend does not support it or failed to resolve the user
*,,"Setting up client proxy session failed with error: 451 4.4.0 Primary target IP address responded with: ""535 5.7.3 Unable to proxy authenticated session because either
the backend does not support it or failed to resolve the user."" Attempted failover to alternate host, but that did not succeed. Either there are no alternate hosts, or delivery failed to all alternate hosts. The last endpoint attempted was 192.168.1.15:465"
but authentication is succesfull for users from root domain.
why do it can be?
Thanks.

thanks for link
at smtp receive logs (Hub transport role) i've found the next:
Client Proxy EXMAIL2013,08D134DAF6CE1C51,49,192.168.1.15:465,
*,NT AUTHORITY\SYSTEM,authenticated
>,235 <authentication response>,
<,XPROXY SID=08D130D354F520D1 IP=192.168.1.21 PORT=57085 DOMAIN=[192.168.1.21] CAPABILITIES=0 SECID=Uy0xxx...
*,,Error while looking up SamAccountName chuser: The user name or password is incorrect.\r\n
*,None,Set Session Permissions
>,250 XProxy accepted but user identity could not be obtained,

Exchange 2013 SP1 Readiness Checks: No Exchange 2007 server detected

Hi there,
We are planning to upgrade our current Exchange 2007 server with the new Exchange 2013 SP1. I have been following Exchange Server Deployment Assistant to assist me with this task. Only schema update (setup /PrepareSchema) had been done so
far. I didn’t run setup /PrepareAD command manually because I wasn’t sure if I need to provide ‘Organisation Name’ with it or not?! I have installed all of the prerequisites as noted in the Microsoft documentation.
Now, I am a bit confuse with the ‘Readiness Checks’ page during graphical user installation of Exchange 2013 SP1 setup on Windows 2012 R2. Windows 2012 R2 server has all available updates applied.
===
Warning:
Setup will prepare the organization for Exchange 2013 by using 'Setup /PrepareAD'. No Exchange 2010 server roles have been detected in this topology. After this operation, you will not be able to install any Exchange 2010 servers.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.NoE14ServerWarning.aspx
===
I get the message why setup wants to run preparation for the Ex2013 with the ‘Setup /PrepareAD’. But, why ‘No Exchange 2010 server role have been detected in this topology’?! Ok, in my case setup doesn’t detect Exchange 2007 server. Is that ok to proceed
with the installation or something else needs to be done first?
Thanks in advance.

I need Exchange guru advice here please. Since we already have Exchange 2007 SP3 RU 10 in our Windows 2008R2 Active Directory domain here I need to be 100% confident that pushing Exchange 2013 SP1 “Install” will not override our existing Ex2007 environment.
That would be a huge disaster!
Microsoft is saying that: “Microsoft Exchange Server 2013 Setup displayed this warning because
no Exchange Server 2010 or Exchange Server 2007 server roles exist in the organization.”
http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.NoE14ServerWarning.aspx
Ok, I get the message about if I continue with Exchange Server 2013 installation, I won’t be able to add Exchange 2010 or Exchange 2007 servers to the organization at a future date..., and why would I need to do that anyway?!
Microsoft wording about “some solutions may require the use...” are very confusing since we will require to consider “Coexistence or migration requirements"
Perhaps, before running Exchange 2013 SP1 setup I need to run setup for preparing AD without “Organisation Name” parameter?! Something like this:
setup /PrepareAD /IAcceptExchangeServerLicenseTerms

Error in moving exchange 2010 mailboxes to Exchange 2013 SP1 during migration

Dear All,
We were running Exchange 2010 SP3 with MBX/HT/CAS role in single server. Now we are migrating our exchange 2010 to Exchange 2013 SP1. After configuring co-existence and during the mailbox move from Exchange 2010 to Exchange 2013 SP1, we are facing below
error. Please help to troubleshot. As per our search on net, people were suggesting that it can be due to not able to resolve NetBIOS name. We checked same and we are able to ping both servers by NetBIOS and FQDN names.
[PS] C:\Windows\system32>New-MoveRequest -Identity
'[email protected]' -TargetDatabase "CI-DB01"
MapiExceptionNetworkError: Unable to make connection to the server. (hr=0x80004005, ec=2423)
Diagnostic context:
    Lid: 14744   dwParam: 0x0 Msg: EEInfo: Status: 1722
    Lid: 9624    dwParam: 0x0 Msg: EEInfo: Detection location: 323
    Lid: 13720   dwParam: 0x0 Msg: EEInfo: Flags: 0
    Lid: 11672   dwParam: 0x0 Msg: EEInfo: NumberOfParameters: 0
    Lid: 62184
    Lid: 16280   dwParam: 0x0 Msg: EEInfo: ComputerName: n/a
    Lid: 8600    dwParam: 0x0 Msg: EEInfo: ProcessID: 6004
    Lid: 12696   dwParam: 0x0 Msg: EEInfo: Generation Time: 0414-08-21T09:10:43.8970000Z
    Lid: 10648   dwParam: 0x0 Msg: EEInfo: Generating component: 18
    Lid: 14744   dwParam: 0x0 Msg: EEInfo: Status: 1237
    Lid: 9624    dwParam: 0x0 Msg: EEInfo: Detection location: 313
    Lid: 13720   dwParam: 0x0 Msg: EEInfo: Flags: 0
    Lid: 11672   dwParam: 0x0 Msg: EEInfo: NumberOfParameters: 0
    Lid: 62184
    Lid: 16280   dwParam: 0x0 Msg: EEInfo: ComputerName: n/a
    Lid: 8600    dwParam: 0x0 Msg: EEInfo: ProcessID: 6004
    Lid: 12696   dwParam: 0x0 Msg: EEInfo: Generation Time: 0414-08-21T09:10:43.8970000Z
    Lid: 10648   dwParam: 0x0 Msg: EEInfo: Generating component: 18
    Lid: 14744   dwParam: 0x0 Msg: EEInfo: Status: 10060
    Lid: 9624    dwParam: 0x0 Msg: EEInfo: Detection location: 311
    Lid: 13720   dwParam: 0x0 Msg: EEInfo: Flags: 0
    Lid: 11672   dwParam: 0x0 Msg: EEInfo: NumberOfParameters: 3
    Lid: 12952   dwParam: 0x0 Msg: EEInfo: prm[0]: Long val: 22964
    Lid: 15000   dwParam: 0x0 Msg: EEInfo: prm[1]: Pointer val: 0x0
    Lid: 15000   dwParam: 0x0 Msg: EEInfo: prm[2]: Pointer val: 0xFE01A8C000000000
    Lid: 62184
    Lid: 16280   dwParam: 0x0 Msg: EEInfo: ComputerName: n/a
    Lid: 8600    dwParam: 0x0 Msg: EEInfo: ProcessID: 6004
    Lid: 12696   dwParam: 0x0 Msg: EEInfo: Generation Time: 0414-08-21T09:10:43.8970000Z
    Lid: 10648   dwParam: 0x0 Msg: EEInfo: Generating component: 18
    Lid: 14744   dwParam: 0x0 Msg: EEInfo: Status: 10060
    Lid: 9624    dwParam: 0x0 Msg: EEInfo: Detection location: 318
    Lid: 13720   dwParam: 0x0 Msg: EEInfo: Flags: 0
    Lid: 11672   dwParam: 0x0 Msg: EEInfo: NumberOfParameters: 0
    Lid: 53361   StoreEc: 0x977
    Lid: 51859
    Lid: 33649   StoreEc: 0x977
    Lid: 43315
    Lid: 58225   StoreEc: 0x977
    Lid: 39912   StoreEc: 0x977
    Lid: 54129   StoreEc: 0x977
    Lid: 50519
    Lid: 59735   StoreEc: 0x977
    Lid: 59199
    Lid: 27356   StoreEc: 0x977
    Lid: 65279
    Lid: 52465   StoreEc: 0x977
    Lid: 60065
    Lid: 33777   StoreEc: 0x977
    Lid: 59805
    Lid: 52487   StoreEc: 0x977
    Lid: 19778
    Lid: 27970   StoreEc: 0x977
    Lid: 17730
    Lid: 25922   StoreEc: 0x977
    + CategoryInfo          : NotSpecified: (:) [New-MoveRequest], RemoteTransientException
    + FullyQualifiedErrorId : [Server=Exch01,RequestId=f6886977-92f1-4148-991b-aa76b449aff5,TimeStamp=8/21/2014 9:1
   0:43 AM] [FailureCategory=Cmdlet-RemoteTransientException] 7FCC37,Microsoft.Exchange.Management.RecipientTasks.New
MoveRequest
+ PSComputerName        : Exch01.domain.local
Please help as we are stuck here!!
Thanks in advance!!

Can yo ping server by name not by FQDN? e.g. ping server1.
Make sure firewall/antivirus not blocking communication. Disable antivirus and try
Thanks,
MAS
Please mark as helpful if you find my comment helpful or as an answer if it does answer your question. That will encourage me - and others - to take time out to help you.

Exchange 2013 SP1 CU8 installation stuck

Good Morning,
I'm just installing CU8 for Exchange 2013 on a DAG Member (only mailbox role installed), and setup is stuck at 49% of "Mailbox Role: Client Access service" for more than 2 hours now.
The ExchangeSetup logfile says:
[04/15/2015 06:44:20.0582] [2] Active Directory session settings for 'New-PerfCounters' are: View Entire Forest: 'True', Configuration Domain Controller: 'srv-dc02.oostvogels.com', Preferred Global Catalog: 'dc02.contoso.com', Preferred Domain Controllers: '{ dc02.contoso.com }'
[04/15/2015 06:44:20.0582] [2] User specified parameters: -DefinitionFileName:'ServiceProxyPoolCounters.xml'
[04/15/2015 06:44:20.0582] [2] Beginning processing new-PerfCounters
[04/15/2015 06:44:20.0582] [2] Processing file: C:\Program Files\Microsoft\Exchange Server\V15\Setup\Perf\ServiceProxyPoolCounters.xml
[04/15/2015 06:44:20.0582] [2] Performance counter name is Proxy Instance Count, type is NumberOfItems32.
[04/15/2015 06:44:20.0582] [2] Performance counter name is Current Outstanding Calls, type is NumberOfItems32.
[04/15/2015 06:44:20.0582] [2] Performance counter name is Total Number of Calls, type is NumberOfItems32.
[04/15/2015 06:44:20.0582] [2] Performance counter name is Calls/sec, type is RateOfCountsPerSecond32.
[04/15/2015 06:44:20.0582] [2] Performance counter name is Average Latency, type is AverageCount64.
[04/15/2015 06:44:20.0582] [2] Performance counter name is Base for Average Latency, type is AverageBase.
[04/15/2015 06:44:20.0582] [2] Performance counter category name is 'MSExchange ServiceProxyPool'.
[04/15/2015 06:44:20.0738] [2] Performance counter category name is 'MSExchange ServiceProxyPool'.
[04/15/2015 06:44:22.0255] [2] Ending processing new-PerfCounters
Does anyone have any suggestions or did you experience a similar issue?
I also can see some events like this:
Cmdlet failed. Cmdlet New-PerfCounters, parameters -DefinitionFileName "ADDriverCachePerformanceCounters.xml".
Thanks and best regards,
Sebastian

Hi,
According to your post, I understand that install Exchange 2013 SP1 CU8 in a DAG with MBX role failed with error “Cmdlet failed. Cmdlet New-PerfCounters, parameters -DefinitionFileName ‘ADDriverCachePerformanceCounters.xml’”.
If I misunderstand your concern, please do not hesitate to let me know.
I want to double confirm whether you deploy clean install or implement upgrade an existing Exchange Server 2013 installation to Cumulative Update 8.
To rebuild all Performance counters including extensible and third-party counters, type the following commands at an Administrative command prompt. Press ENTER after each command:
1. Rebuilding the counters:
    cd c:\windows\system32
    lodctr /R
2. Resyncing the counters with Windows Management Instrumentation (WMI):
    WINMGMT.EXE /RESYNCPERF
3. Stop and restart the Performance Logs and Alerts service.
4. Stop and restart the Windows Management Instrumentation service.
If the issue persists, please run to reload all the perf counters. For your reference:
http://blogs.technet.com/b/mikelag/archive/2010/09/10/how-to-unload-reload-performance-counters-on-exchange-2010.aspx
Thanks
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]
Allen Wang
TechNet Community Support

Exchange 2013 SP1 - Edge Tranport Role

Similar Messages

Maybe you are looking for