Exchange 2013 with TMG 2010 and Go Daddy

Hi all;
actually I'm new to exchange server 2013 and I need some help:
recently I installed exchange 2013 in our domain with contains TMG 2010
what I need is sending emails out.
currently I can send emails internaly
I have static IP and TMG and registered domain in Go daddy.
could someone help me by steps what to do?
in TMG?
in Exchange administration?
in Go Daddy?what records needed and how?
and should I do any configurations in my DNS?
please I'm stuck in this.
Thanks

Sorry, my fault. Try these links:
http://blogs.technet.com/b/exchange/archive/2012/11/21/publishing-exchange-server-2013-using-tmg.aspx
http://www.isaserver.org/articles-tutorials/configuration-general/publishing-exchange-2013-outlook-web-app-forefront-threat-management-gateway-tmg-2010.html
CRM Advisor

Similar Messages

OWA receives mail long before Outlook (Exchange 2013 with Outlook 2010 and 2013)

I recently upgraded my Exchange environment to Exchange 2013 SP1. The Outlook users are now experiencing a delay when receiving email. When they do arrive they appear in batches, often 20-45 minutes after they were sent, from a mailbox on the same server.
Additionally, the mail appears instantly when you monitor the inbox using OWA. The users are experiencing this on both Outlook 2010 and 2013 clients configured in both cached and non-cached modes. This appears to be a problem with Outlook connecting to Exchange.
Any suggestion about how to correct this would be greatly appreciated. Thanks!

Hi,
From your description, when users use OWA, they can receive emails normally. But if they use Outlook 2010 or Outlook 2013, there is a delay in receiving emails.
I recommend you use the Outlook safe mode to determine whether the problem is caused by add-ins. Also, please make sure users have installed the Outlook latest Service Pack.
If the issue persist, please create a new profile and check the result.
Hope it helps.
Best regards,
Amy Wang
TechNet Community Support

Migration Exchange 2010 to Exchange 2013 with CAS Array and DAG

Dear All,
I am starting the migration of Exchange 2010 2 servers (CAS/Mailbox) with DAG no CAS Array to Exchange 2013 with 2 servers CAS array and 2 Mailbox servers with DAG. I read on some blogs that no requirement of CAS array on Exchange 2013. My concern how to
configure NLB on CAS servers for the client to connect.
Please guide and have any deployment guide for this, kindly share.
Thanks

Hi ,
As you said there is no use and meaning of having the cas array in exchange 2013 and also thanks a lot to Microsoft for introducing an single namespace facility in exchange 2013.
My suggestion and Microsoft recommendation should be to go with hardware load balancers for exchange 2013 rather than using the windows NLB and round robin method.
Why we need to go for HLB ?
Disadvantages
of some load balancing methods :
Windows
NLB :-
If you use Windows NLB then it can provide redundancy on server level failure and not on application level.
DNS
round robin :-
In case if we use the windows round robin method for load balancing then it wouldn't provide server level
and application level redundancy during the failures.At the Same time we need to manually adjust the DNS records during the server failure but on the client end dns caches will create the issues.
Configuring NLB for exchange 2013 :
http://msexchangeguru.com/2013/08/14/windowsnlb/
NLB configurations for exchange 2010 and 2013 will be same.
Configuring round robin for exchange 2013 :
http://exchangeserverpro.com/exchange-2013-client-access-server-high-availability/
Advisable method is to have the CAS and MBX roles on the same box if NLB not comes it to play.Because windows failover clustering and NLB cannot be configured on the same box.In exchange 2013 cas role is a stateless server role so there is no need to have
that role on a separate box.
Thanks & Regards S.Nithyanandham

Exchange 2013 with Outlook 2010 anywhere - Public Folders disappear from Outlook favourites

Hi,
we have a 3 server Exchange 2013 SP1 DAG published with Forefront TMG.
Outlook 2010 anywhere connection works fine (only anywhere connection is possible, there are no clients in the exchange server AD).
The users are adding public folders to their local Outlook favorites. In about 10% of the Outlook starts, those public folders are missing in the favorites. Local favorites folders are still there, public folders are connected.
After restarting the Outlook a few times, the favorites are back.
Deleting the outlook.xml brought no success, the favorites seem to be saved somewhere on the exchange server.
Outlook 2010 is up to date, all hotfixes are installed.
There are no related entries in servers or clients eventlogs, the logs of the TMG server are normal.
Does anyone have a simular behavior?
Thanks in advance!

Hi,
According to your description,it is clear that something got corrupted, but it is hard to say directly what caused it. However, there are a few troubleshooting steps to determine what caused it and you can also make a backup of your Favorite Folders list
so you can easily restore it when it still happens.
Pleaser refer to the following article:
Favorite Folders empty upon restart
Note: Microsoft is providing this information as a convenience to you. The sites are not controlled by Microsoft. Microsoft cannot
make any representations regarding the quality, safety, or suitability of any software or information found there. Please make sure that you completely understand the risk before retrieving any suggestions from the above link.
Hope this helps!
Thanks.
If you have feedback for TechNet Subscriber Support, contact
[email protected]
Niko Cheng
TechNet Community Support

Exchange 2013 upgrade from 2010 and no mail flow and cannot move mailboxes

I am in the process of moving to Ex 2013 from 2010. I have installed Ex 2013 SP1 on a new server 2012 R2. All of my Ex 2010 servers are SP3 RU 5. Ex 2013 is running and I can connect through the EAC and see all other Exchange servers and connectors that
were already in existence. Several puzzling things are happening now that the servers are in coexistence:
1) As soon as Ex 2013 was installed on the network, many Outlook users are continuously being prompted to enter their domain credentials. They can cancel the prompt and Outlook still sends/receives email. No user mailboxes are on Ex 2013 yet.
Why is this happening?
2) I am following the Ex 2013 Deployment Assistant and I get to the step to move the Ex 2010 Arbitration mailbox to Ex 2013 and the move does not happen--it just says "syncing" and never completes. I tried moving a test mailbox from Ex 2010
to the 2013 database and I get the same result. I created the move request on the Ex2013 server and I see it as queued on the Ex2010 server, so I know they are "talking" to each other. However, when reviewing the status of the move I
see "MapiExceptionNoAccess: Unable to open message store".
3) There seems to be no mail flow on the same Ex2013 server or between the Ex 2010 and 2013 servers. I created two new test user mailboxes in Ex 2013. The Ex2013 mailboxes cannot send/receive to each other or to Ex 2010 users. This
seems strange, unless I am completely missing something in the Ex 2013 install?
I know this is a lot in one post, but following the Deployment assistant, I was hoping this would be something that others have faced. Thanks for any input here.

Does the below points already fit for you.
Exchange 2013 Supported with the following minimum versions of Exchange:
1) Exchange*** 2010 SP3 on all Exchange 2010 servers in the organization, including Edge Transport servers.
2) Exchange 2013 CU2 or later on all Exchange 2013 servers in the organization.
*** If you want to create an EdgeSync Subscription between an Exchange 2010 Hub Transport server and an Exchange 2013 SP1 Edge Transport
server, you need to install Exchange 2010 SP3 Update Rollup 5 or later on the Exchange 2010 Hub Transport server.
Thanks Prem P Rana MCSA Messaging 2003 MCSE 2003 Server MCTS MCITP Exchange 2007, 2010 Gurgaon, India http://blogs.msexchange-experts.com

Exchange 2013 with Outlook 2010 asking sometime for credentials

Hi Everyone,
I'm running Exchange Server 2013 on a Windows Server 2012.
Some of my user are sometime asked for credentials.
It happens both at outlook launch and when outlook is running.
And when we just cancel the credentials windows without password, outlook is connected to exchange again.
Everyone is running Office 2010 with SP1.
I have tried to put Outlook anywhere to NTLM and Negotiation authentication but it doesn't work either.
Any idea ?
Thanks in advance

I am getting this same problem. I checked all the steps in "Configure Mail Flow and Client Access" to no avail. When I click cancel in the credentials request popup, Outlook carries on and seems happy. Before long the credentials request returns
though.
We are running Exchange 2010 and have just added an Exchange 2013 Server. The errors I am getting are with new 2013 mailboxes and migrated mailboxes.
I ran "Test E-mail AutoConfiguration" and in the log, I see it first tries to contact our Exchange 2010 Server. After this fails, it then contact our Exchange 2013 Server.
SMTP=[email protected]
Attempting URL
https://smtp.domain.com/autodiscover/autodiscover.xml found through SCP
Autodiscover to
https://smtp.domain.com/autodiscover/autodiscover.xml starting
GetLastError=0; httpStatus=401
GetLastError=0; httpStatus=302
Autodiscover to
https://smtp.domain.com/autodiscover/autodiscover.xml Failed (0x800C8204)
Autodiscover URL redirection to
https://mail.domain.com:443/autodiscover/user..domain.com/autodiscover.xml starting
GetLastError=0; httpStatus=401
GetLastError=0; httpStatus=200
Autodiscover to
https://mail.domain.com:443/autodiscover/user..domain.com/autodiscover.xml Succeeded (0x00000000)
Any help will appreciated

Publish Exchange 2013 using UAG 2010 Sp4

Hi,
We need to publish Exchange 2013 through UAG 2010. But we are not getting any dedicated link for UAG 2010 to publish Exchange 2013. we have UAG 2010 with SP4.
Is there any Step by step UAG 2010 configuration link to publish Exchange 2013?
Thanks
jitender

Hi Jitender,
Based on my knowledge, publishing Exchange 2013 with UAG 2010 is similar with publishing Exchange 2010.
I find a related Blog and Guid for your reference:
1. Publishing Exchange Server 2010 with Forefront UAG and TMG
http://blogs.technet.com/b/exchange/archive/2010/07/16/publishing-exchange-server-2010-with-forefront-uag-and-tmg.aspx
2. Publishing Exchange Server 2010 with Forefront Unified Access Gateway 2010 and Forefront Threat Management Gateway 2010
http://www.microsoft.com/en-us/download/details.aspx?displaylang=en&id=8946
Please also notice the System requirement of both Exchange 2013 and UAG 2010.
System Requirement
Exchange 2013
http://technet.microsoft.com/en-us/library/aa996719(v=exchg.150).aspx
UAG 2010 SP4
Supported Operating System
Windows Server 2008 R2
Servers running Forefront UAG and SP4 require the following:
• Windows Server 2008 R2 Standard, Windows Server 2008 R2 Enterprise, or Windows Server 2008 R2 DataCenter.
• Microsoft Forefront Threat Management Gateway (TMG) 2010 Service Pack 2
Thanks
Mavis Huang
TechNet Community Support

Project Pro 2013 client Deployment with Lync 2010 and Team Explorer Excel Issues Following

Current machines are Office 2010 SP1 or SP2 32-bit
Just deployed Project 2013 Pro and Std to the existing machines that had Project 2010 Pro or Std. We selected the full install since people use integration into different tools.
Results:
lync 2010 64-bit when attending a meeting prompted user to start using and download the Lync Web Component, which breaks features such as muting, etc.
A repair sent to the workstations for Lync 2010 64-bit fixed that.
Team Explorer 2012 Export to excel from queries gives error Unable to cast COM object of type 'Microsoft.Office.Interop.Excel.ApplicationClass' to interface type 'Microsoft.Office.Interop.Excel._Application'. This operation failed because
the QueryInterface call on the COM component for the interface with IID '{000208D5-0000-0000-C000-000000000046}' failed due to the following error: The interface is unknown. (Exception from HRESULT: 0x800706B5).
Repair of Team Explorer, Office, Test Manager 2012, etc did not assist. if we go into excel and connect to TFS, we can then retrieve the query data. Just not from TFS exporting to excel. Had to unload Project 2013, repair Office 2010
and rebooted with project off the machine and now it works. It seems maybe the setup with the shared features and Office tools are breaking something? We need the ability for VBA and .net functionality, but what could be breaking this?

Hi,
Your environment will support 32 bit of Project professional 2013 (x86) as you have Windows and Office of (X86).
You try to modify registry then you wont face issue.
The issue when you hit a "1653" is that Windows
Installer "DisableRollback" is set. Office 2013 requires that "rollback" be enabled. If you are getting a "1653"
error in your logs as Ken did then the solution is to delete the "DisableRollback" (or set to '0') at the following registry keys:
HKEY_CURRENT_USER\Software\Policies\Microsoft\Windows\Installer
HKEY_LOCAL_MACHINE\Software\Policies\Microsoft\Windows\Installer
these are the issues I've seen:
Scheduler service was stopped. At a cmd window typing "net start schedule" resolves the problem.
CMD.exe was customized via the following registry key. Solution was to temporarily disable the customization by changing autorun value to autorun_old.
HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Command Processor
HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\Microsoft\Command Processor
Permission issues - seems some custom permissions affected Ingram's install which he explained in his previous post.
Environment variable "ComSpec" had been modified (semicolon added). Fix was to remove the added semicolon (there should be no semicolon).
The way to identify you are hitting this specific issue is if in the %temp%\OfficeSetup.log there is a mention of "Office64MUI.msi" failing to install with return value of 1603
If you want to enable verbose logging via the following key, rerun your failed install, and collect all the setup and MSI* logs that will give more information.
[HKEY_LOCAL_MACHINE\SOFTWARE\Policies\Microsoft\Windows\Installer]
"logging"= "voicewarmup"
kirtesh

Exchange 2013 with CAS and HLB in different sites

Hello...
Coming son, we'll deploy Exchange 2013 with high availability in all roles. The CAS and Hub Transport roles, are with a HLB; and the Mailbox with DAG. The infrastructure is formed by:
Citi1:
- AD Site 1
- 1 Hardware Load Balance: HLB01 to load balance the CAS and Hub Transport of Exc01 and Exc02
- 2 Exchange: Exc01 and Exc02 multiroles Exchange Server 2013
- 1 DAG for Citi1 databases: conformed by the Exc01 and Exc02
Citi2:
- AD Site 2
- 1 Hardware Load Balance: HLB02 to load balance the CAS and Hub Transport of Exc03 and Exc04
- 2 Exchange: Exc03 and Exc04 multiroles Exchange Server 2013
- 1 DAG for Citi2 databases: conformed by the Exc03 and Exc04
The Active Directory is one forest with one domain. The Domain Controllers are Windows Server 2012. The Site1 and Site 2 are connected by a WAN link. The accepted domain is domain.com. The smtp address is @domain.com
How to make that users of Citi1 always connect throught the HLB01 to their mailboxes; and the users of Citi2 always connect throught the HLB02 to their mailboxes if the autodiscover.domain.com is the same for all users?
I have not found documentation about
this architecture. Please help me.
Thank you very much.
Best regards, Javier Uribe

Hi javier,
In this issue, I guess you can try to use site affinity for the Autodiscover service for intranet-based traffic.
To use site affinity, you specify which Active Directory sites are preferred for clients to connect to a particular Autodiscover service
instance.
You configure site affinity by using the
Set-ClientAccessServer cmdlet. This cmdlet lets you specify the preferred Active Directory sites for connecting to the Autodiscover service on a specific Client Access server. After you configure site affinity for the Autodiscover service,
the client will connect to the Autodiscover service as you specified.
According to your needs, you might want to allow users in the site1 to use site1, users in site2 to use site2 to access the Autodiscover Service.
You can configure site scope for Client Access servers in the Site1 by following command.
Set-ClientAccessServer -Identity "site1-cas" -AutodiscoverServiceInternalURI "https://internal.domain.com/autodiscover/autodiscover.xml" –AutodiscoverServiceSiteScope “site1”
The Command for Site2.
Set-ClientAccessServer -Identity "site2-cas" -AutodiscoverServiceInternalURI "https://internal.domain.com/autodiscover/autodiscover.xml" –AutodiscoverServiceSiteScope “site2”
Hope it helps
Best regards

Exchange 2013 Issue: Outlook 2010 auto populating the From Tab when forwarding email

Exchange 2013 Issue: Outlook 2010 auto populating the From Tab when forwarding email
I am running Exchange 2013 and I have an end user who connects to it via Outlook 2010. All was going well till he went to forward an email and he noticed that the From button appeared and auto populated the sender's email address.
I have clicked the Empty Auto Complete List in Outlook's Send messages... still displayed the From tab when forwarding.
I recreated the profile in outlook... same thing.
I created the profile with outlook 2013... same thing.
There is only one user profile setup in Outlook.
(I know the from tab usually appears when you have multiple profiles setup in Outlook and/or when you configure the "From" tab.)
I opened the end user's email in Exch 2013's OWA... what was different here was when I clicked on the email and it opened, it did NOT have the Reply or Forward option... and it displayed as a "Draft" email.
Does anyone have any ideas?

So are you saying that the from button is filling the option with the original senders address (eg the person who sent the message to your user), or that it's filling in the your users address (in which case I don't understand what the issue is, since
it IS going from your user)?

Lync 2013 with outlook 2010 meeting error

I have installed lync basic 2013 with outlook 2010. The meeting add in is in place, but I get an error when trying to set up a Lync meeting "unable to identify the calendar owner"
What to do to correct this?

Hi,
You seem to get the error “Unable to identify the calendar owner. Please contact your support team.”
This is caused if the Online Meeting Add-in for Lync 2010 cannot determine the Simple Mail Transfer Protocol (SMTP) or Session Initiation Protocol (SIP) address of your Microsoft Outlook account. You need to contact your Exchange administrator.
If you mail server does not support online meeting(such as a pop3 server), you can join the meeting as anonymous user through the meeting URL.
You can also create a new profile to check the result:
http://support.microsoft.com/kb/829918/en-us
Regards,
Melon Chen
TechNet Community Support

Issues with Office 2010 and Acrobat Pro 8

Good Day All;
We are in the middle of upgrading from Windows XP to Windows 7 with Office 2010 and I was wondering if there are any issues with importing Office documents into Acrobat Pro 8. I have found out that there are a couple of issue with Office 201 and LifeCycle Designer.
Any comments would be helpful
Regards
Chomp

Acrobat 8 is not compatible with Microsoft Office 2010 and the PDFMaker plugins will not install. Only Acrobat X is compatible with Office 2010, and at this time only in 32-bit mode.
Acrobat 8 is also not officially compatible with Windows 7, again Acrobat X is the first version to carry approval for that OS. It will still install, but Adobe cannot guarantee it will operate perfectly in all cases, and doesn't provide install support for that combination.

Exchange 2013 RTM, CU1, CU2 and CU3 are no longer supported.

Exchange 2013 RTM, CU1 , CU2 and CU3 are no longer supported.
Before posting a question, please ensure you are at the latest CU.
http://blogs.technet.com/b/rmilne/archive/2015/04/14/end-of-exchange-2013-rtm-support.aspx
Twitter!:
Please Note: My Posts are provided “AS IS” without warranty of any kind, either expressed or implied.

Exchange 2013 RTM, CU1 , CU2 and CU3 are no longer supported.
Before posting a question, please ensure you are at the latest CU.
http://blogs.technet.com/b/rmilne/archive/2015/04/14/end-of-exchange-2013-rtm-support.aspx
Twitter!:
Please Note: My Posts are provided “AS IS” without warranty of any kind, either expressed or implied.

Unable to connect to Exchange 2013 using Outlook 2010/2013 with latest patch

Dear All,
I'm setting up Exchange 2013 CU2 coexist with Exchange 2010 SP3. Since we are still planning and testing, the internet is still pointing to 2010 for send/receive mails.
The 2013 environment are:-
2 X CAS server with MS NLB configured
2X MBX server with DA
Internal NLB/licent access: excas2013.int.my.domain
External access (current set on 2010 as well): webmail.my.domain
Certificate with valid subject name has been import to 2013 and 2010:
CN: webmail.mydomain
SAN: excas2013.int.my.domain
SAN: excas.int.my.domain (for 2010)
I am able to connect to my Exchange 2010 user thru 2013 CAS server and proxy to exhcnage 2010 by outlook. However, I cannot connect to Exchange 2013 user by outlook. During mail profile create of Exchange 2013 user by autodiscover (pointed to exchange 2013),
the process looks good:-
Establish network connection (checked)
Searching for [email protected] server settings (checked)
Log on to server
The process stop at "Log on to server" and a windows prompt, saying:
The action cannot be completed. The connection to Microsoft Exchange is unavailable. Outlook must be online or connected to complete this action.
Clicked OK, I can see:-
MS Exchange Server:
[email protected]
Mailbox:
=SMPT:[email protected]
WHen I click "Check Name", it said The name cannot be resolved.
I have no idea of what is going on. Just want some help~

I have checked the iis log:-
2013-09-23 06:58:29 10.144.144.71 POST /autodiscover/autodiscover.xml &cafeReqId=99ed5467-a294-481c-95eb-9b21d6530404; 443 mydomain\training101 10.144.85.4 Microsoft+Office/14.0+(Windows+NT+6.1;+Microsoft+Outlook+14.0.7106;+Pro) 200 0 0 8018
2013-09-23 06:58:29 10.144.144.71 RPC_IN_DATA /rpc/rpcproxy.dll [email protected]:6002&RequestId=f4652a19-2e8e-4652-a007-0cf0b7fb792e&cafeReqId=f4652a19-2e8e-4652-a007-0cf0b7fb792e; 443 - 10.144.85.4 MSRPC 401 1 2148074254
0
2013-09-23 06:58:29 10.144.144.71 RPC_OUT_DATA /rpc/rpcproxy.dll [email protected]:6002&RequestId=c48cda77-6008-423b-8e8b-d6d40f4d1b39&cafeReqId=c48cda77-6008-423b-8e8b-d6d40f4d1b39; 443 - 10.144.85.4 MSRPC 401 1 2148074254
0
2013-09-23 06:58:29 10.144.144.71 RPC_IN_DATA /rpc/rpcproxy.dll [email protected]:6002&RequestId=033f1ce4-43ba-49b1-b226-f4cc357e7702&cafeReqId=033f1ce4-43ba-49b1-b226-f4cc357e7702; 443 - 10.144.85.4 MSRPC 401 1 2148074252
15
2013-09-23 06:58:29 10.144.144.71 RPC_OUT_DATA /rpc/rpcproxy.dll [email protected]:6002&RequestId=d2424d25-ca9e-4867-922f-e527b041d9db&cafeReqId=d2424d25-ca9e-4867-922f-e527b041d9db; 443 - 10.144.85.4 MSRPC 401 1 64 0
2013-09-23 06:58:31 10.144.144.73 POST /autodiscover/autodiscover.xml &cafeReqId=ff35f49b-e418-4d55-b66c-dbae509cc12f; 443 - 10.144.92.17 Microsoft+Office/12.0+(Windows+NT+5.1;+Microsoft+Office+Outlook+12.0.6662;+Pro) 401 1 2148074254 0
2013-09-23 06:58:31 10.144.144.73 POST /autodiscover/autodiscover.xml &cafeReqId=033f8ed6-d7ce-41b2-8ed2-e275e22e53be; 443 mydomain\tkchung 10.144.92.17 Microsoft+Office/12.0+(Windows+NT+5.1;+Microsoft+Office+Outlook+12.0.6662;+Pro) 200 0 64 15
2013-09-23 06:58:37 10.144.144.71 POST /powershell serializationLevel=Full;ExchClientVer=15.0.712.24;clientApplication=ManagementShell;TargetServer=;PSVersion=3.0&sessionID=Version_15.0_(Build_711.24)=rJqNiZqNgbqnsr3Py9GWkYvRlZqc0ZyQkoHOxsvOxsbJzczNgcbQzczQzc/OzN/Ixc/KxczI376y&cafeReqId=5350aa81-6668-489e-b099-3b3647115f10;
80 mydomain\Administrator 10.144.144.71 Microsoft+WinRM+Client 500 0 0 180040
2013-09-23 06:58:46 10.144.144.71 RPC_IN_DATA /rpc/rpcproxy.dll [email protected]:6002&RequestId=f961c596-efff-4696-9188-611a0d151601&cafeReqId=f961c596-efff-4696-9188-611a0d151601; 443 - 10.144.85.4 MSRPC 401 1 2148074254
0
2013-09-23 06:58:46 10.144.144.71 RPC_OUT_DATA /rpc/rpcproxy.dll [email protected]:6002&RequestId=753d8852-ce19-459c-ac78-849c3e51e0a1&cafeReqId=753d8852-ce19-459c-ac78-849c3e51e0a1; 443 - 10.144.85.4 MSRPC 401 1 2148074254
15
2013-09-23 06:58:46 10.144.144.71 RPC_OUT_DATA /rpc/rpcproxy.dll [email protected]:6002&RequestId=c9e86049-c883-4b03-8546-143909361a80&cafeReqId=c9e86049-c883-4b03-8546-143909361a80; 443 mydomain\training101 10.144.85.4
MSRPC 404 0 64 78
2013-09-23 06:58:46 10.144.144.71 RPC_IN_DATA /rpc/rpcproxy.dll [email protected]:6002&RequestId=327ace4c-b2c8-44c1-95ba-7871727f60ef&cafeReqId=327ace4c-b2c8-44c1-95ba-7871727f60ef; 443 mydomain\training101 10.144.85.4
MSRPC 200 0 64 109
2013-09-23 06:58:46 10.144.144.71 RPC_IN_DATA /rpc/rpcproxy.dll [email protected]:6004&RequestId=a7c8daa9-e458-4f2d-b388-7300e8679dcd&cafeReqId=a7c8daa9-e458-4f2d-b388-7300e8679dcd; 443 - 10.144.85.4 MSRPC 401 1 2148074254
15
2013-09-23 06:58:46 10.144.144.71 RPC_OUT_DATA /rpc/rpcproxy.dll [email protected]:6004&RequestId=c40afede-dd8f-4ac7-a3dd-827872bb2e76&cafeReqId=c40afede-dd8f-4ac7-a3dd-827872bb2e76; 443 - 10.144.85.4 MSRPC 401 1 2148074254
15
2013-09-23 06:58:46 10.144.144.71 RPC_OUT_DATA /rpc/rpcproxy.dll [email protected]:6004&RequestId=2dc56148-1900-4044-b72a-4b13e5e871f0&cafeReqId=2dc56148-1900-4044-b72a-4b13e5e871f0; 443 mydomain\training101 10.144.85.4
MSRPC 404 0 64 15
2013-09-23 06:58:46 10.144.144.71 RPC_IN_DATA /rpc/rpcproxy.dll [email protected]:6004&RequestId=9475aad3-9537-4dac-86cb-6fdb187fa148&cafeReqId=9475aad3-9537-4dac-86cb-6fdb187fa148; 443 mydomain\training101 10.144.85.4
MSRPC 200 0 64 31
2013-09-23 06:58:46 10.144.144.71 RPC_IN_DATA /rpc/rpcproxy.dll [email protected]:6002&RequestId=11a54e96-d8d8-4649-8e01-f8138ebf7b8d&cafeReqId=11a54e96-d8d8-4649-8e01-f8138ebf7b8d; 443 - 10.144.85.4 MSRPC 401 1 2148074254
0
2013-09-23 06:58:46 10.144.144.71 RPC_OUT_DATA /rpc/rpcproxy.dll [email protected]:6002&RequestId=b1a3e503-1077-4144-84df-fcdb65a7eea4&cafeReqId=b1a3e503-1077-4144-84df-fcdb65a7eea4; 443 - 10.144.85.4 MSRPC 401 1 2148074254
15
2013-09-23 06:58:46 10.144.144.71 RPC_OUT_DATA /rpc/rpcproxy.dll [email protected]:6002&RequestId=5b5639ba-4c91-4351-bda6-bcec46d6b218&cafeReqId=5b5639ba-4c91-4351-bda6-bcec46d6b218; 443 mydomain\training101 10.144.85.4
MSRPC 404 0 0 15
2013-09-23 06:58:46 10.144.144.71 RPC_IN_DATA /rpc/rpcproxy.dll [email protected]:6002&RequestId=f200806f-3294-4210-8940-e3fee0385ccd&cafeReqId=f200806f-3294-4210-8940-e3fee0385ccd; 443 mydomain\training101 10.144.85.4
MSRPC 200 0 64 46
2013-09-23 06:58:46 10.144.144.71 RPC_IN_DATA /rpc/rpcproxy.dll [email protected]:6004&RequestId=675d6515-85da-43fa-9cd8-0a18ac06a71f&cafeReqId=675d6515-85da-43fa-9cd8-0a18ac06a71f; 443 - 10.144.85.4 MSRPC 401 1 2148074254
0
2013-09-23 06:58:46 10.144.144.71 RPC_OUT_DATA /rpc/rpcproxy.dll [email protected]:6004&RequestId=b97b2c3e-5309-4927-8330-fe0f339b5930&cafeReqId=b97b2c3e-5309-4927-8330-fe0f339b5930; 443 - 10.144.85.4 MSRPC 401 1 2148074254
0
2013-09-23 06:58:46 10.144.144.71 RPC_OUT_DATA /rpc/rpcproxy.dll [email protected]:6004&RequestId=504d462a-db21-4e4b-8568-79e4099d78c1&cafeReqId=504d462a-db21-4e4b-8568-79e4099d78c1; 443 mydomain\training101 10.144.85.4
MSRPC 404 0 0 31
2013-09-23 06:58:46 10.144.144.71 RPC_IN_DATA /rpc/rpcproxy.dll [email protected]:6004&RequestId=b4757b1e-8428-454a-91df-ca0a2153144f&cafeReqId=b4757b1e-8428-454a-91df-ca0a2153144f; 443 mydomain\training101 10.144.85.4
MSRPC 200 0 64 46

Setup first Exchange 2013 with mixed mode exchange 2007/2010

my company has exchange 2007 hub and edge and exchange 2010. I'm planning to retire all exchange 2007 first follow migrate to exchange 2013. so I have few questions as below ?
1. Do I need to unsubscribe hub 2007 from edge first before uninstall ? Currently we have 2 hubs (2007 and 2010). How can I remove hub 2007 from exchange edge server 2007 ?
2. let say once my landscape just have exchange 2010, is it installing our first exchange 2013 will impact our mail flow ? my understand there is NO impact until we switch over 'mail IP' to CAS 2013. am I correct ?
3. what is minimum requirement for co-exist with exchange 2013 for exchange 2010 ? is it enough with SP3 or I need to apply SP3 RU5 ? in deployment assistant, the requirement is SP3 RU5 but most article i read just mention SP3.
thx.

1. I would remove the edge subscription for sure. Then it isn't strictly necessary to uninstall Exchange Edge if you're just going to flatten the box anyway because that server isn't in Active Directory except through the Edge Subscription process.
I'm not sure what you're asking about "NO impact".
2. The coexistence requirements are clearly documented in TechNet. I'll leave it to you to search it since you can do that just as well as I can. That said, I would recommend that you go ahead and install the latest rollup on all your servers
first.
Ed Crowley MVP "There are seldom good technological solutions to behavioral problems."

Exchange 2013 with TMG 2010 and Go Daddy

Similar Messages

Maybe you are looking for