Exchange service disabled on new install

Hi
SBS 2011 installed on brand new Dell server using OpenMange method. The problem is that after installing all updates through Windows Update and few restarts when I wanted to configure Exchange all Exchange services were disabled. This is strange as I never
had this issue before in any of the previous SBS 2011 installs. What could be the problem and should I worry about it?
Thanks
Regards

Hi,
Regarding the current issue, I suspect that it may be caused by some updates have been installed via Windows Update. In order to resolve the issue, please try to install Exchange Server 2010
Service Pack 3 to see if it works. We could download it from the following link.
http://www.microsoft.com/en-us/download/details.aspx?id=36768
For details, please refer to the following article.
Solved : All Exchange 2010 services disabled after update
http://vworld.nl/?p=2085
Hope it helps.
Best Regards,
Andy Qi
TechNet Subscriber Support
If you are
TechNet Subscription user and have any feedback on our support quality, please send your feedback
here.
Andy Qi
TechNet Community Support

Similar Messages

Toshiba Service Station and new install

If I upgrade the ram, install my new 1tb SSD and install a new windows 8,1, would all I need to do is to install the service station to get all the drivers that are required for this laptop? It's a C series satallite.

Which computer? There is a label on the bottom.
-Jerry

Exchange 2013 CU2 will not install, Exchange is now in an unuseable state.

I have downloaded Exchange 2013 CU2 and attempted to install it from a local drive. Exchange 2013 is installed on a Server 2012 Standard VM in Hyper-V. I ran the two following commands before trying to install
setup.exe /PrepareSchema /IAcceptExchangeServerLicenseTerms
setup.exe /PrepareAD /IAcceptExchangeServerLicenseTerms
Upon trying to run the installer, I recieve the following error.
Error:
The following error was generated when "$error.Clear();
                    & $RoleBinPath\ServiceControl.ps1 EnableServices Critical
                " was run: "AuthorizationManager check failed.".
During my first install attept, the error was on step 4 of 15. I have tried to rerun the setup with no luck. I noticed the installer leaves all the Exchange services disabled, as well as winmgmt, remoteregistry, w3svc, iisadmin. These four services
are the critical services the errors refer to. I have verified my execution policy is correct
PS C:\Windows\system32> Get-ExecutionPolicy -list
Scope
ExecutionPolicy
MachinePolicy
Unrestricted
UserPolicy
Undefined
Process
Undefined
CurrentUser
Undefined
LocalMachine
RemoteSigned
Upon trying to rerun the setup, I have ran the following commands in order to start the critical services manually
Get-Service-name
winmgmt,
remoteregistry,
w3svc,
iisadmin
|
set-service -startuptype
automatic
Get-Service-name
winmgmt,
remoteregistry,
w3svc,
iisadmin
|
Start-Service
No matter what I do, the Exchange 2013 CU2 installer seems to fail. I'd appreciate any possible help with this.
Thanks,
Chris
To add to what I posted, I also have the following error in the event log.
[07/22/2013 13:57:01.0279] [1] Executing:
                    & $RoleBinPath\ServiceControl.ps1 EnableServices Critical
[07/22/2013 13:57:01.0373] [1] The following 1 error(s) occurred during task execution:
[07/22/2013 13:57:01.0373] [1] 0. ErrorRecord: AuthorizationManager check failed.
[07/22/2013
13:57:01.0373] [1] 0. ErrorRecord:
System.Management.Automation.PSSecurityException: AuthorizationManager
check failed. ---> System.Runtime.InteropServices.COMException: The
service cannot be started, either because it is disabled or because it
has no enabled devices associated with it. (Exception from HRESULT:
0x80070422)
   at System.Runtime.InteropServices.Marshal.ThrowExceptionForHRInternal(Int32 errorCode, IntPtr errorInfo)
   at System.Management.ManagementScope.InitializeGuts(Object o)
   at System.Management.ManagementScope.Initialize()
   at System.Management.ManagementObject.Initialize(Boolean getObject)
   at System.Management.ManagementObject.Get()
   at System.Management.Automation.PsUtils.GetParentProcess(Process current)
   at System.Management.Automation.SecuritySupport.GetExecutionPolicy(String shellId, ExecutionPolicyScope scope)
   at System.Management.Automation.SecuritySupport.GetExecutionPolicy(String shellId)
   at Microsoft.PowerShell.PSAuthorizationManager.CheckPolicy(ExternalScriptInfo script, PSHost host, Exception& reason)
at Microsoft.PowerShell.PSAuthorizationManager.ShouldRun(CommandInfo
commandInfo, CommandOrigin origin, PSHost host, Exception& reason)
at
System.Management.Automation.AuthorizationManager.ShouldRunInternal(CommandInfo
commandInfo, CommandOrigin origin, PSHost host)
   --- End of inner exception stack trace ---
at
System.Management.Automation.AuthorizationManager.ShouldRunInternal(CommandInfo
commandInfo, CommandOrigin origin, PSHost host)
   at
System.Management.Automation.CommandDiscovery.ShouldRun(ExecutionContext
context, PSHost host, CommandInfo commandInfo, CommandOrigin
commandOrigin)
   at
System.Management.Automation.CommandDiscovery.LookupCommandProcessor(CommandInfo
commandInfo, CommandOrigin commandOrigin, Nullable`1 useLocalScope,
SessionStateInternal sessionState)
   at
System.Management.Automation.CommandDiscovery.LookupCommandProcessor(String
commandName, CommandOrigin commandOrigin, Nullable`1 useLocalScope)
   at System.Management.Automation.ExecutionContext.CreateCommand(String command, Boolean dotSource)
at
System.Management.Automation.PipelineOps.AddCommand(PipelineProcessor
pipe, CommandParameterInternal[] commandElements, CommandBaseAst
commandBaseAst, CommandRedirection[] redirections, ExecutionContext
context)
   at
System.Management.Automation.PipelineOps.InvokePipeline(Object input,
Boolean ignoreInput, CommandParameterInternal[][] pipeElements,
CommandBaseAst[] pipeElementAsts, CommandRedirection[][]
commandRedirections, FunctionContext funcContext)
   at System.Management.Automation.Interpreter.ActionCallInstruction`6.Run(InterpretedFrame frame)
   at System.Management.Automation.Interpreter.EnterTryCatchFinallyInstruction.Run(InterpretedFrame frame)
[07/22/2013 13:57:01.0373] [1] [ERROR] The following error was generated when "$error.Clear();
                    & $RoleBinPath\ServiceControl.ps1 EnableServices Critical
                " was run: "AuthorizationManager check failed.".
[07/22/2013 13:57:01.0373] [1] [ERROR] AuthorizationManager check failed.
[07/22/2013
13:57:01.0373] [1] [ERROR] The service cannot be started, either
because it is disabled or because it has no enabled devices associated
with it. (Exception from HRESULT: 0x80070422)
[07/22/2013
13:57:01.0388] [1] [ERROR-REFERENCE]
Id=AllRolesMidFileCopyComponent___af0f15afe35c4e7cba121e546f405214
Component=EXCHANGE14:\Current\Release\Shared\Datacenter\Setup
[07/22/2013 13:57:01.0388] [1] Setup is stopping now because of one or more critical errors.
[07/22/2013 13:57:01.0388] [1] Finished executing component tasks.
[07/22/2013 13:57:01.0435] [1] Ending processing Start-MidFileCopy
[07/22/2013 13:58:09.0121] [0] End of Setup
[07/22/2013 13:58:09.0121] [0] **********************************************
I also have these two errors in event viewer that keep occuring.
Event 2280, IIS-W3SVC-WP
The Module DLL C:\Program Files\Microsoft\Exchange Server\V15\Bin\kerbauth.dll failed to load. The data is the error.
Event 2300, IIS-W3SVC-WP
The
worker process cannot access the CLR configuration file at 'C:\Program
Files\Microsoft\Exchange
Server\V15\bin\GenericAppPoolConfigWithGCServerEnabledFalse.config'.
Verify that the file exists and that the worker process has read access
to the file.

I kept quickly running the following two commands while the install was happening
Get-Service-name
winmgmt,
remoteregistry,
w3svc,
iisadmin
|
set-service -startuptype
automatic
Get-Service-name
winmgmt,
remoteregistry,
w3svc,
iisadmin
|
Start-Service
This caused the install to succeed.

Team Foundation Server 2013 update 4 New Install - Error 503 Service Unavailable for Sharepoint Central Admin

Hello,
I ran a new install of Team Foundation Server and let it install the built in SharePoint pieces on a single server setup. After the install i'm able to access the
http://teamfoundation:8080/tfs/ address without issue but am unable to create a project. When I attempt to create a project I get the following error:
TF30172: You do not have permission to create a new team project (when checking security i'm a member of the project collection administrators and Team Foundation Administrators)
This led me to look at the sharepoint central administration site where I receive the following error:
Error 503 Service Unavailable
I've gone through and validated the identity is set correctly in IIS for the following services:
SharePoint Central Admin v4
SharePoint15AppPool
The SharePoint Web Services Root is set as LocalService instead of the domain user.
The identity domain user is setup as local administrator on the Team Foundation Server. They are all set to use .net v4.0.30319 with integrated Pipeline mode.
Any help would be great!
Thanks!
Eric

Hi Eric,
Thanks for your post.
Please share your detailed team project creation log here.
In your TFS Admin Console>>Extensions for SharePoint Products tab, ensure SharePoint Web Application shows correctly in the right panel. And go to TFS Admin Console>>Application Tier>>SharePoint Web Applications tab, ensure your SharePoint
web application displays in the right panel, then select your SharePoint web application and click Repair Connection, ensure can repair successfully.
In your IIS Manager, select your SharePoint Central Administration V4 site and click Browser:17012(http) in the right panel, check if your SharePoint Central site can be opened successfully or not. If your SharePoint Central site cannot be accessed, I think
this issue relate to your SharePoint site, you should contact SharePoint experts to resolve this issue first. After you resolved this issue and your SharePoint Central Admin site can be accessed correctly, then try to create your team project(within SharePoint
site) again, if there still has issue when creating team project, please share the detailed error message here, we will try to resolve it.
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

I purchased lightroom and photoshop a week ago and installed it successfully on my new iMac. the open box iMac ended up being a lemon so i had to exchange it for a new one. best buy wiped the old computer clean. now id like to reinstall the lightroom a

I purchased lightroom and photoshop a week ago and installed it successfully on my new iMac. the open box iMac ended up being a lemon so i had to exchange it for a new one. best buy wiped the old computer clean. now id like to reinstall the lightroom and photoshop to my new computer but i don't know how. help!

Download and install the trial version from http://www.adobe.com/downloads.html and activate it with your serial number or Adobe ID.

ME22N Hide/Disable - Service : Attachment List - New - Create Attachment

Hi,
My requirement is to hide/disable the CREATE ATTACHMENT in ME22N.
Users were able to see Create attachment button through Service : Attachment List - > New -> Create Attachment, i need to hide/ disable this , so that they will not upload any attachment.
Please guide me .
regards,
Ashok kumar

Hi
There is a BADI 'GOS_SRV_SELECT' . You can use it for hinding create button.
This BADI is well documented..
Regards
Sachin

Security Update for exchange server 2013SP1 KB3011140 Stops all services and failes to install

Hi All,
Over the past 2 days this update has tried to run on the server in the evening but ends up failing. When it fails it is causing all of our exchange services to stop working and when we try to check e-mails the following day we find out the e-mail service
has been offline since the update.
Is there anything specific we need to do before running this update?
Cheers,

Hi,
As what Hotaka says, this update is available from
Windows Update. If it fails, we can also download and install the updates manually. The following stand-alone file is available for download from the Microsoft Download Center:
Download the security update for Exchange 2013 Service Pack 1 package now.
Download the security update for Exchange 2013 Cumulative Update 6 package now.
Regards,
Winnie Liang
TechNet Community Support

Disable "Found New Hardware" and Stop it automatically installing.

Hello All.
Ok the Issue I have is below and can't seem to find the correct answer I need.
I have two dell WYSE
boxes running Windows XP. I have one with an SSD to do all my configurations on and one is a 4GB flash box for steaming on to using WYSE WSM.
I have created a locked down version of XP with all sorts of registry hacks and Group policy to stop the end user accessing
system files and control panel etc..
I have it the way I want it but when I stream to the Flash Box, it picks up it has a 4GB SATA drive in it and installs it
and creates itself a drive letter E:\ and puts an icon in My Computer.This going
completely against what I wanted, I don't want the end user to have local drives. ONLY pendrives.
What I have done:
I have used group policy to restrict the view and access of A: B: C: & D: drives so it still allows me to use pen drives.
I have disabled some services to stop searing for new hardware on start up which hasnt worked.
There has been posts of going into device manager and disabling the hardware in there, but I cant do that on the FLASH box
as its already streaming and its locked down so cant the configs have to be made on the SSD box which doesn't have the 4GB flash drive in.
Any ideas?
I hope there is enough information on here for an answer.
Lets pull our brain power together and get an answer.
As per other posts and infinite Google searches, I know that many other people has a similar issue.

Did you check this ?
http://social.technet.microsoft.com/Forums/windows/en-US/deb4207b-4455-475e-91cd-876c181091bb/disable-found-new-hardware-wizard?forum=itproxpsp
Arnav Sharma | http://arnavsharma.net/ Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading
the thread.

SBS2003: disable Exchange Services

We use SBS2003 with Exchange - SMTP for send, POP3 for receive. We want to stop the server from sending & receiving mail while we export user mailboxes/PSTs for the purpose of importing them into Exch 2013. Is the best thing to do, in order to
accomplish this, to stop then disable the Exchange Services?
If so, please list the required Services that we stop and then disable.
Thank you!

Hi:
Is the Exchange 2013 live and on line now? If so, you can just unplug the 2003 sever from the internet and do the export at your leisure. That is the way I would do it unless you are doing some form of migration, in which case the migration will
move them.
Larry Struckmeyer[MVP] If your question is answered please mark the response as the answer so that others can benefit.

How can I disable notification for new install update for adobe??

How can I disable notification for new install update for adobe (adobe reader, flash player, etc.)
Is there way from SCCM2012 or group policy or any easy way?????
Please help me

If you mean the built-in functionality of Adobe Reader and Adobe Flash, it's different mechanism for both.
For the reader, check this guide for example:
http://www.adminarsenal.com/admin-arsenal-blog/bid/84409/Adobe-Customization-Wizard-XI-Tutorial
For flash, check this guide for example:
http://jthys.wordpress.com/2012/07/07/disable-automatic-updates-for-adobe-flash-shockwave-player-reader/
After you've studied the above guides, you need to implement those to be used with ConfigMgr application deployment so that when you deploy Reader/Flash, you get the result you want = no automatic update functionality.

Exchange 2007 New Install Error - Read only MultiValuedProperty does not support this operation

Existing Server/Exchange 2003 environment. New 2003 R2 x64 server fully patched and updated with no other apps installed attempting to install Exchange 2007 SP2.
Initially I was getting the error "Could not find the default Administrative Group ‘Exchange Administrative Group (FYDIBOHF23SPDLT)’". This I
fixed by completely uninstalling per this Microsoft article,
this Microsoft FixIt article and this recommended blog post, ending with
setup.com /preparead. I'm making progress, because now I'm getting a new error attempting the install. Specifically, Hub Transport installation fails with "Read only MultiValuedProperty does not support this operation."
Executing
setup.com /prepareSchema fails. I've set the msExchVer attribute for CN=Offline Address Lists to 4535486012416 and gotten no change, the install still fails. This
Googled page exactly describes my problem, and all anyone could say was to add this version number. It doesn't work. Pretty much none of the threads I've read have a resolution beyond this. I'm stumped, any help would be greatly appreciated.

What's the error message when executing setup.com /prepareSchema fails? failed at Organization Checks?
Could you please check whether you are on the right schema version?

New install of Crystal 2013 Server; getting errors

New install of Crystal 2013 Server on Windows 2012R2 Server
In the Connectivity Services; the ConnectionServer32 shows a state of Initalizing, and Disabled
In the Crystal Report Services; the CrystalReports2013ProcessingServer shows a state of Running with errors and Disabled
In the Crystal Report Services; the CrystalReports2013ReportApplicationServer shows a state of Stopped and Enabled
Hovering over Stopped I get "The Executable could not be launched. Possible reasons are insufficient RAM or disk space, or an invalid filepath or working directory. Actual reason: CreateProcess error + 14001, The application has failed to start because its side-by-side configuration is incorrect. Please see the application event log."
Application Event Log Entry:
Log Name:      Application
Source:        BusinessObjects_cms
Date:          4/21/2014 11:43:12 AM
Event ID:      33017
Task Category: General
Level:        Warning
Keywords:      Classic
User:          N/A
Computer:      DBH-TCRYSTAL01.sbcounty.gov
Description:
Unable to contact server DBHTCRYSTAL01.ConnectionServer32 on machine DBH-TCRYSTAL01.sbcounty.gov to perform status notification. Please check the server's system log for errors.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
    <Provider Name="BusinessObjects_cms" />
    <EventID Qualifiers="0">33017</EventID>
    <Level>3</Level>
    <Task>1</Task>
    <Keywords>0x80000000000000</Keywords>
    <TimeCreated SystemTime="2014-04-21T18:43:12.000000000Z" />
    <EventRecordID>32081</EventRecordID>
    <Channel>Application</Channel>
    <Computer>DBH-TCRYSTAL01.sbcounty.gov</Computer>
    <Security />
</System>
<EventData>
    <Data>DBHTCRYSTAL01.ConnectionServer32</Data>
    <Data>DBH-TCRYSTAL01.sbcounty.gov</Data>
</EventData>
</Event>
System Event Log Entry:
Log Name:      System
Source:        Microsoft-Windows-DistributedCOM
Date:          4/21/2014 7:49:07 AM
Event ID:      10016
Task Category: None
Level:        Error
Keywords:      Classic
User:          SYSTEM
Computer:      DBH-TCRYSTAL01.sbcounty.gov
Description:
The application-specific permission settings do not grant Local Launch permission for the COM Server application with CLSID
{05D1D5D8-18D1-4B83-85ED-A0F99D53C885}
and APPID
{AD65A69D-3831-40D7-9629-9B0B50A93843}
to the user NT AUTHORITY\SYSTEM SID (S-1-5-18) from address LocalHost (Using LRPC) running in the application container Unavailable SID (Unavailable). This security permission can be modified using the Component Services administrative tool.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
    <Provider Name="Microsoft-Windows-DistributedCOM" Guid="{1B562E86-B7AA-4131-BADC-B6F3A001407E}" EventSourceName="DCOM" />
    <EventID Qualifiers="0">10016</EventID>
    <Version>0</Version>
    <Level>2</Level>
    <Task>0</Task>
    <Opcode>0</Opcode>
    <Keywords>0x8080000000000000</Keywords>
    <TimeCreated SystemTime="2014-04-21T14:49:07.818690400Z" />
    <EventRecordID>8228</EventRecordID>
    <Correlation />
    <Execution ProcessID="668" ThreadID="804" />
    <Channel>System</Channel>
    <Computer>DBH-TCRYSTAL01.sbcounty.gov</Computer>
    <Security UserID="S-1-5-18" />
</System>
<EventData>
    <Data Name="param1">application-specific</Data>
    <Data Name="param2">Local</Data>
    <Data Name="param3">Launch</Data>
    <Data Name="param4">{05D1D5D8-18D1-4B83-85ED-A0F99D53C885}</Data>
    <Data Name="param5">{AD65A69D-3831-40D7-9629-9B0B50A93843}</Data>
    <Data Name="param6">NT AUTHORITY</Data>
    <Data Name="param7">SYSTEM</Data>
    <Data Name="param8">S-1-5-18</Data>
    <Data Name="param9">LocalHost (Using LRPC)</Data>
    <Data Name="param10">Unavailable</Data>
    <Data Name="param11">Unavailable</Data>
</EventData>
</Event>
I also have second Windows 2012R2 Server / Crystal 2013 Server install that is working just fine and the only difference is it is not a member of the Domain.
Barry Streets
[email protected]
510-238-2727 ext 2780

In addition to checklists provided by Josh; I would suggest you to perform a repository scan of the system to identify whether any objects were not installed properly and there might be a possible corruption. Use the link mentioned below to perform repository scanning.
How to use Repository Diagnostic Tool - Business Intelligence (BusinessObjects) - SCN Wiki
You can try to repair the install. Also as this is a new install you can directly go for re-installing the software.
PS: Try to re-download the software from the service market place rather than copying the installer from existing one.

SBS 2003 to 2011 Migration - Exchange Server 2010 cannot be installed

Hello,
We have a Small Business Server 2003 server that we are trying to migrate to SBS 2011 using the out of the box migration process. After the install, the SBS console showed a couple installation issues - the big one turned out to be "Exchange Server
2010 cannot be installed".
Here is the end of 'ExchangeSetup.log' showing various error messages:
[11/29/2014 23:00:07.0489] [2] Active Directory session settings for 'Get-ExchangeServer' are: View Entire Forest: 'True', Configuration Domain Controller: 'MB-MAINSERVER04.Contoso.local', Preferred Global Catalog: 'MB-MAINSERVER04.Contoso.local', Preferred Domain Controllers: '{ MB-MAINSERVER04.Contoso.local }'
[11/29/2014 23:00:07.0490] [2] Beginning processing get-exchangeserver -Identity:'MB-MAINSERVER04' -DomainController:'MB-MAINSERVER04.Contoso.local' -ErrorAction:'SilentlyContinue'
[11/29/2014 23:00:07.0506] [2] Searching objects "MB-MAINSERVER04" of type "Server" under the root "$null".
[11/29/2014 23:00:07.0518] [2] Previous operation run on domain controller 'MB-MAINSERVER04.Contoso.local'.
[11/29/2014 23:00:07.0518] [2] Previous operation run on domain controller 'MB-MAINSERVER04.Contoso.local'.
[11/29/2014 23:00:07.0518] [2] Preparing to output objects. The maximum size of the result set is "unlimited".
[11/29/2014 23:00:07.0522] [2] Unexpected Error
[11/29/2014 23:00:07.0522] [2] The operation couldn't be performed because object 'MB-MAINSERVER04' couldn't be found on 'MB-MAINSERVER04.Contoso.local'.
[11/29/2014 23:00:07.0523] [2] Ending processing get-exchangeserver
[11/29/2014 23:00:07.0523] [1] Executing:
if ($server -eq $null)
new-exchangeserver -DomainController $RoleDomainController -Name $RoleNetBIOSName
[11/29/2014 23:00:07.0545] [2] Active Directory session settings for 'New-ExchangeServer' are: View Entire Forest: 'True', Configuration Domain Controller: 'MB-MAINSERVER04.Contoso.local', Preferred Global Catalog: 'MB-MAINSERVER04.Contoso.local', Preferred Domain Controllers: '{ MB-MAINSERVER04.Contoso.local }'
[11/29/2014 23:00:07.0545] [2] Beginning processing new-exchangeserver -DomainController:'MB-MAINSERVER04.Contoso.local' -Name:'MB-MAINSERVER04'
[11/29/2014 23:00:07.0599] [2] [ERROR] Could not find the default Administrative Group 'Exchange Administrative Group (FYDIBOHF23SPDLT)'.
[11/29/2014 23:00:07.0600] [2] Ending processing new-exchangeserver
[11/29/2014 23:00:07.0607] [1] The following 1 error(s) occurred during task execution:
[11/29/2014 23:00:07.0607] [1] 0. ErrorRecord: Could not find the default Administrative Group 'Exchange Administrative Group (FYDIBOHF23SPDLT)'.
[11/29/2014 23:00:07.0607] [1] 0. ErrorRecord: Microsoft.Exchange.Data.Directory.SystemConfiguration.DefaultAdministrativeGroupNotFoundException: Could not find the default Administrative Group 'Exchange Administrative Group (FYDIBOHF23SPDLT)'.
at Microsoft.Exchange.Data.Directory.SystemConfiguration.ADSystemConfigurationSession.GetAdministrativeGroup()
at Microsoft.Exchange.Data.Directory.SystemConfiguration.ADSystemConfigurationSession.GetAdministrativeGroupId()
at Microsoft.Exchange.Management.SystemConfigurationTasks.NewExchangeServer.PrepareDataObject()
at Microsoft.Exchange.Configuration.Tasks.SetTaskBase`1.InternalValidate()
at Microsoft.Exchange.Configuration.Tasks.Task.ProcessRecord()
[11/29/2014 23:00:07.0609] [1] [ERROR] The following error was generated when "$error.Clear();
if ($server -eq $null)
new-exchangeserver -DomainController $RoleDomainController -Name $RoleNetBIOSName
" was run: "Could not find the default Administrative Group 'Exchange Administrative Group (FYDIBOHF23SPDLT)'.".
[11/29/2014 23:00:07.0609] [1] [ERROR] Could not find the default Administrative Group 'Exchange Administrative Group (FYDIBOHF23SPDLT)'.
[11/29/2014 23:00:07.0609] [1] [ERROR-REFERENCE] Id=ProvisionServerComponent___84489810458648f5ac6e47811394a284 Component=EXCHANGE14:\Current\Release\Shared\Datacenter\Setup
[11/29/2014 23:00:07.0610] [1] Setup is stopping now because of one or more critical errors.
[11/29/2014 23:00:07.0610] [1] Finished executing component tasks.
[11/29/2014 23:00:07.0618] [1] Ending processing Install-BridgeheadRole
[11/29/2014 23:00:07.0626] [0] The Exchange Server setup operation didn't complete. More details can be found in ExchangeSetup.log located in the <SystemDrive>:\ExchangeSetupLogs folder.
[11/29/2014 23:00:07.0633] [0] End of Setup
[11/29/2014 23:00:07.0633] [0] **********************************************
[11/29/2014 23:39:03.0429] [0] **********************************************
[11/29/2014 23:39:03.0435] [0] Starting Microsoft Exchange Server 2010 Setup
[11/29/2014 23:39:03.0435] [0] **********************************************
[11/29/2014 23:39:03.0456] [0] Local Time Zone: (UTC-08:00) Pacific Time (US & Canada).
[11/29/2014 23:39:03.0457] [0] Operating System version: Microsoft Windows NT 6.1.7600.0.
[11/29/2014 23:39:03.0469] [0] Setup version: 14.1.438.0.
[11/29/2014 23:39:03.0473] [0] Logged on user: Contoso2K3\Administrator.
[11/29/2014 23:39:06.0763] [0] Command Line Parameter Name='mode', Value='Install'.
[11/29/2014 23:39:06.0776] [0] ExSetupUI was started with the following command: '-mode:install'.
[11/29/2014 23:39:07.0413] [0] Setup is choosing the domain controller to use
[11/29/2014 23:39:07.0730] [0] Setup is choosing a local domain controller...
[11/29/2014 23:39:08.0459] [0] Setup has chosen the local domain controller MB-MAINSERVER04.Contoso.local for initial queries
[11/29/2014 23:39:08.0747] [0] PrepareAD has been run, and has replicated to this domain controller; so setup will use MB-MAINSERVER04.Contoso.local
[11/29/2014 23:39:08.0748] [0] Setup is choosing a global catalog...
[11/29/2014 23:39:08.0758] [0] Setup has chosen the global catalog server MB-MAINSERVER04.Contoso.local.
[11/29/2014 23:39:08.0819] [0] Setup will use the domain controller 'MB-MAINSERVER04.Contoso.local'.
[11/29/2014 23:39:08.0820] [0] Setup will use the global catalog 'MB-MAINSERVER04.Contoso.local'.
[11/29/2014 23:39:08.0823] [0] Exchange configuration container for the organization is 'CN=Microsoft Exchange,CN=Services,CN=Configuration,DC=Contoso,DC=local'.
[11/29/2014 23:39:08.0830] [0] Exchange organization container for the organization is 'CN=Contoso2K3,CN=Microsoft Exchange,CN=Services,CN=Configuration,DC=Contoso,DC=local'.
[11/29/2014 23:39:08.0867] [0] Setup will search for an Exchange Server object for the local machine with name 'MB-MAINSERVER04'.
[11/29/2014 23:39:08.0914] [0] No Exchange Server with identity 'MB-MAINSERVER04' was found.
[11/29/2014 23:39:09.0061] [0] The following roles have been unpacked: BridgeheadRole ClientAccessRole MailboxRole AdminToolsRole
[11/29/2014 23:39:09.0062] [0] The following datacenter roles are unpacked:
[11/29/2014 23:39:09.0064] [0] The following roles are installed: AdminToolsRole
[11/29/2014 23:39:09.0066] [0] The local server has some Exchange files installed.
[11/29/2014 23:39:09.0320] [0] Setup will use the path 'C:\Program Files\Windows Small Business Server\Bin\CMPNENTS\EXCHANGE14_SP1' for installing Exchange.
[11/29/2014 23:39:09.0332] [0] The installation mode is set to: 'Install'.
[11/29/2014 23:39:13.0558] [0] An Exchange organization with name 'Contoso2K3' was found in this forest.
[11/29/2014 23:39:13.0560] [0] Active Directory Initialization status : 'True'.
[11/29/2014 23:39:13.0561] [0] Schema Update Required Status : 'False'.
[11/29/2014 23:39:13.0562] [0] Organization Configuration Update Required Status : 'False'.
[11/29/2014 23:39:13.0563] [0] Domain Configuration Update Required Status : 'False'.
[11/29/2014 23:39:13.0564] [0] The locally installed version is 14.1.218.15.
[11/29/2014 23:39:13.0565] [0] Exchange Installation Directory : 'C:\Program Files\Microsoft\Exchange Server\V14'.
[11/29/2014 23:39:13.0920] [0] Applying default role selection state
[11/29/2014 23:39:13.0961] [0] Setup is determining what organization-level operations to perform.
[11/29/2014 23:39:13.0962] [0] Because the value was specified, setup is setting the argument OrganizationName to the value Contoso2K3.
[11/29/2014 23:39:13.0963] [0] Setup will run from path 'C:\Program Files\Microsoft\Exchange Server\V14\'.
[11/29/2014 23:39:13.0972] [0] InstallModeDataHandler has 0 DataHandlers
[11/29/2014 23:39:13.0972] [0] RootDataHandler has 1 DataHandlers
[11/29/2014 23:39:15.0491] [0] Setup encountered an exception when trying to access the setup state file: Could not find file 'C:\ExchangeSetupLogs\exchangeInstallState.xml'.
[11/29/2014 23:39:26.0117] [0] End of Setup
[11/29/2014 23:39:26.0117] [0] **********************************************
I should add that the source server's AD configuration might not be perfect due to this being the second attempt at a SBS 2011 migration install.
I'd be grateful for any help I can get on this as SBS migration has been plauged with multiple setbacks already. I really need to get this done! ;)
Thanks,
Voon

Thank you Larry and Al for your replies.
I used the 'official' migration
guide plus this page (http://www.techieshelp.com/step-by-step-guide-to-migrating-to-sbs-2011/)
as my migration references. The SBS migration prep tool gave no errors on the source server when I ran it.
I have a full system drive image plus a a system state backup from before migration. Though I am very loathed to rollback the migration and attempt a new one - again. I will do some searching to see if I can resolve the Exchange server problem and continue
the migration/installation. If not, then its a system state restore for me. One of Al's links had a resource for doing a thorough check of AD - which something I'd run if I have to another migration attempt.
I am also really tempted to open up a paid MS support ticket for them to help me fix this problem. :)

AC 5.3 - New Install or CopyBack

Hi Everyone
On my current project we have an existing AC 5.3 SP7 and we need to upgrade it to SP11 (not the latest SP 13 for various reasons which I won't go nto here).
So I have suggested that we create a new install of AC 5.3 SP7 copy the ruleset etc across via the import/export functionality of RAR and patch to SP11.
However, the Basis team want to use a "copyback" (which is apparently the standard way of creating/cloning a new system from an old one) followed by patching it to SP11.
Does anyone know of any issues about using the "copyback" to create a new AC 5.3 application? Should we do this? I have only ever been involved in build new installations of AC 5.3 and patching, so I do not know if teh "copyback" will work, as I am assuming that there will be issues with connectros etc.
Any help or guidance will be greatly appreciated.
regards
Simon

Man, you've really been getting your hands dirty recently
You can of course do a client copy, but there are a few things to consider:
- you will need to change the URLs to the ones for the test system in
- Visual Admin (IGSURL)
- All web service URLs
- make sure you don't accidentally point connectors to productive systems. Copy vs. export configuration means you won't be able to delete the connectors, you will need to disable them.
- in CUP make sure all your approvers are aware of the test system, or better yet, replace them with test approvers.
- CUP roles should be test system only
All in all, if it's a live system cleaning up the non-DEV things may be quite some work...
Frank.

New install help. Please and thanks!

I'm hoping somebody can tell me what's going wrong with my new install. Here are the details:
Win7 pro
i7 950
Quadro 4000 (with massive cooling blowing on the thing)
mxo2 mini max (because I'm slightly cheap, and yes, I feel a little like a hack plugging RCA cables rather than XLR for audio)
24g ram
Gtech 4tb graid
2 internal SATA drives (one boot, the other for utilities like tone, graphics I use often, etc.)
Software:
PremPro (AE, AME, etc) 5.51 (haven't updated to 5.52 - problem here?)
Squeeze 7
Trapcode plugins
Drivers:
NVidia: 276.14 (this is the Adobe approved one, at least so the download site said)
Matrox: mtxutils_551
So here are the issues:
--> Code 7 errors while editing a long program ("Open GL does not meet min specs for application"). Before this happens, generally premiere will become unresponsive, program screens will go black and then boom. On this program, I can get about 6 edits in before it blows.
--> Cannot export long program (2+ hours). (Matrox 1080i sequence - footage all P2 DVCPRO HD) Crashes after transcoding approximately 15-20 minutes of program. Exporting to Graid where project and footage is stored (is this an issue?) Premiere crashes and computer restarts. Tried many different export settings, from "match sequence settings" to Premiere's mpeg2 setting, to the Sorrensen and the Matrox ones.
(Adobe Tech support and a very nice guy named Vinay helped me with a small workaround which involved opening up a hidden admin login, and disabling some Microsoft services and exporting to my spare internal drive)
--> Also tried importing sequence directly into Encore and AME then transcoding through those. No luck there.
--> Premiere Pro on closing gives error message "Premiere Pro has stopped working; appcrash exception code 00005. Also, this is occasionally followed by a Visual C++ runtime error
--> Capture plugins from Matrox are unavailable. No Matrox capture settings are available.
--> No WYSUWYG control panel for MX02 (I know this is an Adobe site, but figured someone might have some insight maybe)
So there's the beginning. There are more, but these are the biggies at this point.
Thanks a million. I'm a very busy one man shop and sincerely appreciate any other busy people taking the time to give me some input on this.
Shaunn

Thanks Jim. Yeah, that was my suspicion as well. Right out of the box their damm plug-ins didn't install correctly, and it takes roughly a week to get familiar with all the "known issues" - a phrase that irritates me to no end - (if there are known issues - FIX EM before you sell me your s*%t! Can you imagine delivering a project to a client with a 14 page list of "known issues"?!?!? Seriously!)
There was a point where I really loved my Matrox products back in the old Digisuite days. But there was this point where their world class tech support policies changed, and frankly it seems that was the point where the whole company became hack. I was pretty skeptical about buying the mxo2 in the first place because of this, allowed myself to be "sold" because I needed to get back to work quickly, put the problem out of my mind and get back to work...and now I'm dealing with this.
Thanks for the link. I think you're right, it would be nice if Adobe would address monitoring through a gpu. But I'm guessing that won't be until CS6.5, by which point we'll all have to paying Adobe a monthly subscription vig to use their products. This crap irritates me to no end. I would love to see a reasonably priced and robust editing system that works like a hammer. I'm a busy 2 man shop - I gotta pound my video nails quickly and get on to the next house.
Assuming I get rid of matrox...what's the best current solution for monitoring? Doesn't sound like Aja or Blackmagic have any better solutions.
Shaunn

Exchange service disabled on new install

Similar Messages

Maybe you are looking for