Exclamation point and folder and nothing else
Hi... I have an older 20 g iPod. I dropped it (only 3 feet but hard surface) last week and after that it malfunctioned and then stopped functioning. I have tried the reset several times without success. My Mac does not recognize it either in the information about this Mac or the disk utility or the iPod updater. I would love to be able to revive it but had assuimed it dead. I can get an apple on the screen when I do a reset and the battery icon shows that it is charging ... and then the exclamation point with the folder comes up.
Any thoughts would be more than appreciated. Kay
Hello,
If a sad iPod icon or an exclamation point and folder icon appears on your iPod’s screen, or with sounds of clicking or HD whirring, it is usually the sign of a hard drive problem and you have the power to do something about it now. Your silver bullet of resolving your iPod issue – is to restore your iPod to factory settings.
http://docs.info.apple.com/article.html?artnum=60983
If you're having trouble, try these steps at different levels one at a time until the issue is resolved. These steps will often whip your iPod back into shape.
Make sure you do all the following “TRYs”
A. Try to wait 30 minutes while iPod is charging.
B. Try another FireWire or USB through Dock Connector cable.
C. Try another FireWire or USB port on your computer .
D. Try to disconnect all devices from your computer's FireWire and USB ports.
E. Try to download and install the latest version of iPod software and iTunes
http://www.apple.com/ipod/download/
http://www.apple.com/itunes/download/
F. Try these five steps (known as the five Rs) and it would conquer most iPod issues.
http://www.apple.com/support/ipod/five_rs/
G. Try to put the iPod into Disk Mode if it fails to appear on the desktop
http://docs.info.apple.com/article.html?artnum=93651
If none of these steps address the issue, you may need to go to Intermediate level listed below in logical order. Check from the top of the lists to see if that is what keeping iPod from appearing on your computer in order for doing the Restore.
Intermediate Level
A. Try to connect your iPod with another computer with the iPod updater pre-installed.
B. Still can’t see your iPod, put it in Disk Mode and connect with a computer, instead of doing a Restore on iPod Updater. Go and format the iPod instead.
For Mac computer
1. Open the disk utility, hope your iPod appears there (left hand side), highlight it
2. Go to Tab “Partition”, click either “Delete” or “Partition”, if fails, skip this step and go to 3
3. Go to Tab “Erase” , choose Volume Format as “MAC OS Extended (Journaled), and click Erase, again if fails, skip it and go to 4
4. Same as step 3, but open the “Security Options....” and choose “Zero Out Data” before click Erase. It will take 1 to 2 hours to complete.
5. Eject your iPod and do a Reset
6. Open the iPod Updater and click “Restore”
For Window computer
Go to folder “My Computer”
Hope you can see your iPod there and right click on the iPod
Choose “Format”. Ensure the settings are at “Default” and that “Quick Format” is not checked
Now select “Format”
Eject your iPod and do a Reset
Open the iPod Updater and click “Restore”
In case you do not manage to do a “Format” on a window computer, try to use some 3rd party disk utility software, e.g.“Partition Magic”.
C. Windows users having trouble with their iPods should locate a Mac user. In many cases when an iPod won't show up on a PC that it will show up on the Mac. Then it can be restored. When the PC user returns to his computer the iPod will be recognized by the PC, reformatted for the PC, and usable again. By the way, it works in reverse too. A Mac user often can get his iPod back by connecting it to a PC and restoring it.
Tips
a. It does not matter whether the format is completed or not, the key is to erase (or partly) the corrupted firmware files on the Hard Drive of the iPod. After that, when the iPod re-connected with a computer, it will be recognized as an fresh external hard drive, it will show up on the iPod updater.
b. It is not a difficult issue for a Mac user to find a window base computer, for a PC user, if they can’t find any Mac user, they can go to a nearest Apple Shop for a favor.
c. You may need to switch around the PC and Mac, try to do several attempts between “Format” and “Restore”
http://discussions.apple.com/thread.jspa?messageID=2364921�
Advance Level
A. Diagnostic mode solution
If you have tried trouble shooting your iPod to no avail after all the steps above, chances are your iPod has a hardware problem. The iPod's built-in Diagnostic Mode is a quick and easy way to determine if you have a "bad" iPod.
You need to restart your iPod before putting it into Diagnostic Mode. Check that your hold switch is off by sliding the switch away from the headphone jack. Toggle it on and off to be safe.
Press and hold the following combination of buttons simultaneously for approximately 10 seconds to reset the iPod.
iPod 1G to 3G: "Menu" and "Play/Pause"
iPod 4G+ (includes Photo, Nano, Video, and Mini): "Menu" and "Select"
The Apple logo will appear and you should feel the hard drive spinning up. Press and hold the following sequence of buttons:
iPod 1G to 3G: "REW", "FFW" and "Select"
iPod 4G+ (includes Photo, Nano, Video, and Mini): "Back" and "Select"
You will hear an audible chirp sound (3G models and higher) and the Apple logo should appear backwards. You are now in Diagnostic Mode. Navigate the list of tests using "REW" and "FFW". The scroll wheel will not function while in diagnostic mode. For further details on Diagnostic mode can be found at http://www.methodshop.com/mp3/ipodsupport/diagnosticmode/
Try to do the 5in1, HDD R/W and HDD scan tests. Some successful cases have been reported after the running the few tests under the Diagnostic mode. In case it does not work in your case, and the scan tests reports show some errors then it proves your iPod has a hardware problem and it needs a repairing service.
B. Format your iPod with a start disk
I have not tried this solution myself, I heard that there were few successful cases that the users managed to get their iPod (you must put your iPod in disk mode before connecting with a computer) mounted by the computer, which was booted by a system startup disk. For Mac, you can use the Disk Utility (on the Tiger OS system disk), for PC user, you can use the window OS system disk. Try to find a way to reformat your iPod, again it does not matter which format (FAT32, NTFS or HFS+) you choose, the key is to erase the corrupted system files on the iPod. Then eject your iPod and do a Reset to switch out from Disk Mode. Reboot your computer at the normal way, connect your iPod back with it, open the iPod updater, and hopefully your iPod will appear there for the Restore.
If none of these steps address the issue, your iPod may need to be repaired.
Consider setting up a mail-in repair for your iPod http://depot.info.apple.com/ipod/
Or visit your local Apple Retail Store http://www.apple.com/retail/
In case your iPod is no longer covered by the warranty and you want to find a second repairing company, you can try iPodResQ at your own risk
http://www.ipodresq.com/index.php
Just in case that you are at the following situation
Your iPod warranty is expired
You don’t want to pay any service charges
You are prepared to buy a new one
You can’t accept the re-sell value of your broken iPod
Rather than leave your iPod as paper-weight or throw it away.
You can try the following, but again, only do it as your last resort and at your own risk.
Warning ! – It may or may not manage to solve your problem, and with a risk that you may further damage your iPod, which end up as an expensive paper weight or you need to pay more higher repairing cost. Therefore, please re-consider again whether you want to try the next level
Last Resort Level
1. . Disconnecting the Hard Drive and battery inside the iPod – Warning !! Your iPod warranty will be waived once you open the iPod.
In Hong Kong there are some electronic shops offering an iPod service for Sad iPod, the first thing they do is to open up the iPod’s case and disconnecting the battery and the Hard Drive from the main board of the iPod. Wait for 5-10 minutes and reconnecting them back. The reason behind which I can think of is to do a fully reset of a processor of the iPod. In case you want do it itself and you believe that you are good on fixing the electronics devices and have experience to deal with small bits of electronic parts, then you can read the following of how to open the iPod case for battery replacement (with pictures)
http://www.kokopellimusic.us/KM_instructions.htm
Have I tried this myself? No, I am afraid to do it myself as I am squeamish about tinkering inside electronic devices, I have few experiences that either I broke the parts (which are normally tiny or fragile) or failed to put the parts back to the main case. Therefore, I agree with suggestion to have it fixed by a Pro.
2. Do a search on Google and some topics on this discussion forum about “Sad iPod”
What should I do with my iPod? Send it or keep it?
http://discussions.apple.com/thread.jspa?threadID=469080&tstart=0
Strange error on iPod (probably death)
http://discussions.apple.com/thread.jspa?threadID=435160&start=0&tstart=0
Sad Face on iPod for no apparent reason
http://discussions.apple.com/thread.jspa?threadID=336342&start=0&tstart=0
Meeting the Sad iPod icon
http://askpang.typepad.com/relevanthistory/2004/11/meeting_thesad.html#comment-10519524
Sad faced iPod, but my computer won’t recognize it?
http://discussions.apple.com/thread.jspa?messageID=2236095#2236095
iPod Photo: unhappy icon + warranty question
http://discussions.apple.com/thread.jspa?messageID=2233746#2233746
4th Gen iPod Users - are we all having the same problem?
http://discussions.apple.com/message.jspa?messageID=2235623#2235623
Low Battery, and clicking sounds
http://discussions.apple.com/thread.jspa?messageID=2237714#2237714
Sad faced iPod, but my computer won’t recognize it
http://discussions.apple.com/thread.jspa?messageID=2242018#2242018
Sad iPod solution
http://discussions.apple.com/thread.jspa?threadID=412033&tstart=0
I am not suggesting that you should follow as well, but just read them as your reference. You are the person to make the call.
Similar Messages
-
my ipod touch is showing a usb pointing to the itunes logo on the screen and nothing else. It won't switch on beyond that. Please help!
Sounds like your iPod is in restore mode. Connect it to iTunes. iTunes will pop a little message up saying that your iPod is in restore mode and asking you if you want to restore it, click yes. Your iPod will restore to factory settings and you will be given the chance to restore from a backup. You can do this or set it up as a new iPod.
Here is Apple's page on restoring your iPod.
http://support.apple.com/kb/ht1414
Hope that helps. -
Exclamation point and folder icon appears on iPod screen
I have a 20g Ipod and I am having lots of problems. Whenver I press a button it shows the apple logo followed by an exclamation point and folder icon. It ends with sounds of a clicking or HD whirring. Also, when I plug it into the computer, itunes prompts me with a message saying "Itunes has detected an Ipod in recovery mode. You must restore this Ipod before it can be used with Itunes". When I chose the option to restore it, it begins, but does not finish restoring it. It then gives me a message: "The Ipod "ipod" could not be restored. An unkown error occured (1418)". I also tried to restore by doing the following, but this failed as well:
Go to folder “My Computer”
Hope you can see your iPod there and right click on the iPod
Choose “Format”. Ensure the settings are at “Default” and that “Quick Format” is not checked
Now select “Format”
Eject your iPod and do a Reset
Open the iTunes 7 and click “Restore”
In case you do not manage to do a “Format” on a window computer, try to use some 3rd party disk utility software, e.g.“HP USB Disk Storage Format Tool”.
Any suggestions would be greatly appreciated
Thank You
Windows XPCheck these out:
iPod Folder with Exclamation Point After Disconnected From Computer
iPod Folder with Exclamation Point After Turned On
Good Thread About iPod Sad icon/Folder with Exclamation Point
I hope this helps! -
Ipod shows folder with exclamation point and computer won't recognize
My ipod resets itself each time that I try to turn it on, and then flashes the folder with the exclamation point. I have tried to restore it and update software but the computer won't recognize it. A few days before it broke the ipod would skip through some songs that it was unable to play for some reason, and now it makes a clicking sound when trying to start up. Did it die, or is there a way to fix this?
Hello,
If a sad iPod icon or an exclamation point and folder icon appears on your iPod’s screen, or with sounds of clicking or HD whirring, it is usually the sign of a hard drive problem and you have the power to do something about it now. Your silver bullet of resolving your iPod issue – is to restore your iPod to factory settings.
http://docs.info.apple.com/article.html?artnum=60983
If you're having trouble, try these steps at different levels one at a time until the issue is resolved. These steps will often whip your iPod back into shape.
Make sure you do all the following “TRYs”
A. Try to wait 30 minutes while iPod is charging.
B. Try another FireWire or USB through Dock Connector cable.
C. Try another FireWire or USB port on your computer .
D. Try to disconnect all devices from your computer's FireWire and USB ports.
E. Try to download and install the latest version of iPod software and iTunes
http://www.apple.com/ipod/download/
http://www.apple.com/itunes/download/
F. Try these five steps (known as the five Rs) and it would conquer most iPod issues.
http://www.apple.com/support/ipod/five_rs/
G. Try to put the iPod into Disk Mode if it fails to appear on the desktop
http://docs.info.apple.com/article.html?artnum=93651
If none of these steps address the issue, you may need to go to Intermediate level listed below in logical order. Check from the top of the lists to see if that is what keeping iPod from appearing on your computer in order for doing the Restore.
Intermediate Level
A. Try to connect your iPod with another computer with the iPod updater pre-installed.
B. Still can’t see your iPod, put it in Disk Mode and connect with a computer, instead of doing a Restore on iPod Updater. Go and format the iPod instead.
For Mac computer
1. Open the disk utility, hope your iPod appears there (left hand side), highlight it
2. Go to Tab “Partition”, click either “Delete” or “Partition”, if fails, skip this step and go to 3
3. Go to Tab “Erase” , choose Volume Format as “MAC OS Extended (Journaled), and click Erase, again if fails, skip it and go to 4
4. Same as step 3, but open the “Security Options....” and choose “Zero Out Data” before click Erase. It will take 1 to 2 hours to complete.
5. Eject your iPod and do a Reset
6. Open the iPod Updater and click “Restore”
For Window computer
Go to folder “My Computer”
Hope you can see your iPod there and right click on the iPod
Choose “Format”. Ensure the settings are at “Default” and that “Quick Format” is not checked
Now select “Format”
Eject your iPod and do a Reset
Open the iPod Updater and click “Restore”
In case you do not manage to do a “Format” on a window computer, try to use some 3rd party disk utility software, e.g.“Partition Magic”.
C. Windows users having trouble with their iPods should locate a Mac user. In many cases when an iPod won't show up on a PC that it will show up on the Mac. Then it can be restored. When the PC user returns to his computer the iPod will be recognized by the PC, reformatted for the PC, and usable again. By the way, it works in reverse too. A Mac user often can get his iPod back by connecting it to a PC and restoring it.
Tips
a. It does not matter whether the format is completed or not, the key is to erase (or partly) the corrupted firmware files on the Hard Drive of the iPod. After that, when the iPod re-connected with a computer, it will be recognized as an fresh external hard drive, it will show up on the iPod updater.
b. It is not a difficult issue for a Mac user to find a window base computer, for a PC user, if they can’t find any Mac user, they can go to a nearest Apple Shop for a favor.
c. You may need to switch around the PC and Mac, try to do several attempts between “Format” and “Restore”
Advance Level
A. Diagnostic mode solution
If you have tried trouble shooting your iPod to no avail after all the steps above, chances are your iPod has a hardware problem. The iPod's built-in Diagnostic Mode is a quick and easy way to determine if you have a "bad" iPod.
You need to restart your iPod before putting it into Diagnostic Mode. Check that your hold switch is off by sliding the switch away from the headphone jack. Toggle it on and off to be safe.
Press and hold the following combination of buttons simultaneously for approximately 10 seconds to reset the iPod.
iPod 1G to 3G: "Menu" and "Play/Pause"
iPod 4G+ (includes Photo, Nano, Video, and Mini): "Menu" and "Select"
The Apple logo will appear and you should feel the hard drive spinning up. Press and hold the following sequence of buttons:
iPod 1G to 3G: "REW", "FFW" and "Select"
iPod 4G+ (includes Photo, Nano, Video, and Mini): "Back" and "Select"
You will hear an audible chirp sound (3G models and higher) and the Apple logo should appear backwards. You are now in Diagnostic Mode. Navigate the list of tests using "REW" and "FFW". The scroll wheel will not function while in diagnostic mode. For further details on Diagnostic mode can be found at http://www.methodshop.com/mp3/ipodsupport/diagnosticmode/
Try to do the 5in1, HDD R/W and HDD scan tests. Some successful cases have been reported after the running the few tests under the Diagnostic mode. In case it does not work in your case, and the scan tests reports show some errors then it proves your iPod has a hardware problem and it needs a repairing service.
B. Format your iPod with a start disk
I have not tried this solution myself, I heard that there were few successful cases that the users managed to get their iPod (you must put your iPod in disk mode before connecting with a computer) mounted by the computer, which was booted by a system startup disk. For Mac, you can use the Disk Utility (on the Tiger OS system disk), for PC user, you can use the window OS system disk. Try to find a way to reformat your iPod, again it does not matter which format (FAT32, NTFS or HFS+) you choose, the key is to erase the corrupted system files on the iPod. Then eject your iPod and do a Reset to switch out from Disk Mode. Reboot your computer at the normal way, connect your iPod back with it, open the iPod updater, and hopefully your iPod will appear there for the Restore.
If none of these steps address the issue, your iPod may need to be repaired.
Consider setting up a mail-in repair for your iPod http://depot.info.apple.com/ipod/
Or visit your local Apple Retail Store http://www.apple.com/retail/
In case your iPod is no longer covered by the warranty and you want to find a second repairing company, you can try iPodResQ at your own risk
http://www.ipodresq.com/index.php
Just in case that you are at the following situation
Your iPod warranty is expired
You don’t want to pay any service charges
You are prepared to buy a new one
You can’t accept the re-sell value of your broken iPod
Rather than leave your iPod as paper-weight or throw it away.
You can try the following, but again, only do it as your last resort and at your own risk.
Warning ! – It may or may not manage to solve your problem, and with a risk that you may further damage your iPod, which end up as an expensive paper weight or you need to pay more higher repairing cost. Therefore, please re-consider again whether you want to try the next level
Last Resort Level
1. . Disconnecting the Hard Drive and battery inside the iPod – Warning !! Your iPod warranty will be waived once you open the iPod.
In Hong Kong there are some electronic shops offering an iPod service for Sad iPod, the first thing they do is to open up the iPod’s case and disconnecting the battery and the Hard Drive from the main board of the iPod. Wait for 5-10 minutes and reconnecting them back. The reason behind which I can think of is to do a fully reset of a processor of the iPod. In case you want do it itself and you believe that you are good on fixing the electronics devices and have experience to deal with small bits of electronic parts, then you can read the following of how to open the iPod case for battery replacement (with pictures)
http://www.kokopellimusic.us/KM_instructions.htm
Have I tried this myself? No, I am afraid to do it myself as I am squeamish about tinkering inside electronic devices, I have few experiences that either I broke the parts (which are normally tiny or fragile) or failed to put the parts back to the main case. Therefore, I agree with suggestion to have it fixed by a Pro.
2. Do a search on Google and some topics on this discussion forum about “Sad iPod”
Strange error on iPod (probably death)
http://discussions.apple.com/thread.jspa?threadID=435160&start=0&tstart=0
Sad Face on iPod for no apparent reason
http://discussions.apple.com/thread.jspa?threadID=336342&start=0&tstart=0
Meeting the Sad iPod icon
http://askpang.typepad.com/relevanthistory/2004/11/meeting_thesad.html#comment-10519524
Sad faced iPod, but my computer won’t recognize it?
http://discussions.apple.com/thread.jspa?messageID=2236095#2236095
iPod Photo: unhappy icon + warranty question
http://discussions.apple.com/thread.jspa?messageID=2233746#2233746
4th Gen iPod Users - are we all having the same problem?
http://discussions.apple.com/message.jspa?messageID=2235623#2235623
Low Battery, and clicking sounds
http://discussions.apple.com/thread.jspa?messageID=2237714#2237714
Sad faced iPod, but my computer won’t recognize it
http://discussions.apple.com/thread.jspa?messageID=2242018#2242018
I am not suggesting that you should follow as well, but just read them as your reference. You are the person to make the call. -
When I go in to SYSTEM PREFERENCE and click on DESKTOP/SCREENSAVERS it says pictures loading but then I get that coloured circle and nothing else - I then have to force quit
Hi Mende 1
I have just tried what you suggested and it came up with - folder can't be found? -
Why is my hard drive full when I'm only running the operating system and nothing else is loaded? No music, pics, nothing! I understand the hard drive is small at 60 gig, but I can't believe the os would take up that much space.
First, empty the Trash if you haven't already done so. Then reboot. That will temporarily free up some space. According to Apple documentation, you need at least 9 GB free on the startup volume for normal operation. You also need enough space left over to allow for growth of your data. Use a tool such as OmniDiskSweeper to explore your volume and find out what's taking up the space. Proceed further only if the problem hasn't been solved. ODS can't see the whole filesystem when you run it just by double-clicking; it only sees files that you have permission to read. To really see everything, you have to run it as root. Back up all data now. Launch the Terminal application in any of the following ways: ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.) ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens. ☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid. After installing ODS in the Applications folder, drag or copy — do not type — the following line into the Terminal window, then press return:sudo /Applications/OmniDiskSweeper.app/Contents/MacOS/OmniDiskSweeper
You'll be prompted for your login password, which won't be displayed when you type it. You may get a one-time warning not to screw up.
I don't recommend that you make a habit of this. Don't delete anything while running ODS as root. When you're done with it, quit it and also quit Terminal. -
An exclamation point and the battery icon??????????
when i connected my ipod to computer.....it was showed the an exclamation point and the battery icon and i can't connect it either charge........if u know why........please help me...............
See if anything on this page helps: "iPod shows a folder icon with exclamation point when you turn it on" http://docs.info.apple.com/article.html?artnum=61003
-
IPod Adapter icon appears and nothing else happens HELP
i got this ipod and all of a sudden a picture (icon) appears on the screen its a picture of a ipod Usb port adapter and nothing else happens its stuck there if anyone knows what to do please help.
ThanxIf you have more than one user account, these instructions must be carried out as an administrator.
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
Step 1
Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left.
Enter "BOOT_TIME" (without the quotes) in the search box. Note the timestamps of those log messages, which refer to the times when the system was booted. Now clear the search box and scroll back in the log to the last boot time when you had the problem. Post the messages logged before the boot, while the system was unresponsive or was failing to shut down. Please include the BOOT_TIME message at the end of the log extract.
Post the log text, please, not a screenshot. If there are runs of repeated messages, post only one example of each. Don’t post many repetitions of the same message. When posting a log extract, be selective. In most cases, a few dozen lines are more than enough.
Please do not indiscriminately dump thousands of lines from the log into a message.
Important: Some private information, such as your name, may appear in the log. Edit it out by search-and-replace in a text editor before posting.
Step 2
Still in Console, look under System Diagnostic Reports for crash or panic logs, and post the entire contents of the most recent one, if any. In the interest of privacy, I suggest you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header of the report, if present (it may not be.) Please don’t post shutdownStall, spin, or hang logs — they're very long and not helpful. -
my autofill stopped working recently. I looked under preferences and all the necessary boxes are checked. When I start to fill out a form, the autofill box comes up, but when I click on it, it turns blue and nothing else happens.
Back up all data, then test after each of the following steps that you haven't already tried. Stop when the problem is resolved.
1. Press the down-arrow key. (Credit to ASC member iNeight.)
2. Quit and relaunch Safari. Force quit if necessary.
3. Click in the first field to be filled, and then select
Edit ▹ AutoFill Form
from the menu bar. You may have to reload the page in order to do this.
4. Select
Contacts ▹ Preferences ▹ vCard
and uncheck the box marked
Enable private me card
if it's checked.
5. Select your card in Contacts. Then select
Card ▹ Make This My Card
from the menu bar.
6. In Safari, select
Safari ▹ Preferences ▹ AutoFill ▹ AutoFill web forms: Using info from my Contacts card
If the box was already checked, uncheck it and then check it again.
7. Launch the Keychain Access application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Keychain Access in the icon grid.
Select the login keychain from the list on the left side of the Keychain Access window. If your default keychain has a different name, select that.
If the lock icon in the top left corner of the window shows that the keychain is locked, click to unlock it. You'll be prompted for the keychain password, which is the same as your login password, unless you've changed it.
Right-click or control-click the login entry in the list. From the menu that pops up, select Change Settings for Keychain "login". In the sheet that opens, uncheck both boxes, if not already unchecked.
From the menu bar, select
Keychain Access ▹ Preferences ▹ First Aid
If the box marked Keep login keychain unlocked is not checked, check it.
Select
Keychain Access ▹ Keychain First Aid
from the menu bar and repair the keychain. Quit Keychain Access.
8. Run Software Update and install any available updates. -
Why does iphoto screen go grey and a spinning wheel in the middle of the page and nothing else
can someone tell me why i always get a spinning wheel in the middle of the page and nothing else when trying to open iphoto
Either the program, the iPhoto Library or the iPhoto preference file is hosed.
First thing is first, backup your user file folders to a external hard drive and disconnect.
The easiest (and most likey the cause of your issue) to fix would be the iPhoto preference file
iPhoto preference file fix
Look in your /Users/Library/Preference for a file like
com.apple.iphotopreferences.plist
or
com.apple.iphoto.plist
and delete it and reboot, restart iPhoto and re-enter your preferences.
If your on OS X Lion, your going to have to use the Finder's "Go To" to get to the Library as it's hidden as in Snow Leopard it's not.
Reinstall iPhoto
If that doesn't resolve your issue and your on Lion, you can redownload the iLife software from the MacAppStore and simply reinstall it, which will overwrite iPhoto and fix it.
If your on Snow Leopard you reboot holding c from the 10.6 grey installer disks (only) that came with your comptuer and simply reinstall OS X 10.6 which will reinstall iPhoto (the 10.6.3 Snow Leopard retail disk doesn't have iLife)
If you purchased iLife from the boxed set, then reinstall it.
If you had iLife from 10.5 and your on 10.6 or 10.7, or got it free with 10.6 and now on 10.7, then your going to have to wait until you try the next step (then extract iPhoto from the installer disk using Pacifist or purchase iLife)
Rebuild iPhoto Library
If that doesn't resovle your issue you can right click (or control click) on the iPhoto Library and "Show Package Contents" inside will be a folder with all your original photo's. Copy these out and move the iPhoto Library out of the Pictures folder and rename it (if you can) so iPhoto can't find it.
Then restart iPhoto and see if it creates a new iPhoto Library, then simply import the pictures from the copy you made.
If it fails to work after this, there is a corrupted picture in your iPhoto, you'll have to repeat the same process with importing a few pictures at a time until you can locate the corrupted ones. -
I have just tried to connect my Mac book pro to an LG Plasma TV via an iWires Mini DisplayPort to HDMI cable. All I get on my TV is the Mac wallpaper and nothing else. I am missing something really silly, could anyone help please.
Hi there. I also bought an iWires mini Display port to HDMI cable and have an LG LED/LCD TV. I plugged it in to my MB Pro and followed the very small writing that came in the package and got both audio and video going. You need to change the audio settings from within System Preferences on your Mac to select your TV as the audio output.
My concern is the data latency - do you experience a delay between moving your mouse on the MBPro and the TV displaying the movement? It is only a fraction of a second, but certainly enough to be annoying, especially in a cable as expensive as the iWire. -
About once a month I receive the Software update notice that has failed. How do I find out who/what is trying to update? If I decided I want this update how do I allow it to continue? If I decided I do not want this update how do I stop it and its attempt to update? The only response allowed is "OK". When OK is selected the window goes away and nothing else happens.
Hi sharkbiscuit79,
Yes your cabinet 10 on the Crediton exchange has already been installed and linked with a FTTC DSLAM cabinet (making it able to provide FTTC fibre broadband) and has been Accepting FTTC orders since December 2013. PCP10 (with it's DSLAM cabinet within 100meters of it) is locate on the junction of Commercial Road and the A3072.
However by the looks of things your are just too far away to obtain a FTTC (VDSL2) connection, meaning FTTC fibre broadband is not available to you.
Have a look at the Connecting Devon and Somerset Considerations (particularly the last paragraph) - http://www.connectingdevonandsomerset.co.uk/where-when-map-conditions/
Your best bet is to talk to Connecting Devon and Somerset to see if there are any further plans to get a fibre based service to your area via https://www.connectingdevonandsomerset.co.uk/contact-us/ (as your area may not be inscope of any further deployment). Best give them your full address and landline number too as they can check if you are within a NGA area.
jac_95 | BT.com Help Site | BT Service Status
Someone Solved Your Question?
Please let other members know by clicking on ’Mark as Accepted Solution’
Try a Search
See if someone in the community had the same problem and how they got it resolved. -
Everytime i go on Itunes it tells me i have to restore my ipod but everytime i do, it just tells me to do it again? When i try and use my ipod it just has a connect to itunes sign and nothing else, it wont work at all?
I updated itunes and everything but nothings working and i just can't figure it out?
Everytime i restore the stupid thing, it never pops up in my itunes again like its supposed to!Loop
Maybe:
Restore loop (being prompted to restore again after a restore successfully completes)
Troubleshoot your USB connection. If the issue persists, out-of-date or incorrectly configured third-party security software may be causing this issue. Please follow Troubleshooting security software issues. .
Next try placing in DFU mode and then restoring.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
Then try restoring on another computer.
Last, make an appointment at the Genius Bar of an Apple store.
Apple Retail Store - Genius Bar -
Hi, I can't seem to get my ipod 32gb 4th gen to sync with itunes. It's brand new, but everytime I plug it in it says can't access Itunes store and nothing else happens. I enabled my firewall to allow itunes but it still can't access the store. Please help.
If you look at the feed, and look at the entry 'The end to an exciting field season in Aulavik National Park' you will see the line:
<pubDateFri, 29 Jul 2011 04:00:00 GMT</pubDate>
You have not closed the 'pubdate' tag - there should be a '>' as the 9th character. Because the tag has been left open, it invalidates everything which follows it, and thus the entire feed. iTunes therefore cannot read it, which is why the Store has not updated. Add the '>' and republish, and all should be well.
It's always worth checking your feed by subscribing manually, from the 'Advanced' menu, or by clicking the 'subscribe free' button on the Store page (both do the same thing) - if you can subscribe to the feed it should be OK. -
Blue screen of death? I just updated my MacBook Air with the latest OX (25 Jun 11). When I restart - I get the Apple logo and then a blue screen and nothing else. Help!!!
Insert the install disk and press c on startup. Select your langauge then, if there's a menubar click utilities then click Disk Utility. If you didn't see the menubar continue with the installer until you see it.
Once in disk utitly select the drive and repair permissions.
After the repair is done, quit the utiltiy.
You can try to reboot and see if it works if you reboot, but if it doesn't repeat the same as before again.
Now you can continue with the installer and install the os.
Quit
Maybe you are looking for
-
Process: Zombies Ate My Friends [989] Path: /Applications/Zombies Ate My Friends.app/Contents/MacOS/Zombies Ate My Friends Identifier: com.glu.macos.zamf1 Version: 1.0.1 (1.0.1) App Item ID: 642547094 App External
-
I have an iPhone 4S and it just locked me out from anything else BUT twitter??
I was using Twitter and went to click my home button...all of a sudden the screen went black. And when I clicked the home button again, it didn't take me to my lock screen, but back to Twitter. I did this multiple times and the same thing kept happen
-
Youtube - Does not work in all Browsers
Greetings, I have an issue were Youtube is not functional in any of my web browsers (Safari, Firefox, and Chrome). I cannot find a fix to this issue anywhere else. All I keep getting is "An error occured, please try again later". I have I have tried
-
Can you help me with my iphone problem? I can not open my safari in my iphone
-
Report alignment and header not proper while modifying using MS Office 2007
We have an RTF template designed using old MS Office version (1997 - 2003). Wehn we save the document after making any change using MS Office 2007, the alignment is changed in the merged PDF output (esp. table cell border hiding / displaying). Moreov