Executing Csim start on a MGCP gateway

Folks,
Can i use Csim start command on a Mgcp Gateway to ring one of the phones?? i have put in a VOIP dialpeer pointing the dial pattern to the callmanager, but it does not work?
any ideas?
Thanks

Would this harm me in anyway since i have MGCP defined ever where (over 10 gateways running MGCP).
If i just create a H.323 gateway and do not assin it to a route-group or route-pattern, would it be the safest approach?
We want to test the PRI's . Since out route plan has redundancy built into it, we can test the pri's using ip phones, i was hoping that i could do a CSIM start and Test Pri at the gateway level. Any better way to doing it?
also as long at the PRI port on the router is under MGCP control, will it let me use H.323 commands and route call to the PSTN??
Thanks,

Similar Messages

MGCP Gateway Change port from POTS to Loop Start

I have an existing MGCP gateway port that I need to change from POTS to Loop start, however I have not seen a setting in UCM that allows me to do this. When I try to delete the port, it ask if I want to delete this gateway and I'm scared that it will blow all my ports away. Does anyone know how to reset this port to the default so I can program loop start or updat the existing port?

Yeah you need to delete the port from the gateway and re-add it to change it. You will need to remove route pattern/route group dependencies in order to delete the port. I recommend you use the Dependency Records to find out what RGs this port is assigned to so that you can add it back in.
If these are FXS ports, I'd actually recommend you keep it at POTS until CM 8.5, though, since LS is the default configuration for the port in IOS, and there is this bug on CM, which isn't fixed until 8.5:
CSCtf22348
MGCP FXS GroundStart and LoopStart need Prefix DN; remove Attendant DN

Remote C2901 MGCP gateway won't register with CUCM

Hi, all,
We have a central call manager, we are setting up a remote office with a C2901 voice gateway that has a T1 PRI, this gateway is being configured as a H.323 gateway, everything worked fine. Now I want to get SRST working such that when WAN goes down, employees can still make outbound calls and take inbound calls. I followed SRST documentations when configuring CUCM and C2901, I would say the documentations are clear and easy to follow -- only thing is there is no adequate explanation of why those commands need to be there and I can not get SRST to work.
1), First, a basic concept question, why do we need to configure "ccm-manager fallback-mgcp"? or any MGCP related configuration on C2901? how does MGCP play the role in SRST? the router is configured as a simple voice gateway, when WAN is intact, we use H.323 protocol, when WAN goes down, we still don't need MGCP ...
2), Assuming that we needed all those SRST related MGCP configuration, I would expect C2901 to register to call manager, but I could not get this device to register as a MGCP gateway, debug mgcp packets shows:
*Sep 5 16:52:47.571: MGCP Packet sent to 10.128.181.5:2427--->
RSIP 201356931 *@voicegw-remoteoffice.local.domain MGCP 0.1
RM: restart
<---
*Sep 5 16:52:47.631: MGCP Packet received from 10.128.181.5:2427--->
500 201356931
<---
I verified the domain name is exactly the same as the name configured on CUCM, I tried multiple time toggling ip domain name on C2901 also, somehow CUCM does not like RSIP message from C2901, I don't have knowledge to get debug information from CUCM side of why CUCM does not like the MGCP message sent by C2901
3), When the communication is blocked from C2901 to central call manager (by using a simple ACL on C2901's default gateway device), I can still make the inbound call to an IP phone, which means, phones were correctly registered to C2901 when communication to call manager is broken, but I can not make outbound call, phones always get quick busy beeps, test call from C2901 itself (by using "csim start") is fine, which means dial-plan and ISDN/PRI is fine.
I believe we are just doing very very basic configuration and this is a common scenario, what could I do wrong?

You dont need the mgcp related commands if you are using H323. The commands that you need are:
application
global
service alternate default
call-manager-fallback (or) telephony-service and the relevant commands under it.
Also make sure that SRST reference has been added to the DP and the phones reset after the change made. This is what tell the phone to register to the SRST gateway when the WAN is down. The IP specified in the SRST reference should match whats configured under call-manager-fallback.

CUCM 9.1.1 - MGCP gateway won't register to my 2811

Hello
I am trying to add a MGCP gateway on a 2811.
I have configured as per the book, but it is not registering,
here is my Router config:
2811 uptime is 2 hours, 4 minutes
System returned to ROM by power-on
System image file is "flash:c2800nm-adventerprisek9-mz.124-11.XJ4.bin"
Cisco 2811 (revision 53.50) with 509952K/14336K bytes of memory.
Processor board ID FHK1302F0YV
3 FastEthernet interfaces
24 Serial interfaces
1 Channelized T1/PRI port
1 Virtual Private Network (VPN) Module
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
125440K bytes of ATA CompactFlash (Read/Write)
Configuration register is 0x2102
2811#sh run
Building configuration...
Current configuration : 7125 bytes
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname 2811
boot-start-marker
boot-end-marker
card type t1 0 2
enable secret 5 $1$ax07$1yOFpGS1rHGYm873l9n9q/
no aaa new-model
clock timezone PCLAIRE -5
clock summer-time PCLAIRE recurring
network-clock-participate wic 2
network-clock-select 1 T1 0/2/0
ip cef
no ip dhcp use vrf connected
ip domain name homelab.local
multilink bundle-name authenticated
isdn switch-type primary-ni
voice-card 0
dspfarm
dsp services dspfarm
controller T1 0/2/0
framing esf
linecode b8zs
pri-group timeslots 1-24
description Home_PBX
vlan internal allocation policy ascending
interface FastEthernet0/0/0
description To Home Network$ETH-LAN$
ip address 192.168.15.50 255.255.255.0
duplex auto
speed auto
interface Serial0/2/0:23
description Home_PBX
no ip address
encapsulation ppp
isdn switch-type primary-ni
isdn incoming-voice voice
control-plane
voice-port 0/2/0:23
description Home_PBX
ccm-manager mgcp
ccm-manager config server 192.168.15.11 - THIS IS THE SUBSCRIBER , SHOULD IT BE THE PUBLISHER ?
ccm-manager config
mgcp
gateway
timer receive-rtp 1200
Here is what I get:
2811(config)#do sh ccm-manager
MGCP Domain Name: 2811.homelab.local
Priority        Status                   Host
============================================================
Primary         None
First Backup    None
Second Backup   None
Current active Call Manager:    None
Backhaul/Redundant link port:   2428
Failover Interval:              30 seconds
Keepalive Interval:             15 seconds
Last keepalive sent:            09:55:04 PCLAIRE Jan 16 2014 (elapsed time: 02:00:24)
Last MGCP traffic time:         11:34:19 PCLAIRE Jan 16 2014 (elapsed time: 00:21:08)
Last failover time:             None
Last switchback time:           None
Switchback mode:                Graceful
MGCP Fallback mode:             Not Selected
Last MGCP Fallback start time: None
Last MGCP Fallback end time:    None
MGCP Download Tones:            Disabled
Backhaul/Redundant link is down
Configuration Auto-Download Information
=======================================
No configurations downloaded
Current state: Downloading XML file
Configuration Download statistics:
        Download Attempted             : 1
          Download Successful          : 1
          Download Failed              : 0
        Configuration Attempted        : 0
          Configuration Successful     : 0
          Configuration Failed(Parsing): 0
          Configuration Failed(config) : 0
Last config download command:
FAX mode: cisco
Configuration Error History:
2811(config)#
Any help greatly appreciated
John Bachman

Still same problem, I have erased all that related to mgcp on my router, to start from scratch
2811(config)#controller T1 0/2/0
2811(config-controller)#pri-group timeslots 1-24 service mgcp
Cannot overwrite no serv type with one. Unconfigure existing configuration and reconfigure
2811(config-controller)#
Where is this error coming from ??
Here is what I want to try:
192.168.15.10 - pub
192.168.15.11 - sub
controller T1 0/2/0
pri-group timeslots 1-24 service mgcp
interface Serial0/0/0:23
isdn bind-l3 ccm-manager
ccm-manager config server 192.168.15.10 192.168.15.11
ccm-manager config
ccm-manager redundant-host 192.168.15.11
ccm-manager mgcp
mgcp
mgcp call-agent 192.168.15.10 service-type mgcp version 0.1

CUCM 9 & AS5850, Using MGCP Gateways not found in "Gateway Type" list...

I have an application where I need to control a large, AS5850 gateway using MGCP. CUCM version is 9.1, soon to be 10.0. The gateway is populated with CT3 cards.
We have confirmed that the AS5850 does in fact support MGCP, however it is not listed as an option in the list of gateway product choices when adding a new gateway in CUCM. So my first question:
1) How do you add an MGCP gateway in CUCM when it is not listed in the "gateway type" drop-down list? It seems there must be a way to do this. Other well known gateways such as the AS5300, AS5400 etc.. are also notably absent from the list of gateway choices. Perhaps there is a template that can be edited?
If anyone has experience utilizing an AS5850 gateway with CUCM & MGCP, it would be very useful to see sample configuration programming from your gateway.
Many thanks

Hi,
As per the datasheet, the Cisco AS5850 Universal Gateway supports H.323, SIP, and MGCP call-control protocols with extensive SNMP management and debugging capabilities. It works with the Cisco PGW 2200 Softswitch, the Cisco BTS 10200 Softswitch, and many partner softswitches as well.
http://www.cisco.com/en/US/prod/collateral/iad/ps509/ps512/product_data_sheet09186a008007cc48.html
It looks like that its not supported with CUCM.
HTH
Manish

Set B Channel ID information to Preferred in MGCP Gateway

Hi All,
We recently had some E1 PRI issues and our Service Provider has asked us to set B Channel ID information to Preferred.
We are using a MGCP Gateway with CUCM 9.1.2
When we enable ISDN debug we could see the Channel ID as Exclusive.
Jul 25 13:02:07.566: ISDN Se0/0/0:15 Q931: TX -> SETUP pd = 8 callref = 0x0043
        Sending Complete
        Bearer Capability i = 0x8090A3
                Standard = CCITT
                Transfer Capability = Speech
                Transfer Mode = Circuit
                Transfer Rate = 64 kbit/s
        Channel ID i = 0xA98381
                Exclusive, Channel 1
I tried to change it to Preferred by configuring the command, "isdn negotiate-bchan" under the serial interface but still debug shows it as Exclusive only.
Let me know whether we can change the B Channel information either in CUCM or MGCP Gateway.

Hi
Can you try the below:-
1- interface x/x/x:15
isdn protocol-emulate network
isdn bchan-number-order ascending
then test again
2-Go to CUCM - gateway and do the below
CHANNEL IE TYPE " TIMESLOTS "
Thanks
please rate all useful information

MGCP Gateways and Cisco Fax

We are considering adding a fax solution to our IPT infrastructure using Cisco Fax (Captaris RightFax). Ideally we would like the same voice gateways to terminate the fax calls (internal voice calls use QSIG and external calls use Q.931). Can this be achieved with MGCP-controlled Voice gateways? Can T.38 fax be configured with an MGCP gateway. I have seen examples where H.323 dial-peers are required to talk SIP to the Fax Server.
If not, is an alternative to use a back-to-back PRI connection between a voice gateway port and the Fax Server ISDN card, with appropriate route patterns in CallManager to route the fax calls to Fax Server, using Cisco Fax Relay?

with cm 4.2.3 there is mgcp t.38 support implemented.
see release notes cm 4.2.3
http://www.cisco.com/application/pdf/en/us/guest/products/ps6729/c1178/ccmigration_09186a0080724724.pdf
regards
mehmet

Cannot register MGCP gateway to CCM 4.1

Hello,
   I am running an application which simulates a MGCP gateway vs. a real CCM 4.1. I am not able to register the endpoints as you can see from the snapshot attached. I guess the problems lies in the 200 response to the following AUEP:
AUEP 89 AALN/S0/SU0/[email protected] MGCP 0.1
F: X+SRTP/A
200 89 OK
X: 2
L: p:20, a:PCMU, b:64, e:ON, s:ON
    I have also attached the trace file and CCM logs.
   I have 2 questions on this matter:
what is the correct format of the 200 message which needs to be sent to AUEP with SRTP?
how can I configure CCM not to sent this AUEP with SRTP(I have a similar one in my setup which is not sending this AUEP)?
Thanks in advanced for you support,
Ionut

Restrictions for Cisco Multiservice IP-to-IP Gateway Configuration:
Restrictions for SIP-to-SIP Call Signaling:
Transcoding is not supported.
SIP-to-H.323 Call-Signaling Features:
Codec transcoding (G.711-G.729) - supported
other:Transcoding is not supported on the Cisco 7200 and the Cisco 7301
copied from:cisco Multiservice IP-to-IP Gateway
http://www.cisco.com/en/US/products/sw/voicesw/ps5640/products_configuration_guide_book09186a0080409b6d.html
I have not found a solution, but i'd be interested in what you find though.

Problema para sacar llamadas -csim start [Número]-

Al momento de ejecutar el comando csim start 90453221323934
GTW#csim start 90453221323934
csim: called number = 90453221323934, loop count = 1 ping count = 0
csim err csimDisconnected recvd DISC cid(2753)
csim: loop = 1, failed = 1
csim: call attempted = 1, setup failed = 1, tone failed = 0
Pero NO sale la llamada...es decir...mi celular (0453221323934) no recibe esta llamada....
Saludos.

GTW#sh running-config
Building configuration...
Current configuration : 7653 bytes
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname GTW
boot-start-marker
boot-end-marker
logging buffered 51200 warnings
no aaa new-model
network-clock-participate wic 3
network-clock-select 4 E1 0/3/0
dot11 syslog
ip cef
ip domain name pruebas.com.mx
multilink bundle-name authenticated
voice-card 0
dspfarm
dsp services dspfarm
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
h323
modem passthrough nse codec g711ulaw
sip
voice class codec 1
codec preference 1 g711alaw
codec preference 2 g729r8
codec preference 3 g729br8
codec preference 4 g711ulaw
crypto pki trustpoint TP-self-signed-2390140610
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-2390140610
revocation-check none
rsakeypair TP-self-signed-2390140610
archive
log config
hidekeys
controller E1 0/3/0
framing NO-CRC4
ds0-group 0 timeslots 1-15,17-31 type r2-digital r2-compelled ani
cas-custom 0
country telmex
category 2
answer-signal group-b 1
caller-digits 4
groupa-callerid-end
description TELMEX2
controller E1 0/3/1
framing NO-CRC4
description Llamadas Axtel
ip forward-protocol nd
ip forward-protocol udp syslog
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
control-plane
voice-port 0/3/0:0
cptone MX
timeouts interdigit 5
sccp ccm group 1
associate profile 10 register Conferences
associate profile 11 register Transcode
dspfarm profile 11 transcode
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec g729br8
maximum sessions 9
associate application SCCP
shutdown
dspfarm profile 10 conference
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec g729br8
associate application SCCP
shutdown
dial-peer voice 20 pots
description CELULARES PRUEBA
destination-pattern 90453221323934
incoming called-number .
direct-inward-dial
port 0/3/0:0
forward-digits 13
line con 0
password
login
line aux 0
line vty 0 4
password
login
transport input all
scheduler allocate 20000 1000
end
Ahi te mando el sh run....por otro lado..cuando habilito el debug voice ccapi inout .....y corro de nuevo el comando csim start [numero], el debug no me muestra nada
GTW #debug voice ccapi inout
voip ccapi inout debugging is on
GTW#csim start 90453221323934
GTW#
GTW#

SRST with T1 CAS MGCP Gateway

Hello - we are trying to configure SRST on our T1 CAS MGCP gateway. We have been informed by a Cisco engineer that we cannot use SRST on a T1 CAS MGCP gateway and that the gateway must first be reconfigured as an H.323 gateway in order to implement SRST. Router is version 12.2(15)T14 and CCM 4.1 Any comments would be truly appreciated...thank you.

SRST doesn't support MGCP but does support MGCP to H.323 failback. You can still configure your router/CCM with MGCP then use the fallback commands for MGCP.
Looking at the SRST 4.0 system guide, page 42, T1 CAS is supported. With your version of IOS you would be running SRST 2.1, this is also supported.
http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122newft/122t/122t15/srst21/srstv21.pdf
http://www.cisco.com/univercd/cc/td/doc/product/voice/srst/srst40/srst40ad/s40sa.pdf
The ccm-manager fallback-mgcp command was added in IOS 12.2(11)T so it should be in your version. This is what you would need to do MGCP fallback to your H323 along with the call application alternate default.
http://www.cisco.com/univercd/cc/td/doc/product/software/ios123/123tcr/123tvr/vrht_c4.htm#wp1061367
http://www.cisco.com/univercd/cc/td/doc/product/software/ios123/123tcr/123tvr/vrht_c1.htm#wp1670149
I would say it might be possible as I don't see anything saying no. Though remember MGCP fallback to H323 over SRST doesn't have call preservation.
Lastly here is a document on the SRST MGCP/H323 fallback.
http://www.cisco.com/en/US/tech/tk1077/technologies_configuration_example09186a008012ecc6.shtml
Please rate any helpful posts
Thanks
Fred

FAX Detection Application for a MGCP Gateway

Hi,
I have an MGCP Gateway and a Right Fax Solution along with CUCM. Was wondering if FAX detection application can be configured for this setup or is FAX detection only for H323 gateways.
Thanks
Prakash

It uses TCL script, so it is not available with MGCP.
Chris

MGCP Gateway Help

I have a site where they treat the employees, from a finance perspective, as 2 companies. Because of this they was all their calls to go out different BRIs/PRIs so they can just charge each 'company' their share. Last time I visited there I met with a reseller and one of their voice engineers said I could do this by creating 2 different MGCP gateways for the single router. There may have been something I missed in translation (Japanese) but I cannot figure out how to make a second MGCP gateway for this router.
Any ideas?

Create different set of CSS, partitions, route patterns. Assign the new CSS to the other users with access to partitions that new duplicate route patterns are assigned to and point to the dedicated ports on the gateway.
Chris
Sent from Cisco Technical Support iPhone App

Trouble adding second port BRI in a 2801 MGCP gateway

my config is CCM 413 with a 2801 SRST including a VIC2-2BRI .
I have configured the 2801 as MGCP gateway on the CCM, added the module VIC2-2BRI and configured the BRI 0/0/0 in this gateway.
this BRI work properly with the PSTN . I can make successfull call inbound and outbound
Now I want to add the second BRI (ie BRI 0/0/1 ) in the gateway for the same hunt group, the same PSTN provider.
When I do that this BRI can't register and make different kind of problem on the existing well working BRI.
for example I noticed that I can make inbound or outbound call with connected state but no voice in the two way.
I noticed also that the first BRI become completely blocked after two call.
I have verified the conf of the BRI 0/0/1 but i don't see any difference with the BRI 0/0/0 .
the only way to get back good working of the BRI 0/0/0 is to remove BRI 0/0/1 from the gateway conf.

Hello,
That is a good news though. Can you please share to me the TAC case nr? So I can refer this to tAC. Because we have also opened a CASE for the same problem on the 3725 but not hear from TAC yet for the patch!
I got another image ie. IPVOICE version 12.4.1.9 from a friend that has the patch for this problem on the 2801 but there is no SPSERVICES image yet.
Now it looks that Cisco has a newer image.
Thanks in advance.
Regards

MGCP Gateway With ISDN BRI interface

Hi Guys,
I have a voice gateway with a BRI card on slot 0/3/0 (port 0/1) and I wanted to terminate both WAN and PSNT connection to the same gateway with MGCP protocol, and as I'm new to voice over IP world can anyone suggest/recommand me a proper guide which includes the stepts and proper explanations to acheive this task.
Thank you
Regards,
Suthakar

Hi Aman,
As discussed please find the attached output as follows,
#sh isdn status
Global ISDN Switchtype = basic-net3
%Q.931 is backhauled to CCM MANAGER 0x0003 on DSL 0. Layer 3 output may not apply
ISDN BRI0/0/0 interface
dsl 0, interface ISDN Switchtype = basic-net3
L2 Protocol = Q.921 0x0000 L3 Protocol(s) = CCM MANAGER 0x0003
    Layer 1 Status:
DEACTIVATED
    Layer 2 Status:
Layer 2 NOT Activated
    Layer 3 Status:
0 Active Layer 3 Call(s)
    Active dsl 0 CCBs = 0
    The Free Channel Mask: 0x80000003
%Q.931 is backhauled to CCM MANAGER 0x0003 on DSL 1. Layer 3 output may not apply
ISDN BRI0/0/1 interface
dsl 1, interface ISDN Switchtype = basic-net3
L2 Protocol = Q.921 0x0000 L3 Protocol(s) = CCM MANAGER 0x0003
    Layer 1 Status:
DEACTIVATED
    Layer 2 Status:
Layer 2 NOT Activated
    Layer 3 Status:
0 Active Layer 3 Call(s)
    Active dsl 1 CCBs = 0
    The Free Channel Mask: 0x80000003
ISDN BRI0/3/0 interface
dsl 12, interface ISDN Switchtype = basic-net3
    Layer 1 Status:
ACTIVE
    Layer 2 Status:
Layer 2 NOT Activated
    Layer 3 Status:
0 Active Layer 3 Call(s)
    Active dsl 12 CCBs = 0
    The Free Channel Mask: 0x80000003
%Q.931 is backhauled to CCM MANAGER 0x0003 on DSL 13. Layer 3 output may not apply
ISDN BRI0/3/1 interface
dsl 13, interface ISDN Switchtype = basic-net3
L2 Protocol = Q.921 0x0000 L3 Protocol(s) = CCM MANAGER 0x0003
    Layer 1 Status:
ACTIVE
    Layer 2 Status:
Layer 2 NOT Activated
    Layer 3 Status:
0 Active Layer 3 Call(s)
--More--                               Active dsl 13 CCBs = 0
    The Free Channel Mask: 0x80000003
    Total Allocated ISDN CCBs = 0
#sh ccm-manager
MGCP Domain Name: xxxxx.com
Priority        Status                   Host
============================================================
Primary         Registered               x.x.x.x
First Backup    None
Second Backup   None
Current active Call Manager:    x.x.x.x
Backhaul/Redundant link port:   2428
Failover Interval:              30 seconds
Keepalive Interval:             15 seconds
Last keepalive sent:            11:10:43 AEDST Nov 21 2013 (elapsed time: 00:00:11)
Last MGCP traffic time:         11:10:43 AEDST Nov 21 2013 (elapsed time: 00:00:11)
Last failover time:             None
Last switchback time:           None
Switchback mode:                Graceful
MGCP Fallback mode:             Enabled/OFF
Last MGCP Fallback start time: 05:28:32 AEDST Nov 18 2013
Last MGCP Fallback end time:    11:57:01 AEDST Nov 20 2013
MGCP Download Tones:            Disabled
TFTP retry count to shut Ports: 2
Backhaul Link info:
    Link Protocol:      TCP
    Remote Port Number: 2428
    Remote IP Address: x.x.x.x
    Current Link State: OPEN
    Statistics:
        Packets recvd:   3
        Recv failures:   0
        Packets xmitted: 5
        Xmit failures:   0
    BRI Ports being backhauled:
        Slot 0, VIC 0, port 1
        Slot 0, VIC 0, port 0
        Slot 0, VIC 3, port 1
Configuration Auto-Download Information
=======================================
Current version-id: 1384908973-2cefe363-d1ae-423b-a6ef-a85a0d4216af
Last config-downloaded:00:00:00
Current state: Waiting for commands
Configuration Download statistics:
Download Attempted             : 6
Download Successful          : 3
Download Failed              : 1
TFTP Download Failed         : 8428
Configuration Attempted        : 3
Configuration Successful     : 3
Configuration Failed(Parsing): 0
Configuration Failed(config) : 0
Last config download command: New Registration
FAX mode: disable
Configuration Error History:
Regards,
Suthakar

Not all executables will start from spawned batch (Is this a WinNT bug?).

I'm building a tool wherewith I can spawn a make process from my Visual Age for Java IDE.
This I have working now. However not all executables seem to get started from the batch.
Here are some of the from within the batch file started examples that work and won't work:
echo MakeBridge V1.00
echo Ensure that
echo %1%2
echo is a (sub) directory of
echo %JAVA_DEV_ROOT%
REM Usage: makeBridge <drive_letter> <working_directory> <make_command>
REM Change drive
%1 WORKS
REM Change directory
chdir %2 WORKS
REM Execute make command
echo ####%3#### WORKS
clearmake -C gnu %3 %4 %5 %6 %7 %8 %9 WON'T WORK
echo path=%PATH% WORKS
pwd WORKS
dir WORKS
java -version WON'T WORK
rem C:\APPL\_off97uk.32\Office\EXCEL.EXE WORKS
echo Marcel Zeeuw WORKS
The actual coding for the spawning is below:
Process p = Runtime.getRuntime().exec(batch);
// Pick up output stream from spawned process
BufferedReader br = new BufferedReader(
new InputStreamReader(p.getInputStream()));
String line;
while ((line = br.readLine()) != null)
System.out.println(line);
br.close();
System.out.println(p.exitValue());
Help would be appreciated
Kind regards,
Marcel Zeeuw.

Explicit naming of a path in front of a non-starting application doesn't help - as expected.
My conclusion is, that a process that is spawned by an application inherit some sort of limiting environment space. THis is because when I start my not working batch file from a command prompt, the batch file works as expected.
I have no solution for this problem for now...

Executing Csim start on a MGCP gateway

Similar Messages

Maybe you are looking for