Exhcnage 2010 send connector

our exchange 2010 smtp  send connector shows we are sending an smtp request to an unwanted address every 10 minutes. How does one determine with the session number listed who/what is initiating that request? 

Hi,
SMTP logging is disabled on Exchange server 2010 by default. I recommend you use the following cmdlet to enable protocol logging for the Send connector.
Set-SendConnector "xxx" -ProtocolLoggingLevel Verbose
For more information, here is an article for your reference.
Understanding Protocol Logging
http://technet.microsoft.com/en-us/library/aa997624(v=exchg.141).aspx
Hope it helps.
Best regards,
Amy Wang
TechNet Community Support

Similar Messages

  • Exchange 2010 Send Connector to postfix (v. 2.11) smarthost uses STARTTLS and cannot connect

    Dear all,
    I am having problems with exchange 2010 sending emails through a postfix smarthost server which disconnects the sessions. I also use a sendmail as a smarthost
    server which is working just fine but I have to switch to postfix and cannot do this as long as the encryption does not work.
    Here is the log file of the postfix server:
    Jan  4 14:18:59 server7 postfix/smtpd[1659]: initializing the server-side TLS engine
    Jan  4 14:18:59 server7 postfix/smtpd[1659]: connect from server1.mydomain.com[192.168.20.10]
    Jan  4 14:18:59 server7 postfix/smtpd[1659]: setting up TLS connection from server1.mydomain.com[192.168.20.10]
    Jan  4 14:18:59 server7 postfix/smtpd[1659]: server1.mydomain.com[192.168.20.10]: TLS cipher list "aNULL:-aNULL:ALL:+RC4:@STRENGTH"
    Jan  4 14:18:59 server7 postfix/smtpd[1659]: SSL_accept:before/accept initialization
    Jan  4 14:18:59 server7 postfix/smtpd[1659]: read from 7F4823FA5210 [7F4823FAB1B0] (11 bytes => -1 (0xFFFFFFFFFFFFFFFF))
    Jan  4 14:18:59 server7 postfix/smtpd[1659]: read from 7F4823FA5210 [7F4823FAB1B0] (11 bytes => 11 (0xB))
    Jan  4 14:18:59 server7 postfix/smtpd[1659]: 0000 16 03 01 00 5a 01 00 00|56 03 01                 ....Z... V..
    Jan  4 14:18:59 server7 postfix/smtpd[1659]: read from 7F4823FA5210 [7F4823FAB1BE] (84 bytes => 84 (0x54))
    Jan  4 14:18:59 server7 postfix/smtpd[1659]: 0000 54 a9 3d b9 0d 5e 8b 64|7c 6b b5 21 f2 93 e7 84  T.=..^.d |k.!....
    Jan  4 14:18:59 server7 postfix/smtpd[1659]: 0010 17 ea 33 d7 e5 13 f2 75|3a 87 38 32 01 85 82 5b  ..3....u :.82...[
    Jan  4 14:18:59 server7 postfix/smtpd[1659]: 0020 00 00 18 00 2f 00 35 00|05 00 0a c0 13 c0 14 c0  ..../.5. ........
    Jan  4 14:18:59 server7 postfix/smtpd[1659]: 0030 09 c0 0a 00 32 00 38 00|13 00 04 01 00 00 15 ff  ....2.8. ........
    Jan  4 14:18:59 server7 postfix/smtpd[1659]: 0040 01 00 01 00 00 0a 00 06|00 04 00 17 00 18 00 0b  ........ ........
    Jan  4 14:18:59 server7 postfix/smtpd[1659]: 0050 00 02 01                                         ...
    Jan  4 14:18:59 server7 postfix/smtpd[1659]: 0053 - <SPACES/NULLS>
    Jan  4 14:18:59 server7 postfix/smtpd[1659]: SSL_accept:SSLv3 read client hello A
    Jan  4 14:18:59 server7 postfix/smtpd[1659]: SSL_accept:SSLv3 write server hello A
    Jan  4 14:18:59 server7 postfix/smtpd[1659]: SSL_accept:SSLv3 write certificate A
    Jan  4 14:18:59 server7 postfix/smtpd[1659]: SSL_accept:SSLv3 write key exchange A
    Jan  4 14:18:59 server7 postfix/smtpd[1659]: SSL_accept:SSLv3 write server done A
    Jan  4 14:18:59 server7 postfix/smtpd[1659]: write to 7F4823FA5210 [7F4823FB8B70] (1911 bytes => 1911 (0x777))
    Jan  4 14:18:59 server7 postfix/smtpd[1659]: 0774 - <SPACES/NULLS>
    Jan  4 14:18:59 server7 postfix/smtpd[1659]: SSL_accept:SSLv3 flush data
    Jan  4 14:18:59 server7 postfix/smtpd[1659]: read from 7F4823FA5210 [7F4823FAC803] (5 bytes => 0 (0x0))
    Jan  4 14:18:59 server7 postfix/smtpd[1659]: SSL_accept:failed in SSLv3 read client certificate A
    Jan  4 14:18:59 server7 postfix/smtpd[1659]: SSL_accept error from server1.mydomain.com[192.168.20.10]: lost connection
    Jan  4 14:18:59 server7 postfix/smtpd[1659]: lost connection after STARTTLS from server1.mydomain.com[192.168.20.10]
    Jan  4 14:18:59 server7 postfix/smtpd[1659]: disconnect from server1.mydomain.com[192.168.20.10]
    I
    have read in the post at https://social.technet.microsoft.com/Forums/exchange/en-US/6db38364-cb08-45c0-b159-3ddf30ef0b3e/exchange-2010-send-connector-uses-ssltls-and-cannot-connect-to-smarthost-how-to-deactivate-ssl?forum=exchange2010
    how to deactivate the SSL encryption, but this is of course a security flaw, if I am not mistaken. I would like to encrypt the connection between the servers for obvious security
    reasons but I have come to a standstill...
    My Exchange server certificate is configured
    as follows:
    AccessRules        : {System.Security.AccessControl.CryptoKeyAccessRule, System.Security.AccessControl.CryptoKeyAcc
                         ule, System.Security.AccessControl.CryptoKeyAccessRule, System.Security.AccessControl.CryptoKe
                         essRule}
    CertificateDomains : {server1, server1.solid-con.com}
    HasPrivateKey      : True
    IsSelfSigned       : True
    Issuer             : CN=server1
    NotAfter           : 22/01/2017 13:18:02
    NotBefore          : 22/01/2012 13:18:02
    PublicKeySize      : 2048
    RootCAType         : None
    SerialNumber       : 6925D91285B649BD4D5E4297F1A48471
    Services           : IMAP, POP, IIS, SMTP
    Status             : Valid
    Subject            : CN=server1
    Thumbprint         : 939A37173BF84E352CEDC74F7D9A3D71F498A005
    AccessRules        : {System.Security.AccessControl.CryptoKeyAccessRule, System.Security.AccessControl.CryptoKeyAcc
                         ule, System.Security.AccessControl.CryptoKeyAccessRule}
    CertificateDomains : {WMSvc-SERVER1}
    HasPrivateKey      : True
    IsSelfSigned       : True
    Issuer             : CN=WMSvc-SERVER1
    NotAfter           : 19/01/2022 12:56:44
    NotBefore          : 22/01/2012 12:56:44
    PublicKeySize      : 2048
    RootCAType         : Registry
    SerialNumber       : 1DB8711F7ADC5CB54196468EF2FF5D21
    Services           : None
    Status             : Valid
    Subject            : CN=WMSvc-SERVER1
    Thumbprint         : 191D86BDE274510453D58DDB91D253DABBCF05F1
    And My Default Send Connector is configured as follows:
    AddressSpaces                : {SMTP:*;1}
    AuthenticationCredential     : System.Management.Automation.PSCredential
    Comment                      :
    ConnectedDomains             : {}
    ConnectionInactivityTimeOut  : 00:10:00
    DNSRoutingEnabled            : False
    DomainSecureEnabled          : False
    Enabled                      : True
    ErrorPolicies                : Default
    ForceHELO                    : False
    Fqdn                         :
    HomeMTA                      : Microsoft MTA
    HomeMtaServerId              : SERVER1
    Identity                     : Internet
    IgnoreSTARTTLS               : False
    IsScopedConnector            : False
    IsSmtpConnector              : True
    LinkedReceiveConnector       :
    MaxMessageSize               : unlimited
    Name                         : Internet
    Port                         : 25
    ProtocolLoggingLevel         : None
    RequireOorg                  : False
    RequireTLS                   : False
    SmartHostAuthMechanism       : None
    SmartHosts                   : {server7.mydomain.com, server6.mydomain.com}
    SmartHostsString             : server7.mydomain.com,server6.mydomain.com
    SmtpMaxMessagesPerConnection : 20
    SourceIPAddress              : 0.0.0.0
    SourceRoutingGroup           : Exchange Routing Group (DWBGZMFD01QNBJR)
    SourceTransportServers       : {SERVER1}
    TlsAuthLevel                 :
    TlsDomain                    :
    UseExternalDNSServersEnabled : False
    Any help would be greatly appreciated as I am
    stuck...
    Luca

    Hi Allen,
    Thank you very much for your reply.
    The Postfix TLS Manager is enabled in master.cf
    tlsmgr    unix  -       -       n       1000?   1       tlsmgr
    and running
    server7:/etc/postfix # ps -efa|grep tls
    postfix  11967 11863  0 11:21 ?        00:00:00
    tlsmgr -l -t unix -u
    Every other (Linux/UNIX) server has no problem e.g.:
    Jan  5 11:28:36 server7 postfix/smtpd[12215]: connect from server2.mydomain.com[192.168.20.20]
    Jan  5 11:28:36 server7 postfix/smtpd[12215]: Anonymous TLS connection established from server2.mydomain.com[192.168.20.20]: TLSv1 with cipher DHE-DSS-AES256-SHA (256/256 bits)
    Jan  5 11:28:36 server7 postfix/smtpd[12215]: B5502946AB0: client=server2.mydomain.com[192.168.20.20]
    Jan  5 11:28:36 server7 postfix/cleanup[12221]: B5502946AB0: message-id=<[email protected]>
    Jan  5 11:28:36 server7 postfix/qmgr[12200]: B5502946AB0: from=<[email protected]>, size=1026, nrcpt=1 (queue active)
    Jan  5 11:28:36 server7 postfix/smtpd[12215]: disconnect from server2.mydomain.com[192.168.20.20]
    Jan  5 11:28:37 server7 postfix/smtpd[12225]: connect from localhost[127.0.0.1]
    Jan  5 11:28:37 server7 postfix/smtpd[12225]: 4076A946AB1: client=localhost[127.0.0.1]
    Jan  5 11:28:37 server7 postfix/cleanup[12221]: 4076A946AB1: message-id=<[email protected]>
    Jan  5 11:28:37 server7 postfix/qmgr[12200]: 4076A946AB1: from=<[email protected]>, size=1778, nrcpt=1 (queue active)
    Jan  5 11:28:37 server7 postfix/smtpd[12225]: disconnect from localhost[127.0.0.1]
    Jan  5 11:28:37 server7 postfix/smtp[12222]: B5502946AB0: to=<[email protected]>, relay=127.0.0.1[127.0.0.1]:10024, delay=0.54, delays=0.05/0.01/0.01/0.47, dsn=2.0.0, status=sent
    (250 2.0.0 from MTA(smtp:[127.0.0.1]:10025): 250 2.0.0 Ok: queued as 4076A946AB1)
    Jan  5 11:28:37 server7 postfix/qmgr[12200]: B5502946AB0: removed
    Jan  5 11:28:37 server7 postfix/cleanup[12221]: 4401F946AB0: message-id=<[email protected]>
    Jan  5 11:28:37 server7 postfix/qmgr[12200]: 4401F946AB0: from=<[email protected]>, size=1920, nrcpt=1 (queue active)
    Jan  5 11:28:37 server7 postfix/local[12226]: 4076A946AB1: to=<[email protected]>, relay=local, delay=0.02, delays=0/0.01/0/0, dsn=2.0.0, status=sent (forwarded as 4401F946AB0)
    Jan  5 11:28:37 server7 postfix/qmgr[12200]: 4076A946AB1: removed
    Jan  5 11:28:37 server7 postfix/smtp[12227]: Untrusted TLS connection established to 192.168.20.10[192.168.20.10]:25: TLSv1 with cipher AES128-SHA (128/128 bits)
    Jan  5 11:28:37 server7 postfix/smtp[12227]: 4401F946AB0: to=<[email protected]>, orig_to=<[email protected]>, relay=192.168.20.10[192.168.20.10]:25,
    delay=0.29, delays=0/0.01/0.02/0.25, dsn=2.6.0, status=sent (250 2.6.0 <[email protected]> [InternalId=619] Queued
    mail for delivery)
    Jan  5 11:28:37 server7 postfix/qmgr[12200]: 4401F946AB0: removed
    and if you take a look at the lines in bold you will see that mails can be delivered over TLS to that very Exchange server (the mailboxes are on that server)...
    To summarise:
    exchange --> postfix with TLS = session disconnected (and everything seems to be initiated by the exchange server -if I read the logs correctly)
    postfix --> exchange with TLS = works
    any further hints?
    Thank you very much in advance,
    Luca

  • Exchange 2010 - Send Connector High Availability

    Hi All,
    I performed a successful migration a few years back from a single node Exchange 2003 server to a two node Exchange 2010 organisation with a DAG and Kemp load balanced CAS array.  The solution works well and when we simulate a site failure
    I am able to get the second node to handle all mail functions.
    The one problem I have though is that I have to manually disable the send connector on the primary server in order for the one on the secondary server to be in use.  I should explain that I have two send connectors as I do not want the secondary server
    to be used unless the primary server is down or the route is unavailable.  I realise that Exchange 2010 does not know whether the SMTP route is down or not so will just continue trying to use the send connector from the primary server (until I tell it
    not to by disabling it).
    My question is how do I get this to happen automatically?  Does anyone else have an example of how this could be done or use a PowerShell script to achieve this?  I guess a script could check the route and disable the send connector on the primary
    server if necessary, but how would one do this?
    Any help greatly appreciated.
    Rob

    Hi,
    According to your description, your secondary send connector cannot be automatically used when the first one is down. If I misunderstand your meaning, please feel free to let me know.
    If yes, I’d like to confirm if the settings of the secondary one is same with the first one and we can check the connectivity logs including diagnostic information for Healthy Server Selector.
    For more information, you can refer to the following article:
    http://technet.microsoft.com/en-us/library/ff634392(v=exchg.141).aspx
    Thanks,
    Angela Shi
    TechNet Community Support

  • Disable Send Connector BareLinefeedRejection

    Hi,
    Is it possible to disable BareLinefeedRejection for the Send Connector. similar to BareLinefeedRejectionEnabled for Receive Connectors?
    We sometimes receive emails with bare line feeds, but these emails are rejected by the send connector used for journalling.

    Hi,
    Base on my knowledge, it is impossible to edit bare line feed on send connector.
    It's by design that Exchange 2010 send connectors do NOT allow messages containing bare linefeeds to pass through.Bare line feeds aren’t allowed in SMTP communications. Although it may be possible for a message containing a bare line feed to be delivered
    successfully, such messages don't adhere to the SMTP protocol standards and may cause problems with messaging servers.
    Here is a similar thread for your reference:
    http://social.technet.microsoft.com/Forums/exchange/en-US/8da8d33a-fac8-4cc3-8ac0-6ea7f86ebfc4/exchange-2010-barelinefeedsareillegal-error-when-journaling-to-external-box?forum=exchange2010
    Thanks.
    Niko Cheng
    TechNet Community Support

  • Remove legacy Send connectors from Exchange 2010 after migration

    Hello.
    I have just removed the last legacy exchange 2003 server form our organisation.
    I followed the official MS documentation for this and the remove went to plan with no errors.
    The only issue I now have is that I have 2 legacy exchange send connectors in the Hub Transport view.
    I have tried to disable and remove them but I get an undocumented error. The warning I get in the exchange server event logs is as follows
    Process w3wp.exe () (PID=8148). Object [CN="Connector name",CN=Connections,CN="Organisation Name",CN=Routing Groups,CN="Group Name",CN=Administrative Groups,CN="Org Name",CN=Microsoft Exchange,CN=Services,CN=Configuration,DC="Domain
    Name",DC="local"]. Property [HomeMtaServerId] is set to value ["Domain Name"/Configuration/Deleted Objects/Microsoft MTA
    DEL:1bfa936f-c57e-4b7d-ad03-258acb560ad3], it is pointing to the Deleted Objects container in Active Directory. This property should be fixed as soon as possible.
    Is ADSI edit the best way to remove these entries or is there another way to disable and remove?
    Regards
    Lee Gregory

    Hi,
    If the legacy send connector is no longer needed, it is ok to remove it from ADSIEdit.
    For reference: select configuration as Connection point > domain > Services > MS Exchange > organizaiton name > Administrative Groups > Exchange Administrative Group > Routing Groups > First Routing Group > Connections 
    Regards,
    Rebecca Tu
    TechNet Community Support

  • How to create send connectors for multiple sites in the same domain?

    Current Scenario:
    We have 2 offices, 1 in London and 1 in India. Both are in the same domain and are connected via VPN. Both have their own separate Exchange 2003 server. Each location sends out their mail via the Default SMTP Virtual Server on their exchange server through
    their local ISP. There are no Send connectors created currently.
    We have now installed an additional Exchange 2010 server with Hub, CAS and Mailbox roles at the London site. Internal mail flow between the sites seems to be working fine.
    I believe the Exchange 2010 needs a Send connector to send out mail to the internet. However as soon as we create a Send connector on Exchange 2010, mail from the older 2003 servers at both sites start to flow out from the exchange 2010 server. This is not
    optimal for our India site since their outgoing mail now has to flow via the VPN to London and out via the new server.
    How can we configure it so that each server sends outgoing mail independently?
    Thanks

    Hi,
    In India site, you can create a SMTP connector which point to the local ISP.
    Thanks.
    Niko Cheng
    TechNet Community Support

  • Configure send connector for exchange online protection

    Hello Forum members,
    I am trying to configure send and receive connectors for Exchange 2010 to route
    on-premises mailboxes to Exchange OnLine Protection.  The "help" info MS provides
    is for Ex 2013 - and the EAC GUI and config does not lend a close fit to using the 2010
    Exch Management Console.  How can I configure connectors to properly connect to the Exchange Online Protection?
    I have seen where the ip addresses are posted, etc.  I am unclear how to configure the properties on the SBS 2011/EX 2010 server.
    Any tips will help,
    Thanks,
    Eric H.
    Network and Server Installs

    Hello Wesleyhe,
    You cannot use AD anything with EOP - if you mean exchange on-line protection.
    you have to set a smart host on the SBS server to connect to EOP, you may need to add the EOP server ips to your network config
    on the SBS server.  the smart host line (for the send connector on SBS server) is something like: yourdomainname-com.mail.protection.outlook.com.
    Then you need to configure the outside ip for your SBS server access in the EOP admin area.
    Hope this helps.
    eholz
    Network and Server Installs

  • Send connector in different costs

    Hi,
    All my exchange 2010 servers are in 1 single AD site.
    It seems not working when I configured item no 2.
    1. address => *, source server => hub A, cost => 1
    2. address => *, source server => hub B, cost => 100
    It is working if I joined Hub A & Hub B under send connector source server.  This configuration will send via HUB A or HUB B.
    My objective is to send to cost 1 as 1st proity.  Any additon configurations are needed?
    P/S: I was using this following for DR MBX and DR HUB
    Set-MailboxServer -Id: mbxserverA-SubmissionServerOverrideList: htserverB,htserverC
    Question: is it for all send and recived connectors?
    Please advise.  Thanks.
    Kelvin Teang

    Hi,
    Exchange must bind the send connector to a specific hub transport server in your Exchange organization. By default, Exchange chooses the server that you are creating the connector on, but you do have the option of specifying a different hub transport server.
    To meet your requirement, you should join both Hub A and Hub B under source server.
    About SubmissionServerOverrideList, Exchange Hub transport Server will be automatically load balanced within the Active Directory Site. Hub Transport Servers are load balanced in Round robin fashion within the Site. If you want to force Exchange Mailbox
    server to use specific Hub Server you need to make use of SUBMISSIONSERVEROVERRIDELIST.
    "Set-MailboxServer -Id: mbxserverA-SubmissionServerOverrideList: htserverB,htserverC"
    The command above will set Mailbox Server mbxserverA to use htserverB and htserverC for mailsubmission.
    Best regards,
    Belinda
    Belinda Ma
    TechNet Community Support

  • Is send connectors fault tolerant for source servers?

    Hi!
    I am in the process of applying SP3 on our Exchange 2010 environment. I have two Hubs that are both specified as source servers in our send connector to the internet. I just want to double check that when I'm applying SP3 to one of the server, that the other
    server is taking care of sending all emails. 
    My fear is that it is only load balancing so every other email will fail to be sent because on of the hubs are down.
    So can I safely update one of the servers and mail will be still sent from the other? Or should I just remove it as a source server from the send connector?
    I will of course redirect incoming emails to the hub that are up at the moment.
    Thanks!

    Hi ,
    Based on my knowledge while doing service pack upgradation on the hub transport severs there is no need to remove that particular server from source server list on the send connectors.
    In addition to that mail flow will load balanced across both the hub transport servers listed on the source server list .So on such case if anyone of the server in send connector's source server list is not funtional for the particular point of time then
    it will prefer the second funtional server to send emails to internet.Finally i would like to say that there wouldn't be an loss in emails.
    Thanks & Regards S.Nithyanandham

  • Two Send Connectors

    Hi,
    We have one MS-Exchange 2010 server and we have two hosted domains name it as abc.com and xyz.com (these domains are hosted at different ISPs) now i have configured SMTP connection to forwards all emails from exchange to abc.com and to forward emails from
    Exchange to abc.com requires Basic Authentication so i have configured it in send connector and all abc.com users are able to send their emails to other recipients.
    But the xyz.com users in our exchange server are not able to send their emails to external recipients because send connect is trying to authenticate to abc.com and mails are getting bounce. so i want to create second connector to forward xyz.com emails from
    my exchange server to xyz.com domain for authentication purpose and forward it further.
    In this case how exchange will recognize that xyz.com send connector is this and abc.com send connector is that ?
    Please provide me some solution on this?
    Arjun V.

    Create the two send connectors with different name spaces.
    one should be the catch all, for all email, with the * namespace.  The other is for the specific domain  xyz.com.
    Cheers,
    Rhoderick
    Microsoft Senior Exchange PFE
    Blog:
    http://blogs.technet.com/rmilne 
    Twitter:   LinkedIn:
      Facebook:
      XING:
    Note: Posts are provided “AS IS” without warranty of any kind, either expressed or implied, including but not limited to the implied warranties of merchantability and/or fitness for a particular purpose.

  • Exchange 2010 SMTP Connector

    Hello,
    We are having an issue with our exchange 2010 hub transport server and its external SMTP connector.  We use an external DNS CNAME as the smart host, this works on 2003 (As a FQDN of the host, not a smart host) but we receive DNS query failures on 2010.
    We can successfully route to the relay if we use an A record but an CNAME doesn't seem to work, is this as per design? Can we only use A records or IPs?
    Thanks

    You mean Send Connector, right?  (SMTP Connector is an Exchange 2000 or 2003 thing.)
    Are you sure you entered the CNAME correctly in the connector properties?  Can you ping the smart host or establish a telnet session over port 25?
    I've never heard of that issue before.  You might consider opening a ticket with Microsoft Support.
    Ed Crowley MVP "There are seldom good technological solutions to behavioral problems."

  • Send connector for forwarded emails not being used by Exchange 2013

    Hi we have 3 Exchange 2013 CU5 servers in a DAG setup and need to forward emails for some of the users to another domain. The problem is our outgoing spam filter seems to quarantine a lot of these emails which are  not spam. The problem is that I
    created a send connector for  the domain we are forwarding to (say contonso.com for illustrative purposes). Gave the send connector the name contonso.com, selected use MX record (didn't select Use the external DNS lookup settings on servers with transport
    roles) and added contonso.com in the address space gave it cost of 1. Added all the exchnage servers under source server. And clicked save. I then changed the cost to 2 on the main send connector with the domain as * which goes trhough our oput bound spam
    filter yet email I  send to one of the recipients with a forward inplace still go through that connector. Can anyone tell what i'm doing wrong or explain why this wouldn't work as expected ?   

    Easy question, did you enable the connector? :)
    Do you have more than one site in your org?
    DJ Grijalva | MCITP: EMA 2007/2010 SPA 2010 | www.persistentcerebro.com

  • Send connectors question

    Hi There,
    we have the 2 Ad sites and each site has the exchange server 2010 sp2 (HUB.MDB,UM and CAS). i want to route the messages based on Sites via each separate send connector. I would like to know send connectors use exchange cost routing to route the messages
    Many thanks
    David

    Under the send connector properties, scope it and then set the smarthost on each send connector to what you want. I assume that is what you are referring to.
    Note that there is *no* native source based routing in 2010.
    If you need source-based routing:
    If you want to use sender based routing in Exchange 2010, use an agent:
    http://routingruleagent.codeplex.com/
    or 3rd party software:
    http://ivasoft.com/routebysender.shtml
    http://grahamhosking.blogspot.com/2011/05/exchange-2007-2010-sender-based-routing.html
    http://technet.microsoft.com/en-us/library/aa997285(v=exchg.141).aspx
    Scoped send connector By default, all Send connectors that you create can be used by all the Hub Transport servers in your Exchange organization. However, you can limit the scope of any Send connector so that it can be used only by other
    Hub Transport servers that exist in the same Active Directory site. To limit the scope of this Send connector, select
    Scoped send connector.
    Twitter!:
    Please Note: My Posts are provided “AS IS” without warranty of any kind, either expressed or implied.

  • Send connector from exchange 2007

    Currently since I have both environments up, I see that Exchange 2013 is using the send connector that was created in my exchange 2007 environment.  Will this send connector go away once I bring down my exchange 2007 environment? Shoould I create
    a new one for Exchange 2013?

    Hi
    From what i have seen running ex2010 and upgrading to 2013 it stayed (exchange 2013 is clever :-)). you can just modify your send connector and make sure that the settings are for your exchange 2013 server.

  • How to send email to a SMTP server over a secure channel using STARTTLS setting of a send connector (Exchange and SMTP server are in the same domain)

    I’m trying to send email using exchange send connector STARTTLS setting to the SMTP server. I have read multiple documents on configuring TLS for send connector, but they talks about outbound connections to internet facing servers. My Exchange 2013 and SMTP
    server is in the same domain (let’s say A.com) and I’m creating dummy domains on my SMTP server (e.g.
    [email protected],
    [email protected] ) and their respective send connectors on the exchange server end. In the smart host section added the IP address of the SMTP server and in the scoping section added the SMTP domain address (e.g. dummy1.local ). In the FQDN field, added
    the FQDN of the exchange server 2013 which certificate is enabled with SMTP service.
    Could you tell me a step by step procedure, where I’m going wrong or any extra settings needs to added?
    Presently, it is giving me an error that 530 5.5.1 TLS encrypted connection is required.
    Note: I’ve created the Microsoft CA certificates for the SMTP and exchange servers and imported them in the personal certificate container. In which, the exchange certificate is created with FQDN name of the server and enabled for the SMTP service.
    I’m using OPENSSL certificate for making the SMTP server TLS enabled. (let me know, if I need to import the OPENSSL certificate anywhere on the exchange end)?
    Thanks!

    -IgnoreSTARTTLS is set to false on the send connector properties.
    I'm trying to established a HTTP over TLS connection. I'm not using mutual TLS between these two server.
    The send connector protocol logging is attached as below,
    2014-09-22T20:09:45.468Z,Exchange-SMTP send connector,08D1A4A14C7EDED5,2,10.219.3.74:24939,10.219.3.73:25,<,220 SMTP.A.local Welcome (MTA version),
    2014-09-22T20:09:45.546Z,Exchange-SMTP send connector,08D1A4A14C7EDED5,3,10.219.3.74:24939,10.219.3.73:25,>,EHLO Exchange.A.local,
    2014-09-22T20:09:45.624Z,Exchange-SMTP send connector,08D1A4A14C7EDED5,4,10.219.3.74:24939,10.219.3.73:25,<,250-SMTP.A.local Exchange.A.local OK,
    2014-09-22T20:09:45.624Z,Exchange-SMTP send connector,08D1A4A14C7EDED5,5,10.219.3.74:24939,10.219.3.73:25,<,250-SIZE,
    2014-09-22T20:09:45.624Z,Exchange-SMTP send connector,08D1A4A14C7EDED5,6,10.219.3.74:24939,10.219.3.73:25,<,250-8BITMIME,
    2014-09-22T20:09:45.624Z,Exchange-SMTP send connector,08D1A4A14C7EDED5,7,10.219.3.74:24939,10.219.3.73:25,<,250-BINARYMIME,
    2014-09-22T20:09:45.624Z,Exchange-SMTP send connector,08D1A4A14C7EDED5,8,10.219.3.74:24939,10.219.3.73:25,<,250-PIPELINING,
    2014-09-22T20:09:45.624Z,Exchange-SMTP send connector,08D1A4A14C7EDED5,9,10.219.3.74:24939,10.219.3.73:25,<,250-HELP,
    2014-09-22T20:09:45.624Z,Exchange-SMTP send connector,08D1A4A14C7EDED5,10,10.219.3.74:24939,10.219.3.73:25,<,250-DSN,
    2014-09-22T20:09:45.624Z,Exchange-SMTP send connector,08D1A4A14C7EDED5,11,10.219.3.74:24939,10.219.3.73:25,<,250-CHUNKING,
    2014-09-22T20:09:45.624Z,Exchange-SMTP send connector,08D1A4A14C7EDED5,12,10.219.3.74:24939,10.219.3.73:25,<,250-AUTH SCRAM-SHA-1 GSS-SPNEGO DIGEST-MD5 CRAM-MD5 NTLM,
    2014-09-22T20:09:45.624Z,Exchange-SMTP send connector,08D1A4A14C7EDED5,13,10.219.3.74:24939,10.219.3.73:25,<,250-AUTH=SCRAM-SHA-1 GSS-SPNEGO DIGEST-MD5 CRAM-MD5 NTLM,
    2014-09-22T20:09:45.624Z,Exchange-SMTP send connector,08D1A4A14C7EDED5,14,10.219.3.74:24939,10.219.3.73:25,<,250-STARTTLS,
    2014-09-22T20:09:45.624Z,Exchange-SMTP send connector,08D1A4A14C7EDED5,15,10.219.3.74:24939,10.219.3.73:25,<,250-DELIVERBY,
    2014-09-22T20:09:45.624Z,Exchange-SMTP send connector,08D1A4A14C7EDED5,16,10.219.3.74:24939,10.219.3.73:25,<,250-MT-PRIORITY,
    2014-09-22T20:09:45.640Z,Exchange-SMTP send connector,08D1A4A14C7EDED5,17,10.219.3.74:24939,10.219.3.73:25,<,250 ENHANCEDSTATUSCODES,
    2014-09-22T20:09:45.655Z,Exchange-SMTP send connector,08D1A4A14C7EDED5,18,10.219.3.74:24939,10.219.3.73:25,>,STARTTLS,
    2014-09-22T20:09:45.671Z,Exchange-SMTP send connector,08D1A4A14C7EDED5,19,10.219.3.74:24939,10.219.3.73:25,<,220 2.7.0 Ready to start TLS,
    2014-09-22T20:09:45.687Z,Exchange-SMTP send connector,08D1A4A14C7EDED5,20,10.219.3.74:24939,10.219.3.73:25,*,,Sending certificate
    2014-09-22T20:09:45.687Z,Exchange-SMTP send connector,08D1A4A14C7EDED5,21,10.219.3.74:24939,10.219.3.73:25,*,CN=Exchange.A.local,Certificate subject
    2014-09-22T20:09:45.687Z,Exchange-SMTP send connector,08D1A4A14C7EDED5,22,10.219.3.74:24939,10.219.3.73:25,*,"CN=DC-CA, DC=A, DC=local",Certificate issuer name
    2014-09-22T20:09:45.687Z,Exchange-SMTP send connector,08D1A4A14C7EDED5,23,10.219.3.74:24939,10.219.3.73:25,*,63E7E70100000000000B,Certificate serial number
    2014-09-22T20:09:45.687Z,Exchange-SMTP send connector,08D1A4A14C7EDED5,24,10.219.3.74:24939,10.219.3.73:25,*,CAEB1200CDF49715E5F2E4B8315EFDDC01F8F945,Certificate thumbprint
    2014-09-22T20:09:45.780Z,Exchange-SMTP send connector,08D1A4A14C7EDED5,25,10.219.3.74:24939,10.219.3.73:25,*,Exchange.A.local,Certificate alternate names
    2014-09-22T20:09:46.654Z,Exchange-SMTP send connector,08D1A4A14C7EDED5,26,10.219.3.74:24939,10.219.3.73:25,-,,Local
    2014-09-22T20:09:46.669Z,Exchange-SMTP send connector,08D1A4A14C7EDED6,0,,10.219.3.73:25,*,,attempting to connect
    2014-09-22T20:09:46.685Z,Exchange-SMTP send connector,08D1A4A14C7EDED6,1,10.219.3.74:24940,10.219.3.73:25,+,,
    2014-09-22T20:09:46.701Z,Exchange-SMTP send connector,08D1A4A14C7EDED6,2,10.219.3.74:24940,10.219.3.73:25,<,220 SMTP.A.local Welcome (MTA version),
    2014-09-22T20:09:46.701Z,Exchange-SMTP send connector,08D1A4A14C7EDED6,3,10.219.3.74:24940,10.219.3.73:25,>,EHLO Exchange.A.local,
    2014-09-22T20:09:46.716Z,Exchange-SMTP send connector,08D1A4A14C7EDED6,4,10.219.3.74:24940,10.219.3.73:25,<,250-SMTP.A.local Exchange.A.local OK,
    2014-09-22T20:09:46.716Z,Exchange-SMTP send connector,08D1A4A14C7EDED6,5,10.219.3.74:24940,10.219.3.73:25,<,250-SIZE,
    2014-09-22T20:09:46.716Z,Exchange-SMTP send connector,08D1A4A14C7EDED6,6,10.219.3.74:24940,10.219.3.73:25,<,250-8BITMIME,
    2014-09-22T20:09:46.716Z,Exchange-SMTP send connector,08D1A4A14C7EDED6,7,10.219.3.74:24940,10.219.3.73:25,<,250-BINARYMIME,
    2014-09-22T20:09:46.716Z,Exchange-SMTP send connector,08D1A4A14C7EDED6,8,10.219.3.74:24940,10.219.3.73:25,<,250-PIPELINING,
    2014-09-22T20:09:46.716Z,Exchange-SMTP send connector,08D1A4A14C7EDED6,9,10.219.3.74:24940,10.219.3.73:25,<,250-HELP,
    2014-09-22T20:09:46.716Z,Exchange-SMTP send connector,08D1A4A14C7EDED6,10,10.219.3.74:24940,10.219.3.73:25,<,250-DSN,
    2014-09-22T20:09:46.716Z,Exchange-SMTP send connector,08D1A4A14C7EDED6,11,10.219.3.74:24940,10.219.3.73:25,<,250-CHUNKING,
    2014-09-22T20:09:46.716Z,Exchange-SMTP send connector,08D1A4A14C7EDED6,12,10.219.3.74:24940,10.219.3.73:25,<,250-AUTH SCRAM-SHA-1 GSS-SPNEGO DIGEST-MD5 CRAM-MD5 NTLM,
    2014-09-22T20:09:46.716Z,Exchange-SMTP send connector,08D1A4A14C7EDED6,13,10.219.3.74:24940,10.219.3.73:25,<,250-AUTH=SCRAM-SHA-1 GSS-SPNEGO DIGEST-MD5 CRAM-MD5 NTLM,
    2014-09-22T20:09:46.716Z,Exchange-SMTP send connector,08D1A4A14C7EDED6,14,10.219.3.74:24940,10.219.3.73:25,<,250-STARTTLS,
    2014-09-22T20:09:46.732Z,Exchange-SMTP send connector,08D1A4A14C7EDED6,15,10.219.3.74:24940,10.219.3.73:25,<,250-DELIVERBY,
    2014-09-22T20:09:46.732Z,Exchange-SMTP send connector,08D1A4A14C7EDED6,16,10.219.3.74:24940,10.219.3.73:25,<,250-MT-PRIORITY,
    2014-09-22T20:09:46.732Z,Exchange-SMTP send connector,08D1A4A14C7EDED6,17,10.219.3.74:24940,10.219.3.73:25,<,250 ENHANCEDSTATUSCODES,
    2014-09-22T20:09:46.810Z,Exchange-SMTP send connector,08D1A4A14C7EDED6,18,10.219.3.74:24940,10.219.3.73:25,*,,sending message with RecordId 52652004081667 and InternetMessageId <[email protected]>
    2014-09-22T20:09:46.810Z,Exchange-SMTP send connector,08D1A4A14C7EDED6,19,10.219.3.74:24940,10.219.3.73:25,>,MAIL FROM:<> SIZE=7653 BODY=BINARYMIME,
    2014-09-22T20:09:46.810Z,Exchange-SMTP send connector,08D1A4A14C7EDED6,20,10.219.3.74:24940,10.219.3.73:25,>,RCPT TO:<[email protected]>,
    2014-09-22T20:09:46.825Z,Exchange-SMTP send connector,08D1A4A14C7EDED6,21,10.219.3.74:24940,10.219.3.73:25,<,530 5.5.1 A TLS-encrypted connection is required,
    2014-09-22T20:09:46.950Z,Exchange-SMTP send connector,08D1A4A14C7EDED6,22,10.219.3.74:24940,10.219.3.73:25,<,503 5.5.1 unexpected RCPT command,
    2014-09-22T20:09:46.981Z,Exchange-SMTP send connector,08D1A4A14C7EDED6,23,10.219.3.74:24940,10.219.3.73:25,>,RSET,

Maybe you are looking for

  • Report works on CR Developer XI but not on Crystal Reports Server

    I have a crystal report I created in Crystal Reports Developer XI that uses a command.  The code is as follows: select     supplier.supplier_sc, price_list.supplier_id, doc_line.doc_head_sc, product.product_id, product.product_n, price_list.unit_pric

  • Nitpicking about .properties file syntax

    After years of using these files, could someone please tell me what the convention for syntax is? :) This: somekey=valueor this: somekey = valueAnd YES, this must be the least important thread of all time, but since we're with multiple guys here mixi

  • My adobe flash play and adobe reader will not work!

    I can not get my adobe flash player or my adobe reader to work. I have reinstalled the software multiply times I have complete deleted all traces of the software and downloaded the newest version countless times. I even updated my IOS to Mountain Lio

  • Just tried to install a new app and was told that I needed to "Agree to new Terms

    Just tried to install a new app and was told that I needed to "Agree to new Terms & Conditions".  When I hit OK, it brings me to a blank screen, so I can't accept them.  What am I supposed to do?

  • URGENT:Changing Regional & Keyboard settings(language) thru Forms.

    Hello,      I need to do a screen in English/Spanish. The requirement is that, on the selection of the language from the menu the corresponding screen should come. The ORA and FRM messages, data entry and retrieval should also be in English or Spanis