Expansion Cards any particular order¿ KT4V

Im trying to pinpoint why my system hangs once ina while,, I have a hunch its the order of my expansion cards,, heres my current setup
Starting with AGP
AGP slot Asylum 256mb GeForce 5200 nvidia chipset "primary monitor"
1st PCI PCTV Card Pinnacle systems
2nd PCI Silicon Image Sil680 ATA/133 "primary channel=storage hard drive mostly multimedia content" "secondary channel=dvd-rom drive"
3rd Voodoo3 3dfx graphics card "secondary monitor"
4th Sound Blaster pci 128 sound card
5th Creative Modem Blaster V.92 DI5631
6th OHCI compliant IEEE 1394 FireWire Pinnacle systems
I dont know for sure but I am quessing I can put my expansion cards in a better sequence on the PCI bus, on my old mainboard I know I had a different order than I do now but I didn't pay attention when I pulled the cards was excited to get MSI mainboard setup,, I know the the 1st and 6th pci slots share ther same IRQs thats why I used the PCTV card 1st it is IRQ shared compatible, only when you are viewing TV not Capturing, so I felt that I would never capture from TV card and Firewire "on 6th PCI slot" at the same time,,, My main concern "or question" I have is the Sil680 PCI ATA/133, it should be placed accordingly so it doesn't ever hang up or conflict with the other expansion cards,, when my system hangs its always when it accesses one HD to the Other ,, main HD on primary channel mainboard and 2nd HD on primary channel Sil680 ,, this might not be my problem but any information on this would be greatly appreciated, I am trying to gain a better understanding of the PCI bus and card placement order, besides the IRQs So I can continue with my process of elimination and eventually solve my problem,, Thank You For Your Time In Reading This,,,,
Greatly Appreciated
~/\/\ike¥²

This Is my IRQ table from SiSoftware Sandra 2004 I think this is what you were asking for,
0 = System Timer
1 = Standard 101/102 keyboard
2 = Programmable interrupt controller
3 = COM2
4 = COM1
5 = COM4
6 = Standard Floppy Dsk COntroller
7 = ECP Printer port LPT1
8 = Sys CMOS real time clock
9 = IRQ holder PCI steering
9 = SoundBlaster PCI
9 = VIA PCI to USB enhanced host controller
10 = 3dfx voodoo3
10 = Creative PCI modem enumerator
10 = IRQ holder for PCI Steering
10 = IRQ holder for PCI Steering
10 = Primary Sil Ultra DMA Bus Master IDE Controller
10 = Sil PCI-0680 Ultra DMA IDE Controller
10 = OHCI Compliant IEEE 1394 host controller
10 = VIA Tech 3038 PCI to USB Universal Host COntroller
10 = VIA Tech 3038 PCI to USB Universal Host COntroller
11 = IRQ Holder for PCI Steering
11 = NVIDIA GeForce FX 5200
11 = Studio PCTV
11 = Studio PCTV (Audio)
11 = VIA Tech 3038 PCI to USB Universal Host Controller
12 = Microsoft PS/2 Mouse intellipoint
13 = Numeric data processor
14 = Primary IDE controller (dual fifo)
14 = VIA Bus Master PCI IDE Controller
15 = Secondary IDE controller (dual fifo)
15 = VIA Bus Master PCI IDE Controller
I am self taught on every aspect of my computer so I have a "grasp" of how and what IRQs are, but I am a spong to learn and am anxious to determine and correctly set up PCI bus and IRQs so I may better understand... so thank you very much for your time and help it is greatly appreciated!!

Similar Messages

How to add a specific order type into any particular report

Hi All,
How to add a specific document type(order type) into any particular report in order to review OTD performance.
I need to add one specific order type to existing reports which will help to check the performance of the delivery type for that particular order type to the users.
Thanks,
Raj

Hi Rajesh,
thanks for the reply when i tried as the way you said.. but the system is asking more details like varient. so if you can clearly specify the process for order type (VOV8-- table TVAK) so it will helpful for me.
Thanks
Raj

The artwork for our podcast, "Japan Baseball Weekly," recently disappeared. The RSS feed info appears to be in order, any particular reason for this and what can be done to rectify the situation?

The artwork for our podcast, "Japan Baseball Weekly," recently disappeared. The RSS feed info appears to be in order, any particular reason for this and what can be done to rectify the situation?

Please always post the URLs of the Store page and the feed when you have a question. For reference, your feed is at
http://www.japanesebaseball.com/services/jbw-podcasts.jsp
and the Store page is at
http://itunes.apple.com/gb/podcast/japan-baseball-weekly/id443149184
Looking at the Store page, the image appears there perfectly well. On subscribing there is no image associated with the episodes because you haven't embedded an image in the files - please see this page for clarification:
http://homepage.mac.com/rfwilmut/notes/coverart.html

Expansion card for Zire 31+ the file pdb.

Dear Madam/Sir.
I own a palm one handheld Zire 31 and I purchase an SD expansion card of 2.0 GB witch should fit, but my handheld does not recognize the card, what should I do? my second question is it necessary to download the file with the pdb suffix in order to add any Software? Thanks and best regards Gidi.
Post relates to: Zire 31

Hi, and welcome to the Palm Community Forums.
A 2GB expansion card will probably not work in the Zire 31. That model is limited to 1 GB cards. You might want to review this thread on the subject.
A .pdb file is a data file, whereas a .prc is an application file. What exactly are you referring to?
Post relates to: Centro (AT&T)
smkranz
I am a volunteer, and not an HP employee.
Palm OS ∙ webOS ∙ Android

KT4 Ultra: conflict w/ expansion cards

This is my first post, so please be gentle. I recently built new PC for photo editing and want to keep this old KT4 Ultra computer for general usage right beside. Both are running Windows XP Home SP3.
My KT4 computer had HDD crash and after replacement and fresh istallation of XP I initially had following expansion cards inside:
USB Expansion card (w/ 4 USB ports) on Slot 2 (INT B#)
Realtek RTL8139 Family PCI Fast Ethernet NIC on Slot 3 (INT D#)
Terratec EWX 24/96 Sound Card on Slot 6 (INT C#)
Everything was OK until I wanted a LAN connection for sharing of files (mostly) and Internet (via cable modem) between these two. Instead of a broadband wired router I opted for a Gigabit Ethernet card installing it on slot 5 (INT B#).
USB Expansion card (w/ 4 USB ports) on Slot 2 (INT B#)
Realtek RTL8139 Family PCI Fast Ethernet NIC on Slot 3 (INT D#)
D-Link DGE-528T Gigabit Ethernet Adapter on Slot 5 (INT B#)
Terratec EWX 24/96 Sound Card on Slot 6 (INT C#)
Somehow didn't want to have it on slot 1, so close to video card. Unfortunately after this the sound card was dropped by the system, a yellow question mark in Device Manager.
Further I failed to instal my Bluetooth Dongle which I earlier had used succesfully for communication to my mobile phone. Now my Broadcom USB Bluetooth Device is put under Unknown in Device Manager.
I did experience problems with the sound card several years ago in this very same PC. That time I knew little about system and BIOS setting and had to use another PC for audio purposes (digitalizing of tapes and vinyl).
As reference I used the PCI Interrup Request Routing table, found on page 2-32 in KT4's manual. Funny thing is that Sandra XI tells now that my two Ethernet cards having both INT pin A# while by their slots they should be B# and D#. I don't have true understanding what this means though. In BIOS the PNP/PCI Configurations has all slot IRQs on Auto.
Is this conflict easily cured by re-positioning card(s) on other slot(s) or addressing IRQ settings manually, and if so how and in which order? Or should I remove all the cards and install them in certain order...?
I'm quite exhausted as I had some component issues with my new PC and now this KT4 once again rejects my sound card. Maybe I'm better off by installing it on my new PC, but then this failure with Bluetooth dongle, (which I put on the USB port of KT4, not on the USB exp. card.) Oh my, why can't sound card and ethernet card live together!?!
I would appreciate your help very highly.

Hope you get things like you want them!
Eh, made this in 2003, but I'm not sure if it isn't more confusing than anything else:
"The use and sharing of IRQs aren't mentioned in my MSI manual, (due to the APIC function I think), so I had to go to some ASUS manuals. As standards are standards, I believe things can't be to different. If someone has any addings or suggestions please come forward, so I can adjust the table.
*Please note that this is generally speaking and mainly for ASUS boards a few years old!
**Please note that you should not have any sharing with the IDE controller or similar!
***Please note that it is a good thing to have expansion PCI sound cards in slot 3!
****Please note that surprisingly enough it looks like PCI slot 2 would be free for any device, but AGP cards get hot and bigger so it is not a great idea.
IRQ sharing table
PCI 1 shares with PCI slot 5
2 shares with AGP and PCI slot 6, or sometimes with onboard IDE
3 shares not, or sometimes with onboard audio/modem
4 shares with onboard LAN
5 shares PCI slot 1
6 shares with AGP and PCI slot 5
AGP slot shares with PCI slots 5 and 6
USB 1 shares with USB 2, 3 and USB 2.0
2 shares with USB 1, 3 and USB 2.0
3 shares with USB 1, 2 and USB 2.0
USB 2.0 shares with USB 1, 2, and 3
Onboard audio/modemshares not, or sometimes with slot 3
Onboard LAN shares with PCI slot 4
Onboard IDE shares not, or sometimes with PCI slot 2 "
Normally it is best to let Windows or whatever OS you run do the job. Setting IRQ:s yourself is a (too) big assignment.

Z87 XPower PCI_E2, Single Graphics Card plus Other Expansion Cards

A bit confused on the PCI-E expansion slots...
I seem to have read somewhere that it is preferential to place a single graphics card in PCI_E2 slot. Found a reference on a review:
"However for those using a single graphics card MSI recommends installing it in the second PCIe slot as this slot is connected directly to the CPU, meaning there is no latency lag as it bypasses the PEX 8747 chip"
However, the PCIe x16 Slots Bandwidth Table clearly shows only one "video card" (any other pci-e expansion card, too?) is possible when taking advantage of PCI_E2:
E1 E2 E3 E5 E7
Single: 0 x16 0 0 0
2-Way: x16 0 0 x16 0
3-Way: x8 0 x8 x16 0
4-Way: x8 0 x8 x8 x8
I picked up a pci-e OCZ RevoDrive 3 x2 SSD 240GB and looking to use a N770 graphics card in PCI_E2... is this even possible? Ideally, I would choose to run the RevoDrive from PCI_E1.
From reading the table, I get "no".
I called MSI support, and 2 agents seemed to believe the PCIe x16 Slots Bandwidth Table only related to graphics cards ("The table below shows the correlation between the PCIe slots bandwidth and multiple
graphics cards."). Still waiting an official response to ticket(s). I spoke with the first before I began my graphic card installation, and the second after I installed and couldn't get the RevoDrive to show in any slot when the graphic card was installed in PCI_E2.
My experience is telling me I have a problem, and I have some decisions to make moving forward. Generally speaking:
1. Is it possible to install a single graphics card in PCI_E2 to bypass the PEX 8747 chip and achieve x16 bandwidth, and still have another pci-e in another x8/x16 slot?
2. What is more important for the video card: x16 bandwidth, or "latency lag as it bypasses the PEX 8747 chip"?
3. The performance of the RevoDrive is outstanding (knock on wood... hoping I can keep this card running a long time considering the volume of drive failures experience with OCZ drives). I am considering my overall day-to-day usage and wondering if I might be better off ditching the RevoDrive or the graphic card... or (oh my, GOD!) another board....
It is easy for me to criticize engineering for overlooking this potential design consideration, yet it is an outstanding board. I should have been more aware when I read the 0-16-0-0-0 config details on the PCIe x16 Slots Bandwidth Table and the detail on the PEX 8747 chip. Once of the major items that attracted me to the XPower was the heap of features and pci-e expandability. Yet, all the PCI-E bandwidth and slots don't do me any justice if I can't config my install to optimize my system's components.
I would have a hard time trying to pick another to even try to replace the Z87 XPower (it would have to be Asus Z87-DELUXE).
What would I lose or gain in keeping the RevoDrive vs the graphic card? I initially began building this system around the RevoDrive, and I can't imagine wanting to keep the system without it.
4. What am I sacrificing/gaining in having the graphic card in PCI_E1 and the RevoDrive in PCI_E5?
5. With two different x16 pci-e components installed, and only one of them a graphic card, does the PEX 8747 chip latency become a non-issue? Is it still preferential to keep the graphic card in PCI_E2 position?
PSU: Corsair AX1200i
CPU: i7-4770k
MOBO: Z87 XPower
VGA: MSI GTX N770 Lightning 2GB
SSD: RevoDrive 3 x2 240GB
RAM: Generic 1333 (special ordered Corsair Dominator 2400MHz)
Thanks for any additional insight and clarity!

1: connecting a single card in PCI_E2 will bypass the PLX8747 but if you use one of the other slots for something it will start to use the PLX chips again to duplicate lanes!
2: PCI-E lanes are of very little importance as you will only see a .1 to 2FPS reduction in frame rate between x16 and x8. and less lag is similar in that regard too and will have very little noticeable difference!
3: it should make very little difference to either component and changing board makes in the z87 family lines would make very little difference too as to get higher expandability you need that PLX chip to sub divide the lanes and create a extra 16 fake lanes to allow more then 2 way SLI or 3 way Crossfire on the Z87 boards as the CPU's only have 16 lanes total!
4: not much! about a hundred nanoseconds of lag, maybe 1MBP/s less on the revo drive and .1 to 2 FPS less on the Graphics card...
5: no you would need them in the E1 and E5 positions and using the PLX chips as you will have problems and both may go into x8 using only the CPU's 16 lanes total if the Graphics card is in E2 or the revo drive may not function at all as the graphics card may hog all the PCI-E lanes....

How to load data in a particular order ?

Hi
I am trying to load data from an oracle view to a oracle table. Its working fine.
However the problem is, the load is not in a particular order. I mean the order
in which the data is loaded in target table is not fixed. It means sometimes
a particular data value (say row1 ) comes before another data value(say row2)
and again executing the interface second time may not follow the same order.
I have a requirement to load it in a specific order.
Please reply.
Regards
Manoj

Hi Surya
Thanks for the quick reply and its working as well.
But I am still unable to solve the problem I made the above changes for.
Actually, I am loading members for a particular dimension from an oracle
view(say view1) to an oracle table(say table1). I have created a view(say view2)
from this table1.The reason to create the view2 is to use the logic
ORDER BY ,CONNECT BY PRIOR to sort the stored/shared members.
Now I am using this view2 to load members for a dimension in planning.
On first execution, it executes without any error. But on executing it again, it throws
many errors, most of which say Cannot load dimension member, error message is:
com.hyperion.planning.HspRuntimeException: Move would result in base member being
a sibling of a corresponding shared member
This error occured previously as well.I mean before using an ORDER BY in my first interface,
ie loading from view1 to table1.
Kindly help me to resolve the problem.
Regards
Manoj.
Edited by: 908458 on Mar 1, 2012 7:30 AM

How to exclude "Blocked for Purchase" error message in PO creation for particular Order Type

In Article master some times we used to set Site-Specific Article Status = '01'. (MARC-MMSTA)
01
Blocked for Purchase
02
Blocked for Purchase/Sale
My requirement is that when Creating PO in ME21N for a particular Order Type (Purchasing). This check need to be removed.
Now if we try creating the PO we will be getting the below error message.
Status "Blocked for Purchase" of article XXXXXX does not allow external procurement.
Is there any exit or BADI where i can put logic to remove this check.

Hi ,
You can use BADI ME_PROCESS_PO_CUST or customer exist EXIT_SAPMM06E_013
Regards,
Pravin

Audigy Platinum EX expansion card/external drive prob

I have used this card for home studio recording and gaming for a while with no problems. I recently built a new PC and now cannot get the external dri've or expansion card to work. The sound card works otherwise. Games, CD, wave files, and plugs on back of card work correctly. I just cannot get the any input through the external dri've to work. All connections have been checked and double checked. The card has been uninstalled and reinstalled both physically and through device manager. Drivers have also been uninstalled and reinstalled.
Help.

Marcos69,
Are you getting a red light in the optical out port on the EX dri've? If not it may be that the power lead connected to the card itself is not working. You may want to try another one if possible. Gi'ven the double checking that you have already done, if this doesn't help then you may have a dead dri've. You can contact support to arrange a repair if needed.
Jeremy

How Do I Save Tracks in A Particular Order In My Playlists?

I want to save music from my Library to my Playlist in my order and not by itunes check boxes or default. For some reason I cannot move them around in my Playlist to play in a particular order say for instance a Wedding or Funeral. itunes only has default orders that I can see. I can't seem to move particular tracks up or down and save in that order. Is this possible?

This can be done by sorting on the leftmost column (with the numbers).
Then you can drag them at any position you want.
Shuffling for that playlist has to be off.
Hope this helps.
M

Payment terms not modifiable in PO for particular order type

Hi Gurus
My client wants the payment terms should not be modified while creating a PO. It should be picked from vendor master. But this requirement is for a particular order type ZIN only. I tried in SPRO but then it is affecting all the order types. Is there any user exit or solution for this.
Regards,
Yuvaraj

Hi,
STEP 1:
Spro>Materials Management>Purchasing>Purchase Order>Define Screen Layout at Document Level
Create a new " Field Selection Key" for ur doc type
(ex: Standard NB doc type the "Field Selection Key" would be "NBF", you can make a copy of it)
Just Double click on that
then click on "Terms of delivery and payment", there you can see the "Terms of payment" field.
against that field you can see three options, Reqd.entry Opt. entry Display...
Here tick the field "Display", So that You will get this field display only for the document type ZIN.
STEP 2:
Spro>Materials Management>Purchasing>Purchase Order>Define Document Types
Here Assign the newly created "Field Selection Key" against the your PO doc type ZIN

I want to order files (e.g., photos) in a particular order (not necessarily an order that is an option in MacOS. Ie, my own custom order, and I want them STAY in that order until I change the order. Is this possible?

I want to order files (e.g., photos) in a particular order (not necessarily an order that is an option in MacOS. Ie, my own custom order, and I want them STAY in that order until I change the order. Is this possible?

Custom sort order is not a typical option in the list view of any desktop computing systems I know of. The way you're seeing it work is also how it works in Windows and other systems.
There is no "None" sort order. What you're seeing is a "None" option under "Arrange By." Arranging is not the same as sorting; arranging is how the files are grouped in the window. For example, you can arrange (group) files by Kind while sorting by Name. You'll notice that if you are in List view and you choose Arrange By "None," in the window there is still a sort triangle next to the column name that it's sorting by.
If Arrange is set to None, the files appear in one big group (the traditional view) that is controlled by the Sort order (where there is no None option).
I didn't even know the difference between Sort and Arrange until I saw your question and did a little research! This Macworld article helped:
How to arrange and sort files in Lion Finder (also applies to later OSs like Mavericks)
As for your main question, how to do a custom sort order in the Finder, you can only rearrange files manually in Icon view. As with other operating systems, if you want to create a custom sort order for photos there are other ways:
Use a photo organizer application like iPhoto or Lightroom. Some let you have custom sort orders in folders, but others only let you have a custom sort inside a different container like an "album" or "collection". Having those additional container types is part of why photos are often best managed in an organizer application and not on the desktop.
Rename the files. You can use a renaming utility program to rename the photos with numbers that will enforce your sort order when sorted by name on the desktop, like
01 Photo.jpg
01 Photo.jpg
01 Photo.jpg
or
Photo 01.jpg
Photo 02.jpg
Photo 03.jpg

Adding View Criteria Row attribute in a particular order

Hello friends,
We are using the Jdeveloper version 11.1.2.3.0.
We are populating the Query component filter programmatically , we want to show the filter order in a particular way.
The following is the code.
ViewCriteriaManager vm = view.getViewCriteriaManager();
oracle.jbo.ViewCriteria vca[] = vm.getAllViewCriterias();
oracle.jbo.ViewCriteria vc = vca[0];
vc.removeAllElements();
ViewCriteriaRow vcr = vc.createViewCriteriaRow();
vcr.setAttribute("A", "");
vcr.setAttribute("B", "");
vcr.setAttribute("C", "");
vcr.setAttribute("D", "");
vc.add(vcr);
vc.saveState();
view.applyViewCriteria(vc, true);
vm.criteriaChanged(vc);
But the filter is shown in the Query component in the following order.
C,A,B,D
Is there any way to add a filter in particular order?
Thanks in advance.
Best Regards,
Vijay

Sounds like your users are tough. You can provide your own ViewCriteriaAttributeHintsImpl and override the behaviour of HINT_NAME_FIELD_ORDER.
Create a custom ViewRowAttrHintsImpl class
public class CustomViewRowAttrHintsImpl extends ViewRowAttrHintsImpl {
@Override
public String getHint(LocaleContext locale, String sHintName) {
if (HINT_NAME_FIELD_ORDER.equals(sHintName)) {
//calculate and return field order here
return super.getHint(locale, sHintName);
}Generate a ViewRowImpl and return your custom class in createViewRowAttrHints
@Override
protected ViewRowAttrHintsImpl createViewRowAttrHints(AttributeDefImpl attrDef) {
return new CustomViewRowAttrHintsImpl(attrDef, this);
}

Disabling all fields in VA02 on a particular Order status

Hi Gurus,
We have a requirement to grey out all the fields of the sales order in VA02 if the current order header status is
set to a particular value , lets say '10' (E0010).
I have tried below code in MV45AFZZ (userexit_field_modification) :
IF sy-tcode = 'VA02' AND vbak-auart = 'ZTIL'.
    CALL FUNCTION 'STATUS_READ'
      EXPORTING
        client           = sy-mandt
        objnr            = vbak-objnr
        only_active      = 'X'
      TABLES
        status           = lt_stat
      EXCEPTIONS
        object_not_found = 1
        OTHERS           = 2.
    DELETE lt_stat WHERE stat CP 'I*'.
    READ TABLE lt_stat INTO lw_stat WITH KEY stat = 'E0010'.
    IF sy-subrc EQ 0.
      LOOP AT SCREEN.
        screen-input = 0.
        MODIFY SCREEN.
      ENDLOOP.
    ENDIF.
ENDIF.
But, the issue is here the program goes for a long endless loop
and eventually we have to stop the transaction.
(since we did not want to choose any particular field, but grey out entire order)
Could anyone of you please suggest what needs to be done here.
Thanks in advance.
Regards,
Nitin

Hi Nitin,
You didn't mention that you want that two fields to be open.
What you have done is correct in the form routine but you should not use Loop at screen. Because the Form routine is itself called for each field.
The following code logic change inside the userexit_field_modification will solve your problem.
Write like;
IF sy-tcode = 'VA02' AND vbak-auart = 'ZTIL'.
CALL FUNCTION 'STATUS_READ'
EXPORTING
client = sy-mandt
objnr = vbak-objnr
only_active = 'X'
TABLES
status = lt_stat
EXCEPTIONS
object_not_found = 1
OTHERS = 2.
DELETE lt_stat WHERE stat CP 'I*'.
READ TABLE lt_stat INTO lw_stat WITH KEY stat = 'E0010'.
IF sy-subrc EQ 0.
IF SCREEN-NAME NE 'FIELDNAME1' AND SCREEN-NAME NE 'FIELDNAME2'.
screen-input = 0.
MODIFY SCREEN.
ENDIF.
ENDIF.
ENDIF.
There is no need for trasaction variant and all if this works.
Regards,
Karthik D
Edited by: Karthik D on Feb 3, 2011 4:05 PM - Corrected code

Expansion Card can't be read

Hey I've just bought a new tungsten E2 handheld device and bought with it a 2 GB expansion card, but the device can't seem to be able to read it. it's brand is kingston and it doesn't appear whatsoever in the card info.
Can you help me plz
thanks
Post relates to: Tungsten E2

The maximum size card the E2 can accept is 1GB. The 2GB will not work.
Here is a link to the Palm webpage for the card sizes.
http://www.palm.com/cgi-bin/cso_kbURL.cgi?ID=34080
Here is a link to the Palm knowledge library. Here you can select your device and do a search for articles regarding your particular question.
http://kb.palm.com/SRVS/CGI-BIN/WEBCGI.EXE?New,Kb=PalmSupportKB
Here is a link to the support webpage for your device.
http://www.palm.com/us/support/tungstene2/
Post relates to: Palm i705

Expansion Cards any particular order¿ KT4V

Similar Messages

Maybe you are looking for