Experincing issues with 2960X switch

Hi there.
We are experincing issues with 2960X switch losing the ability to recognise the modules that are inserted in SFP ports.
Initially, the modules are recognised, usable and will happily participate in cross-stack etherchannels. However, after a period of time -  and this ranges from a couple of hours to a few days, the links go down on the 2960X-side but are still registered as up on at the other end of the etherchannel.
2960X stack  1      Po1(SD)         LACP      Gi3/0/49(D) Gi3/0/51(D)
3750G stack  2      Po2(SD)         LACP      Gi1/0/23(I) Gi2/0/22(I)
When the link fails, the member switch loses the ability to identify modules inserted - it knows they are there, but it cannot identify them. Having a look at the controller for one of them and it's having trouble,see below:-
sh controllers ethernet-controller gi3/0/49 phy detail
GigabitEthernet3/0/49 (gpn: 457, port-number: 49)
hulc_sfp_iic_intf_read_eeprom sfp _index 0 yeti_iic_read_retry fail
hulc_sfp_iic_intf_read_eeprom sfp _index 0 yeti_iic_read_retry fail
hulc_sfp_iic_intf_read_eeprom sfp _index 0 yeti_iic_read_retry fail
A 'sh int' gives:-
Auto-duplex, Auto-speed, link type is auto, media type is unknown.
Reboot the stack or just the member and everything resets and works again - for a period of time. I've swapped from compatible to Cisco-brand modules inbetween restarts and it doesn't prevent the issue reoccuring.
The slots all fail at the same time and once they're in the error state, that switch has to be restarted before it will recongnise anything inserted in any slot.
I have this issue on two seperate stacks in two different sites. We're running 15.0(2)EX4.
Has anyone seen anything like this? Particularly interested in this which I've seen using the sh controllers cmd and on the console once after a reboot. hulc_sfp_iic_intf_read_eeprom sfp _index 0 yeti_iic_read_retry fail
Any thoughts would be greatly appreciated.
Aid

Hi Team
We happen case GLC-T with Catalyst 2960 Hang , It can't work 
We was reload switch but same ( GLC-T with Catalyst 2960 Hang)
and use command bellow  
Switch97#
Switch97#
Switch97#sh int gi 1/0/26 transceiver 5 transceiver de
Switch97#sh int gi 1/0/25 transceiver detail 
hulc_sfp_iic_intf_read_eeprom sfp _index 0 yeti_iic_read_retry fail
hulc_sfp_iic_intf_read_eeprom sfp _index 0 yeti_iic_read_retry fail
hulc_sfp_iic_intf_read_eeprom sfp _index 0 yeti_iic_read_retry failDiagnostic Monitoring is not implemented.
Switch97#
Switch97#
Switch97#sh int gi 1/0/25 transceiver detail 6 transceiver        de
Switch97#sh int gi 1/0/26 transceiver detail 
hulc_sfp_iic_intf_read_eeprom sfp _index 1 yeti_iic_read_retry fail
hulc_sfp_iic_intf_read_eeprom sfp _index 1 yeti_iic_read_retry fail
hulc_sfp_iic_intf_read_eeprom sfp _index 1 yeti_iic_read_retry failDiagnostic Monitoring is not implemented.
We try IOS Software EX3, EX4, EX5 and 15-2.2 but can't problem 
Please suggest case to me

Similar Messages

  • Routing Issue with 3550 Switch

    I am having an issue with routing with one of my Cisco 3550 switches.  I know the 3550s are EoL but some of us have to work with what we have.
    I am using a 3550 on either side of a Layer 2 link.  The Layer 2 link is 2 Extreme Summit X-440 switches with Microwave between the switches.  I have a VLAN configured on both switches and tagged on the ports connected to the Microwave.  The 3550 switch on each end is configured for IP routing but I cannot pass traffic between the switches.  If I unplug the switch on the local end and plug in a laptop, I can ping the switch on the remote end and access devices at the remote end. 
    I know this should work because I am doing the same thing over another Microwave link and Layer 2 link using another 3550 and a HP ProCurve at the remote end.
    Here are the configs for each 3550:
    Local end;  Port Fa0/23 goes to the Remote Side.  Port Fa0/24 goes to the rest of the network
    Current configuration : 5417 bytes
    ! No configuration change since last restart
    version 12.2
    no service pad
    service timestamps debug datetime localtime show-timezone
    service timestamps log datetime localtime show-timezone
    no service password-encryption
    service sequence-numbers
    hostname Brindley3550
    enable secret 5 $1$3A.n$lzBUQg.fn4hJ7f0jEOqe71
    no aaa new-model
    clock timezone UTC -6
    clock summer-time UTC recurring 1 Sun Apr 2:00 1 Sun Nov 2:00
    mls qos map cos-dscp 0 8 16 26 32 46 48 56
    mls qos min-reserve 5 170
    mls qos min-reserve 6 10
    mls qos min-reserve 7 65
    mls qos min-reserve 8 26
    mls qos
    ip subnet-zero
    ip routing
    ip domain-name morgan911.net
    ip name-server 1.2.150.11
    ip name-server 1.2.150.5
    spanning-tree mode pvst
    no spanning-tree optimize bpdu transmission
    spanning-tree extend system-id
    vlan internal allocation policy ascending
    interface FastEthernet0/1
     switchport access vlan 18
     switchport mode dynamic desirable
     spanning-tree portfast
    {Removed for Brevity}
    |
    interface FastEthernet0/7
     switchport access vlan 13
     switchport mode dynamic desirable
     spanning-tree portfast
    interface FastEthernet0/8
     switchport access vlan 13
     switchport mode dynamic desirable
     spanning-tree portfast
    {Removed for Brevity}
    interface FastEthernet0/23
     description To Gum Springs via Extreme P10
     no switchport
     ip address 1.2.147.1 255.255.255.252
     speed 100
     duplex full
    interface FastEthernet0/24
     description To Flint via Ceragon Eth 2
     switchport trunk encapsulation dot1q
     switchport mode trunk
     speed 100
     duplex full
     mls qos trust cos
     auto qos voip trust
     wrr-queue bandwidth 20 1 80 1
     wrr-queue min-reserve 1 5
     wrr-queue min-reserve 2 6
     wrr-queue min-reserve 3 7
     wrr-queue min-reserve 4 8
     wrr-queue cos-map 1 0 1 2 4
     wrr-queue cos-map 3 3 6 7
     wrr-queue cos-map 4 5
     priority-queue out
     spanning-tree link-type point-to-point
    interface GigabitEthernet0/1
     switchport trunk encapsulation dot1q
     switchport mode trunk
    interface GigabitEthernet0/2
     switchport access vlan 10
     switchport trunk native vlan 50
     switchport mode dynamic desirable
     spanning-tree portfast trunk
    interface Vlan1
     ip address 1.2.145.2 255.255.255.0
    ip default-gateway 1.2.145.1
    ip classless
    ip route 0.0.0.0 0.0.0.0 1.2.145.1
    ip route 1.2.165.0 255.255.255.240 1.2.147.2
    ip route 1.2.166.0 255.255.255.240 1.2.147.2
    ip http server
    snmp-server community public RO
    snmp-server community public/RO RO
    snmp-server location Brindlee Mountain Tower Site
    snmp-server contact Jamey Wright
    snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
    snmp-server enable traps cluster
    snmp-server enable traps entity
    snmp-server enable traps envmon fan shutdown supply temperature
    snmp-server enable traps vtp
    snmp-server enable traps vlancreate
    snmp-server enable traps vlandelete
    snmp-server enable traps flash insertion removal
    snmp-server enable traps port-security
    snmp-server enable traps config
    snmp-server enable traps syslog
    snmp-server enable traps mac-notification
    snmp-server enable traps vlan-membership
    snmp-server host 1.2.150.100 public  tty envmon syslog snmp
    control-plane
    ntp clock-period 17180143
    ntp server 1.2.150.21
    end
    And this is the config for the remote end.  Port Fa0/24 is the port for the link back to the local end.
    Current configuration : 5058 bytes
    version 12.2
    no service pad
    service timestamps debug datetime localtime show-timezone
    service timestamps log datetime localtime show-timezone
    no service password-encryption
    service sequence-numbers
    hostname GS3550
    enable secret 5 $1$3A.n$lzBUQg.fn4hJ7f0jEOqe71
    no aaa new-model
    clock timezone UTC -6
    clock summer-time UTC recurring
    mls qos map cos-dscp 0 8 16 24 32 46 46 56
    udld aggressive
    ip subnet-zero
    ip routing
    ip domain-name morgan911.net
    ip name-server 1.2.150.11
    spanning-tree mode pvst
    spanning-tree extend system-id
    vlan internal allocation policy ascending
    interface FastEthernet0/1
     switchport access vlan 21
     switchport mode dynamic desirable
     spanning-tree portfast
    interface FastEthernet0/2
     switchport access vlan 21
     switchport mode dynamic desirable
     power inline delay shutdown 20 initial 300
     spanning-tree portfast
    {Removed for Brevity}
    interface FastEthernet0/23
     switchport access vlan 22
     switchport trunk encapsulation dot1q
     switchport mode trunk
     speed 100
     duplex full
     spanning-tree portfast
    interface FastEthernet0/24
     description To Brindlee via Extreme P10
     switchport mode dynamic desirable
    (Is a member of VLAN 1)
     speed 100
     spanning-tree portfast
    interface GigabitEthernet0/1
     switchport trunk encapsulation dot1q
     switchport mode trunk
    interface GigabitEthernet0/2
     switchport mode dynamic desirable
     spanning-tree portfast
    interface Vlan1
     ip address 1.2.147.2 255.255.255.252
    interface Vlan21
     ip address 1.2.165.1 255.255.255.240
     ip helper-address 1.2.150.11
     ip helper-address 1.2.150.5
    interface Vlan22
     ip address 1.2.166.1 255.255.255.240
     ip helper-address 1.2.150.5
     ip helper-address 1.2.150.11
    ip default-gateway 1.2.147.1
    ip classless
    ip route 0.0.0.0 0.0.0.0 1.2.147.1 10
    ip http server
    snmp-server community public RO
    snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
    snmp-server enable traps cluster
    snmp-server enable traps entity
    snmp-server enable traps envmon fan shutdown supply temperature
    snmp-server enable traps vtp
    snmp-server enable traps vlancreate
    snmp-server enable traps vlandelete
    snmp-server enable traps flash insertion removal
    snmp-server enable traps port-security
    snmp-server enable traps config
    snmp-server enable traps hsrp
    snmp-server enable traps bridge newroot topologychange
    snmp-server enable traps syslog
    snmp-server enable traps mac-notification
    snmp-server enable traps vlan-membership
    snmp-server host 1.2.150.100 public  envmon syslog snmp
    control-plane
    ntp clock-period 17180192
    ntp server 1.2.150.21 key 0 prefer
    Ideas?  Anything stand out as grossly wrong?  I have worked on this for 2 days and am at a loss.
    Thanks
    Jamey

    Sorry for the delay in replying.  Other items at the office took priority over this project.  I tried that and no change.  I pulled the switch from the remote site and took it back to the local end and connected the switches with a crossover cable and everything works fine.  I have pretty much determined that it is an issue with the config in one of the Extreme switches.  The config in those look pretty normal but there are a few things I am unsure of.  Guess I'll see if there is a similar site for Extreme gear.
    Thanks
    Jamey

  • Netbooting issue with Netgear switches

    Hi,
    We’ve started having issues with Netbooting since we recently replaced our network hardware, going from very old (10 yrs +) 3Com switches running at 100MB to desktop / 1GB backbone to brand new Netgear switches at 1GB desktop / 10GB backbone.
    On the old network hardware Netbooting would work fine, showing a list of Netboot images that we are able to boot from with no issue (mainly used for DeployStudio). We have two Mac servers on our network, and now, rather than being able to get a list of Netboot images, it seemingly selects one of the two “Default” images (one for each server) at random. Whichever image is selected works correctly, but we now have no way of choosing at time of bootup.
    Other than replacing the switches, nothing else has changed (that I am aware of) that could have caused this to stop working. However, some relevant info:
    The new Netgear switches are generally M5300-52G-POE+ with a small number of XSM7224S.
    Spanning Tree is enabled on the switches (set to Rapid Spanning Tree – 802.1w). Have also tried with STP turned off totally as I understand this may make a difference – however it did not.
    The infrastructure is a mixed network, with both Windows PC’s/Servers sitting on the same network as the Macs. DHCP is supplied by one of the Windows servers.
    No VLAN’s are set up – all running on same network.
    Both Mac servers are sitting in different physical locations on the network. One is running 10.9.4 and the other on 10.6.8
    If I boot holding down Option then I only see the local hard disk.
    If I boot holding down either N or Option N then the Mac boots using one of the two Default Netboot images, seemingly at random, from one of the two Mac servers. This is as expected for Option N, but N alone used to bring up a list of images (including those not selected as the default on either server).
    All the netboot images show up correctly within the Startup Disk option within System Preferences. I can then boot successfully from any of them in this manner, and am therefore able to get round my problem in the short term, but of course this isn’t ideal.
    I have tried setting the netinstall images to be available both over HTTP and NFS, but this has no effect. Also there are no access restrictions in place for any of the images.
    I’m not 100% convinced that the issue is related to swapping to Netgear switches. Particularly as no specific configuration was ever done on the old 3Com switches to get netboot working (it just worked from the start). Also, the new switches are so much quicker than the old ones. That said it seems far too coincidental that this started happening when the switches were swapped over, and that as I said before, nothing else has changed.
    If there’s anything anyone can suggest that I can check, both with the switch configuration or otherwise, I’d be really grateful.
    Finally, just to say I’m more a Windows person than a Mac man, so treat me gently J
    Cheers,
    LSDWho

    NetBoot uses DHCP to look for available NetBoot servers so when you hold down just N at boot time it sends a DHCP query asking NetBoot servers to advertise themselves. This might therefore suggest the issue is DHCP related. (Strictly speaking NetBoot uses BSDP - Boot Service Discovery Protocol.)
    Note: This use of DHCP by NetBoot does not normally conflict with a real full-blown DHCP server which would ignore this type of query. So it should not cause an issue with your Windows DHCP server.
    Since it might be DHCP related I would look at the following -
    http://kb.netgear.com/app/answers/detail/a_id/21984/~/what-is-a-dhcp-l2-relay-an d-how-does-it-work-with-my-manged-switch%3F
    http://kb.netgear.com/app/answers/detail/a_id/21990/~/how-do-i-configure-a-dhcp- l3-relay-using-the-web-interface-on-my-managed-switch%3F
    I would then see if you can disable DHCP relay functionality and also any other related features like DHCP filtering. If you have not already done so it might be worth checking for any firmware updates and installing those as often 'new' switches out of the box will have shipped with older firmware.

  • Oracle Forms 6i/11i Apps: Horizontal scroll bar is hiding last record in the form, issue with folder switcher

    Horizontal scroll bar is hiding last record in the form. Attached the screenshot which shows the issue.
    Regards,
    Venkat K

    If this is a custom form, you will have to alter the design. If this is a seeded form, pl open an SR with Support

  • Issues with MW600 switch between paired devices

    Hi, I've got an MW600.
    When paring  then connecting it to my phone (N95 8GB) it just works fine.
    When pairing then connecting it to my lenovo laptop it just works fine.
    But the switch of the MW600 between both of my devices is simply not working. When connected to my phone, it switches sound to the laptop but not the microphone;
    When connected to the Laptop, it's even worst: it does not switch at all to my phone.
    The only solution I've got found is to pair again to the one I want to switch to. Which is unacceptable, as thi switch function has been sold as the differentiator vs many other BT stereo earphones.
    Can anybody for SonyEricsson help?
    Many thx

    I think what you would have to push and hold the call key on the headset to switch between devices that uses microphone. The use the volume key to select device.
    I you like to switch between media devices you press and hold the play key.
     - Community Manager Sony Xperia Support Forum
    If you're new to our forums make sure that you have read our Discussion guidelines.
    If you want to get in touch with the local support team for your country please visit our contact page.

  • After iOS 6.1 - Issue with auto-switching from 3G to LTE

    After updating my iPhone 5 to iOS 6.1 it is not switching automatically between 3G and LTE on the AT&T network.  It has happened a few times today where the phone goes to 3G, and it will not switch back to LTE unless I toggle Airplane mode.  Any ideas other than restarting the phone and resetting network settings?

    I have the same type of problem. I leave my phone in the same place all day & most of the time it has 3G but then loses it and goes on Edge which *****.
    Why does it do this?

  • WRT54G Dropping Out With EZXS88W Switch Plugged In

    Hey everyone.  The issue that I am having is that when I connect my Linksys EZXS88W switch into the WRT54G router, the router keeps crapping out on me.  What it does is that all of the lights go out on the router, then comes back on every minute or so.  What could cause this to happen?  The router works perfectly fine when the switch is unplugged from the router.  I also connecte the swtich to the router through the normal port, as well as using the uplink port, but alas, the same results occur.
    Could there be a specific setting on the router that I need to configure so that the router communicates properly with the switch?  Also, the switch is brand new, right out of the box.  I figured it would have been just plugging it in, and away it goes.  Sadly, that is not the case.
    Any help would be greatly appreciated!

    From what you described I assume it's the issue with your switch because if you don't connect the switch your router works fine...Your switch does not even have a reset button...
    You can however power cycle the router and then the switch when you connect them both...

  • Logitech Keyboard Issues with Fast User Switching

    I'm running OSX 10.4 on an 800 MHz iMac, and using a Logitech Cordless Navigator keyboard. The keyboard's main feature (for me) is the ability to have the function keys (F1-F12) automatically open applications and folders and such. When I have multiple accounts running though, this feature seems to be tied to whichever one I first logged into. If I switch accounts and try to use one of the keyboard shortcuts nothing happens where I am, but when I switch back to the original account I find that the keyboard has opened the program there. The keyboard types fine in the new account, and I can even change the preferences so the function keys do different things in the different accounts, but the extra functionality seems to be only available for whichever account logs in first.
    I realize this may just be a Logitech bug, but any ideas how to fix this? (Also even though I'm the only one using my computer this seems like a mild security issue, if theoretically another user could activate programs on my account without the password.)
    800 MHz iMac G4   Mac OS X (10.4.3)   768 MB RAM

    Logitech support is frustrating:
    Dear tajmahall14,
    Thank you for your recent inquiry about your Keyboards.
    I understand you are having issues with the settings for the function keys becoming non-functional when fast switching from one user account to another.
    Depending on the system configuration, the Fast User Switching may or may not work. Unfortunately this is not an issue I can address. You may need to contact Apple to see if they have a possible solution to your problem.

  • I had to uninstall Firefox for diagnostic reasons on my Dell desktop, and am having hundreds of issues with shortcuts now. I want to get it perfectly operational with IE, then switch back to Firefox

    I was having minor registry issues after switching to Firefox, and Dell suggested going back to IE to see if that cured the problem. Upon uninstalling Mozilla, and reinstalling IE, none of the desktop shortcuts worked in fact, a partial window opened, and locked up the screen. Dell suggested contacting you to find out if maybe the uninstall did not work completely.
    Any suggestions?

    It most definitely is the browser that is causing most of the problems. I have used Firefox so long, I can't even remember. Maybe since its beginning. But today is a sad day. I gave up on it. I can't accomplish anything and end up spending hours troubleshooting. I see I am not alone. I am so sick of it "not responding." It's simply not worth it to spend so much time trying to make the thing work, so I can actually do something. Installed, removed, reinstalled numerous times, and I can't fix your software on my Win 7 Pro machine. No problems with IE or Chrome. So. as much as I hate Google Update, Chrome has won the test. Sad, sad day for me to lose Firefox, but it just does not work on the Win 7 machine. I don't have the same issues with the XP machine and have exactly all the same add-ons. Keep it up developers and you will have no Win 7 users at all.

  • Issues with a SGE2000 switch

    It seems that the SGE2000 switch will lose the connections of systems after some period of time. I will ping a system and it will be slow or will not reply at all. See example below: C:\>ping 10.1.16.16 Pinging 10.1.16.16 with 32 bytes of data: Reply from 10.1.16.16: bytes=32 time=102ms TTL=63 Reply from 10.1.16.16: bytes=32 time1ms TTL=63 Reply from 10.1.16.16: bytes=32 time1ms TTL=63 Reply from 10.1.16.16: bytes=32 time1ms TTL=63 Ping statistics for 10.1.16.16: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 102ms, Average = 25ms C:\>ping 10.1.16.16 Pinging 10.1.16.16 with 32 bytes of data: Reply from 10.1.16.16: bytes=32 time1ms TTL=63 Reply from 10.1.16.16: bytes=32 time1ms TTL=63 Reply from 10.1.16.16: bytes=32 time1ms TTL=63 Reply from 10.1.16.16: bytes=32 time1ms TTL=63 Ping statistics for 10.1.16.16: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms I have made two changes; 1)The Aging Interval 630 the max. 2)Static MAC address entry. But nether of these changes have helped. Has anyone see issue with the SGE2000 switch? Thanks

    Thanks for the info. I have the latest firmware on the switch and resetting it doesn't help. I am route 7 IP networks via this switch with 24 systems on each network. I have statically added some of the systems MAC addresses to see if that would help, but same issue.

  • I am having issues with MLBtv, when I switch on my ATV it no longer comes up as an option nor does vimeo or the iTunes store, i've tried resets etc and after those they appear. put the tav into sleep mode and mysteriously they don't re appear. Any ideas?

    I am having issues with MLBtv, when I switch on my ATV it no longer comes up as an option nor does vimeo or the iTunes store, i've tried resets etc and after those they appear. put the tav into sleep mode and mysteriously they don't re appear. Any ideas?

    I am having the same issue but mine is with Netflix.  And there are only 4 categories now on the main menue when there used to be 5.  Something went crazy with ATV software.

  • I just switched from iphone 4s to LG G3. I'm having issues with bluetooth in my car, iphone would sync automatically but with G3 I have to manually connect to my car's bluetooth every time I turn it on - it won't sync automatically. Any fixes?

    I just switched from iphone 4s to LG G3. I'm having issues with bluetooth in my car, iphone would sync automatically but with G3 I have to manually connect to my car's bluetooth every time I turn it on - it won't sync automatically. Any fixes?

    You can turn on BT tethering but it disables Wifi so if I have to do that step every time I get in my car, I just as well manually connect on BT every time.

  • I am using pages designing a flow chart, question "I seem to have an issue with the arrows that you can add text to, it appears I can not move the point of the arrows up or down they only switch from left to right.

    I am using pages designing a flow chart, question "I seem to have an issue with the arrows that you can add text to, it appears I can not move the point of the arrows up or down they only switch from left to right.

    Last point...who archives? On my regular email page I now have the Archive icon to the left of my Delete icon which I would prefer was to the left, first in the line as this is the icon I use mostly. With Folders, my Sent and Trash lists, who needs to archive?
    I can help you only with the placement of the icon placement -- if you right-mouse click on the toolbar, then select Customize Toolbar, you can move an icon to where you want it to be.

  • We recently switched ISPs. To connect to the new ISP our Airport Extreme has to be in bridge mode. Now our Nintendo Wii won't connect to the Airport. Is it an issue with bridge mode that is causing this?

    We recently switched ISPs. To connect to the new ISP our Airport Extreme has to be in bridge mode. Now our Nintendo Wii won't connect to the Airport. Is it an issue with bridge mode that is causing this? We're running two Macs wirelessly with no problems.  And the Wii did connect before the switch.

    Hello and thanks for the reply.  I gave this a try, turned off Airport on one of the computers and tried the Wii again.  Still no connection.  I should say that we're also running an old G4 (wired) off the Airport as well, with no problems.  I've tried many things to make the Wii to work, including power cycling the Airport, turning off the security settings in the Airport, resetting the Airport to it's default and redoing the network, resetting the network setting on the Wii (several times), moved the Airport closer to the Wii, all with no luck.  The Wii "sees" the Airport but won't connect to it.  I'm at a loss for anything else to try, so any help is appreciated.

  • HT1695 Anyone else having issues with not being able to get wifi on their iPhone 4S? I can't even switch the wifi button to try and connect to my wifi at home but my iPad still uses the wifi just fine.

    I can't even switch the wifi button to try and connect to my wifi at home but my iPad still uses the wifi just fine.

    Thank you, I am trying to last option now. Resetting my network settings and if that still doesn't work ill have to go in to the apple store. Hopefully I won't need a new phone because I'm already at my limit with replacements on my AppleCare even though the issue with the phones 3 out of 4 times wasn't my fault and I can't afford to buy another phone.

Maybe you are looking for

  • YTD and MTD for different scenarios

    Hello, i'm looking for a possibility to upload actual figures as YTD value and Forecast figures as MTD value. The point is that i don't want to have another dimension to defferentiate between two ways of data input (we have already 12 dimensions :-(

  • Custom field html displays as text

    I am converting a custom field from a SharePoint 2007 version to SharePoint 2013. The field works correctly in SP2007. In SP2013 it has the correct information but displays as text instead of html. I have set the "disable-output-escaping" in the xsl

  • Can't open Lightroom.  Keep getting application error - unable to start correctly (0xc000007b).

    Keep getting application error - unable to start correctly (0xc000007b).  Have uninstalled and reinstalled twice with no change.

  • Control checkbox in basic list

    I have write a checkbox in basic list and i have created a status for the list, and when i click the checkbox it doesn´t works to the event at line-selection, i have tried with the hide command too, but it doesnt goes to the event, i think that it go

  • Read a 3D-PDF with a Mac?

    My boss just got an Apple MacBook Pro with OSX, and has installed Acrobat reader 7.0.8 He sees the image but can't rotate the 3D-PDF I have sent him. http://3d.onlinestoragesolution.com/PDF_3D-Solid/FS-11-008_3D.pdf I had the impression that this was