Exposure Control setting for HDR

I know RAW can contain multiple exposures within the format, but when taking RAW images, when shooting for HDR what should the exposure range be set to 3 photos or 5 photos and;
-0.5 to + 0.5 EV ?
- 1EV to +1 EV ?
-2 EV to +2 EV ?

Depends also if you are using the new Adobe Camera RAW or the new Lightroom (6) or CC2015.
The newest software has some fantastic new ways of combining for HDR. With the new ACR and Lightroom, I have found that 2 to 4 images depending on the dynamic range of the scene, will work well. I have gotten fantastic results with 2 images in the new software, compared to doing the same HDR in the older versions of Photoshop. Just make sure that YOU expose for the highlights in one image and then for the shadows in the other. If you are letting your camera do the AEB, auto exposure bracketing, then try 2 stops. However if you see your three images either too dark or too light (highlights blown in both or shadows dark in both, then try adjusting the settings. Hope that makes sense

Similar Messages

  • How to make JOB CONTROL setting for delta extraction in Production system .

    Hello All,
    We are in the process to transport our development to PD server in BI . We have transported the data sources to ECC production and now we are filling the setup table for " SD BILLING BW " . After filling Setup table data in full mode through infoPackage we have to load data in delta mode .    
    How we can set our Update mode(LBWE setting) in PD server ?
    Is LBWE  T.Code authorisation required in ECC PD server to make the setting of Update mode   or   We have to set all  Job Control Paramater in Dev System at the time of transport the datasource request to ECC production .  Is our time which is set in job control of  ECC development  will be reflected in ECC production ?
    can any body tell me about how to make setting for delta extraction in Production system .
    Thanks ...

    Hi,
    How do you load the data in the development system?
    - you set up the update mode in the infopackage. There you must customize "Initialization"
    - you have to filled the setup table in the production system without laoding the data in the BW? then this step was for nothing. Filling the setup table and do the INIT in the BW, this must be together - during no changing will be done in your R/3 SD.
    Sven

  • Problems in Copy Control Setting for Collective invoice..

    I need the  invoice which combines different deliveries  provided the sold to party is same and the delivery date is same. Right now I m using standard routine 11 in the copy control which splits if the purchase order is different or the city code is different. So I need another routine which should remove the splitting criteria.
                The required splitting criteria should be
                1 – Different Sold to parties
                2- Different Delivery date
                3- Different Plant
    Otherwise it should combine the deliveries into one invoice.
    Regards,
    Subho

    Hi Subhasish,
    It's not just ZUKRI - it could be any field and since 011 does not form ZUKRI it isn't in your case. What I'd suggest is:
    1. Create your own Data Transfer Routine as a copy of 011.
    2. Assign it in VTFF.
    3. clear fields that create a split
    Also check partners, because the city code, must come from a partner which is assigned to the header. In case this is unwanted, assign this partner function to item procedure, rather than the header and you'll avoid the split.
    regards,
    Stratis

  • Lightroom Exposure Control

    Can I use LRs exposure control slider for the same function as it is used in my camera? I'd like to get additional shots but only have a -3, 0 and a +3 on the camera. I'm doing some photos in High Definition Imaging and want to increase the number if shots I put together with the HDL software...

    There's a long story here, but the bottom line is -3 to +3 is plenty, and doing what you are proposing won't work nearly as well as doing it in-camera.

  • HT4759 i downloaded the icloud to my pc it says to login with apple id and it says it is a valid apple id but not cloud but i cannot get the control panel for icloud to come up to set it up on my pc which runs windows 8

    i downloaded the icloud to my pc it says to login with apple id and it says it is a valid apple id but not cloud but i cannot get the control panel for icloud to come up to set it up on my pc which runs windows 8

    An update.
    From iCloud Control Panel 2.1.1 for Windows
    "iCloud Control Panel 2.1 and later includes support for Windows 8"
    but you still need to set it up on a Mac or iOS device, "Note: To create an iCloud account you need an iPhone, iPad, or iPod touch with iOS 5 or later, or a Mac with OS X Lion v10.7.5 or later."

  • Any Way to Set Default Settings for HDR Toning?

    I have developed a nice set of parameters for the HDR Toning feature and have saved them as Noels Defaults, but I don't see a way to make them the default settings for HDR Toning.  Frankly I find the default color settings for the tool very garish.  I suppose that's good, because it always reminds me that I need to select my own settings, but...
    Can you suggest a way to make my own settings the HDR Toning dialog defaults, so as to save a step each time I use it?
    My apologies if I'm being dense and missing something obvious.
    Thanks.
    -Noel
    P.S., I'm on Windows 7 by the way, and of course I'm talking about Photoshop CS5.

    Thanks Zeno.
    Well, then, Adobe, could you please make the defaults settable, for example like Camera Raw?
    Thank you.
    -Noel

  • Please provide the patch set for Oracle Enterprise Manager Grid Control 10

    Hi,
    please provide the patch set for Oracle Enterprise Manager Grid Control 10.2.0.1 and 10.2.0.5 for AIX 5.3
    patch set for Oracle Enterprise Manager Grid Control for 11.2.0.2 OS AIX 5.3
    Thanks,
    Vishal Hande.

    user12009184 wrote:
    Hi,
    please provide the patch set for Oracle Enterprise Manager Grid Control 10.2.0.1 and 10.2.0.5 for AIX 5.3
    patch set for Oracle Enterprise Manager Grid Control for 11.2.0.2 OS AIX 5.3
    Thanks,
    Vishal Hande.you must obtain all patches directly from
    http://support.oracle.com

  • Control key is set for u2018Process mfg

    Hi ALL,
    Which control key is set for u2018Process mfg., Inspection, AutoGRu2019

    Hi,
    Adding to the information given by srini,You can find the config setting for each control key in OPJ8 (Tcode)
    If needed you can create your own control keys here & use the same in the Master recipe
    Regards,
    SVP

  • Control key is set for u2018Process manufacturing with Inspectionu2019

    Hi,
    Which control key is set for u2018Process manufacturing with Inspectionu2019?
    What is the meaning of FS Relationship

    Hi,
    Control Key for "Process manufacturing with Inspection" is PI02.
    It is meant for Manufacturing is with Process Order with Quality inspection.
    Further this Control key you need to set in CR01/CR02 -Default Values-> Operation Default Values----> Control Key
    Regards,
    Tejas
    Edited by: Tejas  Kantilal Pujara on May 21, 2008 8:54 AM

  • Control/set a limit for file attachment

    Hello,
    I would like to know if there is a way to control/set a limit for file attachment in Workbench ES. e.g. Assign Task > Attachments & Notes.
    Can you please advise.
    Thanks,
    Han Dao

    No. You would have to customize Workspace to do that.
    Jasmin

  • Transport request for Set Control Parameters for Actual Data.

    Hi Viewers,
    I am unable to create the transport request for the below settings
    Controlling->Profit Center Accounting->Basic Settings->Controlling Area Settings->Activate Direct Postings->Set Control Parameters for Actual Data.
    Is it possible to move the request through transport request or do we need to create the settings directly in the target system.
    Thanks
    Aswin.

    Hi,
    Please read the IMG help at the given path.  There are certain profit center accounting settings which cannot be transported directly from the same path, but there is another node in SPRO path for doing this.  If possible I will try to locate the path but I am not sure I can post it immediately as I am not having system handy.
    thanks,
    Kumar

  • What is STB Remote Control code for the Magnavox 15MF400T/3​7 set?

    Does anyone know or know where to find the correct remote control code for the 15MF400T/37 set?

    If none of the codes worked, your only other option is to do a scan.
    WHAT IF NONE OF THE CODES WORKED?
    If none of the codes worked, try the following procedure. (As before, we will use the example of a TV. For other devices use the appropriate Device Key instead of the
    TV
    key in step 2 and 3.) 
    1. Turn on your TV.
    2. Press and hold the TV key.
    3. While holding down the TV key, press OK
    4. Release both keys. The Device Keys will blink twice.
    5. Press 9 - 2 - 2
    6. Point the remote at the TV.
    7. Press the play button 
    8. Press FF button . Every time you press the FF button the remote sends out a new power-off command to the TV. Keep pressing FF until the TV turns off.
    9. When the TV turns off, you have found the right code. Press OK  to store this code.
    Note: There are over 300 TV and DVD codes. The most common codes are tried first, but you may still need to press FF over 300 times to find the right code. If you reach the end of the list of codes the entire remote will flash twice and return to normal operation. You can exit programming at any time by pressing EXIT 
    If you do this and it still doesnt work, then your tv and the verizon remote dont have a common code and it will not work with your tv.
    ====================================================================================
    Error exists between keyboard and chair.

  • Copy control setting regarding DN for STO

    Hi gurus,
    When I create outbound delivery note for cross-plant POs, the items cannot be showed in one D/N as the delivery date on the PO are different.
    When I change them to the same date, they can be showed in one D/N.
    The copy control configuration for the item is: 303 (item data for data transfer)
    I tried others item data choices and was still not right.
    I want to make the same POu2019s item in the same outbound D/N. How can I make it?
    Thanks in advance.

    Hi Subhasish,
    It's not just ZUKRI - it could be any field and since 011 does not form ZUKRI it isn't in your case. What I'd suggest is:
    1. Create your own Data Transfer Routine as a copy of 011.
    2. Assign it in VTFF.
    3. clear fields that create a split
    Also check partners, because the city code, must come from a partner which is assigned to the header. In case this is unwanted, assign this partner function to item procedure, rather than the header and you'll avoid the split.
    regards,
    Stratis

  • Exposure adjustment layer for 32 bit HDR images

    I know I can adjust exposure in Camera Raw. I can use the adjustment brush to make local exposure adjustments in ACR too. Is it possible to make exposure adjustments to 32 bit images in Photoshop? My attempts at using the exposure adjustment layer weren't successful. Although I'm told "exposure" was designed for 32bit, the adjustment layer doesn't seem to be to access and manipulate any of the exposure data thats I know is in the file, but is not visible. It would be should be so useful, but from what I gather the exposure adjustment is totally useless for 32 bit images. Are I doing something wrong? 

    Thanks for the reply. I'm struggling to explain so i'll try and illustrate instead. Basically the Exposure adjustment layer does not work on the 32 bit file in the same way that ACR does. ACR changes exposure in the predictable way it should (like a raw file). The Exposure adjustment layer in photoshop doesn't work the same way. Or at all?

  • Photoshop's brightness and exposure controls?

    Can anyone explain the difference(s) between Photoshop's brightness control and its exposure control?
    Thanks,
    Mark

    Did it ever occur to you to consult the documentation, Mark. Say, the User Guide and/or the Help files?
    Exposure command
    Adjusts tonality by performing calculations in a linear color space. Exposure is primarily for use in HDR images. See Adjust Exposure for HDR image.
    Adjust Exposure for HDR images
    Comments (0)
    The Exposure adjustment is designed for making tonal adjustments to HDR images, but it works with 8‑bit and 16‑bit images. Exposure works by performing calculations in a linear color space (gamma 1.0) rather than the current color space.
    1. Do one of the following:
    Click the Exposure icon or an Exposure preset in the Adjustments panel.
    Choose Layer > New Adjustment Layer > Exposure.
    Note: You can also choose Image > Adjustments > Exposure. But keep in mind that this method makes direct adjustments to the image layer and discards image information. Adjustment layers for 32-bit images are available in Photoshop Extended only.
    2. In the Adjustments panel, set any of the following options:
    Exposure
    Adjusts the highlight end of the tonal scale with minimal effect in the extreme shadows.
    Offset
    Darkens the shadows and midtones with minimal effect on the highlights.
    Gamma
    Adjusts the image gamma, using a simple power function. Negative values are mirrored around zero (that is, they remain negative but still get adjusted as if they are positive).
    The eyedroppers adjust the luminance values of images (unlike the Levels eyedroppers that affect all color channels).
    The Set Black Point eyedropper sets the Offset, shifting the pixel you click to zero.
    The Set White Point eyedropper sets the Exposure, shifting the point you click to white (1.0 for HDR images).
    The Midtone eyedropper sets the Exposure, making the value you click middle gray.
    === === ===
    Apply the Brightness/Contrast adjustment
    Comments (0)
    The Brightness/Contrast adjustment lets you make simple adjustments to the tonal range of an image. Moving the brightness slider to the right increases tonal values and expands image highlights, to the left decreases values and expands shadows. The contrast slider expands or shrinks the overall range of tonal values in the image.
    In normal mode, Brightness/Contrast applies proportionate (nonlinear) adjustments to image layer, as with Levels and Curves adjustments. When Use Legacy is selected, Brightness/Contrast simply shifts all pixel values higher or lower when adjusting brightness. Since this can cause clipping or loss of image detail in highlight or shadow areas, using Brightness/Contrast in Legacy mode is not recommended for photographic images (but can be useful for editing masks or scientific imagery).
    Note: Use Legacy is automatically selected when editing Brightness/Contrast adjustment layers created with previous versions of Photoshop.
    1. Do one of the following:
    Click the Brightness/Contrast icon in the Adjustments panel.
    Choose Layer > New Adjustment Layer > Brightness/Contrast. Click OK in the New Layer dialog box.
    Note: You can also choose Image > Adjustments > Brightness/Contrast. But keep in mind that this method makes direct adjustments to the image layer and discards image information.
    2. In the Adjustments panel, drag the sliders to adjust the brightness and contrast.
    Dragging to the left decreases the level, and dragging to the right increases it. The number at the right of each slider reflects the brightness or contrast value. Values can range from ‑150 to +150 for Brightness, ‑50 to +100 for Contrast.

Maybe you are looking for