Express not showing up..What worked for me...

After my 1st generation Express died last week, I got the new 802.11n-enabled unit. I was able to use Airport Utility to set the device up initially, but after rebooting the unit, it disappeared from my network, a WPA protected WDS-type with one Extreme b/g unit acting as the main unit, never to reappear. Numerous resets appeared to be fruitless, even the hardware reset where you hold the reset button down as you plug in the unit did not work.
After reading a bunch of posts on here, I finally got my unit to work. Here's what I did.
First, I did a "hard"-reset on the Express by holding down the reset button till the light started to flash amber, then releasing it. After about 30 seconds of solid amber, the express showed up in Airport utility. I copied its Airport ID number shown. Next I got the same information for the Extreme base station, which by the way, always showed up in AU.
I opened up the config window for the Extreme base station, by double clicking on its icon in Airport Utility. I then verified that it was set to be part of a WDS, confirmed passwords, etc and then manually added the Express's Airport ID # in the box for remotes. Clicked the update button and let it do its thing...
Now here's the trick... Power down your airport card, and plug the Express into your computer with an ethernet cable. At this time the Express is probably blinking amber slowly. Wait a few seconds, and then look for the Express in Airport Utility, (you may have to restart Utility, or at least hit the rescan button). My Express was now available for configuration. I followed the procedure as outlined above for the Extreme base station, although this time when prompted I entered in the Airport ID# for the Extreme base station, and set the Express to act as a remote in the WDS window. Enter security options and passwords to match the network you have entered, and hit the update button.
After a seemingly long restart, the Express showed up in the Utility, with a green light no less! I disconnected the ethernet cable, turned on my wireless card, selected the network and voila! it works. Checking AU showed both units as expected, with each one now fully updatable from their respective configuration windows.
So in summary, it appears that the newer Express units that are running 7.3.1 firmware, or those that have been updated to this firmware, have a bug that doesn't allow wireless configuration from an initial state. The 1st configuration needs a direct ethernet connection to "take". In addition, it seems Apple's instructions on doing a hardware reset (the one that resets unit to factory defaults by plugging in the unit while holding the reset button) does not work with the n-enabled boxes. This method did work for the b/g units however. There is a "soft"-reset (hold the reset button in for a second or two which pretty much is the same as un-plugging and re-plugging the unit) and the "hard"-reset, which I outlined above.
I apologize if this is a long winded post, but I hope that I may have been able to help some people out who appear to have been having the same problem that I had.
Good luck!!

Yes, the same thing has happened to me. My internet connection was working fine, but I couldn't see my Airport Express in the Admin Utility nor could I see my remote AirTunes speakers in iTunes. After a restart, everything came back to normal. So if anyone else is facing something similar, try that before panicking.
iMac G5, iBook G3 Mac OS X (10.4.5)

Similar Messages

When I connect my ipod to 2 different Mac computers, it will charge but is not showing up in itunes for sync. What happened?

When I connect my ipod to 2 different Mac computers, it will charge but is not showing up in itunes for sync. What happened?

What have you tried so far in terms of troubleshooting this issue? Are you plugging the iPod into a high powered USB 2.0 port on the back of your Mac? Have you tried a different USB cable?
What happens if you try to reset the device with it still connected to the Mac?
How to reset iPod
Has this iPod ever worked on this Mac or is this the first time you have time you have tried connecting it?
Have you carefully worked through each and every single suggestion in this Apple support document?
iPod not recognized in iTunes and Mac desktop
B-rock

HT2534 Tried to set up my Apple ID and the none button option for Billing is not showing up, what can I do?

Tried to set up my Apple ID and the none button option for Billing is not showing up, what can I do?

Try this support page provided by Apple...
http://support.apple.com/kb/ht2534

Trying to reconnect airport express to time machine but express not showing up in base station. unfortunately clicked forgot in airport utility and express no longer shows up. how to reconnect?

trying to reconnect airport express to time machine but express not showing up in base station. unfortunately clicked forgot in airport utility and express no longer shows up. how to reconnect?

I would recommend setting the wireless encryption on the AirPort Express BEFORE configuring it for the AirPort Extreme in this case. This issue also comes up often when configuring AirPorts into a WDS.
If setting up security in my recommend order does not work, temporarily connect the Express by Ethernet to the Extreme; make the security changes, and then, move the Express back to the desired location.

QT7 installing(what worked for me)

There have been numerous post's about having problems installing QT7. I had the same problem and got the same errors that other's are posting. There doesn't seem to be a accurate solution to this problem of wether it is the Microsoft OS or the Apple installer. So I will post what worked for me in finally getting QT7 standalone to install.
I downloaded SP2 for XP pro to get Windows Installer 3.1, I previously had version 2.0
I then removed QT from the computer using the add/remove control panel. And then went to the Folder Options control panel and selected, show hidden files and folders. Then went to Start>search all files and folders, QuickTime, and removed all that was left behind.
I then went into the registry, Start>run>type in regedit>OK
In the registry, I first went to HKEYLOCALMACHINE+SOFTWARE and deleted Apple Computer, Inc. And then hit the F3 key on the keyboard to get the next QT registry key to appear delete it and hit the F3 again for the next one to appear, and keep repeating this until they are all removed.
I then went to each registry listing-HKEYCLASSESROOT, HKEYCURRENTUSER, HKEY_USERS, HKEYCURRENTCONFIG
And would click on one to highlight and then go to the Edit menu, click find, type in QuickTime, hit the enter key on the keyboard. Delete the QT registry entry, and hit the F3 keyboard key for the next one to appear. I went thru this procedure until everything QT was removed from the computer.
Note: the registry is very risky to go into deleting keys. It would be wise to go to the microsoft website to get further info before attempting anything in it!
This worked for me. QT7 standalone then installed. I also downloaded Windows Installer Clean up Utility. Ran it and found QT 7.02 in there and removed it.
goodluck

I don't know why this is not installing on some computers and not others. It took me 2 or 3 days to get it to.
The only things I did was update to SP2 to get Windows Installer 3.1 Remove everything QT from the computer as I previously mentioned.
In Install Shield I downloaded driver 7. I had read a article about having the same number driver in Install Shield as the first number of the version of the progarm you are trying to install. In this case it is 7.0.2, so I downloaded 7. I did not bookmark the link to this. So I don't know now where it is on the web. But after doing this it still did not install.
It didn't install to after I removed QT from the computer and ran Windows Installer Cleanup Utility. And removed QT which was in there. Here is the link to download the installer cleanup utility.
http://support.microsoft.com/default.aspx?scid=kb;en-us;290301
Also this link my be of interest.
http://consumer.installshield.com/kb.asp?id=Q108393
I don't know what it was exactly that got it to install. But this is all I did. If you have any other questions or compare what I have on this computer your welcome to ask.
I realize it is fustrating and wish I could have been of more help.

Here's what worked for me...

Here's what worked for me:
1) I opened iTunes and in Options, I selected iTunes as the default music player for my computer (it wasn't). (I even uninstalled RealPlayer and WinAmp.)
2) I uninstalled iTunes and iPod, and reinstalled using the newer versions on the Apple site.
3) I basically followed this advice:
http://discussions.apple.com/thread.jspa?threadID=291183&tstart=0
Which was basically to leave my iPod connected to the computer while rebooting. The first 2 times it didn't work, I forgot to put iTunes in the start menu, so that it opens when I reboot. I put iTunes and iTunes Helper (whatever that is) in the start menu (I used WinPatrol to do so, available for free here: http://www.winpatrol.com/), and then rebooted, and after a couple of tries, like magic iTunes opened, recognized my iPod, and updated it, and then, for the first time, without freezing my system, told me it was okay to disconnect.
It even worked while still running my regular systray apps, like McAfee VirusScan, Ewido Anti-Malware, Microsoft AntiSpyware Beta, and SpywareBlaster, so those were not the issue. I get the impression you need to boot it once so it recognizes the iPod and does that handshake thing, and hopefully after that it'll always do the same. We'll see...
I hope this helps someone, b/c its been a frustrating day working through all this, and I know a lot of others are still trying to get it solved. And thanks to jcog for posting his solution, that helped me, and hopefully this will help someone else...
c.
iPod Video, 60GB Windows XP

it worked until the next time I synced the iPod, and then back to the freeze up. Next thing I tried was this Microsoft help page:
http://docs.info.apple.com/article.html?artnum=93976
which advises on several things, all of which seem helpful, but the thing still freezes up. I can sync the iPod, then the system freezes and I have to reboot. So, I now believe Apple will have to issue a patch for these bugs when using the new 5G iPods with WinXP.
c.
iPod Video, 60GB Windows XP

Snow Leopard Printing Woes - what worked for me

I found many print problems posted EVERYWHERE from every printer manufacturer and model and many solutions and some worked for some people. None worked for me.
I have a HP Laserjet 2100M, which is old, but is listed as compatible with SL. I cannot part with it, as it is a true laser printer, not a monochrome, which means when I need to colour separate say a blue and red document, it prints as solid, not grayscale. It has printed 44,820 pages for me over the years, with only laser cartridge replacement as an expense. As well, I cannot find anything but monochrome for a replacement.
It worked on my old iMac G5 running Leopard, however, when I got my new iMac running Snow Leopard, I got "Printer Offline" message and it would not go online and while some solution ideas got it to print, sometimes, it was only good for one or two jobs and then would stop again, or it would say printing and nothing would print.
Here is what worked for me:
I disconnected my printer's usb and power supply, reset printer system.
Went to Macintosh HD-Library-printers-PPDs-contents-resources and deleted all of the HP Drivers.
I got my HP 2100 series driver from my old iMac and put that back in the resources folder and emptied trash.
I shut down my computer.
Replugged in power to printer.
Started up computer.
After fully launched, I connected my USB cable for the printer. I went to add printer and it came up right away and said new software update was available for my printer AND I SAID NO to updating. In selected my driver, and...
My printer and I have reached a compromise!
It still says offline, however, everything is printing anyway... this I can live with.
I also found this link, which I will only try if I encounter any other disruptions
http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?lang=en&cc=us&task Id=110&prodSeriesId=385457&prodTypeId=18972&prodSeriesId=385457&objectID=c018677 22
At some point I printed a Self Test/Configuration page which has I/O Port Status as
USB STATUS - not ready
and Appletalk Status - Ready
which is probably a good clue, however, I have been printing successfully for 15 hours and my hair is starting to grow back.

The HP document appears to solve your issue. When your hair starts falling out again, use it.

Vendor Ref No. does not show in Journal Entry for AP Credit

AP Invoice journals show the vendor reference number in field Ref 2. However, when creating an AP Credit memo, the vendor reference number does not show in the journal for the credit memo, instead the field Ref 2 is used for the base document number.
I have two clients who have pointed out that they would expect to see the vendor ref number in the Ref 2 field in the journal when an AP Credit is created, as this is the functionality for Goods Receipts and AP Invoices.
Both clients are currently manually updating the Ref 2 field in the journal for AP Credit, so that in the BP account transactions view they can sort field Ref2 by vendor reference number.
Does anyone have any suggestions on a work around for this?
Thanks,
Lianne Plant

Hi Lianne Plant,
You may check: Journal Ref2 field : AP credit note
Thanks,
Gordon

IPhone-Outlook 2007 Calendar Sync (What worked for me)

Hi;
Today after 3 weeks of day after day trial my iPhone-Outlook 2007 Calenar synch problems seems to be fully fixed. Once again this is what worked for me - I am sharing it and hope that can help you as well:
Overview
========================
I now fully believe that the root cause of the issue starts from a corrupted appoinment entry in your local calendar file. This appointment entry in turn breaks your outlook sync file known as the .OST file. I will tell you how to fix this later. This file is what iTune uses to synch the iPHONE calendar with your Outlook 2007 (same should work for outlook 2003).
In short when the outlooksync.DLL file called by iTUNE, request to sync with outlook - it is the outlook that cannot resolve a corrupt .OST file and all goes to **** after that.
I say this as "This is up to you find this bad calendar entry, get rid of it, get rid of the .OST file, and finally tell Outlook to do a repair job on your outlook installation. I will tell you all how to do this as well.
Steps to fix this issue:
===========================================
1- Go to your outlook calendar and delete any old appointment that still is in there. I got rid of anything older that 2 weeks. To do this just go to your calendar in outlook ... swith to a List view ... sort based on date and highlight anything older than that date and delete. This took me about 30-45 miutes of work... so be paitent with this step. Also, get rid of any holiday notification BS that Outlook puts in your calendar ... you can do this later.
2- Go to outlook-tools-trust center-click on Add-In and then at the bottom of the screen click on Go and validate that your two outlook sync dlls are marked and enabled.
3- Shut down outook and go to the following directory.
C:\Documents and Settings\user name\Local Settings\
Application Data\Microsoft\Outlook
and rename your .OST file ... (there should be only one out there).
3- Go to your control panel and do start/stop applications. Select Outlook and click on change ... outlook will come up with a few options. Select "Repair" this should force outlook to replace the .OST file which you just renamed.
4- Now starts your outlook and let it do its initial sync. Make sure iTune is off at this point. After the Outlooks initialization is done ... now comes the moment of truth...
5- Start iTune (I recommend that you select manual sync) and sycn with your calendar.
At this point I learned that all my calendar items have come in ....
Good luck and let me know if this works with you. Please Please remember the first step ... getting rid of your old appointments is the most important step ... don't rush it ... get rid of anything that you don't need.
Cheers;
Darab.

You can try resetting sync history by clicking on edit at the top of itunes and choosing preferences. Then click on the iphone icon at the right top of the window that opens. There is a button at the bottom of the window to reset sync history.
Also, you can try creating a new login on the computer.
Open outlook and put in a few trial events.
Then sync the iphone to this outlook calendar replacing all calendar data on the iphone.
This is to see if you end up with dots on every day.
If you do not end up with dots on every day, then you might want to take a look at any reoccurring events in the other outlook calendar.
Hope this helps.

HT1727 help how do i make a purchased song my ring tone, it;s not showing on my list for ringtones

help how do i make a purchased song my ring tone, it's not showing on my list for ringtones

This song was purchased from the iTunes Store?
If so, you can't create a ringtone from music that was purchased from the iTunes store, but if there is a ringtone available for purchase and download at the iTunes Store with this song, you need to do that.
For music in your iTunes library on your computer that was not purchased from the iTunes store, there are a number of ways to create a ringtone with such music. With a Mac, there is an inexpensive or free app avaiable via Apple's online App Store named Ringer. Ringer has access to all music and sound files in your iTunes library that was not downloaded from the iTunes Store for creating your chosen segment of the song to be used for the ringtone. The app places the created ringtone in your iTunes library under Tones for transfer to your iPhone when syncing.
Creating ringtones on a Mac can also be done with GarageBand, and there is a manual way of doing this with iTunes.

THIS IS WHAT WORKED FOR ME

For hours I tried clicking back and forth from something else in iTunes back to the "iPhone" hoping to reconnect; that didn't work it! After five hours of clicking back and forth (as other users suggested) I decided to browse the iTunes store and after I looked at everything "AS SOON" as I clicked "iPhone" it began to restore the back-up. So I guess Apple wants to see if you are interested in spending all your money with their enticing iPhone enhancement apps that should have came with the original iPhones in the first place before they let you finish your upgrade. Hope this works.
[Serious Post]

This is what worked for me:
I called 1-877-419-4500. I got a guy named Don.
I asked him to make sure the 'business' thing wasn't on my account. It wasn't.
We reset the phone. (Hold home button and sleep/wake button) nothing.
He said he was going to get a hold of someone in the 'technical activation dept'. He did.
They found a 'glitch' on my account. Seems the activation was placed on hold. they took that off.
turned off my phone, plugged it into usb cable, itunes got it, viola! activated.
call that number. talk directly to a human, no wait, no menus.

My Apple TV and IPad drop after x mintues from "Home Sharing". To restart it, I need to close iTunes on my Windows 7 PC, open it , then I can listen again X minutes (15-90 minutes) to my music via "Home Sharing". Any idea why? What worked for you?

My Apple TV and IPad drop after x mintues from "Home Sharing". To restart it, I need to close iTunes on my Windows 7 PC, open it , then I can listen again X minutes (15-90 minutes) to my music via "Home Sharing". Any idea why? What worked for you?

I believe if you updated your Apple TV, you need iTunes 11 to make it work.

Airport Express not showing name given

Hello Community,
I have the latest Airport Extreme and Airport Express. I am also using the latest Airport Utility, 6.0.
I am using the Airport Express to extend my network. However, under my Wi-Fi icon (upper right icon), I can not see the name given to my Airport Express. Therefore I can not manually select it. I can see it's name in iTunes, if I want to remotely play music and under "Network>Advanced" I can see it has the "same" name as my Extreme, but with an "AE" after the Extreme's name. Im sure that means Airport Express. Also, of course I can see the AE and the name given to it using Airport Utility.
Question, why is the name given to the Airport Express not showing up under my Wi-Fi ? I could have sworn when I first configured it, it showed up under the Wi-Fi drop down menu under "Other Devices", I believe it read.
I am running Lion, 10.7.3
Any help please ? Thank you in advance !

By the way, I set up the Airport Express wirelessly. Should I have connected it with an Ethernet to my Extreme to set the Express as an Extended network device ? Thanks !

This is what worked for me, Read!!!! Now I am activated

So like many of you I was stuck waiting for 24 hours. To make this short, do this. If you have been emailed and Activation ID call...877-800-3701. Ask them to cancel the current attempt to activate. Once you do, then connect and iTunes will prompt you to activate as if nothing ever happened. Once I did I was done in five minutes. My hunch is that "We", that are waiting for countless hours, we are stuck in some sort of loop. Break it and good luck.
Vlonjati

This is what worked for me:
I called 1-877-419-4500. I got a guy named Don.
I asked him to make sure the 'business' thing wasn't on my account. It wasn't.
We reset the phone. (Hold home button and sleep/wake button) nothing.
He said he was going to get a hold of someone in the 'technical activation dept'. He did.
They found a 'glitch' on my account. Seems the activation was placed on hold. they took that off.
turned off my phone, plugged it into usb cable, itunes got it, viola! activated.
call that number. talk directly to a human, no wait, no menus.

AirPort Express Not Showing as Option for Playback

I have an AirPort Express (new with latest firmware) connected to my Wireless LAN (802.11g). Both of my computers can see it (that is, I can access it from the configuration utility), however, when I load iTunes it will not show as a playback option (pulldown on bottom of iTunes screen) on one computer, unless I first ping the IP of the AirPort. Sometimes this works, sometimes not. Note that iTunes is not loaded on the other computer at the time and I do not have a firewall between the computers on the LAN. I am using WEP encryption, but I've entered the key successfully on both computers and on the AirPort. I've also opened the specified port (5353?) on my router, although that shouldn't matter, as I'm not trying to route outside my LAN.
As mentioned I have latest AirPort firmware and iTunes upgrades loaded on both Windows XP computers, as well as SP2.
Ideas or suggestions?
Various - Mac & Windows XP Windows XP Pro Windows XP can't find AirPort
Various - Mac & Windows XP Windows XP Pro

i assume your airport extreme base station (AEBS) is you main router and you want the airport express (AX) join the network provided by the AEBS.
you could try this:
unplug and re-plug the airport express (AX), then click on the airport icon in your menu bar. you should see something like "Apple network bj1234567" or similar (it may take a little while for it to show up). in order to set up the express, you will have to temporarily join its network ! you will get a message asking +do you really want to switch networks ?+ and you do want to do that.
launch airport utility (AU). you should see the AX on the left. click on the icon of the AX once to highlight it and click continue. follow onscreen instructions and, when prompted, choose to +join an existing network+ and enter the required information for your network.
any help ?

Express not showing up..What worked for me...

Similar Messages

Maybe you are looking for