Express sub card not working

I upgraded my E520 to windows 7 Pro from Windows Xp after a hard drive crash. I was able to get everything to work but the 34 pin Express sub card slot. I am not sure if I am missing a driver or what. Any suggestions?

The closest driver I can think of is the Intel chipset driver.
Try installing that with the -overall switch:
https://www.raymond.cc/blog/the-proper-way-to-fully-install-intel-chipset-driver/
W520: i7-2720QM, Q2000M at 1080/688/1376, 21GB RAM, 500GB + 750GB HDD, FHD screen
X61T: L7500, 3GB RAM, 500GB HDD, XGA screen, Ultrabase
Y3P: 5Y70, 8GB RAM, 256GB SSD, QHD+ screen

Similar Messages

Sound Blaster X-FI Pci Express Front Panel Not working right Win7

ASound Blaster X-FI Pci Express Front Panel Not working right Win7
Please read carefully
Part number Part SB040
Hello,
I have a fresh install of Win7x64 OEM. First, I want to say that I have "AUTOMATICALLY MUTE SPEAKERS" UNCHECKED under the Headphone detection tab. I have tried "Automatically Enable Headphone Settings" checked or unchecked. No difference.
As soon as I plug in headphones to the front panel connector , the speakers in the mixer say "disconnected" (see below) and the SPDIF becomes the default output. There is no way for me to change this. And there isn't any sound coming from the headphones when plugged into the front panel. (the mic front panel works fine)
I am using the nati've Win7 drivers for the card. Apparently the Win 7 drivers on your site are older than the nati've ones.
This worked fine in Windows XP 32. Any ideas.

Ok guys this is how I fixed the problem on my X-Fi PCI-Express. Open the Creative SB X-Fi Volume panel. Mine is set in game mode and I have 5 vertical sliders for Line-In /Mic, MIDI Synth, Digital-In, and the last one will say one of three things either Digital-In, Microphone, or Mirophone FP. At the top of the?slider there is a tab which brings up a drop down menu. Mine was default set to Digital-In, I switched it to Mirophone FP (tried Microphone first and it worked but the FP sounds better for me) and cranked it all the way up and my problem was solved. Very frustrating one though as there is no documentation that led me to the fix it was just playing around with it till I could figure it out.
I hope this at least helps some of you out.

Runtime error R6025 message after log on to Vista - Flash Card not working

Hi
I'm a newbie & would appreciate any advice.
I am getting a runtime error message R6025 when I log on to Windows Vista.
When I click out of the box I then get a message saying Toshiba Flash Card not working.
I cancel that and my laptop is ok except I don't know if the flashcard is working or not because I don't know what it does.
Sorry if I sound thick
Thanks
Neelie

Hi
I found this MS knowledge base article:
+Description of the R6025 run-time error in Visual C++\+
http://support.microsoft.com/kb/125749
But I doubt this description would be useful for you or anyone here. It describes this error in Visual C++ and this is programming language.
However, I think you should simply reinstall the Value Added Package which you could download firstly from the Toshiba European page.
At first you have to remove the old Value Added Package from the system, then reboot the notebook and follow with new VAP installation.
Bye

I have installed the agent 10 or 15 times and one installation hasfailed, no error appeared during the installation but I am havinginconsistent issues with my ethernet card not working here and there. Werebooted and can log into Novell client but th

I have installed the agent 10 or 15 times and one installation has failed, no error appeared during the installation but I am having inconsistent issues with my ethernet card not working here and there. We rebooted and can log into Novell client but the login prompt did not appear for ESM client or the icon was not in the systray. Everything seems to work, besides at times (a couple times today) it terminates his ethernet card/connection. I would re-image his computer but he has several applications and it would take several hours, so I am hoping someone has an idea to fix this issue. So I was trying to figure out why he did not get the prompt to login and why it's not in the systray and it appears to not have completed the install? I checked the add/remove programs, its not listed within their, I also checked the registry and found nothing for endpoint within their, but the files are within c:\program files\novell\zenworks endpoint security.
I have also tried uninstalling it but that fails due to it "not being installed", and it will not reinstall over itself either.
I did notice that stuninstdrv.exe is running in task manager. Any help would be great...
Windows xp sp3
ESM 3.5.154
Thanks,
Andy

If you are searching the registry, check for the "Senforce" string. It should be at HKLM\Software\Senforce
Try running the install program for the ZSC with the following command line:
setup.exe /V"STUNINSTALL=1"
If you've specified an uninstall password, try this one instead:
setup.exe /V"STUNINSTALL=1 STUIP=password"" (please note the double quote at the end)
Let me know if that helped you.
Daniel
>>>
From: Andy_DeWees<[email protected] du>
To:novell.support.zenworks.endpoint-security-management
Date: 2/5/2009 12:52 PM
Subject: I have installed the agent 10 or 15 times and one installation hasfailed, no error appeared during the installation but I am havinginconsistent issues with my ethernet card not working here and there. Werebooted and can log into Novell client but the login prompt did not appearfor ESM client or the icon was not in the systray. Everything seems towork, besides at times (a couple times today) it terminates his ethernetcard/connection. I would re-image his computer but he has severalapplications and
I have installed the agent 10 or 15 times and one installation has failed, no error appeared during the installation but I am having inconsistent issues with my ethernet card not working here and there. We rebooted and can log into Novell client but the login prompt did not appear for ESM client or the icon was not in the systray. Everything seems to work, besides at times (a couple times today) it terminates his ethernet card/connection. I would re-image his computer but he has several applications and it would take several hours, so I am hoping someone has an idea to fix this issue. So I was trying to figure out why he did not get the prompt to login and why it's not in the systray and it appears to not have completed the install? I checked the add/remove programs, its not listed within their, I also checked the registry and found nothing for endpoint within their, but the files are within c:\program files\novell\zenworks endpoint security.
I have also tried uninstalling it but that fails due to it "not being installed", and it will not reinstall over itself either.
I did notice that stuninstdrv.exe is running in task manager. Any help would be great...
Windows xp sp3
ESM 3.5.154
Thanks,
Andy

SB04100 Sound Blaster Card not working after computer rebuild

=SB0400 Sound Blaster Card not working after computer rebuildZ I did a full disk format and reinstall for a friend on a Dimension 3000, running XP SP3. There is no sound at all. Speakers are good, tested on another system. Model number on the back of the sound card is SB0400, so I assume this is an older 24 bit PCI SoundBlaster card. Although I reinstalled all drivers from Dell, I found no drivers for this. The Creative site has no listing for this model.
Computer does not seem to recognize the card. Have not opened the box yet but I assume if I were to remove and then reinstall the card it would be recognized (?) I then have to find an SB0400 driver.
Does anyone know where I can find an SB0400 driver ? Does the strategy of pulling and reinstalling the card make sense ? (I have really avoided tampering with any of the hardware on this box -- since it is not mine.)

Re: SB0400 Sound Blaster Card not working after computer rebuild? Thanks much for your response. Problem solved for now. I removed the board and then reinserted it, after which I was able to download the drivers directly. Some of my difficulty with this whole process has been ) I didn't know there was no working speaker in the computer and 2) I apparently misunderstood the BIOS settings for this. I re-set it up as an add-on board during the troubleshooting process. After loading the driver, I went back to the original setting (don't recall what it was but it was for integrated sound). The setting for integrated sound works fine, with external speakers and the new 24 bit driver. Still some noise (popping and static) but this board shares the bus with 2 other cards one of which is a wireless network card. May be a PCI latency issue but I'm reluctant to change that because the network card is a bit shaky anyway.
Everything works for now -- I'll be glad to get this particular computer out of my house !

TS4317 graphics cards not work

video file is not working graphics card not working is their is any software that i can update. or tell me why its not working

If you can see an image on your screen then your graphics card (Intel HD Graphics 3000) integrated into your 13" machine is working just fine.
I'm not sure what you mean when you say that a video file isn't working... how exactly isn't it 'working' and what file format is it in?
Clinton

TS1292 iTunes card not working

iTunes $15?card not working. AppleID shows a $15 balance, but none of my purchases are going through

krek alvarez wrote:
...say is contact to costumer support
Use this Link > Apple Support iTunes Store Contact

HELP! - Lumia 800 memory card not working :/

My phone decided to go into the notorious restart loop - So following everyones advice on teh internet I performed a hard reset.
It loads the orange sign - then the Nokia sign - then the windows mobile sign as if the phone is about to start with the noises etc... then it decides to goto a screen says
"MEMORY CARD NOT WORKING
Your memory card has changed, is damaged or is non-compatible.
To fix this, turn your phone off and either remove the memory card or replace it with a new compatible card. Then reset your phone to the original factory settings.
To learn how to reset your phone, refer to the owner's manual"
I also get the option to make an "emergency" call or "turn off" the phone. the volume buttons also work the volume fine aswell as the option to change the phones mode from silent to vibrate or vibrate and ring.
Tried hard reset numerous times, tried charing the phone for hours on end and trying it, tried soft resets. Basically the only options i've found.
Just to add.... Why would a phone with no memory card slot even have a message stating that the memory card is faulty and that i could even remove or replace it???
I hope someone manages to help me without having to cough up £50 excess to my insurance.
Anyone come across this before?

Sorry, it's my standard response, but your phone doesn't work. Take it back to whoever sold it to you. It's a consumer good, consumer protection rules apply.
Your problem certainly has novelty value but if you've done the hard reset and it didn't work you're at the end of the fix it yourself stage.

I can buy my needs from the game says I tell customers to help please help me Visa card not working in any Itemes games

I can buy my needs from the game says I tell customers to help please help me Visa card not working in any Itemes
games

If you mean that you have been instructed to contact iTunes support, then will need to do what it says, contact iTunes Support. These are user-to-user support forums, if you thought you were contacting Apple by posting here. Go here:
http://www.apple.com/emea/support/itunes/contact.html
to contact the iTunes Store.
If that does not answer your question, try posting in your native language, or find a friend with a better command of English to help you ask your question here.
Regards.

USB/eSata express card not working on stock kernel

Hello everyone,
I have a weird problem and I don't seem to find any solution by myself. Let me give you some background info on what I plan to do.
I purchased an express card to eSata/USB 3.0 adapter and want to make it work on my laptops. Precisely, it is this card: http://www.amazon.de/Notebook-Express-C … B007F8TXZ8
1: Lenovo X200s (1,6GHz) running Ubuntu 14.04 amd64
2: Lenovo X200s (1,6GHz) running Debian 7 amd64
3: Lenovo X200T (1,6GHz) running ArchLinux amd64
The card does work fine only on the Ubuntu machine. I would like to make it run on the two other ones as well. I thought I might get help here getting it to work on machine 3 and then transfer the results to machine 2. What really matters to me is eSata, btw, I do not even have a USB 3.0 device to test with.
First of all, here's what happens when I plug the card into machine 1:
user@1-ubuntu:~$ uname -r
3.13.0-39-generic
user@1-ubuntu:~$ dmesg | tail -n 44 # that's where it begins
[ 1953.576472] pciehp 0000:00:1c.3:pcie04: Card present on Slot(3)
[ 1953.728077] pci 0000:05:00.0: [1b21:1042] type 00 class 0x0c0330
[ 1953.728119] pci 0000:05:00.0: reg 0x10: [mem 0x00000000-0x00007fff 64bit]
[ 1953.728304] pci 0000:05:00.0: PME# supported from D3hot
[ 1953.736062] pci 0000:05:00.0: BAR 0: assigned [mem 0xf0000000-0xf0007fff 64bit]
[ 1953.736087] pcieport 0000:00:1c.3: PCI bridge to [bus 05-0c]
[ 1953.736092] pcieport 0000:00:1c.3: bridge window [io 0x2000-0x2fff]
[ 1953.736098] pcieport 0000:00:1c.3: bridge window [mem 0xf0000000-0xf1ffffff]
[ 1953.736104] pcieport 0000:00:1c.3: bridge window [mem 0xf2900000-0xf29fffff 64bit pref]
[ 1953.736133] pci 0000:05:00.0: no hotplug settings from platform
[ 1953.736143] pci 0000:05:00.0: enabling device (0000 -> 0002)
[ 1953.736398] xhci_hcd 0000:05:00.0: xHCI Host Controller
[ 1953.736406] xhci_hcd 0000:05:00.0: new USB bus registered, assigned bus number 9
[ 1953.743621] xhci_hcd 0000:05:00.0: irq 46 for MSI/MSI-X
[ 1953.743629] xhci_hcd 0000:05:00.0: irq 49 for MSI/MSI-X
[ 1953.743635] xhci_hcd 0000:05:00.0: irq 50 for MSI/MSI-X
[ 1953.743784] usb usb9: New USB device found, idVendor=1d6b, idProduct=0002
[ 1953.743788] usb usb9: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1953.743791] usb usb9: Product: xHCI Host Controller
[ 1953.743794] usb usb9: Manufacturer: Linux 3.13.0-39-generic xhci_hcd
[ 1953.743796] usb usb9: SerialNumber: 0000:05:00.0
[ 1953.743973] hub 9-0:1.0: USB hub found
[ 1953.743990] hub 9-0:1.0: 2 ports detected
[ 1953.744147] xhci_hcd 0000:05:00.0: xHCI Host Controller
[ 1953.744153] xhci_hcd 0000:05:00.0: new USB bus registered, assigned bus number 10
[ 1953.744218] usb usb10: New USB device found, idVendor=1d6b, idProduct=0003
[ 1953.744221] usb usb10: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1953.744224] usb usb10: Product: xHCI Host Controller
[ 1953.744227] usb usb10: Manufacturer: Linux 3.13.0-39-generic xhci_hcd
[ 1953.744229] usb usb10: SerialNumber: 0000:05:00.0
[ 1953.744366] hub 10-0:1.0: USB hub found
[ 1953.744383] hub 10-0:1.0: 2 ports detected
[ 1954.447851] usb 10-1: new SuperSpeed USB device number 2 using xhci_hcd
[ 1954.460505] usb 10-1: Parent hub missing LPM exit latency info. Power management will be impacted.
[ 1954.461215] usb 10-1: New USB device found, idVendor=174c, idProduct=5106
[ 1954.461219] usb 10-1: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[ 1954.461222] usb 10-1: Product: AS2105
[ 1954.461225] usb 10-1: Manufacturer: ASMedia
[ 1954.461228] usb 10-1: SerialNumber: 00000000000000000000
[ 1954.463146] usb-storage 10-1:1.0: USB Mass Storage device detected
[ 1954.463279] scsi7 : usb-storage 10-1:1.0
[ 1955.460385] scsi 7:0:0:0: Direct-Access ASMT 2105 0 PQ: 0 ANSI: 5
[ 1955.465099] sd 7:0:0:0: Attached scsi generic sg1 type 0
[ 1955.466483] sd 7:0:0:0: [sdb] Attached SCSI removable disk
I wouldn't know of any attached disks, and neither does it show up. Note that it is only the card I plugged in, no hard drive attached to it.
hburg1234@packrehsel:~$ lspci -k
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07)
Subsystem: Lenovo Device 20e0
Kernel driver in use: agpgart-intel
00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07)
Subsystem: Lenovo Device 20e4
Kernel driver in use: i915
00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07)
Subsystem: Lenovo Device 20e4
00:03.0 Communication controller: Intel Corporation Mobile 4 Series Chipset MEI Controller (rev 07)
Subsystem: Lenovo Device 20e6
Kernel driver in use: mei_me
00:03.3 Serial controller: Intel Corporation Mobile 4 Series Chipset AMT SOL Redirection (rev 07)
Subsystem: Lenovo Device 20ec
Kernel driver in use: serial
00:19.0 Ethernet controller: Intel Corporation 82567LM Gigabit Network Connection (rev 03)
Subsystem: Lenovo Device 20ee
Kernel driver in use: e1000e
00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03)
Subsystem: Lenovo Device 20f0
Kernel driver in use: uhci_hcd
00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03)
Subsystem: Lenovo Device 20f0
Kernel driver in use: uhci_hcd
00:1a.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03)
Subsystem: Lenovo Device 20f0
Kernel driver in use: uhci_hcd
00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03)
Subsystem: Lenovo Device 20f1
Kernel driver in use: ehci-pci
00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03)
Subsystem: Lenovo Device 20f2
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03)
Kernel driver in use: pcieport
00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 03)
Kernel driver in use: pcieport
00:1c.3 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 (rev 03)
Kernel driver in use: pcieport
00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03)
Subsystem: Lenovo Device 20f0
Kernel driver in use: uhci_hcd
00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03)
Subsystem: Lenovo Device 20f0
Kernel driver in use: uhci_hcd
00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03)
Subsystem: Lenovo Device 20f0
Kernel driver in use: uhci_hcd
00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03)
Subsystem: Lenovo Device 20f1
Kernel driver in use: ehci-pci
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93)
00:1f.0 ISA bridge: Intel Corporation ICH9M-E LPC Interface Controller (rev 03)
Subsystem: Lenovo Device 20f5
Kernel driver in use: lpc_ich
00:1f.2 SATA controller: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 4 port SATA Controller [AHCI mode] (rev 03)
Subsystem: Lenovo Device 20f8
Kernel driver in use: ahci
00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03)
Subsystem: Lenovo Device 20f9
03:00.0 Network controller: Intel Corporation PRO/Wireless 5100 AGN [Shiloh] Network Connection
Subsystem: Intel Corporation WiFi Link 5100 AGN
Kernel driver in use: iwlwifi
05:00.0 USB controller: ASMedia Technology Inc. ASM1042 SuperSpeed USB Host Controller
Subsystem: Device 174c:2104
Kernel driver in use: xhci_hcd
The last one seems to be important to me, so here's a verbose output on that one.
user@1-ubuntu:~$ lspci -v | tail -n 8
05:00.0 USB controller: ASMedia Technology Inc. ASM1042 SuperSpeed USB Host Controller (prog-if 30 [XHCI])
Subsystem: Device 174c:2104
Physical Slot: 3
Flags: bus master, fast devsel, latency 0, IRQ 19
Memory at f0000000 (64-bit, non-prefetchable) [size=32K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
user@1-ubuntu:~$ sudo udevadm monitor -k
monitor will print the received events for:
KERNEL - the kernel uevent
KERNEL[2585.956558] add /devices/pci0000:00/0000:00:1c.3/0000:05:00.0 (pci)
KERNEL[2585.972086] add /devices/pci0000:00/0000:00:1c.3/0000:05:00.0/usb9 (usb)
KERNEL[2585.972116] add /devices/pci0000:00/0000:00:1c.3/0000:05:00.0/usb9/9-0:1.0 (usb)
KERNEL[2585.975736] add /devices/pci0000:00/0000:00:1c.3/0000:05:00.0/usb10 (usb)
KERNEL[2585.975763] add /devices/pci0000:00/0000:00:1c.3/0000:05:00.0/usb10/10-0:1.0 (usb)
KERNEL[2586.689218] add /devices/pci0000:00/0000:00:1c.3/0000:05:00.0/usb10/10-1 (usb)
KERNEL[2586.690935] add /devices/pci0000:00/0000:00:1c.3/0000:05:00.0/usb10/10-1/10-1:1.0 (usb)
KERNEL[2586.695723] add /devices/pci0000:00/0000:00:1c.3/0000:05:00.0/usb10/10-1/10-1:1.0/host9 (scsi)
KERNEL[2586.695757] add /devices/pci0000:00/0000:00:1c.3/0000:05:00.0/usb10/10-1/10-1:1.0/host9/scsi_host/host9 (scsi_host)
KERNEL[2587.692633] add /devices/pci0000:00/0000:00:1c.3/0000:05:00.0/usb10/10-1/10-1:1.0/host9/target9:0:0 (scsi)
KERNEL[2587.692667] add /devices/pci0000:00/0000:00:1c.3/0000:05:00.0/usb10/10-1/10-1:1.0/host9/target9:0:0/9:0:0:0 (scsi)
KERNEL[2587.692691] add /devices/pci0000:00/0000:00:1c.3/0000:05:00.0/usb10/10-1/10-1:1.0/host9/target9:0:0/9:0:0:0/scsi_disk/9:0:0:0 (scsi_disk)
KERNEL[2587.692708] add /devices/pci0000:00/0000:00:1c.3/0000:05:00.0/usb10/10-1/10-1:1.0/host9/target9:0:0/9:0:0:0/scsi_device/9:0:0:0 (scsi_device)
KERNEL[2587.692824] add /devices/pci0000:00/0000:00:1c.3/0000:05:00.0/usb10/10-1/10-1:1.0/host9/target9:0:0/9:0:0:0/scsi_generic/sg1 (scsi_generic)
KERNEL[2587.692898] add /devices/pci0000:00/0000:00:1c.3/0000:05:00.0/usb10/10-1/10-1:1.0/host9/target9:0:0/9:0:0:0/bsg/9:0:0:0 (bsg)
KERNEL[2587.699636] add /devices/virtual/bdi/8:16 (bdi)
KERNEL[2587.699771] add /devices/pci0000:00/0000:00:1c.3/0000:05:00.0/usb10/10-1/10-1:1.0/host9/target9:0:0/9:0:0:0/block/sdb (block)
KERNEL[2587.703694] change /devices/pci0000:00/0000:00:1c.3/0000:05:00.0/usb10/10-1/10-1:1.0/host9/target9:0:0/9:0:0:0/block/sdb (block)
KERNEL[2587.709178] change /devices/pci0000:00/0000:00:1c.3/0000:05:00.0/usb10/10-1/10-1:1.0/host9/target9:0:0/9:0:0:0/block/sdb (block)
Apart from the supposedly found block device (can't judge) I am not sure if there is anything that is really eSata specific and not USB 3.0 related.
So far what I think I can tell from the output is that the modules
pciehp pci pcieport
seem to be dealing with the express card as such whereas
xhci_hcd
takes care of USB 3.0. I cannot see any clear reference to the eSata connector, which might not be surprising if the bus is just passed through (again: not sure).
For completeness' sake here comes the output of
user@1-ubuntu:~$ lsmod | tee before
Module Size Used by
ctr 13049 1
ccm 17773 1
pci_stub 12622 1
vboxpci 23194 0
vboxnetadp 25670 0
vboxnetflt 27613 0
vboxdrv 339502 3 vboxnetadp,vboxnetflt,vboxpci
cuse 13445 3
dm_crypt 23177 1
btusb 32412 0
cdc_ether 14351 0
usbnet 43913 1 cdc_ether
cdc_acm 28803 0
mii 13934 1 usbnet
cdc_wdm 19053 0
rfcomm 69160 8
bnep 19624 2
bluetooth 391136 22 bnep,btusb,rfcomm
binfmt_misc 17468 1
coretemp 13435 0
kvm_intel 143148 0
kvm 451729 1 kvm_intel
thinkpad_acpi 81013 0
nvram 14411 1 thinkpad_acpi
serio_raw 13462 0
arc4 12608 2
snd_seq_midi 13324 0
snd_seq_midi_event 14899 1 snd_seq_midi
snd_hda_codec_conexant 57441 1
iwldvm 232285 0
snd_hda_intel 56451 3
mac80211 630653 1 iwldvm
snd_hda_codec 192906 2 snd_hda_codec_conexant,snd_hda_intel
snd_hwdep 13602 1 snd_hda_codec
snd_rawmidi 30144 1 snd_seq_midi
lpc_ich 21080 0
iwlwifi 169932 1 iwldvm
snd_seq 61560 2 snd_seq_midi_event,snd_seq_midi
snd_pcm 102099 2 snd_hda_codec,snd_hda_intel
mei_me 18627 0
cfg80211 484040 3 iwlwifi,mac80211,iwldvm
snd_page_alloc 18710 2 snd_pcm,snd_hda_intel
mei 82276 1 mei_me
snd_seq_device 14497 3 snd_seq,snd_rawmidi,snd_seq_midi
snd_timer 29482 2 snd_pcm,snd_seq
snd 69322 17 snd_hwdep,snd_timer,snd_hda_codec_conexant,snd_pcm,snd_seq,snd_rawmidi,snd_hda_codec,snd_hda_intel,thinkpad_acpi,snd_seq_device,snd_seq_midi
soundcore 12680 1 snd
parport_pc 32701 0
ppdev 17671 0
mac_hid 13205 0
tp_smapi 28367 0
thinkpad_ec 14449 1 tp_smapi
lp 17759 0
parport 42348 3 lp,ppdev,parport_pc
i915 783961 2
psmouse 106714 0
ahci 25819 3
libahci 32716 1 ahci
i2c_algo_bit 13413 1 i915
e1000e 254433 0
drm_kms_helper 55071 1 i915
drm 303102 3 i915,drm_kms_helper
ptp 18933 1 e1000e
pps_core 19382 1 ptp
video 19476 1 i915
wmi 19177 0
and a list of the newly loaded modules:
user@1-ubuntu:~$ diff before <(lsmod)
1a2
> usb_storage 62209 0
Now, on my Arch machine the situation is as follows when the card is plugged in:
user@3-arch:~$ uname -r
3.17.2-1-ARCH
user@3-arch:~$ sudo udevadm monitor -k
monitor will print the received events for:
KERNEL - the kernel uevent
user@3-arch:~$ lsmod
Module Size Used by
sr_mod 21903 0
cdrom 47479 1 sr_mod
hid_generic 12393 0
usbhid 48603 0
hid 102220 2 hid_generic,usbhid
cdc_ether 12564 0
usbnet 34978 1 cdc_ether
cdc_acm 30362 0
cdc_wdm 17427 0
mii 12675 1 usbnet
ctr 12927 0
ccm 17534 0
fuse 87410 3
joydev 17063 0
wacom_w8001 12706 0
serport 12842 1
mousedev 17272 0
iTCO_wdt 12831 0
iTCO_vendor_support 12649 1 iTCO_wdt
coretemp 12820 0
kvm 417429 0
pcspkr 12595 0
psmouse 107214 0
evdev 21544 20
mac_hid 12633 0
serio_raw 12849 0
i2c_i801 16965 0
snd_hda_codec_conexant 21835 1
snd_hda_codec_generic 63126 1 snd_hda_codec_conexant
arc4 12536 2
iwldvm 184847 0
mac80211 604456 1 iwldvm
i915 905750 2
lpc_ich 20768 0
iwlwifi 156837 1 iwldvm
snd_hda_intel 26387 0
snd_hda_controller 26938 1 snd_hda_intel
cfg80211 445286 3 iwlwifi,mac80211,iwldvm
thinkpad_acpi 69074 0
e1000e 215686 0
snd_hda_codec 108536 4 snd_hda_codec_conexant,snd_hda_codec_generic,snd_hda_intel,snd_hda_controller
drm_kms_helper 80934 1 i915
shpchp 35210 0
snd_hwdep 17244 1 snd_hda_codec
snd_pcm 88487 3 snd_hda_codec,snd_hda_intel,snd_hda_controller
ptp 17692 1 e1000e
pps_core 17225 1 ptp
snd_timer 26614 1 snd_pcm
wmi 17339 0
drm 259106 4 i915,drm_kms_helper
nvram 13034 1 thinkpad_acpi
thermal 17559 0
snd 73436 8 snd_hwdep,snd_timer,snd_hda_codec_conexant,snd_pcm,snd_hda_codec_generic,snd_hda_codec,snd_hda_intel,thinkpad_acpi
soundcore 13031 2 snd,snd_hda_codec
led_class 12859 2 iwldvm,thinkpad_acpi
rfkill 18867 3 cfg80211,thinkpad_acpi
ac 12715 0
hwmon 12930 2 coretemp,thinkpad_acpi
acpi_cpufreq 17218 1
battery 17452 0
i2c_algo_bit 12744 1 i915
mei_me 17900 0
tpm_tis 17182 0
i2c_core 50152 5 drm,i915,i2c_i801,drm_kms_helper,i2c_algo_bit
tpm 31467 1 tpm_tis
mei 75079 1 mei_me
intel_agp 17432 0
intel_gtt 17848 3 i915,intel_agp
video 18043 1 i915
processor 27777 3 acpi_cpufreq
button 12953 1 i915
sch_fq_codel 17343 6
tp_smapi 27621 0
thinkpad_ec 12813 1 tp_smapi
ext4 497696 3
crc16 12343 1 ext4
mbcache 17171 1 ext4
jbd2 86417 1 ext4
sha256_ssse3 25692 2
sha256_generic 16804 1 sha256_ssse3
ecb 12737 0
cbc 12696 1
algif_skcipher 17051 0
af_alg 12988 1 algif_skcipher
dm_crypt 22551 1
dm_mod 93490 15 dm_crypt
sd_mod 44398 3
crct10dif_generic 12581 1
crc_t10dif 12431 1 sd_mod
crct10dif_common 12356 2 crct10dif_generic,crc_t10dif
atkbd 22254 0
libps2 12739 2 atkbd,psmouse
ata_generic 12490 0
ahci 33291 2
libahci 27158 1 ahci
pata_acpi 12771 0
uhci_hcd 43507 0
ehci_pci 12512 0
ehci_hcd 69939 1 ehci_pci
libata 181518 4 ahci,pata_acpi,libahci,ata_generic
usbcore 199381 9 uhci_hcd,ehci_hcd,ehci_pci,usbhid,usbnet,cdc_acm,cdc_wdm,cdc_ether
usb_common 12440 1 usbcore
scsi_mod 147543 3 libata,sd_mod,sr_mod
i8042 18002 1 libps2
serio 18282 9 serio_raw,atkbd,i8042,serport,wacom_w8001,psmouse
Sticking to my suspicion that this might just be a USB related issue and eSata might still work due to some sort of passthrough, I attached the very eSata drive that I could mount on Ubuntu. It did not work.
I then researched and found this blog post: http://okomestudio.net/biboroku/?p=1360
So I downloaded the pkgbuild for the arch linux core kernel and checked the config. It matched the recommendations.
Another hint I found was to unload acpiphp and force-reload it. However, this tip does not seem to apply to the arch kernel:
[user@3-arch:~$ sudo rmmod acpiphp
rmmod: ERROR: Module acpiphp is builtin.
Anyone any idea on how to make the card work?
Thank you!
Last edited by archery1234 (2014-11-15 10:46:35)

For anyone else seeking help on that: Card slot was deactivated in 2/3 Bioses.

Wireless pci card - not working under OS 9

Hello everyone,
I very rarely post on OS 9 sub board, but I have one quick question. First off, my mac is a powerful(to me it is!) 2003 MDD dual 1.25(last before G5) and has 2GB memory with 2GB L3 cache per processor.
Now thats out of the way. I would like to know if the Belkin F5D7000 card(wireless-G 802.11g) supports working under OS 9.2.2? If Belkin does not have a driver for it, is there a generic driver I can install which would allow my wireless card to work under OS 9.2.2? Yes, I have the FW400 based system, however I might consider going with the FW800, but I would like to know really what the big differences are between the FW400 and FW800 machines?
I know the FW800 has ONE FW800 port, has a slot to support AIRPORT EXTREME card(though my machine has a PCI Belkin F5D7000 wireless-G airport extreme card). It also has support for bluetooth which I wouldn't really use anyway since I have no device to make use of bluetooth.
So, my question really is, is there a way to get the wireless card to be recognized under OS 9.2.2 even though Belkin does not have a driver for it? I really would like to use OS 9.2.2 sometimes, but its useless to me if I can't get on the i-net, and regular ethernet is NOT AN OPTION since where I live is only wireless internet.
Ideas? Suggestions?

Hi,
A ethernet to wifi bridge is connected to your computer via the ethernet port.
ex: http://www.macsense.com/product/networking/wua800-1.html
So there is no need for driver in the OS since it's using the ethernet port like connected via a wire. It's the box that convert it to a wifi signal. You could even use this for OS X, Windows or Linux etc...
Many manufacturers make this kind of device.
A+

AirPort card not working ... mostly

This is one that has me a bit stumped. I have a G3 iBook with the original airport card installed. Yesterday, it stopped recognizing any wireless networks in the local area (I have one graphite ABS and one AirPort Express, plus there are one or two other wireless network around here I can normally at least see). My other portable (PowerBook G4 12") sees all these networks fine. I re-seated the card in the iBook, to no avail. I assumed it had conked out and started researching replacement cards (quite spendy, as you probably know).
Just today, my iBook started recognizing wireless nets again ... briefly. For about five or ten minutes, I saw a few networks and actually was able to access the WAN. After then, though, it's back to not working at all. Has this happened to anyone? Was it the last, final gasp of my venerable airport card? Or if this has happened to you, did you find that it was another problem entirely?
Thanks for any help.
iBook G3 Mac OS X (10.4.4)

Appelfan,
I had gotten frustrated with the random behavior and posted a question about the possibility of an USB dongle wireless solution for the Mac. Duane answered me and gave me a very helpful suggestion - that I consider Ethernet Wireless Adapters, and even mentioned a couple of brands - just in case you may consider that route. I have copied his responses to me, below:
Thank you,
Gino
Duane
Re: Is there a USB Wireless Dongle or card for a Mac?
Posted: Mar 24, 2006 5:33 PM in response to: Gino La Pointe
An alternative to USB wireless adapters is Ethernet wireless adapters. Those require no drivers and therefore will work with any Ethernet device regardless of OS.
Duane
Re: Is there a USB Wireless Dongle or card for a Mac?
Posted: Mar 25, 2006 11:14 AM in response to: Gino La Pointe
Examples of Ethernet wireless adapters are the Linksys WET11 and Linksys WET54G. There are many more.

Sound Card not working (resolved)

I've got a new system, and the integrated sound card on it isn't working, so I swiped the PCI sound card from my old computer and inserted it. And it's not working. I've pretty much tried every method on the troubleshooting section of ALSA's page on the wiki, without any luck. And yes, this includes unmuting and setting the volume of the sound channels.
Last edited by Falcata (2008-02-08 04:07:53)

I already knew that I had two cards. I added in the second one because the integrated chip wasn't working. Anyways, here's the results of lspci -nn:
00:00.0 Host bridge [0600]: Intel Corporation 82915G/P/GV/GL/PL/910GL Memory Controller Hub [8086:2580] (rev 04)
00:01.0 PCI bridge [0604]: Intel Corporation 82915G/P/GV/GL/PL/910GL PCI Express Root Port [8086:2581] (rev 04)
00:02.0 VGA compatible controller [0300]: Intel Corporation 82915G/GV/910GL Integrated Graphics Controller [8086:2582] (rev 04)
00:02.1 Display controller [0380]: Intel Corporation 82915G Integrated Graphics Controller [8086:2782] (rev 04)
00:1c.0 PCI bridge [0604]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 [8086:2660] (rev 03)
00:1c.1 PCI bridge [0604]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 2 [8086:2662] (rev 03)
00:1d.0 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 [8086:2658] (rev 03)
00:1d.1 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 [8086:2659] (rev 03)
00:1d.2 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 [8086:265a] (rev 03)
00:1d.3 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 [8086:265b] (rev 03)
00:1d.7 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller [8086:265c] (rev 03)
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev d3)
00:1e.2 Multimedia audio controller [0401]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Audio Controller [8086:266e] (rev 03)
00:1f.0 ISA bridge [0601]: Intel Corporation 82801FB/FR (ICH6/ICH6R) LPC Interface Bridge [8086:2640] (rev 03)
00:1f.1 IDE interface [0101]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) IDE Controller [8086:266f] (rev 03)
00:1f.2 IDE interface [0101]: Intel Corporation 82801FB/FW (ICH6/ICH6W) SATA Controller [8086:2651] (rev 03)
00:1f.3 SMBus [0c05]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller [8086:266a] (rev 03)
02:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5751 Gigabit Ethernet PCI Express [14e4:1677] (rev 01)
04:00.0 Multimedia controller [0480]: Philips Semiconductors SAA7130 Video Broadcast Decoder [1131:7130] (rev 01)
04:02.0 Multimedia audio controller [0401]: C-Media Electronics Inc CM8738 [13f6:0111] (rev 10)
Last edited by Falcata (2008-02-07 22:55:42)

Sub form not working when converted from adp to accdb

Hi,
We have migrated MS access 2003 (.adp) applciation to MS access 2010(.accdb). There are few functionalities in the application not working as expected. A form opens on a button click has two sub forms. Applications throws error when button is clicked. run
time error 2467. The expression you have entered refers to an object that is closed or doesnt' exist.
Form_frmmainform.frmsubform.Form.RecordSource = rs
Main form contains sub form and that has another sub form within in. There was a query for the record source whcih ihave replaced with recordset.
But it works fine in .adp version. Could any body help me in this regard
Thanks in advance

Hi All,
Could somebody please help me in this regard.
We have migrated MS access 2003 (.adp) applciation to MS access 2010(.accdb). There are few functionalities in the application not working as expected. A form opens on a button click has two sub forms. Applications throws error when button is clicked. run
time error 2467. The expression you have entered refers to an object that is closed or doesnt' exist.
Form_frmmainform.frmsubform.Form.RecordSet = rs
Main form contains sub form and that has another sub form within in. There was a query for the record source whcih ihave replaced with recordset.
But it works fine in .adp version. Could any body help me in this regard
Thanks in advance

On Demand Sub-Report not working

Hello,
I am using crystal reports xi-r2 I am having trouble getting an on-demand sub-report to work. After much trouble I am able to get the sub-report to work in the designer but as soon as I publish the report and access it from the CRS. It stops working. I can not get the sub-report to come up. Or it opens another window like it is going to show the sub-report but I get the original report again.
My second question is how do I open a trouble ticket now that this has all moved to SAP?
Thanks for your help.
Jeff

As this isn't working in CRS you may want to re-post this to: BusinessObjects Enterprise Administration
www.service.sap.com would be a good place to go to get service

Express sub card not working

Similar Messages

Maybe you are looking for