Extend altready extended network with old dome Extreme?

I want to extend my network with an old Airport Extreme, the dome version. The current network uses a new square Extreme (wired to my MacPro tower), then extends to a Time Capsule. I want to use the old dome Extreme to run a USB color printer in a remote room in the house. Is this possible?

Yes, this can be done, but the entire network would have to be configured for a "static" WDS. This type of WDS has two major disadvantages: 1) All the base stations, including the 802.11n ones, would only operate in the 802.11g Radio Mode, and 2) For every base station added, the overall bandwidth will be cut in half. For this case, with three AirPorts, the total bandwidth would be: (54 Mbps / 2) / 2 = 13-15 Mbps ... around the same as the 802.11b standard.
If you still want to pursue this, I can provide the step-by-step instructions to do so.

Similar Messages

I have a Airport network at home with a Time capsule connected via ethernet cable to modem. Also the network is extended wirelessley with an Airport Extreme. My question is I now wish to add a second Airport extreme but am considering a hard wire connecti

I have a Airport network at home with a Time capsule connected via ethernet cable to modem. Also the network is extended wirelessley with an Airport Extreme. I now wish to add a second Airport extreme but am considering a hard wire connection with 100 ft of cat 6 cable from the Time capsule to the second Airport extreme. Can my network operate properly to extend the network with both a wireless and wired extend functionallity?

I now wish to add a second Airport extreme but am considering a hard wire connection with 100 ft of cat 6 cable from the Time capsule to the second Airport extreme.
Excellent plan.
Can my network operate properly to extend the network with both a wireless and wired extend functionallity?
Yes, but don't get confused about the second AirPort Extreme, as it would not be configured to "extend" a wireless network.....it would be configured to "create a wireless network" using the same wireless network name, security settings and password as the Time Capsule network. Configure the second Extreme in Bridge Mode.
This Apple support document will show you how to hookup and configure the second AirPort Extreme:
http://support.apple.com/kb/HT4260

Extended network with 2 AEBS and 2 AE

I have an extended network with 2 AE Base Stations and 2 Airport Expresses. They are all connected on the 5 GHz band and are 'N' only. The two AEBS are connected through ethernet and the two AE are extended wirelessly. I also have an apple TV, Macbook Pro and iMac that connect to this network wirelessly on a regular basis.
My question is this.... is it possible to assign which AE connects to which AEBS. The two AEBS are at opposite ends of my home on furthest levels apart. I have one in the basement on one end, and one on the second floor on the other. The two AE are in the middle on the first floor in between the bases.
The problem I seem to be having is that they (the two AE) are not connecting to the base station that gives them a good signal. They connect fine, but the BS they are connecting to give them a weak signal essentially making them ineffective in their extension. I want to be able to assign them to the closest BS to make them more effective.
Is this possible?

Sure,
They are actually independent of the apple gear in that they are simply attached as wireless access points to provide for the wireless g side of my network. Their IP's are static and they provide my windows machines and gaming consoles their wireless feed.
The two Airport Extremes and Airport Express's make up the foundation of my 5 GHz wireless N network for my Apple systems. The two airport express's not only extend my network but also work as airtunes devices in my house.
So....the AExpress do not extend the linksys units at all... just the 5 GHz N. The problem I am having is that one of the AExpress units is linking to the AExtreme that is farther away from it....giving it a very poor connection and hence extending a very poor signal. I would like to get it to attach to the closer unit....and would prefer to do it without having to utilize MAC filtering if that is possible.
I have other MBP's and MB's that connect periodically and using MAC filtering would be a pain.

Is there a way to connect an old Sunflower iMac (OSX 10.4.11) to a new Time Capsule? It used to work with old Airport Extreme with updates thru Snow Leopard but now seems to only allow WEP encryption instead of WPA.

Is there a way to connect an old Sunflower iMac (OSX 10.4.11) to a new Time Capsule? It used to work with old Airport Extreme network, run from a intel iMac with updates thru Mavericks but now seems to only allow WEP encryption instead of WPA and can't connect to Time Capsule. Airport Extreme Base was controllable from either computer up through Snow Leopard (I didn't do any of the Lion upgrades). Then when I upgraded to Mavericks I lost the ability to use Airport Utility with this hardware on the Sunflower but could still connect wirelessly to network without any problems. But now with the Time Capsule upgrade the Sunflower is blocked from network by a dialogue that requests ony WEP password, not WPA pwd used by Time Capsule. Neither can I use the old airport extreme base to extend the time capsule network since I can't input the correct password/encryption approach to join it. Is there a work around? Would a newer but old Airport Express be able to extend network to Sunflower? Or maybe a third party wireless (such as Netgear, Dlink, etc) that has browser type control rather than special utility?
Another question--before I used MAC addresses to control who could access network. Now on Time Capsule I don't see anything about this--so is it true now that the only access control is via WPA2 pwd now (which appears to be the encryption pwd and not the time capsule pwd)?

Is there a way to connect an old Sunflower iMac (OSX 10.4.11) to a new Time Capsule?
I can’t claim to completely grasp the issue(s) you’re describing, but the underlying problem is presumably your iMac’s obsolete AirPort card. Whatever the case, an obvious (if not particularly helpful) answer to your stated question would be to connect your iMac with an ethernet cable, using powerline adapters as an alternative if you don’t want to have wire running all over the place.
My still fully functional clamshell iBook, with an original AirPort card, connects wirelessly to my 4th Generation TC network by means of a cheap 802.11b/g/n USB Wi-Fi adapter. This might be an option for you too.
Another question--before I used MAC addresses to control who could access network. Now on Time Capsule I don't see anything about this
When you edit your TC's settings the access controls appear under the Network tab, don't they?

How do I set up a wireless network with an AirPort Extreme base station and two airport extreme but between apple devices either by ethernet

How do I set up a wireless network with an AirPort Extreme base station and two airport extreme but between apple devices either by ethernet

This Apple support document provides good general information on configuring different types of neworks using multiple AirPort routers.
http://support.apple.com/kb/HT4145
In particular, you would want to focus on the information regarding a "Roaming Network"

Can I use the Ethernet Port for a computer when it is also used as a wireless network with an Airport Extreme as the access point for the wireless network

Can I use the Ethernet Port of the A1264 Airport Express to connect to the Ethernet port of a computer that does not have wireless capability when the Airport Express is also used on a wireless network with an Airport Extreme 5th generation as the access point for the network?
I have AE 5th gen
looking to buy (from ebay) the AEX A1264
Various computers, printers and hubs for the network
Is this possible to do?

Bob, Thanks for the info. I have read different articles that said yes, but I wanted to make sure before I commit to buy. I have an older A1084 which I could not use the Ethernet port. I know at one point I was able to when I was on 10.4. Now that I am on an Intel processor and 10.8 I am going to have to upgrade some of my Apple wireless hardware.
Thanks Again.

Turn on icloud with my ipad, it spams my network with old meeting requests (2009). what gives?

turn on icloud with my ipad, it spams my network with old meeting requests (2009). what gives?

This happened to me (twice) when iCloud first came out -- and I have steered clear of iCloud ever since. But I just recently upgraded to Mavericks, and they took local sync away!! Anyone still having this issue with iCloud?? I will not send accepted messages for old meetings three times!

How do I extend a network with an AirPort Extreme from an Arris TG862?

I'm using Comcast as my ISP, and after some issues with a previous Motorola modem, they supplied me with an Arris TG862 Router/Modem combo tower. I have two AirPort Extremes, one of which was previously connected to the old Motorola modem to send wireless into the house, but it only reached halfway, so I had the other AirPort Extreme in the middle of the house to "catch" the signal and then broadcast it out to the rest of the house. This worked fine for a while.
But with the new TG862, it doesn't seem to be an option. From what I've read, if I have the TG862 in one room (connected to the cable), AirPort Extreme #1 in the middle of the house, trying to join the existing network (or extend it?), and AirPort Extreme #2 in the far end of the house (to extend from AirPort #1), it won't work. Apple's "extension" technology isn't compatible with all other modems or routers, and even if it was, I'd have to somehow configure the TG862 to "allow to be extended."
So my question is, IF there is a desktop utilizing the TG862 as a direct connection (because it has no built-in Wi-Fi), is it possible to put the TG862 into bridge mode, connect one of the AirPort Extremes and have it act as the router so I can use AirPort Extreme #2 to extend that network out to the rest of the house? I want to ensure the desktop still has a connection, but there's Wi-Fi that actually goes out through the whole house.
The connected-to-the-cable-desktop is a PC; we have multiple iPhones, iPads, and anywhere from 1 Mac laptop to 1 iMac in the house at any given time.

pcbjr wrote:
Topic title pretty well sums up the question.
I have a TimeCapsule Base Station with two Expresses for extending the network through the house.
We're doing a 3 room addition, and there is not a convenient place to put an Express in a wall outlet in the middle room of the addition, but there's a perfect place to put an Extreme on top of a piece of furniture.
So, can the Extreme act as an "extender" only, in lieu of using an Express?
Hiya.
You can absolutely extend a network with an Extreme. I've got a 5th gen. Extreme extending a network created with a 3rd gen. Time Capsule. On the Extreme, you'll have the option to allow (or not) WiFi clients. I recommend having all units updated to the current firmware (7.6.1 as of this writing). Note that extending doesn't work in daisy-chain fashion, meaning that your Expresses or Extremes will each connect to and extend from the TC. As such, you'll want the TC to be in as central a location as possible to offer the best coverage.

Extending network with Airport Express and Airport Extreme (latest models) causes chaos on network

Today I upgraded from my several year old Airport Extreme (3rd gen) and 2nd gen Airport Express to a new (what you'd buy on the shelf today) Airport Extreme and Airport Express. All airports are updated with the latest firmware and I'm using windows 7 for configuration.
The intention is to use the Airport Extreme as the main router, also serving wifi. And extend the network using the express. As such, the following has been done:
The Airport Extreme is configured for automatic channel, and automatic radio mode. I tried to select 802.11n 5 ghz and 802.11 n 2.4 ghz only, but it won't take the changes. Additionally, it wont' accept me using only channel 6. Not sure why, but I digress. The airport extreme is not set to broadcast a separate name for the 5ghz network.
The Airport Express is configured to use bridge mode, use an existing wireless network and is connected to my network on it's WAN port (the circle icon on the back) with ethernet. The password and wireless name used in configuration is the same as created initially on the Airport Extreme.
Initially I did the configuration of both airports on my computer, connected by ethernet to ensure stable connectivity while I inputted settings. During this, they appeared to accept the changes fine. However, when I moved the airport express to it's destination (other side of my house), the entire network went crazy.
Internet became slow, and often wouldn't load pages. This was on wired and wireless connections. When I attempted to administer the Airport in the Utility, they would not load, an error would occur. Also, at one point the Airport Extreme had renamed it self with a (2) at the end. Which was super odd. So far, the only solution has been to unplug the Airport Express and attempt to devise a solution.
Anyone have any ideas? Of course, I will continue to tinker with this, but it seems realllly strange. The previous setup was also extended (granted, using wireless only, not ethernet > wireless) and worked fine, granted it was a smidge slow, but it worked.

I wanted to add this.. I followed the guide here: http://support.apple.com/kb/HT4260 to extend using ethernet, and the above is the result.
I just tried re configuring in OS X Mavericks and got the same, odd, result.

Extend network with AE 2 Antenna Model over Old AE?

Would there be any benefit to using a new dual antenna AE over an old one with a single antenna? I have a mix of new and old Macs as well as an iPad 2. I am also using an Airport Express as last device in the extended network.

Jazzman wrote:
Would there be any benefit to using a new dual antenna AE over an old one with a single antenna? I have a mix of new and old Macs as well as an iPad 2. I am also using an Airport Express as last device in the extended network.
I am considering the same thing. Benefits as I understand it: the new Airport Extreme or Time Capsules will allow your newer computers to use the 5 GHz band while your older computers and other devices use the 2.4 GHz band. Separate bands should improve performance. Also the older AE may only support 802.11g, but the new AE will allow older 802.11g devices to coexist with the 802.11n service on the updated AE2. Or so I hope...
If your older AE only supports 802.11g, then you will also see greater range and performance moving up to 802.11n. That’s the main problem i’m tackling as my old router doesn’t provide very good coverage in parts of the house and the iPod touch frequently loses its wireless network signal. I considered Airport Express to extend my network but like the idea of having the dual bands available.

Can I extend a network with an AirPort Extreme Base Station Rather than with an Express?

Topic title pretty well sums up the question.
I have a TimeCapsule Base Station with two Expresses for extending the network through the house.
We're doing a 3 room addition, and there is not a convenient place to put an Express in a wall outlet in the middle room of the addition, but there's a perfect place to put an Extreme on top of a piece of furniture.
So, can the Extreme act as an "extender" only, in lieu of using an Express?

pcbjr wrote:
Topic title pretty well sums up the question.
I have a TimeCapsule Base Station with two Expresses for extending the network through the house.
We're doing a 3 room addition, and there is not a convenient place to put an Express in a wall outlet in the middle room of the addition, but there's a perfect place to put an Extreme on top of a piece of furniture.
So, can the Extreme act as an "extender" only, in lieu of using an Express?
Hiya.
You can absolutely extend a network with an Extreme. I've got a 5th gen. Extreme extending a network created with a 3rd gen. Time Capsule. On the Extreme, you'll have the option to allow (or not) WiFi clients. I recommend having all units updated to the current firmware (7.6.1 as of this writing). Note that extending doesn't work in daisy-chain fashion, meaning that your Expresses or Extremes will each connect to and extend from the TC. As such, you'll want the TC to be in as central a location as possible to offer the best coverage.

Can't extend network with Airport Express on Sky Broadband

Hello,
I'm having some difficulty that's driving me bananas!
I've recently moved house and got Sky Broadband. They sent me their Sagemcom router and the setup was easy. I thought I'd do what I always do. I'll connect my Time Machine to it via ethernet, and connect via Time Machine's network. Then I have two Airport Expresses in the house to extend the network and use Airplay etc.
I can set up the Expresses with no problem, everything talks to everything without a problem and the lights are all green but the network isn't getting extended with either of them. I refuse to believe they're both broken as I also borrowed an Express form my Dad's house (which extend the network without a problem) and it doesn't work with me.
Extend my network is checked in the Manual Setup in Airport Utility but for the life of me I can't get my network extended.
I have done tests where I replaced Time Machine and made one of the Expresses the main base station and it throws signal out easily like that but I can't extend that network with the second Express.
I followed this thread https://discussions.apple.com/message/13171691?messageID=13171691 and have tried a few things to no avail. Currently I have configured an old Airport Extreme (just to keep testing) which works great and have set up an Express wirelessly. All lights are green and the settings seem to all be correct. I turn wifi off on my computer and connect to my computer from the Express using ethernet and nothing. Should I get a connection like this?
Is it Sky? I have read in a few places that Sky have disabled the ability to extend their network but I'm not eve using the signal from their box.
Any ideas or thoughts will be gratefully received.
Thanks in advance.

OK so I've been tying it out but unfortunately to no success. Everything looks fine and all lights are green but the network isn't getting extended - just as before.
Click the Wireless tab
Wireless Mode = Extend a wireless network
Wireless Network Name = Same name as the Time Capsule network
Check Mark next to Allow Wireless Clients
I don't have an option to extend a network, only to join: http://flic.kr/p/a222kR
I do get the option though if I use the guided setup, even though it doesn't work: http://flic.kr/p/a24TQQ
I did try one other thing though. I set up the Time Capsule and it works great. Then I tried instead, to use my Airport Extreme to extend the network. The Extreme did give me an option to extend the network in the drop down menu and a checkbox to Allow Wireless Clients, unlike the Express. I do believe that this is now working. I now need to find the best place to put it to extend the range.
My Expresses are only 802.11g so they're pretty old but as I said, it worked at my Dad's house but not here. Does it make a difference that the Airport Base Station at my Dad's house is an older UFO shaped Snow Airport? I'm becoming suspicious that seeing as I've only ever lived in small houses and apartments that maybe they never worked?? I've recently moved into a more spacious house so could this be the problem?
One final test using iStumbler showed that it could see Apple Network XXXXxX until I configured it. Once it was configured it disappeared from iStumbler. The Airport ID number had gone from the list.
Do I need newer n compatible Airport Expresses then? So many questions pop up now... When I turned my Express into the base station (which only throws out a g network) then surely I should be able to extend to the next Express (which is also g only)? It still didn't work. The Express are on version 6.3 by the way. Having the Extreme extend the network is a good start but I also need the others to work too. Do you think I'm correct in my assumption?
How about WDS, could that work? Will WDS slow the network considerably?
Sorry if this message is rather long and garbled and again, thanks for your interest and advice.

Can I create an extended network with a brand new TC and 2 first gen. AE units?

I purchased a TC 2TB yesterday and replaced my non apple router with the TC. I have 2 older AE units that I suspect to be first generation. TC is in basement and I have placed AE in garage where I spend most of my time. Signal in garage is weak and lags. Air tunes off of AE in garage connected to boom box works fine. I run AirTunes from 3 iPhones, iPod touch, and 2 iPads with no problems. The options in manual setup for the AE don't offer make this an extended network, I suspect because they are too old? I don't want to create a WDS network and sacrifice the bandwidth. My main machine is an iMac 27 that is one year old, this is in the kitchen pretty much midway between the TC and the AE in the garage, if that makes any difference?
Any help is greatly appreciated.

The options in manual setup for the AE don't offer make this an extended network, I suspect because they are too old?
Please take a look at the faint print on the side of both AirPort Express (AX) devices that you have to identify the Model No.
You will need # A 1264 to do what you want. If you have # A 1084 or similar, the devices that you have are not compatible with the "extend a wireless network" setup.
What are your findings?

Extending Network with Airport Expresses?

I'm drawing in wifi signal from the shipyard and want to broadcast(extend) it throughout the lower sections of a boat.
Currently I have 1 airport express drawing in the signal with ethernet connecting to the computer. However I want to extend the current network. Can I do this by buying another Airport Express and connecting through ethernet cable to the one I currently have. Would this work? What options would I need to select with the new AE(extend network, create network, etc)? Would this work with an airport extremeas well.
Any help much appreciated.
Ash

Tessarax,
Are you saying I would need three AXn to create the extended network? or would it just work with 2?
ie
AXn(Recieving)-----Ethernetcable-----AXn extending network
Will this not work?
Sorry just want to know how much I'm in for and if it will work before i go out and spend it.
Thanks for the reply
Ash

Creating and Extended Network with 2 Airport Express Units

I had an extended network using 2 express units but one of them broke. The old network was setup with an older version of Airport Utility and I can't seem to repeat the set up a new network with the new express unit I have bought.
The simple setup procedure using Airport Utility 5.5.1 only appears to allow you to 'join' the remote Express unit to an existing network, there is no 'extend remotely' option.
I remember doing it last time by creating a WDS network which agrees with instructions I have found here - http://broadcast.oreilly.com/2009/03/taming-an-airport-express-wds.html
I set up the first Express as a base station with a network and select 'Participate in a WDS network' and 'Allow this network to be extended' under the wireless tab. Under the WDS tab I 'Allow wireless clients' and add the hardware address of the second express unit.
I then update the express unit but I get a WDS error which states, "This Airport wireless device is set up as part of a WDS network but no other AirPort wireless devices were found."
This seems to be a chicken and egg situation.
Any help would be appreciated.
Alan

Alan, welcome to the discussions!
It appears that you want to set up a WDS arrangment, correct?
But, I can't figure out whether you want to configure it with a "base" and two "remotes", or whether you want to configure it with a "base", "relay" and "remote"
Can you clarify? I'll send you a link with instructions from forum expert user Tesserax with step by step instructions. Just need to know what set of instructions to send.

Extend altready extended network with old dome Extreme?

Similar Messages

Maybe you are looking for