Extend existing wireless network with airport express..impossible?

I have tried to extend my existing wireless network with an airport express, but it seemd that I always need a ethernetcable...apple support insured me it is possible but the airport utility software only allows me to extend using a cable it seems....

Couple of thoughts here.......
The AirPort Express will only extend a wireless network if you have another Apple router providing the wireless network to be extended.
Is your "main" wireless router an Apple product? If yes, what model number do you have?
It would also help if we could get the model number of the AirPort Express. Some older versions are not capable of extending a wireless network.

Similar Messages

Extending Snow wireless network with AirPort Express

I am trying to extend my existing Snow network with an AirPort Express, which I will connect to the Snow (through an unmanaged ethernet switch) via an ethernet cable. I think I know how to do this but if anyone has any hints, they would be appreciated.
In addition to using the AE as an "extender/wireless access point," can I also configure the system to stream AirTunes to the AE through the ethernet cable at the same time?
Thanks

Oops, sorry I misread your post. That should work. Make sure that you disable the "Distribute IP addresses" option on the AX so that it acts like a wireless access point. On the AX, just enable the "Enable AirTunes over the Ethernet port" option on the Music tab.

I have installed Airport Extreme on my iMac, but want to extend the wireless network with Airport Express. Everything is fine until I try to select Extend the wireless network. I select Extend Wireless network but have no success. Ideas?

I have installed Airport Extreme on my iMac, but want to extend the wireless to rooms with a weak signal. The internet connection is fine with the basic setup. As soon as I go into Airport Utility to select Extend Wireless Network and fill in what I believe is proper information, I get an error message that Airport Extreme no longer has an IP address, the internet connection is broken, and under Wireless, that there is a wireless network in existence that can't be found. Rebooting the modem only brings the Airport Extreme back to the starting gate so that the internet is once again available. I assumed (naively) that with the All Mac All-the-Time context, adding Airport Express would truly be Plug and Play. I got the plug, but no play. I asked a Comcast technical specialist about it and he said that I needed to reset the Airport Express settings back to their default, factory status. I looked that process up online and found out that the way to do that was to hold down the reset button, then plug Airport Express into the socket and wait for the green light to flash four times. Then wait 45 seconds and the default settings will return. I did all that, only to find out that after the initial flash of green, green never appeared again. I got a fast flashing yellow light, followed by the light going off. Apparently this didn't reset it properly. So, after hours trying to get this system to work, I appeal to someone who can see through this mess and provide the key to success!
highFly376

Let's see if I can get this straight.
You have an Airport Extreme base station that is set to "Create a wireless network" and you have the box checked for "allow this network to be extended"....
Then you have an Airport Express that is set to "Extend a wireless network" which you selected the name of your network in the box...
Correct?
See this Apple document:
http://support.apple.com/kb/HT4259?viewlocale=en_US&locale=en_US
The wireless unit on the right of the diagram can be either of the newer Apple base stations.
Extreme, Express, Time Capsule

Extending Sky Wireless Network with Airport Express.

I spent most of last night trying to extend my Sky Wireless Network using an Apple Airport Express. The Apple Store salesman told me that it would be simple to set up but he's either wrong or I'm completely stupid!
Does anybody know if this is possible and if so, can they please advise me how I do this. (I am using Windows 7 on my Dell laptop)

I spent most of last night trying to extend my Sky Wireless Network using an Apple Airport Express. The Apple Store salesman told me that it would be simple to set up but he's either wrong or I'm completely stupid!
Unfortunately, the salesman may not have understood your question, or he may have given you incorrect information.
It's possible to have the AirPort Express provide more wireless coverage if you connect it using an ethernet cable permanently to your Sky router.
But, the AirPort Express cannot "extend" the wireless network produced by the Sky by connecting using wireless only. The "extend" feature will only work if you have an Apple to Apple wireless connection. This feature is not compatible with the products of other manufacturers.

Joining an existing wireless network with airport express

Ok, am almost to the point of throwing my AX across the room
AM trying to join an existing wireless network, its from a 2Wire gateway
one of three things happen
it won't find the AX in the first place
it recognizes it, but i can't connect to it
it goes through the configuration and when it restarts the AX, it can't reconnect to either the router or the AX and it fails. if this happens i can't reconnect to my wireless network without deleting it and re-adding.
it doesn't show up in my available wireless networks at all
protected via WEP, and i have tried using all the security options.

The directions are in KB 302153, AirPort Express: How to join an existing wireless network in client mode.
Are you using MAC address access control in addition to WEP?
Turn off WEP and see if that makes a difference?
One of the problems with WEP is that the actual standard relies on a 10 character HEX key for 40bit WEP and a 26 character HEX key for 128bit WEP.
In order to make things easier for people, vendors use certain algorithms to convert simple alphanumeric passwords (or passphrases) into HEX keys, thus enabling people to use simple memorable WEP password rather than lengthy HEX keys.
The problem is that different vendors use different algorithms to generate the HEX key and therefore a ASCII password on an AEBS will be hashed differently on a Netgear client and vice versa.
One thing is a 13 character 128 bit WEP password will be hashed by all vendors in the same way (if you use 40bit WEP then a 5 character password is required).
Though sometimes not even that works and the HEX key must be used regardless.
Choosing a password for networks that use Wired Equivalent Privacy (WEP)
http://docs.info.apple.com/article.html?artnum=108058
WEP is now considered not to be secure and therefore it is advised you use WPA.
"WPA Personal" on the Mac corresponds to plain WPA, with a pre-shared key (PSK) and TKIP encryption, on non-Apple wireless routers. The same alphanumeric password should work on both.
iFelix

How do I extend an existing wireless network using airport express?

Hi all,
I am trying to extend existing wireless network using airport express, my main router is Belkin

Unfortunately, Apple's "extend" feature is designed to only work with other Apple routers if you are trying to "extend" using wireless only.
It is extremely unlikely that this feature would work with a router from another manufacturer using wireless only.

Extend wireless network with AirPort Express

How to extend the wireless network with AirPort Express and Belkin PlayMax as the primary router ?

How it work if I have an AirPor Station and 4 Airport Express, I actually also have an old TimeCapsule and an old AirPort Express. Can I cover all my house (around 300 m2). And will the old Airport slow down or convict with the new ones?

How can I extend my wireless network using Airport Express and an Airport Extreme on BT Infinity?

I have BT Infinity and I am using the Time Capsule with Airport Extreme as my router. Working well (even on wireless). I want to extend the wireless network with an Airport Express, but I cannot work out the settings necessary in Airport Utility. I am using Mountain Lion 10.8.2 on a Mac Pro. Please help!

BT,
I've read several of your posts, thanks for taking the time to share your wealth of knowledge.
I'm in a situation similar to the one described by 'scoutusmaximus'. Seeking the flexibility of a standalone router, I finally upgraded my 4-yr old ATT DSL gateway (modem+router) to a Comcast standalone modem + the ASUS RT-AC66U: http://www.asus.com/Networks/Wireless_Routers/RTAC66U/
Typically, I stick with all things Apple but the ASUS router seemed fairly superior to the current-gen base station (on paper, anyway; time will tell when it comes to performance) so, for once, I jumped ship. My plan was to extend the ASUS wired/wireless network using my TimeCapsule and 2 Airport Expresses in bridge mode, however, a google search turned up several unhappy customers that claim those devices don't play well with non-Apple routers, especially when it comes to 'extending' a network.
Questions:
1. Can I successfully extend the wired/wireless network created by the ASUS router using the 3 airport devices listed above w/out negatively impacting performance? I'd rather have 1 wireless network as opposed to creating a new wireless network with the TC and then extending it with the AP Expresses... though I'd consider that option down the line if it came to that.
2. Will the LAN ports on the TimeCapsule remain functional?
Btw, my house is wired so, I can reach all 3 devices via ethernet cable coming off of a central, managed switch. Supposedly, you only lose the LAN ports on the TC if you extend wirelessly.
Any advice would be appreciated.

Extending Gen 1 Time Capsule Wireless network with Airport Express N

I am having difficulty setting up my new Airport Express w/ 802.11N (SKU# MB321LL/A) to extend the wireless network from my Time Capsule (SKU# MB276LL/A).
My setup is as follows:
Time Capsule is connected to Cable modem with the following wireless settings:
Wireless mode -> Create a Wireless Network
Allow this network to be extended -> Checked
Radio Mode ->802.11n (5Ghz N only)
Wireless Security -> WPA2 Personal
The issue is the when I attempt to setup the AE to extend the network. I match the settings to the Time Capsule:
Wireless Mode -> Extend a Network
Select the Time Capsule Network
Allow wireless clients -> Checked
Wireless Security -> WPA2 Personal
However after I reset the AE the LED glows Amber and the following problem is reported:
+Wireless Network+
+This AirPort wireless device is set up to join a specific wireless network that can't be found. If you don't see the network that you want to join in the Network Name Pop-up menu, enter the network name and network password if necessary to try again.+
When I check the Airport->Wireless tab the settings were as before.
Any thoughts on this? Thanks.

Welcome to the discussions!
Have you tried to position the AirPort Express close, say 10-15 feet, as a test to see if it will connect that way?
If so, then move it back another 10-15 feet, etc.
5 GHz signals do not travel well or penetrate surfaces very well, so my first thought was that the signal was not strong enough for the Express to pick it up where you had it located.
Message was edited by: Bob Timmons

Extend a non Airport wireless network with Airport Express

I want to use an Airport Express to extend a wireless network which is not an Airport network. The wireless is being provided by a wireless router. I tried setting up WDS, but that requires a wireless network. How do I extend the wireless network without it being an Airport Base Station? Can I?
Thanks.

I'm trying to extend an 802.11g network. The base access point is a SpeedTouch which supports WDS. My Airport Express happily connects to the network as a regular node, but I can't get the WDS to work. Do you know of a way to set this up?
Thanks!
JP

Extend Linksys WRT160N wireless network with Airport Express

First off, I'm a network simpleton, so please keep that in mind!
I've seen similar posts, but I'm not sure definitively if this is possible. Trying to extend the wireless network from a linksys wrt160N with the airport. Is this possible without a phd in network engineering? If so, are there step by step instructions someplace that can help me?
I really appreciate any direction!

Welcome to the discussions!
I'm assuming that you are trying to do this using wireless only.
Apple's "extend a wireless network" feature will only work if both the main router and extending device are Apple "n" devices. Unfortunately, this feature is not compatible with devices from other manufacturers.

Connect to Existing Wireless Network Using Airport Express?

I would like to use my airport express to connect to an existing wireless network set up in my apartment. The wireless router (linksys) is set up in my roommate's room to his desktop. I have a printer in my room and would like to use the airport express to connect to this existing network so that my roommates and i can print wirelessly. I need to keep the printer in my room.
Is there a way to do this? Please advise.
Thanks.

Is the LinkSys a WRT54G? If so, you have two options. If not, only the first option below is available to you:
1. You can configure the Express to connect as a wireless client. You won't be able to connect wirelessly directly to the Express in this mode; you have to connect through the router.
2. With the proper firmware in the WRT54G, you can set up a Wireless Distribution System (WDS). In this configuration, not only can the Express be used for printing and AirTunes, but it will also extend the range of your wireless network.

Extend my wireless network w/airport express w/out connecting via ethernet?

Here's what I have:
I have an Airport Extreme Base Station Version 7.5.2 - named Jim's Base
I have an existing Airport Express that I use to stream music to my office stereo - named Jim's Office
I have a new Airport Express that I would like to use to extend my wireless network to my family room - named Jim's Extended. I have ethernet to my family room for my TV and Receiver and an ethernet switch with one available port.
Question, when extending my existing wireless network do I have to extend it using an ethernet cable or can it be extended "wirelessly" i.e. no connections except to 120v power?
Could someone share the exact instructions? I've been trying to configure this "extension" for several hours now but can't seem to get it to work - wired or wireless.
Thanks -
jP

Apple's instructions to "extend a wireless network" using wireless only are in the link below. Although the illustration pictures a 2nd AirPort Extreme, the setup for an AirPort Express is exactly the same.
http://support.apple.com/kb/HT4259
The Ethernet port is automatically enabled in this type of configuration to allow Ethernet devices to connect. If you need more than one Ethernet connection, you can add an Ethernet switch to the AirPort Express to create more connection capabilities.

Unable to extend existing wireless network with new TC

I have an original 500GB Time Capsule that I've been using successfully for a long time. It is plugged into my modem/router (which acts as a DHCP server) in bridge mode.
As the TC is getting full (and the number of Macs in our house is increasing!), I decided to buy another TC - this time the latest 2TB model. I have set it up so it extends my existing network. However, as soon as I plug it into my network my Internet connection breaks (or goes very slow) and the modem/router activity light flashes like crazy. As soon as I unplug the new TC from my wired network, I get my fast Internet connection back and the modem/router goes back to normal.
I've tried using the LAN and WAN ports on the new TC to connect to my wired network but the result is the same.
Has anyone any ideas what the problem is? Is there a problem using the latest TC to extend the wireless network of an older model TC?

Welcome to the discussion area!
If you are connecting your Time Capsules using an ethernet cable, you would connect from one of the LAN ports on the "main" device to the WAN port on your new 2TB device.
The 2 TB device must be configured as a "bridge".
You would configure the 2 TB device to "create a wireless network" using the same network name (SSID), security setting and password as your "main" device. (The "extend" setting is only used if you are connecting your devices using wireless only...and you are using ethernet).
When you "create" the wireless network on your 2 TB device, you are configuring what is known as a "roaming" network. Your laptop will automatically connect the device with the strongest wireless signal depending on where it "roams".
To configure your 2 TB device as a bridge:
AirPort Utility > Manual Setup > Internet icon > Connection Sharing setting = Off (Bridge Mode).
Please post back on your results.

Establishing a wireless network with airport express

Can someone please help me setting up a wireless network?
I'm using netgear DG834GT and want to set up a wireless network with my airport express. Unfortunately i cannot set it up and need someone to help.
Thank You

If you want to configure an Airport Express to work with the existing wireless network created by your DG834GT wireless router, then follow the advice posted here by David Lovel (the advice is applicable to both Mac and PC users):
David Lovell, "Airtunes for XP with a Wired/Wireless network" #1, 09:05pm Jan 8, 2005 CDT
I hope you really did mean to say you were using an Airport Express. Don't confuse an Airport Express with an Airport Extreme card - the Airport Extreme card is the name of the wireless adapter built into your Powerbook.

Extend existing wireless network with airport express..impossible?

Similar Messages

Maybe you are looking for