Extend network airport extreme

I need to extend my Airport Extreme network. I purchased another Airport Extreme but don't find instructions on how to use it to extend, only how to use it as a base station.

Apple's instructions to do this are right here:
http://support.apple.com/kb/HT4259

Similar Messages

How do I extend my AirPort Extreme network using airport express

How do I extend my AirPort Extreme network using airport express

see http://support.apple.com/kb/HT4145 and other support articles
and/or
https://discussions.apple.com/thread/4462789?start=0&tstart=0
and many other discussions on this forum about this topic.

Airport Express to extend my Airport Extreme network

Puzzled at set up of my new Airport Express to extend my Airport Extreme network. Just trying to increase range. [Extreme works fine.]

We are going to need a bit more info in order to help.
Do you know if your AirPort Extreme is a newer dual band model? Check the Model Number on the bottom of the device if you are not sure.
Are you still using the OS X 10.6.8 operating system on your Mac as your profile indicates?
If no, what operating system are you now using?

HT4259 Q: Can I use an older Airport Express-g router (not -n) to extend my Airport Extreme-n wireless network? If Yes, are the instructions the same as for adding an Airport Express-n router?

Q: Can I use my older Airport Express-g router (not -n) to extend my Airport Extreme-n wireless network? If Yes, Are the instructions the same as for adding an Airport Express-n router?

If you want to extend, using wireless only, the 802.11g Express doesn't support this.
However, if you want to use bridge mode over Ethernet or Powerline adapters then this is supported.

How do I extend my Airport Extreme version 5.7 for better wireless at a distance?

From my researching of this problem, it seems like I may need to "extend" my Airport Extreme version 5.7 to strengthen my signal at a distance. It is used, but I was able to reset and set it up to my network. The previous user was getting much better performance. When at my desk, right next to the router and Airport Express, I get up to 19Mbps. At a distance of 30-50 ft. (which I often use) wirelessly, I can only get up to 4Mbps. Will "extending" the Airport help those speeds and strengthen the connection so as not to burden it even farther with 3 users connected to the network or is there something else that I can do? Am I just being picky? I am an Apple novice and have read everything I can to figure out my problems, but this one is still lingering. Problem or not?
Info: if needed
Airport Extreme v 5.7 - only one as a base station
Wireless network with ZyXel Q1000 router - Airport Extreme is connected to that via ethernet cable.
I use a Toshiba Satellite laptop, less than a year old running Windows 7.
Often work about 30-50 feet away wirelessly and speeds are up to par without Airport Extreme, got it to strengthen signal as another user will be added to my network shortly. Speeds at a distance 4Mbps or less. Next to router and Airport 19 Mbps.
I have Century Link 20Mbps high speed internet service.
Airport "dome" has three lights on top. Middle is steady green and the two on each side periodically blink white.
Successfully set up using airport utility for PC. It shows up on that list and on my wireless connection list.
Thanks in advance for any and all suggestions or positive comments.
david
badboyfun - apple novice.

I'm having a bit of trouble confirming that the ZyXEL is a combination modem & wireless-N router. If it is, then you really won't get any advantages of using the 802.11g AirPort.
If the range of your ZyXEL is limited, you may find that doing either or both of the following will help: 1) Move the ZyXEL so that it is higher vs. lower in the room, that is away from any closed areas or placed in a metal cabinet, and 2) Changing radio channels. The latter is especially important in you live in an area where there are a number of competing Wi-Fi.
A good utility to find out, is iStumbler. You would use this to find these other Wi-Fi and find which have the strongest signal value. Those that do, you would also want to note which channel they are operating on, and then, change yours to one that is at least 3-5 channels away. So, for example, if you find strong ones on channels 1 & 6, change yours to 11.

I am extending my airport extreme by adding an airport express. I had no problem setting it up and got green lights but now I cannot get on either because it says it is a self assigned IP?

I am extending my airport extreme by adding an airport express. I had no problem setting it up and got green lights but now I cannot get on either because it says it is a self assigned IP?

i am extending my airport extreme by adding an airport express.
Does this mean that you are connecting the AirPort Express to the AirPort Extreme using a wired Ethernet connection....or....are you connecting the AirPort Express to the AirPort Extreme wirelessly?
but now I cannot get on either because it is a self assigned IP?
I suggest that you first concentrate on getting the AirPort Extreme working correctly. Power off the modem and both the Extreme and Express, wait a few minutes, then power up the modem and let it run a few minutes. Then, power up the AirPort Extreme and check the network for proper operation. Leave the AirPort Express off for now. Report on your results.
We need to know what operating system you are using on your Mac or PC in order to provide more troubleshooting help.
If you have a Mac and do not know what operating system you are using, click the Apple icon in the upper left corner of the screen, then click About This Mac. Post back with the OS X version number that you see there.

Can i use a cisco RE1000 range extender with airport extreme

Can I use a Cisco R1000 range extender with airport extreme?

Apple's "extend a wireless network" function appears to be a proprietary feature that will only work with other Apple routers.
As far as we know, devices from other manufacturers are not compatible with this feature.
Bottom line....It would be extremely unlikely that this would work, but it's worth a try if you already have the products in hand.
Please post on your results.

I am trying to extend my airport extreme signal to another airport extreme can this be done? I have tried several time using the automated set up but it keeps failing... What am I doing wrong?

I am trying to extend my airport extreme signal to another airport extreme can this be done? I have tried several time using the automated set up but it keeps failing... I have selected every possible security/password encryption level... What am I doing wrong? If it os possible where can I find step by step instructions? Please & Thank you!

The challenge with the older round AirPort Extremes are that they are "g" wireless devices.
When you configure them for WDS, the speed on the wireless network is cut in half...and probably will not have the bandwidth required to stream video reliably from either AirPort Extreme since both are affected by the WDS setup.
There is not an "automated" setup for WDS. You have to do this manually on both AirPort Extremes. Unfortunately, it is not an easy configuration and it's easy to make a mistake and hard to recover without starting all over again.
Apple's instructions for WDS are here if you want to give it a try.
http://support.apple.com/kb/HT4262
It is possible that it might work. Keep us posted on your progress
Adding a single AirPort Express will unfortunately not help. You have to have "n" wireless devices at all router points.

How do I add my Airport Express to extend my airport extreme base station network

How do I extend my wireless net work using my new airport express.
My base station is an airport extreme.
I can get both the extreme and the express to show up in the wireless set up system, but it wants to set up one or the other. I want them both working together to extend the range of my base station.

Power up the Express for a few moments, then "hard reset" it iby holding in the reset button for 10-12 seconds and then release. Give the Express 40-45 seconds to restart and you will see a slow blinking amber light when this occurs.
Open AirPort Utility - select the Express and Click Continue to follow the guided setup. You may need to "switch" networks if AirPort Utility presents this option so that you can configure the Express.
The first page of the setup will ask you to assign a name for the device and device password. On the next page select the "join a wireless network option". Select "join" again and then enter a check mark next to the option to "extend the range of the network"
Continue following the guided setup to configure the device and click Update to save your settings.
Close AirPort Utility as soon as you see the message that the settings have been stored. Allow 40-45 second for the Express to restart.
A good location of the Express is a point that is about 1/2 the distance from your AirPort Extreme to the area that needs more wireless coverage. This will insure that the Express receives a strong signal to "extend".

Trying to extend my Airport Extreme network using two Airport Express

Ok, so just an hour ago I had a network working fine that was set up like this:
Modem => Airport Extreme => Airport Express 1 / Airport Express 2
Stupidly I decided to rename one of them, to their specific room location, using Airport Utility 6.3.2, after it came back online it was listed on the utility bliinking yellow, when I hover over it with the mouse I can see the YELLOW DOT next to STATUS: Extend network, if i click on that it gives me the option to A) IGNORE B) EDIT and futher it goes on to say that it CAN NOT EXTEND THE NETWORK, asking me to check if the device is configure correctly/password is correct/or within range.
I have tried everything, reset, factory reset, setting it up again, and it just comes back blinking yellow.
Stupid again: I decided to unplug the other Airport Express, to see if that would help bringing the first one online again, now I have TWO yellow - non-able-to-extend-range Airport express units in the house.
Naturally I am quite frustrated, so any good advice will be very much appreciated, thanks!
The Airport Extreme is version 7.6.4 and serial number 6F8070MYYEW (If that helps anyone), both Airport Express is the latest version.

Hi Bob thanks!l
After about two hours of trying everything, I finally did something that fixed the issue, and since I have been around the block so many times I am actually not sure what it was; but it was a change in the setting on my Airport Extreme, and I think maybe I canged the router mode from DHCP (Is that default) to DHCP/NAT - and after that I was able to bring my Airport Express stations online again.... Weird, and far from the tunrkey solutions I have come to expect from Apple regarding internet connections.
Thanks for helping Bob, althogh I came up with a solution on my own, people trying to help is always very very much appreciated!!
Best
Eirik

Extending my network Airport Extreme - Airport Express

This morninig I took receipt of a new Airport Extreme.
I have setup a new wireless network and I am now trying to extend its range using my existing Airport express units.
I am using the new Airport utility to configure the setup.
After having selected the Aiport network to extend, I then give my base station a new name, click "continue" and get the following error message:
AirPort Utility is unable to set up this base station for WDS because this computer does not have an AirPort card installed.
Which is crazy since I have a new MacPro with a card installed!!
Any ideas?

Are you connecting the new base to your network
(or
computer) via an ethernet cable? If not, try
that.
This is how I ended up configuring my AE-N base,
and
it worked fine. I also configured my Airport
Express stations the same way. This way when the
units restart, they never lose connectivity.
Jeff
Hello Jeff,
I have a mac pro connected to the new base station
via an
ethernet cable. I then have another ethernet cable
which connects the new Airport Extreme base station
to mt DSL modem.
Is that what you mean?
Anthony, did you ever get an answer to this? I'm having similar problems and cannot seem to find someone who has solved them. Please let me know if you've figured out a solution.
thanks!
mIck

Extending an Airport Extreme (6th Gen) network with older Airport Express models

I just purchased the latest Airport Extreme (6th Gen) base station to be my main wifi router. I have two airport express models that I used in the past to extend my network with my (very) old retired Airport Extreme (2nd Gen): the 2nd Gen model A1264 (you plug into the wall directly) - I've had it for several years, and the newest 3rd Gen model A1362 (small square that lies on a desk or table) - I just purchaed a couple of months ago.
My question is - will extending my network with either of these Airport Express models diminish my overall network speed (Especially the older model)?
I don't have any AC capable clients yet - so everything is running on the "n" band - and the older Express is an "n" model, but I just have this (perhaps irrational) fear that attaching older routers will slow everything down.
Any thoughts or suggestions?
Thanks!

will extending my network with either of these Airport Express models diminish my overall network speed (Especially the older model)?
The A1264 model will be able to extend only one band of the new dual band AirPort Extreme. Normally, the A1264 will extend the 2.4 GHz band since it is stronger than the 5 GHz signal.
The A1392 will be able to extend both bands since it is also a dual band model, providing that it is located where it can receive a strong wireless signal from the new AirPort Extreme.
Here, I am assuming that you are asking about extending wirelessly.
You might want to keep in mind that extending wirelessly always involves compromises and loss of bandwidth. The main reason for this is that an extending device can only "extend" the quality of signal that it receives.
The wireless signal from the new AirPort Exterme will slow down and lose strength the further that it moves away from the main AirPort. So, the extending device gets a slower, weaker signal to extend. The result is signficantly slower wireless performance in the extended areas.
The way to solve this is connect the extending AirPorts to the main AirPort using a permanent wired Ethernet connection. There is no signal loss in a wire, so the extending AirPort receives a full bandwidth signal to broadcast. The result is higher and more uniform speed on the entire network.

Extending and airport extreme network with wired connection to a express

I am getting fed up of deadspots in my house that now seem to have become much worse recently. After giving up on configuring my extreme router to avoid issues I now want to extend the network.
If I put in a network cable from the extreme router to an airport express on the other side of the house can this be configured to be the same wireless network?
I know express routers have an option of extending the network is this for wired or wireless or both and if I do this will it show up as one wireless network with no interference issues?. At the moment I am planning on getting an express airport and using some of those power cable ethernet adapters to link the two routers up should this work okay?
Many thanks
Andy

Welcome to the discussions, Andy!
If I put in a network cable from the extreme router to an airport express on the other side of the house can this be configured to be the same wireless network?
Yes, post back if you need more details about this.
and if I do this will it show up as one wireless network with no interference issues?
There will be no interference issues between the AirPort Extreme and AirPort Express. However, if you live in an area with a number of other wireless networks around you, or you have cordless phones, there may well be some interference issues to tackle.
I am planning on getting an express airport and using some of those power cable ethernet adapters to link the two routers up
That should work assuming that both ethernet powerline adapters will be on the same master electrical circuit. I would suggest that you get a clear understanding of the store's return policy though...just in case.
Message was edited by: Bob Timmons

Is it possible to extend an Airport Extreme Network with a normal router ?

Hi everyone !
I know this question as been asked a lot before, but not in this way, I always saw : How to connect an Airport Extreme/Express to a Normal (D-Link, Linksys, Ect.) Router. What I wan't to do is connect a normal router to my existing Airport Extreme to extend the range of it. I know you can extend the network with an Airport Express, the thing is, i wan't to try with the router I replaced by the Airport Extreme. It's an D-Link DIR-615. If someone know how to do this it will be very nice and helpfull for me! I know on Apple website it says that it's not possible but some people seems to get it to work!
Thanks a lot !
(Sorry for my bad english i'm french Canadien)

You can extend the wireless range of the AirPort with a D-Link or the other way around ... BUT only if the connection between them is wired. This would be the basis of a roaming network. If you must have them interconnected by wireless, then it will NOT work.

How do I use an Airport Express as a "range-extender" for Airport Extreme?

I bought an Airport Express with the intent of using it as an "extender" for my Airport Extreme, but I find no paper that describes how this is done. Any suggestions would be appreciated.
Thanks and cheers, Veit

Thanks for the info. Try this to see if it will do the job for you:
_On your AirPort Extreme (AEBS):_
Open AirPort Utility and click Manual Setup
Click the *Wireless tab* below the row of icons
Your *Wireless Mode* should already be set to “Create a Wireless Network”
Make sure there is a check mark next to “Allow this network to be extended”
Note the setting for Wireless Security as you will need this for the next setup on the AirPort Express
Update to save changes
_On the AirPort Express (AX):_
Hold the reset button in on the AX until you see the amber light begin to blink more quickly
Temporarily, move the AX near your computer and connect a short ethernet cable from your computer to the AX
Open AirPort Utility and click Manual Setup.
Click the *Wireless tab* below the row of icons
*Wireless Mode*….should be set to “Extend a wireless network”. If you don’t see this choice, hold down the option key when you click on the selection box
Wireless Network Name…the name of your main AirPort Extreme network should appear as a choice. Click to select it.
Place a check mark next to Allow wireless clients
Wireless Security….exact same setting as your AEBS
Wireless Password…exact same password as your AEBS
Confirm Password
Click the Base Station tab to assign a name and device password for the AX, set time zone, etc.
Click the Music icon to enable AirTunes if you wish
Update to save settings. You can disconnect the ethernet cable and move the Express to the desired location.
For further reference, Apple's instructions for the "extend" setup appear on pages 43-44 in the Apple AirPort Networks Guide.
Please post back on your results.
Message was edited by: Bob Timmons

Extend network airport extreme

Similar Messages

Maybe you are looking for