Extend Range of Linksys WRE-54G using Airport Express?

I have a Linksys WRT-54G as my wireless router. I am currently extending its range across my house using a Linksys Range Extender WRE-54G. I want to connect a stereo and a PS3 in the basement to the network, using my Apple Airport Express.
When I configured the Airport Express as a simple range extender for the WRT-54G, it seems to crash?/interfere? with the WRE-54G, so neither the AE or the WRE work. If I unplug either the WRE or the AE, the other begins to operate again.
Any ideas what's wrong? What I can do to get it working as planned?
Thanks,
Michael

I use an airport express which connects to my airport extreme and extend my wifi that way would assume that an airport express connecting to another express would act likewise
not sure what you are asking it in the windows on mac forum though

Similar Messages

Extending range of Linksys WRT310N router with Airport Express 802.11n

I am trying to extend the range of an existing wireless network set up with a WRT310N router with an Airport Express 802.11n - I've tried choosing both "Participate in a WDS network" and "Extend a wireless network" and both have run into problems.
Any advice would be greatly appreciated!
Thanks, Amy

amysinsh, Welcome to the discussion area!
Sorry but this is not possible.
It would be possible if the wireless network was created by another AirPort Express (AX), anAirPort Extreme base station (AEBS), or a Time Capsule.

Extend Range of Belkin Wireless Router with Airport Express Base Station

I would like to know if I can extend the range of my Belkin N1 Wireless Router using the the Apple Airport Express Base Station?
If so, can someone help me to find out which settings/configuration I need to set of my Router and Airport Express in order the extend the range of my network.
Thank you in advance for your support.

DLink Xtreme wireless N cabled to the Time Capsule 1TB - Simultaneous dual-band Wi-Fi. In addition to extending wireless range, would this also allow me to connect cabled devices to the Airport? In essence, increasing the number of cable ports available on the network?
Connect an ethernet cable from one of the LAN <-> ports on the D-Link router to the WAN (circle icon) port on the Time Capsule.
Configure the Time Capsule as a "bridge" to use the exact same wireless network name, exact security and password as the D-Link router and you will in effect, have one large wireless network. Computers will be able to "roam" from one area to another and they will automatically connect to the router with the strongest signal.
The ethernet ports on the Time Capsule would be active and operate exactly the same as the LAN ports on the D-Link. Computers could plug into either router for an ethernet connection.
The toughest challenge in this type of configuration with routers from two different manufacturers is that they typically use different names for security types. If the security settings between the two routers do not match exactly, you won't have one network, you'll have two, each requiring a separate log on.
Check the configuration pages on the D-Link to see what type of security it is configured to use. Hopefully, it is +WPA2 Personal+, since that is the most compatible type of security among devices. Or +WPA/WPA2 Personal+ would work.
If the D-Link does not use this type of security, what is it using now? What are the other WPA associated settings that are available? We need to know this in order to provide you with the correct step by step configuration.
Post back with your questions and findings.

Extending g wireless from Time Capsule using Airport Express...

Hi,
My Time Machine is working well and I have two old Airport Express units that I'd like to use as wireless extenders.
The Airport Expresses are the older type (i.e. only do 'g' wireless) and, according to the AirPort utility, they can't see the Time Capsule. My iPhone can connect OK so the 'g' network must be working.
Am I doing something wrong? Can I use my Airport Expresses to do this?
Thanks!

Thanks for the info. Your iPhone is connecting to the Time Capsule, not either of the AirPort Express devices.
In order to configure the AirPort Express devices to extend the wireless network, your Time Capsule Wireless Mode would need to be set to "Participate in a WDS network". You probably did not see this choice because it is "hidden". Hold down the "option" key on your computer while you click on the selection box to see if it appears.
I'm not necessarily suggesting that you try the WDS setup. It's an older technology that places a heavy bandwidth penalty on your wireless network in return for greater wireless coverage. The first Airport Express that you configure will cut the bandwidth of your network in half. The second will cut the bandwidth in half again. In other words, you are down to 50% of the original bandwidth with the first Express and down to only 25% with the second.
If you are getting acceptable wireless performance with the Time Capsule now, I would be tempted to leave well enough alone until you could add an AirPort Express "n" version, which would allow you to use the "extend a wireless network" setting. This is a much better performing arrangement and much easier to configure.
The WDS configuration is quite complex and frankly difficult for many users. To get an idea of the process, read over pages 42-44 in the Designing AirPort Networks Guide.
If you want to try this anyway, you will need reconfigure your Time Capsule and both Express devices to work in the WDS setup.

How do I use airport express to extend my wireless network?

How vcan I extend the range of my wireless network using Airport Express?

It appears that you may have "join a wireless network" and "extend a wireless network" mixed up a bit.
The Express can "join" virtually any wireless network produced by any manufacturer's router if it is provided with the correct settings:
name of the wireless network
the correct wireless security settings
and correct password.
"Join" is normally used for AirTunes or to connect a USB printer to the Express for remote printing.
But, the Express does not provide any additional wirless coverage when it "joins" another wireless network.
Apple's "Extend a wireless network" feature, which was introduced about 5 years ago, allows the Express to connect to another Apple "n" wireless router and then "repeat" or "extend" the wireless signal....providing more wireless coverage in the area where the Express is located.
This is a proprietary setting. Apple says it will not work with devices from other manufacturers. To our knowledge, this is correct.
Prior to 2007, Apple used a setting called WDS to allow the Express to be configured to provide more wireless coverage. Attempts were made by a number of manufacturers to standardize the WDS settings, but things were never finalized.
The result is that Apple's older "b/g" routers were sometimes compatible with WDS settings from another manufacturer. There were a handful of products....5 or 6, as I recall....that were said to work. Some did, some didn't. Linksys had a couple of models, Netgear had one, SMC another, etc. Extremely limited.
Since WDS was never adopted as an industry standard, manufacturers developed their own WDS settings. Compatibility was extemely limited and unreliable. That continues to this day with WDS.
Bottom line....It is always best to stick with the same manufacturer throughout your network as far as routing is concerned.
If you have an newer "n" Apple router like an AirPort Extreme, the Express can extend the wireless as can along Extreme. If your Extreme is dual band, and you want to extend both bands, then you need another Extreme.
Another responder suggested to someone that they could connect the AirPort Express to a router via Ethernet. What exactly would that achieve?
That is a completely different subject since this discussion is about extending a wireless network using wireless only.

Do I have to use airport extreme to be a main network if I want to use Airport express extend my wifi range

Do I have to use airport extreme to be a main network if I want to use Airport express extend my wifi range.

You cannot extend wifi from a different brand router..
Only apple to apple.
But the apple router does not have to be the main router.. it can be in bridge.. as long as it is creating a wireless network it will work fine.

Can I use AirPort Express as booster/extender to LinkSys router signal?

I have LinkSys N router (which I got free, else would've bought AirPort), its signal isn't strong enough in office room. Can I use AirPort Express as a booster/extender? Some sources say Express can only talk to another Express, others say it can communicate with the LinkSys. Which is it? I don't want to spend the money for two Expresses unless I have no choice (very limited budget nowadays).
I've been hassling with this for over a month, and I'm extremely frustrated.
Thanks to anybody who can help me with this.

Most likely no. That is because most non-Apple router's implementation of WDS is not compatible ... and this is true the other way around. It is true that some early Linksys models, mainly the WRT-54 series were compatible, but I have not seen anything since then that is.

I have a linksys WRT54G router that we use as a base. I want to use Airplay using Airport Express and hook up my stereo to it. How can i set up my Airport express without a PC/laptop? I just downloaded Airport utility on my iphone and ipad,will that work?

I have a linksys WRT54G router that we use as a base. I want to use Airplay using Airport Express and hook up my stereo to it. How can i set up my Airport express without a PC/laptop? I just downloaded Airport utility on my iphone and ipad,will that work? And one more thing about the setup, the linksys router shich acts as a base is in a different room as the airport express which i wanted to use for airplay. So I'm hoping to hook up the Airport express via wireless signal. If i can set it up, can someone pls help me out by posting detailed instructions. Thanks so much!

The first message that AirPort Utility will display during the auto setup will be that the Express will be confgured to "extend" the network. When AirPort Utility analyzes the network further, and sees that the Express cannot "extend" the 3rd party network, the next message will indicate that the Express is being configured to "join" the wireless network.
Once the Express is configured, if you later go into AirPort Utility to check the settings under the Wireless tab, you will see that the Wireless Mode is indeed "Join a wireless network".

Using Airport Express to extend an existing wired/wireless Dlink network

Our network uses a Dlink router which must be located in the basement. Our home office Apple computers are wired, and the wireless Apple laptop is almost always used in the living room, directly above the Dlink, so no signal strength problems there. However, the wireless signal does not reach as far as the home office. It's only 20-25 feet away on the main floor, but for some reason, probably structural, the wireless signal doesn't penetrate.
Now I need to extend wireless access capability to the home office, so that I can use the iPod Touch in the office. I've read through a number of posts, and haven't found one that exactly matches this issue.
The information about joining an existing network has this sentence in it:
"Or you can use AirPort Express or AirPort Extreme to extend the range of an existing AirPort Extreme or AirPort Express network by creating a Wireless Distribution System (WDS)."
The existing network I have isn't an AX network. And it's both wired and wireless. And one of the detailed posts explained why a WDS was not the best way to go. Plus I'm confused by references to "base stations" which seem to refer to something that looks like a Time Capsule, not to an AX.
If AX will do what I want it to, I'm envisioning plugging it (all by its lonesome) in to a wall outlet in the hallway outside the home office. That's based both on what I want and what the salesperson said AX could do when I explained what was wanted.
The Dlink network has been working beautifully for months, and I don't want to do anything to screw it up! That includes even opening up the AX utility software until I know exactly what to do.
Can I do the setup (once it's explained!) on the wired computer? If I have to connect the AX to the network as part of the setup, can I use the 5-port switch that extends the wired connection the extra two feet to the computer (and also provides the wired network connection for the main printer)? Or should I take the laptop downstairs and connect the AX directly to the Dlink router?
Thanks,
Marg

+If I connected the AX by cable to my 5-port switch (which in turn is connected directly to the Dlink), would that constitute "an ethernet connection to the D-Link"? If so, then it should be possible to use it as described in your 6th paragraph, to "expand ... (our) main wireless network" -- is that right?+
Yes, this will work great.
+I'd never heard of ethernet powerline adapters, which sound very cool but are not wireless per se - you need a cable to connect the computer with at the far end, and it's wireless capability that I'm trying to create in the home office.+
Rather than hooking a computer up at one end, you could hook up the AirPort Express at one one and setup wireless that way. You won't need the adapters in this case since you have access to the switch. You may have need sometime in the future to get an ethernet signal to another part of the house, so keep this option in mind.
Here is how to setup the AirPort Express. You will use AirPort Utility, which should already be on your Mac Pro. Its located Hard Drive > Applications > Utilities.
Temporarily, connect the AirPort Express (AX) directly to your computer with a short ethernet cable to set it up. When you have the configuration done, you can disconnect the cable and move the AX to the location where it's needed.
Open AirPort Utility and click Manual Setup
Click the Base Station tab below the row of icons to enter a name and device password for the device and choose your time zone, etc.
Then click the AirPort icon in the row of icons at the top of the setup page.
Click the Wireless tab below the icons
Wireless Mode....Create a wireless netork
Wireless Network Name....Exact same name as your D-Link wireless network name
Radio Mode....802.11n (802.11b/g compatible)
Channel...Automatic (see note* at bottom)
Wireless Security...exact same setting as D-Link network
Wireless Password....exact same setting as D-Link network
Click the Internet icon in the row of icons
At the bottom of the page, make sure that the setting for Connection Sharing is set to "Off (Bridge Mode)". This setting allows the AX to work in tandem with the D-Link.
Update to save settings.
*Automatic will usually work well for this. Ideally, you want the D-Link and AX to be on channels that are least 5 channels apart. Automatic will usually choose an open channel, but you may need to manually set the channels on both routers for this step.
Your setup should work fine. Please post back on your progress or questions.

I used Airport Base station and I was able to extend my network using airport express and connect my printers. Now I am using Extreme and I can't extend the network (Express) or the printers nothing shows up. I am using utility 6.3 and Mt Lion What is

I had an Aiport Base Station and extended using Airport Express, where I also connected my printers (network). Now using Airport Extreme off Mt Lion 10.8.4 and Utility 6.3.
I can't extend the network (express) or connect my printers (USB) nor will it find my one wifi printer.
What's up?

For now, leave the AirPort Express powered off.
Power off the entire network....all devices.....in any order that you want
Wait a few minutes
Power up the modem first, and let it run 2-3 minutes by itself
Power up the AirPort Extreme next, and let it run a full minute
Keep powering up devices one at a time about a minute apart until everything is powered up (leave the Express off for now)
Open AirPort Utility and check to see if the AirPort Extreme is visible.
If it's not, click the AirPort Utility menu at the upper left of the screen, then click About AirPort Utility. Post back with the version number of AirPort Utility that you see there....which should be AirPort Utility 5.6.1.
Post back on your progress.

How do I extend an existing wireless network using airport express?

Hi all,
I am trying to extend existing wireless network using airport express, my main router is Belkin

Unfortunately, Apple's "extend" feature is designed to only work with other Apple routers if you are trying to "extend" using wireless only.
It is extremely unlikely that this feature would work with a router from another manufacturer using wireless only.

Model or serial number ranges for buying a used Airport Express?

Hi --
I am interested in buying a few used Airport Expresses. Is there a way to determine which generation or version a given Airport Express belongs to, e.g. by serial number range or model number?
Thanks,
Ramon

Basically there are only two versions of the AirPort Express: 802.11b/g (Model# A1084 / Part# M9470LL/A) & 802.11n (Model# A1264 / Part# MB321LL/A) Note: The Part#s provided are USA-specific.

Using airport express to extend network via ethernet socket

I have a wireless router set up which feeds my mac and tv (via a wired ethernet connection). I have also a pc which doesn't have wifi capability.
Can I use airport express to make my pc pick up the wifi by plugging the pc into the ethernet socket? I would also plug a printer (currently connected to the pc) into the usb, so it can become a shared printer.
Thanks

Can I use airport express to make my pc pick up the wifi by plugging the pc into the ethernet socket?
Yes. But, it is the AirPort Express that would "pick up the wifi". Then, you would connect an Ethernet cable from the AirPort Express to the PC.
Configure the AirPort Express to "Join a wireless network" and click the option to "Enable Ethernet clients" during the setup to activate the Ethernet port on the device.
I would also plug a printer (currently connected to the pc) into the usb, so it can become a shared printer.
There is a good chance that your printer will work connected this way, but you won't really know until you try.

Using AirPort express

How can i use AirPort express as a range extender via LAN cable with Belkin PlayMax router ?

thanks for the link. I remember when I last had this problem and got in touch with Apple and they said my airport express was out of range and suggested I buy another one Then it started ot work and did so for some time.Now I dont know whether this is at all relevant but a week ago hard started my Mac which necessitated me re setting the operating system software in the process i mistakenly erased all my volume so I am wondering whether that had anything to do with it. Thanks

How do I expand my Airport coverage using Airport express?

I want to expand the reach of my wifi network (i'm using Airport extreme). Can I do that using Airport Express? If yes how?

HI ldelage,
From AirPort Express frequently asked questions (FAQ):
Question: Can AirPort Express be used for a Wireless Distribution System (WDS)?
Answer: Yes. AirPort Express can be a WDS main, remote, or relay station. It can function as a WDS main whether or not you are using it as a router to share your Internet connection (NAT).
Wi-Fi base stations: Setting up and configuring a Wireless Distribution System (802.11b/g). Explains how to use the Airport Express to expand the Range of your wireless network.
The information your looking for is under "Instructions for using AirPort Utility 5.5.2 or later."
In this section, "Configuring a WDS main base station," explains how to configure your Airport Extreme so that it allows the Airport Express to extend your wireless network's range.
"Configuring a WDS relay base station," explains how to configure the Airport Express to be a relay for your Airport Extreme Base Station.
Both steps must be performed so that the express can extend the range of your wireless network.
-TT

Extend Range of Linksys WRE-54G using Airport Express?

Similar Messages

Maybe you are looking for