"extended network" error with airport express

i have my time capsule set up in my living room as the primary, and since there are several concrete walls in my house, i need to extend the wifi connection in order to get signal from my room which is located at the very end of my house. I've had my airport express placed near the doorway of my room which should be getting a clear signal from time capsule in the living room.
everything works fine for few days, and the blinking amber light started going off on the airport express. and from the airport utility it shows 1 notification on my airport express. It said an error of "extended network", if i choose to ignore it, the indication light turns back to green, but then i wont be able to connect to the internet.
is there some kind of settings need to be adjusted? please help~~~
my settings on airport express:
Router Mode: Off (Bridge Mode)
Connect using: DHCP
Configure IPv6: Link-Local Only

i've tried to plug the airport express literally right next to the time capsule, and it still showing the "extended network" error message. so it can't be the signal strength issue.
Help please....
additonal info:
my time capsule (primary) :
Connect Using - DHCP
Router Mode: DHCP and NAT
DHCP Range: 10.0.1.2 to 10.0.1.200
my airport express (extension) :
Connect Using - DHCP
IPv4 Address: 10.0.1.10
Router Address: 10.0.1.1
DNS Servers: 10.0.1.1
Router Mode: Off (Bridge Mode)

Similar Messages

Is it possible to expand networking capability with Airport Express?

I have 754S Sierra Mobile Hotspot, is it possible to expand networking capability with Airport Express?
Thanks,
Napat

No. The iPad can connect to only one WiFi system at a time.

When adding WRE54G to wireless network incompatible with Airport Express

I added a Linksys WRE54G to expand my network to a Powerbook G4 laptop with a weak signal. When I connect the wireless expander, I no longer see the Airport express in the airport utility. I cannot access the printer or itunes speakers attached to the airport express. When I power off the expander and have a weaker signal, the airport express is available again. I don't know how to configure the wireless expander to work with airport express, and if I try to create a WDS network with the airport express (currently unsuccessful), then I believe I will lose itunes support (and maybe the printer?).
Does anyone know how to configure the WRE54G so that I can still see the airport express on my network?
Thanks,
Brigitte

I was having the same problems. Try this link, someone seems to have solved it.
http://discussions.apple.com/thread.jspa?threadID=1271648

How do I extend my WiFi with Airport Express? I have Ethernet in the house and an Wifi that do not cover the whole house. I do not get it to work.

I have Ethernet in the house and an Wifi that do not cover the whole house. I do not get it to work. I have tried to get it into my network and it get connected via the WiFi but not the Ethernet. Also when it gives a green light I cannot see that it is giving any signals to my devices (iPhone etc).

You need to pay attention to something, while extending your network with the latest AirPort Express upgrade, your devices will be connected to it except your iPhone, you'll see your iPhone always connected to the capsule instead, even if you're at 1 foot from the AirPort Express.
You need to change the radio settings from automatic to 802.11a - 802.11b/g on your capsule, then I put it back to the default settings...
Now in the AirPort utility you should see your iPhone connected to the AirPort

Extend wireless range with Airport Express?

Hi,
I am using a Time Warner internet wifi router and need to extend the range in my home. Can anyone help me with how to extend the range using an Airport Express?
Thanks
Chris

Chris, are you planning to connect the AirPort Express to the Time Warner router using a wired Ethernet connection?
The reason we ask is that Apple's "extend a wireless network" feature to provide more wireless coverage....using wireless only.....works only with other Apple routers as far as we know.
It is almost certainly not compatible with devices from other manufacturers.

Airplay error with airport express and apple tv

I receive this message "An unknown error (-15006) occurred while connecting to the AirPlay device" when trying to play audio from iTunes on Macbook Pro to my airport express and/or apple tv. Both airport express and apple tv work fine with my iphone and ipad as well as streaming video from itunes library to apple tv from the Macbook. I have tried the previously posted solutions, but nothing has worked yet.

http://www.cultofmac.com/178460/the-real-reason-why-macs-before-2011-cant-use-ai rplay-mirroring-in-mountain-lion-feature/

Auto Network reconnect with Airport Express - tried all solutions so far

My G4 quicksilver will not auto network reconnect after sleep, or after turning Airport off and on again.
* I tried deleting and re-issuing a new LOCATION and new WPA mentioned at:
http://discussions.apple.com/thread.jspa?threadID=121824&tstart=150
* I also tried deleting network and airport preferences.
* I also made sure that I have the "distribute IP addesses" unchecked.
I still need to manually reconnect!
It used to work and show a nice scrolling network name when it found my network. After messing around with the AE configuration for another unrelated reason, this problem came up... OSX-4.2, without any change in months...
Help?

I have an iBook & an iMac on an Airport Express Network with WPA2 password security. Both are running OS 10.4.3, & are current with all security updates etc.
I set up both computers according to the suggestions of "Topic: Tiger and Lost Wireless Network Connectivity" by Duane, Henry B, iFelix, Alan Macdougal, & Dr Smoke. I created New Locations for each computer.
The iBook, now auto-connects just fine, but for the life of me, I can't get it to work on the iMac. The iMac is 3 feet from my Airport Express; the iBook is downstairs. What do I try next?
Kenmackay
1.25 GHz Power Mac G4; 1.33 GHz G4 iBook Mac OS X (10.4.3)
1.25 GHz Power Mac G4; 1.33 GHz G4 iBook Mac OS X (10.4.2)

What range extender is compatible with Airport Express?

I want to extend the range of my wireless signal. I have two airport expresses, one is connected in the office (to the cable modem). The other one is in my bedroom and is used as an extender. I want to extend the my wireless signal to my kitchen, I get the signal from the office but it's weak. However, I don't want to spend the money on another airport express. So, what range extender can I use, or what other ideas are out there.
PowerBook G4 Mac OS X (10.4.6)

If you want to this wirelessly then you will need to use another Airport Express.
If you can run a cable to close to the kitchen from the office and attach a cheap wireless access point then you can create a roaming network.
iFelix

How to extend wireless range with airport express

I am using 10.6.8....I have a wireless connection and would like to use an airport express to extend my range....the unit model is A1084. I can't find out how to do this in assistant. Does anyone know?

An Airport can extend only another Airport WiFi. It can not extend non-Apple WiFi systems.
I don't know the model numbers and I don't know when the extend capability was added.

Extending network with Airport Express and Airport Extreme (latest models) causes chaos on network

Today I upgraded from my several year old Airport Extreme (3rd gen) and 2nd gen Airport Express to a new (what you'd buy on the shelf today) Airport Extreme and Airport Express. All airports are updated with the latest firmware and I'm using windows 7 for configuration.
The intention is to use the Airport Extreme as the main router, also serving wifi. And extend the network using the express. As such, the following has been done:
The Airport Extreme is configured for automatic channel, and automatic radio mode. I tried to select 802.11n 5 ghz and 802.11 n 2.4 ghz only, but it won't take the changes. Additionally, it wont' accept me using only channel 6. Not sure why, but I digress. The airport extreme is not set to broadcast a separate name for the 5ghz network.
The Airport Express is configured to use bridge mode, use an existing wireless network and is connected to my network on it's WAN port (the circle icon on the back) with ethernet. The password and wireless name used in configuration is the same as created initially on the Airport Extreme.
Initially I did the configuration of both airports on my computer, connected by ethernet to ensure stable connectivity while I inputted settings. During this, they appeared to accept the changes fine. However, when I moved the airport express to it's destination (other side of my house), the entire network went crazy.
Internet became slow, and often wouldn't load pages. This was on wired and wireless connections. When I attempted to administer the Airport in the Utility, they would not load, an error would occur. Also, at one point the Airport Extreme had renamed it self with a (2) at the end. Which was super odd. So far, the only solution has been to unplug the Airport Express and attempt to devise a solution.
Anyone have any ideas? Of course, I will continue to tinker with this, but it seems realllly strange. The previous setup was also extended (granted, using wireless only, not ethernet > wireless) and worked fine, granted it was a smidge slow, but it worked.

I wanted to add this.. I followed the guide here: http://support.apple.com/kb/HT4260 to extend using ethernet, and the above is the result.
I just tried re configuring in OS X Mavericks and got the same, odd, result.

How do i use my time capsule and extend the network with airport express

I have a new iMac and Time Capsule, how do i extend the network with airport express. My time capsule does have a guest net work, and logins and passwords? I am no computer person. So for me it would have to be spelled out.

Use the search as this has been done to death ..
Bob Timmons is the expert on this.. look at his answers here.
https://discussions.apple.com/thread/4274187?start=0&tstart=0
https://discussions.apple.com/message/21856077#21856077
This has been automated in the v6 utility. I am used to doing it manually in v5 utility which is also fairly easy.
Apple doco is also good to read.
http://support.apple.com/kb/HT4145
http://support.apple.com/kb/HT4259
Note.
You cannot extend the guest network unless everything is up to date 7.6.3 firmware. And that is only with the TC as the main router in the network.
All apple routers can be configured as the main wireless or as the extend wireless.. so don't worry if a post uses express or extreme or TC.. they are for wireless, the same thing.

Extend wireless network with AirPort Express

How to extend the wireless network with AirPort Express and Belkin PlayMax as the primary router ?

How it work if I have an AirPor Station and 4 Airport Express, I actually also have an old TimeCapsule and an old AirPort Express. Can I cover all my house (around 300 m2). And will the old Airport slow down or convict with the new ones?

How do I extend my wifi using Airport express with my time capsul?

I want to extend my wifi from my time capsul. Can I do this with airport express? I have my wifi with cable so would I need to get another modem and hook the express to that? Would that help? I want to keep the same network and not add another.

You need to pay attention to something, while extending your network with the latest AirPort Express upgrade, your devices will be connected to it except your iPhone, you'll see your iPhone always connected to the capsule instead, even if you're at 1 foot from the AirPort Express.
You need to change the radio settings from automatic to 802.11a - 802.11b/g on your capsule, then I put it back to the default settings...
Now in the AirPort utility you should see your iPhone connected to the AirPort

Problems when trying to expand network with airport express 1st generation

Hi, I have an airport express 1st generation that never actually worked, so I lent it to a friend. Now I try to install it, in Order to expand my already existing network. Whilst airport express is trying to connect to the existing network, the airport utility programme tells me that suddenly there is no response by the airport express. When I then try to restart it, there is no sign of connection at all. I tried to download an updated version of the firmware but thats not possible since I can't get a connection to the network. Any suggestions??!
Many thanks in advance, Dominic

A first generation AirPort Express cannot be used to "wirelessly extend" a network without resorting to configuring a WDS, a horribly inefficient compromise. Furthermore, you will need an older version of AirPort Utility to administer it from a current production MacBook Pro.
Read this post for instructions: How to Configure an old AirPort Express
You can use it as an additional access point in a "Roaming network". To do that requires that you connect it to your primary router with an Ethernet cable. That would be its most effective use. This KB article provides instructions: Wi-Fi base stations: Setting up and configuring a roaming network (802.11 a/b/g/n)

Extending a time capsule with airport express twice

Hi,
I have been trying to extend my existing wireless network recently but it never ended up how I wished...
I have one 4th generation Time Capsule (A1409) and two Airport Express 802.11n (1st generation A1264).
All currently have MAC Address base authentication and no security in place for was of testing (security not relevant at this point in time).
When I extend my Time Capsule with either Airport Express this works like a charm, the LEDs are all green and connection works for client devices.
When I extend my Time Capsule with both Airport Express the same applies, everything works.
However what I have found not to works it extending my Time Capsule with one Airport Express and then extending this Airport Express with the second Airport Express. While all LEDs are green and the second Airport is seen in the Airport Utility, I find no client are ever able to connect to it and alway either connect to the first Airport Express or to the Time Capsule. This is an issue I the area I want to cover is pretty big and I need the second Airport Express for the additional reach.
I haven't found anything against this setup, it however appears you can't connect to the second Airport. The Airport Utility would even accurately depict the situation with Airport Express one dotted line to Time Capsule, and Airport Express two dotted line to Airport Express one.
However no connection seam possible to Airport Express two.
I have swapped Airport Express one and two, and in this case Airport Express gets the clients and Airport Express one now extending Airport Express two gets none.
Is this an expected behavior, i.e. should I give up or is there anything I can do about this ?

However what I have found not to works it extending my Time Capsule with one Airport Express and then extending this Airport Express with the second Airport Express.
Apple's "extend a wireless network" feature will only allow you to extend the signal one level, not two. It's possible to have more than one device extending the signal, but each extender must connect directly to the main base station.....not to another device that is already extending the signal.
The Airport Utility would even accurately depict the situation with Airport Express one dotted line to Time Capsule, and Airport Express two dotted line to Airport Express one.
This is an illusion. AirPort Express is "joining" the wireless network.....not extending it. When the Express "joins" a network, it can be used for AirPlay, or a remote printer could be connected to the USB port, but the Express will not provide any additional wireless signal coverage when it joins a network.
Is this an expected behavior
Yes. I can try to look up Apple's support document that explains this if you want more information, but you may likely already have all the information that you need. Let us know.

"extended network" error with airport express

Similar Messages

Maybe you are looking for