Extended wifi via ethernet

Hello,
I have connected a new airport extreme via ethernet cable to my Airport / time capsule. The utility walked me through the process  ( extending my wifi to the other en of the home ).
The utility shows both units connected and the base station connected to the internet.. green indicator on all.
My Questions..
1. will the new ne extreme show as a new wifi on my devices to connect to or it just extends the range and my devices will use this automatically ?
2.how can I see if they are connectiing to the extended range if the automatically connect to it ?
3. can I check the signal strength ?
Thank you in advance

1. When you setup the roaming network.. you must create a wireless network on your new Extreme.. it can be the same wireless name (SSID) as the TC.. or different.. that is entirely your choice. Mostly people use the same name so it is roaming.. if you use different names it will not roam.
Roaming also requires same security setup and passwords.
2. The actual unit is shown by BSSID in the wireless on the computer Hold Option key and click the wireless fan.. (on iOS I am not sure but it should show BSSID).
This is the actual MAC address of the wireless.
3. The same screen shows link speed and RSSI which is signal strength.
You can also run the Wireless Diagnostics which is down the bottom of the same options screen. 
Read how to use wireless diagnostics.
About Wireless Diagnostics - Apple Support

Similar Messages

  • HT4259 how to configure extended network via ethernet

    how to configure an extended network via ethernet

    I assume that the Express is new, so that it still has the factory default settings.
    Connect an Ethernet cable from one of the LAN <-> ports on the AirPort Extreme to the WAN "O" port on the AirPort Express
    Power up the Extreme and Express if they are not already powered up
    Open Macintosh HD > Applications > Utiltities > AirPort Utility
    Click on the tab in the upper left hand corner of the window that reads Other AirPort Base Stations (1)
    Click on the AirPort Express xxxxxx
    Wait a minute or two while AirPort Utility analyzes the network and then announces that the Express will be configured to extend your network
    Enter a name for the AirPort Express and click Next
    Wait 2-3 minutes while AirPort Utility configures the Express and the Express restarts
    When you see the message that setup is complete, click Done
    That's it.

  • Cannot connect devices using Extend Network via Ethernet

    Hi
    I have been going nuts with this issue, and cannot seem to find any solutions. PLEASE HELP!
    I have an Airport Extreme (pretty new and all up to date) connected to my modem. Everything works perfectly. The wi-fi is great, all devices can connect without any issues so nothing is wrong here. The Airport extreme is dishing out the IP addresses etc. The Airport extreme is in the lounge.
    I purchased a new airport express yesterday. I put it in my study, far away from the lounge. I connected the airport extreme to the airport express using an ethernet cable. I plugged it in, and set it up to extend the wireless network via ethernet. I.e. it is set up in bridged mode and set up to 'create a wireless network' with identical name password etc. Everything is good. It reboots and the light is green. in the Airport utility everything shows up correctly.
    Here is the problem., The second that any device (lets say iphone) moves from the lounge to the study, and tries to 'jump' to the stronger network provided by the express, it kills the ENTIRE network. The following happens:
    1. The iphone loses wi-fi signal immediately. If I go into wi-fi settings, it sees my netwrok with FULL strength, but just remains in the 'spinning ball' state trying to connect. Seems to me that the express is unable to hand out an IP address or something.
    2. If i open the airport utility on my Imac (in the study), the airport extreme has a yellow warning light and cannot be found via ethernet OR wi-fi. (The Imac is also Hard Wired from the Airport extreme in the lounge).
    THe whole system requires a re-boot in order to work again.
    If I re-boot the system, and leave a device near the airport express, it immediately receives signal, gets an IP address, and has an internet connection. Going back to the lounge causes no issues, it doesnt drop signal and still connects to the internet via the extreme. But as soon as I walk back into the study again - BOOM, everything drops.
    I only purchased the new express because i was having EXACTLY the same issue with an older Airport extreme. No matter what I do, it just wont work via ethernet. I have tried all manner of settings. The ONLY setting that seems to work is to extend the wi-fi network. However, the rooms are too far apart, and this will require a third station in the middle, which i want to avoid (by the time the wifi network is extended across 3 decvices it is too slow).

    Can I use airport express to make my pc pick up the wifi by plugging the pc into the ethernet socket?
    Yes. But, it is the AirPort Express that would "pick up the wifi". Then, you would connect an Ethernet cable from the AirPort Express to the PC.
    Configure the AirPort Express to "Join a wireless network" and click the option to "Enable Ethernet clients" during the setup to activate the Ethernet port on the device.
    I would also plug a printer (currently connected to the pc) into the usb, so it can become a shared printer.
    There is a good chance that your printer will work connected this way, but you won't really know until you try.

  • Airport express won't extend network via ethernet but shows GREEN (HELP!!)

    I have the following routers setup up the same network and are working.
    10.0.1.1 Airport Extreme (connected to hardline from IP)
    10.0.1.2 Time Capsule 1 (extending network and providing internet connection to computer via ethernet)
    10.0.1.3 Time Capsule 2 (extending network and providing internet connection to Xbox1)
    10.0.1.4 Airport Express 1 (extending network and providing internet connection to Xbox2)
    Not working correctly
    10.0.1.43 Airport Express 2 (wanting to set this router up to extend network to plug into desktop)
    The router seems to join the network fine and will show GREEN but doesn't show a similar IP address as the rest of the routers. It also doesn't provide any internet connection via ethernet to any computer, the network pref page says that it shows RED and that nothing is connected to the computer for internet but airport shows GREEN.
    Reset the router multiple times, tried every which way of setting it up and no go. I also tried assigning it a IP and not using DHCP and gave it a 10.0.1.5 and still the same outcome.
    Right now just at complete loss as to what to try next.

    Sorry, the older version of the Express does not have the option to  "extend a wireless network", which is the setting on the new Express that provides more wireless coverage and also enables the Ethernet port.
    What you want to do can be done with a different setting..."participate in a WDS network" on both the Time Capsule and Express, but I am not recommending that you do this because WDS operates only in "g" wireless mode. Your Time Capsule would lose most of its performance in this setting and the network would slow down tremendously...defintely not what you want for gaming.
    You'll have the best performance if you connect the PS3 directly to one of the Ethernet ports on the Time Capsule using an Ethernet cable. If it is not possible to run the cable, the next best performance option would be to use a pair of Ethernet powerline adapters to send the Ethernet signal over the existing AC wiring in your home.

  • Trying to extend network via ethernet

    Trying to add another Extreme to our network to assist with the number of wireless clients on our existing Extreme.  Trying to add the 2nd Extreme via Ethernet and extend the same network SSID and all other info.
    After setting up and adding it shows that it is extending via wireless, and when connecting to the WAN or LAN ports it wants to take the entire network down.
    Using 5th Gen Extreme.  Airport Utility 6.2, and all devices have 7.6.3 firmware.  Already have 2 Express units on the system extending the network wirelessly where we do not have Ethernet ran.  Those have been working for over a year.
    Any thoughts on what we are missing when setting this up where we can't plug another Extreme in via Ethernet?  In the setup I don't see an option for extending via ethernet.....

    Close AirPort Utility if it is open
    Disconnect the Ethernet cable to the new AirPort Extreme
    Hold in the reset button on the back of the  AirPort Extreme for 7-8 seconds and release. Allow a full minute for the AirPort to restart
    Make sure that the Ethernet cable is connecting from a LAN <-> port on the "main" router to the WAN "O" port on the new AirPort
    Click the AirPort icon at the top of the Mac's screen and wait a minute for the heading of New AirPort Base Station to appear
    Just below that, click on the AirPort (an AirPort Express is pictured in the example)
    AirPort Setup will open automatically and take a minute to analyze the network....then announce that the AirPort Extreme will be configured to "extend" your current network.
    Enter a device name for the AirPort Extreme and click Next
    AirPort Setup will take a minute to configure everything for you. When you see the message of Setup Complete, click Done
    Test the network and report on your results

  • Use Airport Express Brick N to extend network via ethernet

    I have the old brick-style Airport Express N model, which I'm currently using to extend the newer Airport Express hockey puck. The hockey puck is setup to with DHCP and creating the network. The brick is in setup to extend the network using DHCP and in Bridge Mode. When I plugin the Ethernet cable from the Ethernet port of the hockey puck to the brick, I lose all internet connectivity. I seem to recall reading some documentation that said the brick would support ethernet rather than just over-the-air. Thanks for your help!

    My question is: can I connect the two via ethernet cable to the extending is happening over the air? I'm not sure the brick is capable of this?
    It is possible to "extend" in two different ways:
    1) Extend using a wireless connection between the AirPorts. Apple calls this "extend using wireless" during the setup. When you extend this way, about half of the potential speed on the network is lost.
    2) Extend using a wired Ethernet connection between the AirPorts. Apple calls this "extend using Ethernet" during the setup. When you extend this way, full bandwidth on the network is maintained since there is no signal loss in a wire.
    If you want to "extend using Ethernet", the 2nd Gen AirPort Express must be the "main" router, so you will need to reconfigure it for that purpose. The 1st Gen will also need to be reset back to default settings and reconfigured as well.
    Once the 2nd Gen Express is working correctly as the main router, connect an Ethernet cable from the LAN <--> port on the 2nd Gen Express to the Ethernet port on the 1st Gen Express and use AirPort Utility for the setup.

  • Using Time Capsule to Wirelessly Receive Internet and then Extend Network via Ethernet

    Hello,
    Our modem/router combo is located downstairs, and my computer that i want to get online is upstairs. I cannot get a ethernet from the modem to my computer to access the internet, so I wanted to try to use my Time Capsule to help me get online upstairs (not sure if this is possible...)
    My idea was to have the Time Capsule receive the wireless signal and then connect the computer to the Time Capsule through an ethernet so that I may get the computer online. Essentially wireless connection in, wired connection out.
    I've been playing around with the device for a while now, and can't seem to make this work. Has anyone used the Time Capsule in this fashion? Is it even possible? If not, does anyone have any suggestions on how to get my computer online?
    Thank you very much for any help/input!!

    Why not try a pair of these over domestic power loop.
    http://www.netgear.com/home/products/powerline-and-coax/high-performance/XAVB510 1.aspx#two
    Not cheap though Best buy link
    http://www.bestbuy.com/site/NETGEAR+-+Powerline+Ethernet+Adapter+Kit/5042106.p?i d=1218603011817&skuId=5042106
    The Apple solution might well need Two devices to extend range.
    You would retain your ISP router/modem however would go into settings and TURN OFF wireless on that device - you can do this in the Java Web based control panels on most routers.
    Now you sling the Ethernet cable between that router and a purchased Time Capsule device locally and set this up to create a new local Wifi network (Replacing that of the ISP supplied router) . Being a dual band device and being able to broadcast both over 2.4 Ghz and 5 Ghz frequency base bands simultaneously you could well see improved performance and range straight away.
    However if not then you are going to need a further device an Airport Express set up in bridged mode somewhere between the Time Capsule and your upstairs rooms. Your may have to try various power points and locations to get coverage required.
    Further Airport Express devices can be added in bridged mode as required to cover blind spots, however remember each additional device degrades the overall network performance somewhat.
    Again this will get quite costly.

  • Using airport express to extend network via ethernet socket

    I have a wireless router set up which feeds my mac and tv (via a wired ethernet connection).  I have also a pc which doesn't have wifi capability.
    Can I use airport express to make my pc pick up the wifi by plugging the pc into the ethernet socket?  I would also plug a printer (currently connected to the pc) into the usb, so it can become a shared printer.
    Thanks

    Can I use airport express to make my pc pick up the wifi by plugging the pc into the ethernet socket?
    Yes. But, it is the AirPort Express that would "pick up the wifi". Then, you would connect an Ethernet cable from the AirPort Express to the PC.
    Configure the AirPort Express to "Join a wireless network" and click the option to "Enable Ethernet clients" during the setup to activate the Ethernet port on the device.
    I would also plug a printer (currently connected to the pc) into the usb, so it can become a shared printer.
    There is a good chance that your printer will work connected this way, but you won't really know until you try.

  • How to configure extended network via ethernet

    i have a airport extreme and i need to connect my airport express using ethernet cable.
    what should be the configs in the airport extreme to get this done?
    thank you.
    mauro

    Please answer my questions on your other post so that we can help.

  • Airport Extreme with Airport Express for extending WiFi Network...

    I have had an iMac for quite a few years now and never needed WiFi until this week. I purchased a Macbook Air, an Airport Extreme and an Airport Express over the last 24 hrs. I opened the Airport Extreme first and followed the somewhat easy installation procedures. My iMac is wired via Ethernet cable to my Airport Extreme. The Airport Extreme is connected to a Motorola Cable Modem using Time-Warner. I also happen to have a Verizon Network Extender connected via Ethernet cable to the Airport Extreme. The spot where I most frequently would be using the Macbook Air, is about as far away from my iMac and Airport Extreme Base Network Router as you could be. The WiFi works, shows only one bar on the Airport icon. Consequently I want to plug my Airport Express in near this location to give me a better WiFi signal (and thus perhaps faster performance). I have read both the Airport Express Manual and the Airport Extreme Manual but neither talks all that much about the network extension function with the exception of connecting a stereo to an existing WiFi network. I am wondering what the specific steps are to add the Airport Express as a Network Extender. I also wonder if my Macbook Air will be able to access my iMac as the iMac is connected via Ethernet to the Airport Extreme vs. using the Airport Network. Any help will be most appreciated.

    Julie Kruyne wrote:
    I am trying to do the exact same thing and am having some difficulties.
    It was easier for "WiseJD" because he was using two Apple base stations, instead of your AT&T router.
    I select Manual Setup, it just sits there thinking - I can't get into the actual set up.
    So you see the Express in AirPort Utility, but when you select it and select "Manual Setup", nothing happens?
    When setting up the Express to extend my existing wireless network (AT&T 2WIRE modem and Airport Extreme), do I initially connect the Express, via Ethernet cable, to the modem or the Extreme?
    I'll guess that the AT&T device is connected to your broadband connection. Is the 2WIRE device either without Wi-Fi support or is that turned off? How is the Extreme configured, in particular in the AirPort/Wireless panel "Wireless Mode" setting and in the Internet/Internet Connection panel, "Connection Sharing" setting?
    If anyone could provide a step by step process on exactly how to set up the Express to extend my existing network, I would be grateful.
    I have very little experience with mixed-vendor home networking, but someone should be able to help.

  • HT4262 Is there any way to extend my Apple Extreme Base Station using an Apple Express by via ethernet or does it only work via wifi and being in range?

    From what I read, the only way to extend my Apple Wifi Network is via another Apple Airport Extreme or Express using overlapping wifi zones. If I try to connect my Apple Express to my Apple Extreme via Ethernet, then this is guaranteed to fail regardless of how I configure the Express. Is that correct?

    It is certainly possible and better....in terms of performance.....to connect the AiPort Express to your AirPort Extreme using Ethernet to extend the network that way.
    If you are having problems with this, then your setup is not correct....or....if your setup is correct, you may have a defective AirPort.
    We can walk you through the steps to get things set up correctly if we can get some basic information to provide the correct settings.
    What is the model number of the AirPort Extreme?
    What is the model number of the AirPort Express?
    if you are not sure, look on the bottom of the Extreme and side or bottom of the Expess. The model number starts with an "A" followed by four numbers.
    We also need to know what operating system you are using on your computer. If you have a Mac, click the Apple icon in the upper left corner of the screen, then click About This Mac and post back with the OS X Version number that you see there.
    We will likely have more questions about your current setup to understand things a bit better, so please be patient.

  • Can multiple Airport Expresses be connected via ethernet to an Airport Extreme to extend a single WiFi Network?

    I am a big fan of both the Airport Extreme and Airport Express.  In my work environment, I need to create a good quality single wireless network around 2 large aircraft hangars and some offices at the perimeters.  We have a good quality wired Cat5e ethernet network extended between the buildings and offices now.  Is this possible and does it seem like a good practical solution?  I think that 4 or 5 Airport expresses would easily provide good wireless coverage in the needed areas. 

    Can multiple AirPort Expresses be connected via ethernet to an AirPort Extreme to extend a single WiFi Network?
    Yes, this will work just fine as long as any individual Ethernet cable run will not exceed much over 330 feet or about 100 meters.

  • Connecting via ethernet ports on an AEBS that is extending a wifi network

    I tried to get this out on the subject heading (trust me guys I searched the forums first but I couldn't quite find this issue)...
    I have a Airport Express connected via ethernet to a network. I am trying to use an AEBS to capture that connection and then share it via ethernet ports (LAN?) to a PC that has no wifi card.
    I setup the AEBS to extend the existing airport express wifi and that worked fine and I can connect to it fine via wifi on my laptop. But the pc that is plugged into the AEBS via ethernet is not able to connect.
    Thoughts?

    In order to enable the Ethernet ports on the 4G Extreme for the Mac Pro, both AirPorts need to be configured for an extended network. Please read through the steps provided in the link to see if you may have missed any steps.

  • I have a mid-2010 iMac and just purchased a 2TB TC, can't join existing wireless network with AC standard so attached to iMac via ethernet with TC wifi turned off.  How do i access TC now? not showing up in disk utility or on desktop. working fine with TM

    I have a mid-2010 iMac and just purchased a 2TB TC, I just found out that it can't join existing wireless network with new AC standard so attached to iMac via ethernet with TC's wifi turned off.  How do i access TC now? not showing up in disk utility or on desktop. It is working fine with TM.  My cheeper seagate drives etc kept crashing, so i didnt trust cheeper back up options anymore.  Connected those drives to TM via firewire and could see the drives and access them.
    Also, I didn't want to bridge TC with my new fios router that I paid 100 dollars for, to get N speed and also paying 10 dollars more a month for fast speed.  I heard that bridging slows down everything and then there can be port issues with mail etc.  I connect to the internet via airport only and it is pretty fast. Getting over 50mbs downloads and over 30mbs uploads.  Plus everything in my home it connected to my fios router, airport express for music streaming, two apple tvs, vuezone camer system.  I really didn't want to monkey around too much with my system.  But are there other options to connect the new TC.  Can't find info anywhere for this and called apple who gave me the info above.  after hanging up, i see that i cant access my TC and I am wondering if i would have to reset it to turn wifi on again to make changes to the drive, turn off blinking light  or repair it in disk utility if it should become corrupted.
    For other with similar issues i did solve some other problems: when i connected it to my ethernet port on my iMac wifi stopped working.  Found that I had to turn off the ethernet in the system>network screen, but then TM didn't see the TC so i restarted after changes and then it saw it.
    Now a rant.  I can't believe in this wireless age that Apple would make a product that cant join a wireless net work.  The apple rep said i could return it and look for the previous TC that would join an existing wireless network.  Are we going backwards?
    Thanks!
    lennydas

    Ok... it is getting a bit clearer but there are still some questions.
    I connect to the internet via airport only and it is pretty fast.
    I was assuming airport in this statement in your first post meant the TC or the Express.. but I now realise we are still in the mass confusion stage where apple calls everything wireless an airport. So what you mean is the airport internal card of the computer??
    Also, I didn't want to bridge TC with my new fios router that I paid 100 dollars for, to get N speed and also paying 10 dollars more a month for fast speed.  I heard that bridging slows down everything and then there can be port issues with mail etc.
    I think this is mistaken.
    Putting the TC in bridge mode plugged into your FIOS will not slow the network.. nor will it cause mail or port issues.. in bridge the TC is just a fancy WAP and switch plus the network hard drive.
    If the computer is close it will be faster than the FIOS.
    You can run both wireless networks with different names.. so it is clear which is which. But you can also setup roaming so the computers themselves pick which is the best wireless.
    I tried extending the wireless net work and tried joining wireless network, but the TC kept crashing and I had to keep resetting the TC.  the Apple support person said these, extend wireless network and joint wireless network, are no longer a connection option with the new TC because of the new AC protocol.
    Thanks again!
    You cannot extend to a non-apple wireless router.
    You cannot use join a wireless network because when you do the ethernet ports will be cut off.
    But that has not changed.. I don't think Apple support is correct.. there has been no change with the AC model.. it is simply a fact that apple routers do not work in join wireless mode other than as a dumb client. The same applies to AC as to the earlier version.. but I have asked another person to check this.
    Join in the express is the only apple router that still allows an ethernet connection.
    For now you best use of the TC is bridged to the FIOS. Wireless you can sort out between several options.

  • I'd like to alter my Airport Extreme/Airport Express wireless network so that the 3 Expresses connect to the Extreme via Ethernet. I've been told this will create a more stable wifi signal. How do I configure this using Airport Utility? Thanks.

    I currently have an Airport Extreme Base Station connected to my DSL router by Ethernet. Because I have a long, sprawling home, I have 3 Airport Expresses configured to "Extend the Wireless Network" I've established. Because of my home environment--thick walls encompassaing wire mesh, sprawling rooms, etc., it is hard to maintain a continuously-strong, stable WiFi signal. I've been told that I can create a much more stable network by connecting the Express units to the AEBS via Ethernet cable. Since my home is already wired for Ethernet, I'm considering making this change. If I proceed to establish the Ethernet connections, how do I then set up Airport Utility to accomodate this switch from a Wireless-based WiFi network to an Ethernet-based WiFi network?
    Thanks in advance for any help.
    Phyllis

    I don't see anyplace in the Utility to designate HOW the Express units are connected, only how they relate on the network to the Extreme,
    As I mentioned in the previous post, when you click the Internet icon in AirPort Utility:
    Connect Using = Ethernet  (This tells each Express to connect to the Extreme using the ethernet connection)
    Connection Sharing = Off (Bridge Mode)  (This setting allows your AirPort Extreme to function as the "main" router on the network, as it must for the setup to work correctly.
    You do not need to configure anything differently on the AirPort Extreme (as long as it is working correctly now) to connect the AirPort Express devices.
    The only other question I have is the following: I'm currently already using one of the Ethernet ports on the back of the Extreme-- for my husband's iMac. I really don't think he gains much in performance over how the iMac would run through wifi, so I could disconnect the iMac. If you think the iMac would do better to stay on the Ethernet connection, should I use a switch/splitter to add an extra connection?
    Since each AirPort Express must connect using ethernet, you will need to use the 3 LAN <-> ports on the AirPort Extreme for the AirPort Express devices.
    I would suggest that you try connecting the iMac using wireless to see if that will work. If the wireless connection is not satisfactory, then you can add a 5 port ethernet switch to one of the LAN ports on the Extreme and then plug all the devices connecting using ethernet....the iMac and the 3 AirPort Express devices...into the remaining 4 ports on the switch. That will leave you with 2 open ports on the AirPort Extreme for any future devices that may need to connect.
    When you test out the system, here is a trick to find out which device your computer is actually connecting to at any given time as it "roams" around the house.
    When you have AirPort Utility open to configure each AirPort Express, jot down the AirPort ID for each Express. You can do the same for the AirPort Extreme.
    As you move around with your laptop, hold down the option key on your Mac keyboard while you click on the fan shaped AirPort icon at the top of the screen. Look for the BSSID. That is the AirPort ID of the device that the laptop is connected to at that time. it should also be the ID of the closest AirPort Express (or AirPort Extreme if the laptop is close to the Extreme at the time).
    Let us know how things are working when everything is up and running.

Maybe you are looking for