Extender and networked hd recommendations needed

Hi all,
Looking for some recommendations. I'm using more and more devices at the far end of the house, away from the one cable connection coming into the modem (old house, and we rent, so not changing that). I have a 500g elderly seagate hooked up as a network drive to the time capsule, but just got a 2tb raid LaCie. What I'd like to do is to leave the LaCie in my office (NOT by the seagate and time capsule in the living room), and to, at the same time, repeat the wireless signal from the office back to the house's dead zone. I'm running a WPA secured network and would like to stick with tried and true (preferably apple) products.i have a MacBook In the office, but it's not always on. Need to run an Xbox, iPad, 2 iPhones, and MacBook off of this repeater (preferably on the inexpensive side). Does airport express fit the bill, or do you all have other suggestions? Thanks in advance.

An airport express will work as a repeater and the ethernet port still work.. but the range is not great. And wireless repeating halves the throughput at least and often worse.
If you cannot run ethernet which is fair enough in a rented place.. then try using EOP adapters. That gives you a link which is reliable and since it isn't wireless will not slow the connection at the other end. Then you can use an AEBS or even another TC in bridge and setup for roaming. This is easy and will give full speed at the other end plus give you 3 gigabit ports to attach stuff.

Similar Messages

Replace HD -where and who? Recommendations needed

Well, since my earlier post, installed Tiger in hopes of fixing problem but looks like HD is dead. Got tiger installed, transferred files/apps/settings from backup HD and started updating software.
Now HD making all sounds of scratching and squeaky noises and won't boot.
So, anyone recommend third party to replace HD. Don't need anything fancy, 60 gb 5400 rpm or 7200 rpm will do. And estimated cost?

You didn't say where you are located. If in the US, use this link: http://www.apple.com/buy/locator/service/ Outside the US the country Apple sites have a similiar link. This will tell you where Apple and Apple authorized service providers are near you. Note if you go to an Apple store, they will keep your old drive, however, since you have it backed up already, and can still erase it, that shouldn't be a concern.
You might as well get a slightly larger drive, as 5400rpm 60GB and 80GB, depending on brand, are about the same price ($50-$60). 7200rpm version would be around $20 more. If you have a choice, people seem satisfied with Seagate and Hitachi. Avoid Toshiba. Installation of course on top of HD cost. You may not have as many HD choices at an Apple store versus using an Apple authorized service provider.
It may or may not be cheaper for you to buy the drive and take it to an authorized service provider for installation. Newegg at http://www.newegg.com and OWC at http://www.macsales.com are two good sources. You'd be looking for a 2.5" notebook drive, with a parallel ATA attachment, not serial ATA or SATA (drives are well marked in the descriptions). If you buy it yourself, regardless of who installs it, you'd get the manufacturer warranty, so, for example, Seagate has a 5 year warranty. If Apple sells and installs it, you get whatever Apple warranty provides.

Time Capsule - extending a network

Okay...I must be dense, because I am not understanding the extended network ref Time Capsule. The question then is...I already have an Apple Airport network. I just purchased and Time Capsule. Can I extend my wireless network by linking the two airports together? At this point, I have the Lan connection from my imac going into the Wan port of the Airport. If I can use the two to extend the network, what are the next steps? Thanks for any help.

Welcome to the discussion area, justaglo!
The "main" wireless network must created by an Apple wireless router...an AirPort Express, AirPort Extreme, or Time Capsule could perform this function.
Then to "extend" that network, you would need another AirPort Express, AirPort Extreme or Time Capsule.
It sounds like you are using the Internet Sharing function of your iMac to furnish a small wireless network. This type of setup cannot be extended.

Cisco Jabber for Windows in Extend and Connect mode and making outbound calls

Hi guys,
I've set up Cisco Jabber for Windows to use Extend and Connect to control a remote PBX endpoint. I've configured the required CTI-RD device, remote destinations, associated the users to the line and added the devices to end-user controlled device. The extend and connect part is working flawlessly without any issues. I'm able to receive inbound calls on the remote PBX endpoint and control the call (hold, resume, transfer etc.) using the Jabber call window that pops up.
However, I'm unable to make any outbound calls via the Jabber client when in extend and Connect mode. Reading the Extend and Connect guide, I need to configure Dial Via Office (DVO) Reverse. So when the user initiates a Dial-Via-Office reverse call, CUCM calls and connect to the Extend and Connect device (CTI-RD). CUCM then calls and connects to the number the user dialled and finally connects the two call legs.
After attempting to configure DVO-R for Jabber for Windows in Extend and Connect mode following the CUCM feature services guide, i'm unable to get any outbound calls working. From RTMT, i am receiving the following Termination Cause Code: (27) Destination out of order. What i also notice is that there is no calling number for that trace either. I would've thought that the calling party would've been the Enterprise Feature Access (EFA) number.
Has anyone got this working or can provide some guidance?
Thanks.

Hi guys,
I've set up Cisco Jabber for Windows to use Extend and Connect to control a remote PBX endpoint. I've configured the required CTI-RD device, remote destinations, associated the users to the line and added the devices to end-user controlled device. The extend and connect part is working flawlessly without any issues. I'm able to receive inbound calls on the remote PBX endpoint and control the call (hold, resume, transfer etc.) using the Jabber call window that pops up.
However, I'm unable to make any outbound calls via the Jabber client when in extend and Connect mode. Reading the Extend and Connect guide, I need to configure Dial Via Office (DVO) Reverse. So when the user initiates a Dial-Via-Office reverse call, CUCM calls and connect to the Extend and Connect device (CTI-RD). CUCM then calls and connects to the number the user dialled and finally connects the two call legs.
After attempting to configure DVO-R for Jabber for Windows in Extend and Connect mode following the CUCM feature services guide, i'm unable to get any outbound calls working. From RTMT, i am receiving the following Termination Cause Code: (27) Destination out of order. What i also notice is that there is no calling number for that trace either. I would've thought that the calling party would've been the Enterprise Feature Access (EFA) number.
Has anyone got this working or can provide some guidance?
Thanks.

AirPort Extreme extends my network and has worked well for three months. Now it can no longer extend the network and flashes Amber. I have restored to factory settings moved it closer to time capsule and rebooted the system without luck

i have a blinking Amber on my extreme now and it cannot extend the network. It was working fine and nothing has changed. I have restored to factory settings moved it to another room and rebooted the system without luck. Any suggestions

What OS are you running?
Please give me a screenshot of the current AE setup..
I strongly recommend if you have issues.. take control of all the variables. Apple routers have too much auto..
Here is a list that I use for setups when using Yosemite.. but it relates to any OS.
You will need to factory reset again to get going.
Factory reset universal
Power off the AE.. ie pull the power cord or power off at the wall.. wait 10sec.. hold in the reset button.. be gentle.. power on again still holding in reset.. and keep holding it in for another 10sec. You may need some help as it is hard to both hold in reset and apply power. It will show success by rapidly blinking the front led. Release the reset.. and wait a couple of min for the AE to reset and come back with factory settings. If the front LED doesn’t blink rapidly you missed it and simply try again. The reset is fairly fragile in these.. press it so you feel it just click and no more.. I have seen people bend the lever or even break it. I use a toothpick as tool.
Then redo the setup from the computer with Yosemite or whatever you are using.
1. Use very short names.. NOT APPLE RECOMMENDED names. No spaces and pure alphanumerics.
eg AEgen5 for basestation.
Use AE24ghz and AE5ghz for wireless on each band, with fixed channels as this also seems to help stop the nonsense.
2. Use all passwords that also comply but can be a bit longer. ie 8-20 characters mixed case and numbers.. no non-alphanumerics.
3. Ensure the AE always takes the same IP address.. this is not a problem for router but if the AE is bridged you can have trouble.. Try using the static IP method or control it via the main router dhcp reservations.
4. Check your share name on the computer/s is not changing.. make sure it also complies with the above.. short no spaces and pure alphanumeric..
5. Make sure IPv6 is set to link-local only in the computer. For example wireless open the network preferences, wireless and advanced / TCP/IP.. and fix the IPv6. to link-local only.
6. Set up the extend to the Express using 2.4ghz and then see how good or bad the connection is.. this is better in the old v5 utility but if you hover your mouse over where it shows connection an extra chunk of info comes up.
I have specifically used 5ghz to make the extend.. because by testing it works better.. but do not be fooled.. this good connection is poor.. the RSSI.. which is difference signal .. at -79dbm is down the bottom of the stable.. and it drops out on a daily basis.. you want to see that signal around -60dbm at min.
There is a lot more jiggery pokery you can try but the above is a good start.. if you find it still unreliable.. don't be surprised.

IPhone 4 and network extender troubles

I live in an area where I need a network extender to receive a signal. All has worked perfectly fine in the last 4 years I've been with Verizon, until about 4 weeks ago when my daughter was trying to send me pictures that I never received. I then noticed a picture I had sent her didn't go through either. I'm usually connected to wifi, but when I'm not and try to access the internet it says "could not activate cellular date network".   I have tried every suggestion I could find on the internet from other people who have had this issue with no luck, and I do mean everything from toggling off and on this and that, to taking my phone back to factory settings, which by the way, even with no back up and just adding one picture and one contact this issue exists. When I'm in a 3G area I have cellular data and the phone works fine, including being able to send and receive pictures and being able to access the internet, so I have no reason to believe it's the phone or the settings. I'm thinking it has something to do with the network extender not playing nice with my iPhone because my husbands Android is able to send and receive pictures and access the internet with no problems.   I would also like to note that about 2 weeks ago I contacted support to see if they had any news, the tech tried sending me a picture which I did just randomly receive about 2-3 hours later, along with a picture my daughter had sent me earlier in the day. I asked her to send me another one which I got, but after that I tried sending her a picture and the problem was back.
I have been in contact with technical support and network support, who haven't really helped me. I don't think they know what the problem is so they just ignore me, as it's been 8 days since I've heard from them. I think 4 weeks is plenty of time to at least narrow it down. On my first ticket they asked me to run a speed test, which I did and they were going to check the towers. They called me on my cell, but I missed the call, thanks for leaving that VM though, no cellular data=no VM, so I didn't know until days later you left a message saying no problems were found. So I had to start over again, two weeks since the problem started.   On my second ticket they said they didn't do the first ticket right, a week later they called back asking for another speed test, which came back above minimum requirements, they were going to pass it on to network support and here I wait 8 days later, 4 weeks total with no end in sight.
Today I stopped at the Verizon store hoping they'd have some suggestions. They said they couldn't do anything on their end, I'd have to call technical support...The only thing they told me that was new was something about a security breach with Samsung extenders, and maybe an update was pushed to my extender that's not playing nice with iPhone. But how do I check on something like that, who do I report this to??   If that was the case wouldn't Verizon tech support know about it? I'm not getting any help and I don't feel like anyone at Verizon really cares, but you can bet if my payment was 4 weeks late there'd be an issue.
Any suggestions?

How old is the extender? Can it support 1x or both 1x and 3G? Try checking the Network Extender space for more suggestions and similar questions.

I have an Airport Extreme as my router and am using time capsule to extend the network in my new house. My ISP is only providing me 4-5 ip addresses and wants me to set up my router to issue out new ip addresses for all my devices.How do I fix this?Help

I have an Airport Extreme as my router and am using time capsule to extend the network in my new house. My ISP is only providing me 4-5 ip addresses and wants me to set up my router to issue out new ip addresses for all my devices.How do I fix this?Help.
They said I need to change my settings to NAT settings. I haven't been able to figure out or find anything. I have also spoken to Apple Support on the phone for hours without being able to figure out how to do this ( i don't think he knew much either lol.) Please help me because I've got about 15-20 devices in my house that require to be connected to the internet and this is just making things ridiculously slow and painful for me.
Thanks!

It is on DHCP & NAT under router mode yet my isp is still the one issuing ip addresses to my devices instead of the router issuing them

I updated an iPod touch, an iPad 2, and an iPhone 4 to iOS 6, and all of them now will not connect to WiFi. They all give this wierd 404 error page from Apple and insist that I need to login to the network. Bad job testing the software Apple.

I updated an iPod touch, an iPad 2, and an iPhone 4 to iOS 6, and all of them now will not connect to WiFi. They all give this wierd 404 error page from Apple and insist that I need to login to the network. What's the fix? None of the recommended fixes work in any of these devices. Reset device, reset network, renew lease, etc. None of them work.

Does the iPod work OK?
Does it charge when connect to the computer?
Does it appear in My Computer?
Look at the dock connector on the iPod. Compare with the iPod that does work/connect.
I suspect you have a 2G iPod. Those can only go to iOS 4.2.1
http://support.apple.com/kb/HT1353#iPod_touch_late2009
iPod touch (3rd generation)
iPod touch (3rd generation) features a 3.5-inch (diagonal) widescreen multi-touch display and 32 GB or 64 GB flash drive. You can browse the web with Safari and watch YouTube videos with Wi-Fi. You can also search, preview, and buy songs from the iTunes Wi-Fi Music Store on iPod touch.
The iPod touch (3rd generation) can be distinguished from iPod touch (2nd generation) by looking at the back of the device. In the text below the engraving, look for the model number. iPod touch (2nd generation) is model A1288, and iPod touch (3rd generation) is model A1318.

Troubling extending wireless network with Time Capsule and Airport Extreme

I am trying to set up and extend a wireless network in my house, but it’s not working right. I have two Airport/Capsule units in the house:
2TB Time Capsule (Dual-Band II)
1 Airport Extreme (Dual Band)
I have the Verizon Fios router as my gateway to the internet, and also as my DHCP server. I have also tested the ethernet ports in my house to verify that they work, and that I can get a DHCP-issued IP address.
Now, my Verizon router has WiFI, and it’s still on. I am not using it though except to troubleshoot. So far as I understand, this should not cause a problem.
Base station setup
So I setup the TC to Create A New Wireless Network, on the ethernet network it’s on (Dlink switch plugged into Verizon router). I set it up in Bridge Mode (as opposed to having it dole out IPs, since the Verizon router does this already). The TC gets a valid IP, and my wireless device connect to it without a problem. I have checked “Allow this network to be expanded” under Wireless settings.
Extended station setup
The AE Dual-Band is plugged into the Ethernet, and is reset to Factory Settings. I name it “Airport Extreme 2” and I chose “I want Airport Extreme to join my current network.” The other two options are: “I want to create a new wireless network” and “I want to replace and existing base station or wireless router with Airport Extreme.”
I chose to “join,” I select “I want to connect Airport Extreme to my network using Ethernet to extend my existing wireless network.” The other options are to disable wireless entirely, or to “wirelessly join my current network.” On the next page it asks me to select the device or network that the Airport Extreme will connect to using the Ethernet. I set it to the Time Capsule.
Results:
Access near the Airport Extreme 2 is incredibly slow. Speedtest shows I am getting less than 1Mbps. Worse yet, my mail client won’t connect. It just times out.
What I had hoped was that the AE would connect via Ethernet to the network, and just bring the wireless network to the other side of the house. Instead it almost seems as though it is just re-amplifying the TC’s signal. Otherwise, why is performance so bad?
Thanks to anyone with some insight here!

Hello Kennuff. Welcome to the Apple Discussions!
Since you have the ability to connect all of the routers by Ethernet, there is no need to configure the Time Capsule (TC) & 802.11n AirPort Extreme Base Station (AEBSn) for a dynamic WDS (aka, extending a network). This option is only when the routers do NOT have an Ethernet connection between them.
Instead, you want to configure the TC & AEBSn in a "roaming" network. I suggest starting by performing either a "hard" or "factory default" reset on both.
Next be sure that both the TC & AEBSn are on the same Ethernet subnet coming from the Verizon-supplied router.
Configure the TC & AEBSn as follows:
AirPort Utility > Select the TC or AEBSn > Manual Setup > AirPort > Wireless
o Wireless Mode = Create a wireless network
o Allow this network to be extended: <not checked>
o Radio Mode: <leave the default or if you require a specific mode make sure both routers are configured the same>
o Wireless Security: <configure both routers the same>
AirPort Utility > Select the TC or AEBSn > Manual Setup > Internet > Internet Connection
o Connection Sharing = Off (Bridge Mode)

Extending a network with Time Capsule and AirPort Extreme (via Belkin powerline)

Hello -
I've seen many topics about extending wireless networks here, but none seems to resolve the issue I'm having. I currently have a setup where a DSL cable modem is connected to a Time Capsule and I need to extend this network to another room using an AirPort Extreme.
I live in a very old apartment in Brazil and the walls seem to block the signal from one room to another, hence the need to extend it. Since wireless signal is very weak between rooms, I bought a Belkin powerline AV500 so I could connect both Time Capsule and AirPort using the electrical power at home (just installing a regular Ethernet cable between rooms is not an option).
I started with the basics: configure the Time Capsule + DSL as a standalone network, and it works perfectly within it's range. Then I connected the Belking powerline, plugged a MacBook via Ethernet on the other end and still got very good results (actually better speed than expected). Used it for a while with streaming and other network intensive tasks to make sure it could sustain the connection.
Finally, pluggned the AirPort Extreme on the Belking powerline and this is where the problems started. AirPort Utility 6.3.1 only gives me the option of extending a network wirelessly - it doesn't seem to give me the option of extending it via Etherenet (roaming), which is not good in my case. Luckly I had a copy of AirPort Utility 5.6 which seems to do the job (or I thought so), but it's still not working well.
Although I managed to configure both with the same name, it doesn't seem reliable and some devices (the iPhone 5, for example) are unable to connect and end up with a self-asigned IP address. I'm almost sure I'm doing something wrong on the setup, as I've seen a similar setup working before, so if anyone out there has any clue of what can be done, it will be much appreciated.
Attached the screenshots of both Time Capsule and AirPort Extreme configurations.
Thanks a lot,
-TM
AirPort Exteme:
Time Capsule:

Hello JuliaApple. Welcome to the Apple Discussions!
You have several ways to configure both base stations for what you are trying to do.
The simplest would be to configure the Time Capsule (TC) to "join" (AirPort Utility > Manual Setup > Wireless tab > Wireless Mode = Join a wireless network) your existing 802.11n AirPort Extreme Base Station (AEBSn). In this type of configuration the TC would perform as any other wireless client and not perform as a router. It will; however, still allow for both backups and sharing USB devices attached to it.

How do I install a new airport express and link a second airport express to extend the network of the first airport express?

I currently have a linksys wireless router attached to the Internet. I have an A1264 Airport Express connected by Ethernet to the linksys router. I have two network names, one for each wireless network.
I purchased a new A1392 Airport Express to replace the linksys router and join to the A1264 Airport Express, and I want to have one network name as a result.
How do I do this? I realize that I have to reconfigure the A1264 device so that it is an extension of the A1392 device.

You have a fairly complicated set up, so I suggest that it would make sense to tackle things in stages, testing each stage as you go, before proceding to the next stage.
Stage 1 would be setting up the A1392 first to the cable modem, and then making sure that everything is working correctly on the A1392 Express
Stage 2 would be adding the Netgear switch and testing each port with a laptop connected via Ethernet to make sure that everything is operational on the switch
Stage 3 would be connecting the A1264 Express and testing to make sure that it is extending the network correctly
Stage 4 would be adding other Ethernet devices to the Netgear switch and testing each one at a time before adding the next device. There is some question about whether an iOS device can print to an Ethernet connected printer....even if the printer is AirPrint compatible. You may need to connect the HP using wireless...not Ethernet....to gain full AirPrint functionality, or use another application that will allow printing like Printopia or Print Central using the Ethernet connection on the HP.
Stage 5 would be adding the printer to the A1264 AirPort Express.
You do not mention how the printer will connect to the A1264 Express, but I assume that it will be USB from your description. Most printers will work, but you really will not know if your printer will work until you try.
Remember that only printing will be supported at the USB port of the Express. If you have an all-in-one type device, scan, maintenance, and other advanced features will not be operational whent the device is connected to the AirPort Express.
If you want to print from an iOS device like an iPad or iPhone, plan to add additonal software like Printopia or Print Central to possibly allow this function. There are no guarantees here as far as the iOS devices.

Do i need to use airport express to extend my network to use AirTunes?

I use an AEBS connected to my cable modem and just bought the Airport Express just to be able to stream my iTunes music to a set of powered speakers conncted to it.
When I got into Airport Utility, the only options it provides is to Set up a new network, add to an existing network or replace an existing network.
I just to add to an existing network and it says Airport Express will be used to extend my network.
Now - is that how it's supposed to work? Does it have to extend my network in order to use Air Tunes? The reason I ask is that I remember reading on the forums that extended your network can slow it down....

Bob Timmons wrote:
Version 6.0 will not allow you to configure the Express to "Join a wireless network" if you have another AirPort providing the wireless signal.
If you want the Express to "join" the network, you will need to download and install the much more functional AirPort Utility 5.6 for Mac OS X Lion , which was available on the same day as AirPort Utility 6.0.
Apparently, a number of users missed this.
Suggest that you keep both 5.6 and 6.0 on your Mac and use the one that is most useful.
That is NOT correct.
Version 6.0 will allow you to "Join a wireless network" if you have another Airport providing the wireless signal.
I have an Extreme provinding the wireless network and have 2 Express units Joining the network.
Here is a screen shot of version 6.0 and the Express settings.
You must have missed this in your settings.

Friend suggested I use Airport Express to extend my network to fix dead spots, should I just plan on replacing existing Netgear and buy two AXn's?

I have a few dead spots around the house and I am seeking a good solution without pulling ethernet cable. Reading this community it would seem best if going with Airport Express solution to replace my Netgear and pick up a couple of AXn's. Or perhaps Airport Extreme for base at cable model and AXn for extension?
I had assumed I could just configure one AXn and put it in the dead zone, but reading configuring roaming network indicates you need two. I was planning on adding Apple TV in extended zone does this change anything?

There are a number of possibilities of using multiple AirPorts to extend the wireless range of your network without using wires. Please check out this Apple Support article for more details.
Since your goal is to use wireless connections between routers, you will need two or more AirPort to accomplish this. Unfortunately, extending the Netgear by wireless will not work due to WDS compatibility issues between router manufacturers.

How to extend secure network and guest network.

Sorry if this has been covered but I couldn't find it.
I have an Airport Extreme running the 7.6.3 firmware. Once Comcast gets their act together it will be running off a static IP. I want to wirelessly extend my guest WiFi and my secure WiFi. What do I need to get this done? Do I need to get an Express for each network? Or can another Extreme repeat both networks? Eventually I hope we will have Cat5 running to the repeater's location but that could be a long way off.
Thanks!

I cannot get the web page to open when I do a search on the SMC8014, but it appears that this is a modem/router or gateway type of device.....which will not allow the Guest Network feature to be enabled on the AirPort Extreme.
I did find this, which confirms that the SMC is a modem/router or gateway....not what you want.
http://www.speedguide.net/routers/smc-smc8014-biz-business-cable-gateway--534
The solution is to find out from SMC or your Internet Service Provider whether or not the 8014 can be configured to operate in "Bridge Mode".....which would then allow you to configure the AirPort Extreme to operate as the main router on the network. This would allow the Guest Network option on the AirPort Extreme to be enabled correctly.
Or better yet.....ask your ISP for a simple modem.......not a modem/router or gateway type of device.
So assuming this is all compatable (or I get compatable equipment), I can extend both networks with 1 express or 1 extreme?
That is correct.

What's the difference between WDS and Extend Wireless Network?

Hi,
I have a situation where my main computer (Mac Pro) is wired to an Extreme (n), and I have an Express (n) in another room in the house to Bridge to other computers for better wireless reception.
The manuals say I should be connecting the wireless computer via WDS. The way I have it connected right now is as such.
Extreme:
Create a wireless network
Allow this network to be extended is checked
Express:
Extend a wireless network
Allow wireless clients is checked
Is the above method correct, or should I be setting the Extreme and Express via: Participate in a WDS network?
Any help would be appreciated.
Thanks!
Message was edited by: Imagine
Message was edited by: Imagine

I am not an expert on wireless networks but here is what they do in a nut shell:
WDS is a network composed by access points that work together to expand your network without the need of "wired" connectivity. so one of the bases will be wired, the rest are not , they just relay info to other computers... good for small to medium size business / homes
EWN is a network composed of wired & wireless networks/access points that work together to expand your network. pretty much you could have 5+ bases plugged in to a LAN / WAN covering different areas of your company / home (long range for medium / big business / Bill Gate's home, etc.).

Extender and networked hd recommendations needed

Similar Messages

Maybe you are looking for