Extending a network with airport express

I have been using a Be Box modem for my wireless internet connection but it is a fair way from my downstairs area - where I use a laptop and my upstairs area where I use my computer (Imac).
I thought I would be able to extend my be box signal by creating a network. I extended the network and when doing so gave my airport express the same address as my bebox.
I can now connect to my bebox modem (by chosing it from wireless drop down) but cannot use airport express for itunes - the airport express blinks orange.The bebox has WPA security (which is a recent change and has caused issues between modem and express in the past)
Or, I can chose the airport express from wireless drop down box and play through my imac airtunes (light is green) but I cannot use it for internet browsing on my pc laptop or the imac.
Any, any ideas on this ???

Paul - you have essentially two similar discussions going on here, and I suggest you continue further discussion in the thread you titled "Client mode and WDS" found at:
http://discussions.apple.com/thread.jspa?threadID=1341580&tstart=0
To answer your last question and "wrap up" this discussion - you asked:
"It would seem the two are not linked properly ?? Is there a way to do so effectively ?"
Yes, there is a way to set this up properly and effectively. If you run the Airport Setup Assistant, choose the option to configure the Airport Express so that it "joins" the existing wireless network created by your Be Box. When you are done, you will have a single wireless network (still based around your Be Box) that will allow you to access the internet and stream music to the Airport Express at the same time. Note that selecting the option to have the Airport Express "join" a network (ie "client mode")is NOT the same as selecting the option to "extend" your existing network (ie "WDS mode") which is an option not available to you for reasons I already mentioned previously. The difference between the "join" and "extend" options may seem subtle, but they are indeed very different.

Similar Messages

  • How do i use my time capsule and extend the network with airport express

    I have a new iMac and Time Capsule, how do i extend the network with airport express. My time capsule does have a guest net work, and logins and passwords? I am no computer person. So for me it would have to be spelled out.

    Use the search as this has been done to death ..
    Bob Timmons is the expert on this.. look at his answers here.
    https://discussions.apple.com/thread/4274187?start=0&tstart=0
    https://discussions.apple.com/message/21856077#21856077
    This has been automated in the v6 utility. I am used to doing it manually in v5 utility which is also fairly easy.
    Apple doco is also good to read.
    http://support.apple.com/kb/HT4145
    http://support.apple.com/kb/HT4259
    Note.
    You cannot extend the guest network unless everything is up to date 7.6.3 firmware. And that is only with the TC as the main router in the network.
    All apple routers can be configured as the main wireless or as the extend wireless.. so don't worry if a post uses express or extreme or TC.. they are for wireless, the same thing.

  • Extend wireless network with AirPort Express

    How to extend the wireless network with AirPort Express and Belkin PlayMax as the primary router ?

    How it work if I have an AirPor Station and 4 Airport Express, I actually also have an old TimeCapsule and an old AirPort Express. Can I cover all my house (around 300 m2). And will the old Airport slow down or convict with the new ones?

  • HT4259 Why won't AirPort Utility let me extend my network with AirPort Express?

    I have 2 1st Gen AirPort Express stations. I have my original AirPort wired into my modem with an ethernet cable and it works fine. I have my new AirPort plugged, well within range of the network but it doesn't show up in AirPort Utility making it impossible for me to extend the network.
    All of the previous forums I've seen say to reset both routers and "set up manually" and select the box that says "allow this network to be extended". When I go to setup there is no option for either of these.
    Am I missing something? What am I doing wrong?

    All of the previous forums I've seen say to reset both routers and "set up manually" and select the box that says "allow this network to be extended". When I go to setup there is no option for either of these.
    You are looking at instructions that apply to Snow Leopard and earlier operating sysems. You are using Lion or Mountain Lion.
    Hold in the reset button on the Express that you want to use to extend for 9-10 seconds and release.
    Close AirPort Utility if if it open.
    As edex67 notes above, click the fan shaped AirPort icon at the top of the screen and look for a listing of New AirPort Base Station. Just below that, click directly on AirPort Express.
    AirPort Setup will open automatically and take a minute to analyze the network, then tell you that the Express will be configured to "extend" the network.
    Enter a device name that you want to use for the Express and click Next
    AirPort Setup will take a minute to configure things. When you see the message of Setup Complete, click Done.
    You are done, other than locating the Express approximately half way between your "main" Express and the area that needs more wireless coverage.

  • Extend Wireless network with Airport Express via Cat6 cable to Cisco E4200 router.

    Hello there! Totally new to this, but I've been doing a lot of research, and have been getting conflicting answers, so maybe someone can help me out. I've been reading that you cannot wirelessly extend your network unless you have a time capsule or an airport extreme.  However on some forms, if you have the airport express hard wired to the router(in my case a Cisco E4200), you should be able to extend your network.  Is this accurate?  If so, can someone please post steps on how to do this?  Thanks!

    How it work if I have an AirPor Station and 4 Airport Express, I actually also have an old TimeCapsule and an old AirPort Express. Can I cover all my house (around 300 m2). And will the old Airport slow down or convict with the new ones?

  • Extending Wireless Network with Airport Express / DLink Wireless

    I have a DLink wireless router WBR-1310. I own two Airport Express 802.11n's. Can anyone help me out with how I can properly set-up an extended network with these products? All help is greatly appreciated.

    You would need one AirPort Express located near the D-Link router and connected to the D-Link with an ethernet cable. This Express would be configured to "create a wireless network" and "allow this network to be extended"
    If you have two areas that need more wireless coverage, you would locate an AirPort Express approximately 1/2 the distance between the "main" AirPort Express and the area that needs more wireless coverage.
    Then do the same with the second area that needs more coverage.
    Without knowing your room layout, I can't honestly tell you whether you need only one "extending" Express or more than that.
    It will help to remember that the "extend" setup works like the hub and spokes of a wheel. Your "main" Express connected to the D-Link would be the "hub". Each of the "extending" Express devices would be at the end of a spoke. The Express devices at the ends of the spokes communicate directly to the hub, not to another Express at the end of another spoke.
    So, to work well, hopefully your D-Link router and Express will be located in a central area of your home so the extending devices will work around the perimeter.
    I would recommend that you study Apple's support document on extending wireless networks before you make a final decision on what to do.
    http://support.apple.com/kb/HT4145
    Finally, consider if you can connect the two Express devices you have now back to the D-Link using ethernet cables. This would provide much better performance than a wireless only situation.

  • Cannot Extend my Network with Airport Express

    I have an existing Airport Express that was used to Extend my network from my AP Extreme.  It's now flashing amber, so when I went to see it in Airport Utility, it was no longer there.  I had to reset my Express base station a while back, so it may have disconnect the 'extend'.  I reset the express and then re-opened the Utility, I saw it and tried to configure it, but it failed.  Now when I open the Utility (with the Express unplugged), the Extreme base station is not showing.  if I plug in the Express, it's the only one that shows.  Somehow the Extreme is working (even when Express is unplugged) and I have a wireless connection, but I still don't see it in the Utiltity even after doing a rescan.  FYI - I run Windows 7

    I should have posted this as a question so I could close it (I'm new to this).  I found the answer to my question in another post. 

  • Extending a network with Airport Express 802.11n-2.4 or 5.0GHz?

    I've just ordered an AirPort Express N to extend the network of my AirPort Extreme (Gigabit) and run AirTunes. It'll be connected to the router by Ethernet.
    My question is this: can I run the Express at 2.4GHz (802.11b/g/n) while I run the Extreme at 5.0GHz (802.11n only), even though they're on the same network? I've got a couple of 802.11g machines (my old iBook and my iPhone, for two), so I need to keep backward-compatibility, but I'd love for the 802.11n machines (my iMac, and my wife's Mac Book) to connect at the higher speed. Can you extend a network on different frequencies?
    Message was edited by: David Kudler

    My question is this: can I run the Express at 2.4GHz (802.11b/g/n) while I run the Extreme at 5.0GHz (802.11n only), even though they're on the same network?
    No, not while they are in a WDS. If you want to operate wireless networks in both radio bands, you would need to configure the base stations in a "dual band" network.
    Setting up a "dual band" network is described in the Designing AirPort Networks document, starting on page 48.

  • Extending network with Airport Express and Airport Extreme (latest models) causes chaos on network

    Today I upgraded from my several year old Airport Extreme (3rd gen) and 2nd gen Airport Express to a new (what you'd buy on the shelf today) Airport Extreme and Airport Express.  All airports are updated with the latest firmware and I'm using windows 7 for configuration.
    The intention is to use the Airport Extreme as the main router, also serving wifi. And extend the network using the express. As such, the following has been done:
    The Airport Extreme is configured for automatic channel, and automatic radio mode. I tried to select 802.11n 5 ghz and 802.11 n 2.4 ghz only, but it won't take the changes. Additionally, it wont' accept me using only channel 6. Not sure why, but I digress. The airport extreme is not set to broadcast a separate name for the 5ghz network.
    The Airport Express is configured to use bridge mode, use an existing wireless network and is connected to my network on it's WAN port (the circle icon on the back) with ethernet. The password and wireless name used in configuration is the same as created initially on the Airport Extreme.
    Initially I did the configuration of both airports on my computer, connected by ethernet to ensure stable connectivity while I inputted settings. During this, they appeared to accept the changes fine. However, when I moved the airport express to it's destination (other side of my house), the entire network went crazy.
    Internet became slow, and often wouldn't load pages. This was on wired and wireless connections. When I attempted to administer the Airport in the Utility, they would not load, an error would occur. Also, at one point the Airport Extreme had renamed it self with a (2) at the end. Which was super odd. So far, the only solution has been to unplug the Airport Express and attempt to devise a solution.
    Anyone have any ideas? Of course, I will continue to tinker with this, but it seems realllly strange. The previous setup was also extended (granted, using wireless only, not ethernet > wireless) and worked fine, granted it was a smidge slow, but it worked.

    I wanted to add this.. I followed the guide here: http://support.apple.com/kb/HT4260 to extend using ethernet, and the above is the result.
    I just tried re configuring in OS X Mavericks and got the same, odd, result.

  • Can't extend network with Airport Express on Sky Broadband

    Hello,
    I'm having some difficulty that's driving me bananas!
    I've recently moved house and got Sky Broadband. They sent me their Sagemcom router and the setup was easy. I thought I'd do what I always do. I'll connect my Time Machine to it via ethernet, and connect via Time Machine's network. Then I have two Airport Expresses in the house to extend the network and use Airplay etc.
    I can set up the Expresses with no problem, everything talks to everything without a problem and the lights are all green  but the network isn't getting extended with either of them. I refuse to believe they're both broken as I also borrowed an Express form my Dad's house (which extend the network without a problem) and it doesn't work with me.
    Extend my network is checked in the Manual Setup in Airport Utility but for the life of me I can't get my network extended.
    I have done tests where I replaced Time Machine and made one of the Expresses the main base station and it throws signal out easily like that but I can't extend that network with the second Express.
    I followed this thread https://discussions.apple.com/message/13171691?messageID=13171691 and have tried a few things to no avail. Currently I have configured an old Airport Extreme (just to keep testing) which works great and have set up an Express wirelessly. All lights are green and the settings seem to all be correct. I turn wifi off on my computer and connect to my computer from the Express using ethernet and nothing. Should I get a connection like this?
    Is it Sky? I have read in a few places that Sky have disabled the ability to extend their network but I'm not eve using the signal from their box.
    Any ideas or thoughts will be gratefully received.
    Thanks in advance.

    OK so I've been tying it out but unfortunately to no success. Everything looks fine and all lights are green but the network isn't getting extended - just as before.
    Click the Wireless tab
    Wireless Mode = Extend a wireless network
    Wireless Network Name = Same name as the Time Capsule network
    Check Mark next to Allow Wireless Clients
    I don't have an option to extend a network, only to join: http://flic.kr/p/a222kR
    I do get the option though if I use the guided setup, even though it doesn't work: http://flic.kr/p/a24TQQ
    I did try one other thing though. I set up the Time Capsule and it works great. Then I tried instead, to use my Airport Extreme to extend the network. The Extreme did give me an option to extend the network in the drop down menu and a checkbox to Allow Wireless Clients, unlike the Express. I do believe that this is now working. I now need to find the best place to put it to extend the range.
    My Expresses are only 802.11g so they're pretty old but as I said, it worked at my Dad's house but not here. Does it make a difference that the Airport Base Station at my Dad's house is an older UFO shaped Snow Airport? I'm becoming suspicious that seeing as I've only ever lived in small houses and apartments that maybe they never worked?? I've recently moved into a more spacious house so could this be the problem?
    One final test using iStumbler showed that it could see Apple Network XXXXxX until I configured it. Once it was configured it disappeared from iStumbler. The Airport ID number had gone from the list.
    Do I need newer n compatible Airport Expresses then? So many questions pop up now... When I turned my Express into the base station (which only throws out a g network) then surely I should be able to extend to the next Express (which is also g only)? It still didn't work. The Express are on version 6.3 by the way. Having the Extreme extend the network is a good start but I also need the others to work too. Do you think I'm correct in my assumption?
    How about WDS, could that work? Will WDS slow the network considerably?
    Sorry if this message is rather long and garbled and again, thanks for your interest and advice.

  • How do I extend my WiFi with Airport Express? I have Ethernet in the house and an Wifi that do not cover the whole house. I do not get it to work.

    I have Ethernet in the house and an Wifi that do not cover the whole house. I do not get it to work. I have tried to get it into my network and it get connected via the WiFi but not the Ethernet. Also when it gives a green light I cannot see that it is giving any signals to my devices (iPhone etc).

    You need to pay attention to something, while extending your network with the latest AirPort Express upgrade, your devices will be connected to it except your iPhone, you'll see your iPhone always connected to the capsule instead, even if you're at 1 foot from the AirPort Express.
    You need to change the radio settings from automatic to 802.11a - 802.11b/g on your capsule, then I put it back to the default settings...
    Now in the AirPort utility you should see your iPhone connected to the AirPort

  • How to create a wifi network with airport express in hotel room?

    When I'm traveling to hotels that have internet, but not wifi, how do I set up a network using airport express?  When I've done this at home, I've used my laptop with the airport utility.  Can I do it with just an iPad?

    Yes, you can use the Airport Utility for iPad here:
    https://itunes.apple.com/us/app/airport-utility/id427276530?mt=8

  • I have installed Airport Extreme on my iMac, but want to extend the wireless network with Airport Express. Everything is fine until I try to select Extend the wireless network.  I select Extend Wireless network but have no success. Ideas?

    I have installed Airport Extreme on my iMac, but want to extend the wireless to rooms with a weak signal.  The internet connection is fine with the basic setup. As soon as I go into Airport Utility to select Extend Wireless Network and fill in what I believe is proper information, I get an error message that Airport Extreme no longer has an IP address, the internet connection is broken, and under Wireless, that there is a wireless network in existence that can't be found. Rebooting the modem only brings the Airport Extreme back to the starting gate so that the internet is once again available.  I assumed (naively) that with the All Mac All-the-Time context, adding Airport Express would truly be Plug and Play.   I got the plug, but no play.  I asked a Comcast technical specialist about it and he said that I needed to reset the Airport Express settings back to their default, factory status.  I looked that process up online and found out that the way to do that was to hold down the reset button, then plug Airport Express into the socket and wait for the green light to flash four times.  Then wait 45 seconds and the default settings will return.  I did all that, only to find out that after the initial flash of green, green never appeared again.  I got a fast flashing yellow light, followed by the light going off.  Apparently this didn't reset it properly.  So, after hours trying to get this system to work, I appeal to someone who can see through this mess and provide the key to success!
    highFly376

    Let's see if I can get this straight.
    You have an Airport Extreme base station that is set to "Create a wireless network" and you have the box checked for "allow this network to be extended"....
    Then you have an Airport Express that is set to "Extend a wireless network" which you selected the name of your network in the box...
    Correct?
    See this Apple document:
    http://support.apple.com/kb/HT4259?viewlocale=en_US&locale=en_US
    The wireless unit on the right of the diagram can be either of the newer Apple base stations.
    Extreme, Express, Time Capsule

  • How do I set up for extending my non-apple wi-fi network with Airport Express?

    I have Trendnet router that I use for providing wi-fi capabilities in my home.  The problem is that it is set up in my basement and it doesn't extend to the back of the house.  I'm also having problems setting up my wireless printer with this setup.  I thought that by getting a AE, I could take care of these two things.  I could set up the AE upstairs to repeat the wireless signal and at the same time have an easier set up (as in an apple).  But, I'm not sure how to set it up.  Can someone help?

    Do you have a separate modem and Trendnet router now, or is the Trendnet a gateway....combination modem/router in one box?  If you add another AirPort at this location, it will need to connect to a modem, or it could connect to your Trendnet router and you could turn off the wireless on the Trendnet
    If you go wireless all the way, what is the approximate distance between the "main" router and the "remote" AirPort?  How many walls will be in the signal path?  How are these walls constructed?
    In general....I have found that power line works better than wireless....unless you have a very good wireless connection. If you take your computer to the remote area where the extender will be located, and you can get a good, solid wireless signal, you are probably OK.  The Express can only "extend" the quality of signal that it receives.
    But will the wireless setup for video streaming (which is my main goal) be reliable?
    Questions like this cannot be answered because it is just not possible to predict wireless performance and results in advance of any installation.  The products might be great....but other wireless networks around you or cordless phones cause interference problems.
    In this regard, If I only had one chance at a network, I would go with wired connections over wireless.
    If you go with the 2 AirPort Express plan, I would suggest that you still have a "Plan B" if wireless does not deliver the performance you want. Personally, I would never try to stream video, especially high definition, over wireless here at the house, but it can work if everthing else falls into place....and the planets are in the right alignment.

  • Extend wireless network with Airport Extreme n and Airport Express g

    I have a 4th generation Airport Exteme (n) and an older Airport Express (g) and would like to use the Airport Express to extend my network to the other end of my house, where the signal is very weak. When I tried to set it up tonight, my Airport Extreme disappeared all together and I had to do a hard reset to get it back. I am using a macbook pro 2.4 GHz Intel Core 2 Duo running OS X 10.7.2.  Are there any current insturctions to do this?

    Here's a Youtube video of how to do it. http://www.youtube.com/watch?v=e3EdbRfX1_w
    I had the same set up you do. I did not have success with the Express g. And in my case I had much better success when I sold the Express g on ebay, bought an Express N from the refurb store, so it only cost around $20 get something that is much more reliable.
    I quickly tried to find an Apple Support tech note for you but didn't, post back if you need more.

Maybe you are looking for