Extending aiport express to another airport express

I am having trouble extending my wireless network from one airport express to another. I had flashing amber the whole time with 2nd airport express, and caused the first to completely crash, needing to be reset to factory settings after an hour of troubleshooting. Is there an easy way to do this? Thanks.

"Factory Reset" the AX base stations
- (ref: http://docs.info.apple.com/article.html?artnum=108044)
Wireless Distribution System (WDS) Setup
(Note: To facilitate setting up the base stations, place them in near proximity of each other during the set up phase.)
Set up the AirPort Express Base Station (AX) as the WDS Main Base Station, by connecting directly, using an Ethernet cable, to the Ethernet port of the AX, and then use the AirPort Admin Utility to make the following settings.
WDS Tab
- Enable this base station as a WDS: main base station (checked)
- Allow wireless clients on this base station (checked)
- Click "+" to add Remote/Relay Base Stations.
-- Select the Base Station that you want to be the WDS Remote/Relay.
-- AirPort ID: <verify that this is the correct MAC address for the Base Station you are adding as a Remote/Relay.
-- Auto configure as a WDS remote base station (checked)
-- Click "OK."
- Verify that the Remote/Relay Base Station has been added to the list.
- Click "Update," and then verify the settings for the Remote/Relay.
-- Allow wireless clients on this base station (checked)
-- New network name: <verify that this is the same as the network name for the AX>
-- TCP/IP: Configure using DHCP
-- Base Station Password: <the Remote/Relay Base Station password>
-- Confirm: <same as previous step>
-- Click "OK."

Similar Messages

Is it best to extend a Wifi network using Airport Extreme 802.11ac or Express ?

I previously asked this question with a different emphasis here:
https://discussions.apple.com/message/24347878#24347878
so have re-worded to be more relevant to the subject.
I have a brand new Airport Extreme 802.11ac which I am now using as my network hub and I would like to extend the network wirelessly.
Is there a benefit to extending the network via another Airport Extreme 802.11ac versus a (cheaper) Airport Express ?
I do not have any 802.11ac clients yet, but likely will do within the expected lifespan of the routers and thus would rather buy another Extreme now if it meant extending the best signal strength.
Per my previous post i would ideally extend using my old Edimax BR-6675nD 450Mbps 2.4GHz/5GHz, however this has been problematic and some previous posts imply that mixing Apple and non-Apple routers is not recommended, if this is not correct please do let me know.
Thanks in advance.

Is there a benefit to extending the network via another Airport Extreme 802.11ac versus a (cheaper) Airport Express ?
Four possible benefits, which may or may not be benefits to you:
1) A second Extreme will extend the faster "ac" speeds of the main AirPort Extreme, while the Express will not.
2) A second Extreme uses Gigabit Ethernet ports....ten times faster than the Express....if you plan to connect devices using an Ethernet connection
3) The USB port on the AirPort Extreme will accept a hard drive while the Express will not
4) The AirPort Extreme has a much better antenna arrangement than the Express, which will provide greater coverage even if "ac" wireless is not used
On the other hand, if you do not need "ac" wireless to be extended, you only plan to use the Express to extend the wireless, and the Express will be located where it can receive a strong wireless signal, then you might save a bit of money going with an AirPort Express.
So, in questions about what would be "best", there are rarely simple answers that apply to all users. The question really is which is "best" for you. Adding another AirPort Extreme would be a no brainer for me, but perhaps not for you.
i would ideally extend using my old Edimax BR-6675nD 450Mbps 2.4GHz/5GHz, however this has been problematic and some previous posts imply that mixing Apple and non-Apple routers is not recommended
It is always the best idea to use products from the same manufactuer for the same purpose throughout the network. Obviously, an Apple AirPort Extreme will be compatible with another AirPort, while a third party device may or may not be.

HT4145 I have an Airport Extreme bas station now and I want to know if I can use an Airport Express to extend my network or do I have to use another Airport Extreme base.

I have an Airport Extreme Base Station now and I would like to know if I can use an Airport Express to extend my wifi network or do I have to use another Airport Extreme Base Station.

This AirPort Express:
http://www.apple.com/airportexpress/
It is the only Express with 2 Ethernet ports. All others are "old"
Apple does not specify a model number in their product information, but it is A1392 in the U.S. I do not know if Apple uses different model numbers in other countries.

Extending airport express wireless network with another airport express

I am trying to set up another airport express to my existing airport express at home so I can extend the wireless range and also to connect my printer (to my second airport express) so I can have a shared wireless printer. Is this possible? If so, can someone assist me on how to set this up?
Thanks.

Try the following ...
AirPort Express Base Station (AX) - WDS Setup
"Factory Reset" the AX base stations
o (ref: http://docs.info.apple.com/article.html?artnum=108044)
(Note: To facilitate setting up the base stations, place them in near proximity of each other during the setup phase. Also record the Apple IDs of each base station that will included in the WDS as these will be required during setup.)
Main Base Station Setup
(Note: The AX connected to the Internet will be assumed to be the main base station in the WDS.)
Either connect to the AX's wireless network or by temporarily connecting directly, using an Ethernet cable, to the Ethernet port of the AX, and then use the AirPort Admin Utility to make the following settings.
WDS Tab
1. Enable this base station as a WDS: main base station (checked)
2. Allow wireless clients on this base station (checked)
3. Click "+" to add Remote/Relay Base Stations.
3a. Select the Base Station that you want to be the WDS Remote/Relay.
3b. AirPort ID: <verify that this is the correct MAC address for the Base Station you are adding as a Remote/Relay.>
3c. Auto configure as a WDS remote base station (checked)
3d. Click "OK."
4. Verify that the Remote/Relay Base Station has been added to the list.
5. Click "Update," and then verify the settings for the Remote/Relay.
5a. Allow wireless clients on this base station (checked)
5b. New network name: <verify that this is the same as the network name as the main base station>
5c. TCP/IP: Configure using DHCP
5d. Base Station Password: <the Remote/Relay Base Station password>
5e. Confirm: <same as previous step>
5f. Click "OK."

Extend wifi range with 2 airport express

I currently have an airport express on my main floor for wifi, can I add another airport express on 2nd floor to extend the wifi range if both of them are connected to a wired ethernet switch?

Yes. If you are using AirPort Utility 6.x on a Mac or AirPort Utility on an iPhone or iPad, the setup is a breeze, and will take about 2 minutes.

Extend wireless network with multiple airport express and netgear powerline

I currently have the following network configuration:
1. Using ATT u-verse (2-wire 3800HGV-B "modem") to internet
2. Disabled the u-verse modem wireless router, and have connected an Apple Time Capsule wireless router (on a DMZ)
3. Have four Netgear XAVB5001 powerline adapters connected to the time capsule (for our iMac desktops and the Apple TV)
4. Have an Airport Express wirelessly connected to the time capsule to extend range (for our iPhones and iPad)
All this is currently working. What I would like to do is the following, keeping 1-3 above the same:
4. Connect the airport express to the time capsule via Netgear XAVB5101 powerline adapter (instead of wirelessly connecting to the time capsule as it is today) and use it to extend the wireless range of the time capsule
5. Add ANOTHER airport express to the time capsule via powerline adapter (and extend the wireless range elsewhere in the house).
Does anyone have any experience with this kind of setup and can assure that it would work? (I'm trying to decide whether to spring for a couple more powerline adapters and another airport express)
Thanks in advance!
Dave

I had a VERY similar problem: I was trying to extend my wireless network using a hardwired ethernet connection from Airport Extreme to my Time Capsule. Every time I plugged in the wire to the TC, everything disappeared. Unplugged, and boom. Came back.
Here's how I solved it:
Go into Airport Utility and select the unit you are trying to use as a wireless extender and choose to edit it. Then, on the wireless tab select CREATE a wireless network. But, give it the exact same name and password. This is completely counter-intuitive. You would think to choose EXTEND, but this would be wrong. Next choose the network tab. And, select Router mode to Bridge (off).
By choosing the same name and password, your phone, laptop, etc. will think it's on the same network and move seamlessly from one to the other.
See if this fixes your issue. Fixed mine instantly. AND, it only took 3 painstaking hours of checking ethernet connections and rewiring jacks, etc. to figure it out. LOL

How do i extend my network with a airport express

How do I extend my network with mt airport express

Hi Tesserax, I'd like to join this discussion. It seems Jasonbeyer didn't reply, but I have a question related to his.
I'd like to extend the wireless signal from my Cisco Model DPC/EPC2202 VoIP Cable Modem (802.11n) to the living room where, at the moment, it is non-existent. I assume there's inteference or the signal cannot reach through the concrete walls and rooms leading up from my bedroom to the living room.
My question is:
I'm thinking of extending my wi-fi signal by using the Airport Express and simultaneously using it to connect to my hi-fi to play iTunes from my bedroom's iMac.
Something's telling me it's not going to be that easy. I'm using an iMac (7,1) if that's any help or clue.
What are the things I should take note of and will Airport Express be compatible with my modem? Would I have to get TWO Aiport Express to bridge the signal to my living room?
Thank you everyone for your time. Cheers!
Kane

Help! Im trying to extend the network on my Airport Extreme with an Express

This is probably such a begginers question but it has truely boggled my mind for the last 24 Hours!
I have brought an airport express to extend my airport extreme network. My Airport extreme is the base and is hooked up to my initial Home model from my ISP which works fine.
I have been trying to connect my airport express and am having no luck. I have plugged the airport in but am having no luck locating it on my airport utility (only my actual Airport Extreme shows)
Can someone please help me Ive been here for hours reading on forums trying to sort this out and Im gettin nowhere fast!
The light on the express is flashing orange. I have tried to reset it but there still is nothing showing.
any ideal on what i could do or follow step by step?

Ok, the question is how can i extend the range with
my airport extreme base,
With an Airport Express or another Airport Extreme
I have A netgear WNP802, it
has a repeating feature.
Which won't work with your Airport Extreme
< But i am wanting to have the
netgear and the apple airport extreme talk to each
other so that i can put the net gear in a seperate
room to extend the range of signal. </div>
This is not possible.
How can i do this?
You can't.
Netgear and Apple use different chips which means they won't and can't talk to each other when it comes to extending networks.

Extending a network with 2x Airport Express

I tried searching and couldn't find any discussions which answered my question. We have a home office which was just completed (an actual, separate structure, not just a room) and I need to connect it to the main house where our Internet connection comes in. What I'm trying to do is use an Airport Express (802.11n), which wirelessly connects to the main router, an Airport Extreme (802.11n, 2nd gen.). This Airport Express is then connected via Cat5e cable and a gigabit switch (it's a pretty long run) to another Airport Express (802.11n). This second Airport Express will then reconvert the connection to wireless and allow us to connect our devices in the office to the rest of the network and get access to the Internet.
Here's a crappy diagram I drew in Paint: http://i.imgur.com/5KrhX.png
When I first connected the second Airport Extreme in the office, I got a pop-up showing the new device in Airport Utility. However, no matter how I configure it, I cannot successfully get it to join the network properly. I've gone through the process multiple times, but am not having any luck. I've attempted to get it to "join my existing network" and then specify to connect via Ethernet and extend my network, and then tell it which device (the first Airport Extreme) it's connected to via Ethernet. Once I try to commit the changes, though, the device restarts and ends up with a blinking orange light, disappearing entirely from the list of devices in Airport Utility.
I've checked and the Airport Extreme is set up to allow devices to extend the network, and I've tried setting the first Airport Express to both "Join my wireless network" and "Extend my wireless network," though neither seems to make a difference.
Am I missing something, or trying something that won't work? Any ideas?
Thanks!

When I first connected the second Airport Extreme in the office, I got a pop-up showing the new device in Airport Utility. However, no matter how I configure it, I cannot successfully get it to join the network properly. I've gone through the process multiple times, but am not having any luck. I've attempted to get it to "join my existing network" and then specify to connect via Ethernet and extend my network, and then tell it which device (the first Airport Extreme) it's connected to via Ethernet.
You have two choices with AirPort Express #1:
Configure the AX as a wireless Ethernet bridge. Apple calls this configuration a ProxySTA. In this configuration, the AX would join the wireless network provided by the AirPort Extreme, and then, share this connection out it Ethernet port to the Ethernet switch.
Configure the AX to extend the wireless network of the AirPort Extreme. This would also enable the base station's Ethernet port.
Of the two, I would recommend the first option.
To configure the AX as a ProxySTA, you need just to make the following two setting changes:
Wireless Mode = Join a wireless network
Allow Ethernet clients (enabled)
Both of these settings are on the Wireless tab in the AirPort Utility.

What kind of range extender can I use with airport express

WHat kind of range extender can I use with an airport express?

WHat kind of range extender can I use with an airport express?
Use any router that you want if you will be connecting the extender/router back to the AirPort Express using a permanent, wired Ethernet cable connection.
If you are planning to use a wireless connection to extend the range of the network.....then another AirPort Express, AirPort Extreme or Time Capsule will be required.

Extending a time capsule with airport express twice

Hi,
I have been trying to extend my existing wireless network recently but it never ended up how I wished...
I have one 4th generation Time Capsule (A1409) and two Airport Express 802.11n (1st generation A1264).
All currently have MAC Address base authentication and no security in place for was of testing (security not relevant at this point in time).
When I extend my Time Capsule with either Airport Express this works like a charm, the LEDs are all green and connection works for client devices.
When I extend my Time Capsule with both Airport Express the same applies, everything works.
However what I have found not to works it extending my Time Capsule with one Airport Express and then extending this Airport Express with the second Airport Express. While all LEDs are green and the second Airport is seen in the Airport Utility, I find no client are ever able to connect to it and alway either connect to the first Airport Express or to the Time Capsule. This is an issue I the area I want to cover is pretty big and I need the second Airport Express for the additional reach.
I haven't found anything against this setup, it however appears you can't connect to the second Airport. The Airport Utility would even accurately depict the situation with Airport Express one dotted line to Time Capsule, and Airport Express two dotted line to Airport Express one.
However no connection seam possible to Airport Express two.
I have swapped Airport Express one and two, and in this case Airport Express gets the clients and Airport Express one now extending Airport Express two gets none.
Is this an expected behavior, i.e. should I give up or is there anything I can do about this ?

However what I have found not to works it extending my Time Capsule with one Airport Express and then extending this Airport Express with the second Airport Express.
Apple's "extend a wireless network" feature will only allow you to extend the signal one level, not two. It's possible to have more than one device extending the signal, but each extender must connect directly to the main base station.....not to another device that is already extending the signal.
The Airport Utility would even accurately depict the situation with Airport Express one dotted line to Time Capsule, and Airport Express two dotted line to Airport Express one.
This is an illusion. AirPort Express is "joining" the wireless network.....not extending it. When the Express "joins" a network, it can be used for AirPlay, or a remote printer could be connected to the USB port, but the Express will not provide any additional wireless signal coverage when it joins a network.
Is this an expected behavior
Yes. I can try to look up Apple's support document that explains this if you want more information, but you may likely already have all the information that you need. Let us know.

Extending wireless network with an aiport express

I have a netgear wireless router set up in my house on the second floor, but my room being located on the first floor i get a poor signal so i bought an airport express to extend my network. i tried going through the aiport exress setup assistant but that wouldnt work, so i ended up hooking it to my netgear router on the second floor to set it up in airport admin utility and then brought it back down to the first floor. my itunes worked with the speakers for about.. ten seconds then stopped. and my signal is just as weak as before.. any suggestions?

Unfortunately, it is simply not possible to use an Airport Express to wirelessly "extend" the wireless range of any model of Netgear wireless router. Netgear's wireless routers do not support Apple's implementation of a wireless distribution system (WDS), which is a necessary requirement for setting up an extended wireless network with the Airport Express. And no - it doesn't work the other way around either (Airport Express as base station, Netgear wireless router to "extend").
It sounds like you did successfully configure your Airport Express to "join" your existing wireless network - which will allow you to print and stream iTunes to the Airport Express. The problems you are having with Airtunes "hanging" on your Mac are almost certainly due to the poor wireless signal quality problem that you are already aware of.

How to connect old aiport express to my new Airport Extreme? My Ipad says "base station e5713b cannot be configured" and my AirPort tool on my PC will not permit me to add my new Airport Extreme network (no network names to choose from)

How to connect old aiport express to my new Airport Extreme?
I have a PC running with Win7 and just replaced my Jensen With a brand New Airport Extreme.
I have set up the Airport Extreme to the internet, Iphones and Ipads and it work as it should.
I have downloaded latest Version of Airport tool on my PC. In addition i have downloaded the airport tool for Ipad.
I have reset one of my airport Express and it now shows up both on the Ipad and on the PC airport tool.
My Ipad says "base station e5713b cannot be configured."
I have wired the airport Express to my Ethernet to be able to "see it" on my Airport tool.
My AirPort tool on the PC will not permit me to add the airport Express to my new Airport Extreme network (no network names on the drop-down list to choose from). I wished for an easy set-up, but nothing seems to be plug and play as the Commercial says.. can you please help me?
Sigve

Hi
Thanks for Swift reply.
Yep - I in fact have two A1088 and one A1264
I actually bought the new router because the Jensen
router always lost connection to the Airport Express after some hours or days. I
always needed to restart my Jensen to play music and that was driving my wife
mad. The hope was that the Extreme should fix this. Both A1088 have been set up
to only stream music to two of my stereo amplifiers from my PC’s Itunes library.
Are the A1088 now useless?
The A1264 has been set up to feed internet into a Denon Reciever that needed Ethernet cable.
Please advise
Regards
Sigve

My wi-fi worked fine on Airport Express two days ago. Now the light is green, but I can't get the Internet on my satellite connection. I've checked Network Preferences, Aiport Express menu, and the satellite tech support. The Ethernet connection works.

My wi-fi connection from my iPad via the Airport Express Base Station on my home computer worked just fine until yesterday morning. I have a Macintosh G5 with a satellite connection. I could not get an Internet connection. After using the Network Preferences and Aiport Express applications several times, then unplugging and replugging in the computer, satellite modem and Airport Express module, checking the satellite dish for any obstructions, and so on, the computer still wouldn't connect to the Internet. (The green light was on in the Airport Express module.) I called the satellite company technical support division last night. The tech couldn't find any problem with the satellite connection. When I plugged the satellite modem cord directly into the Ethernet outlet on my computer, I could pick up the Internet.
Today, the Airport Express module still has a green light but still doesn't connect to the Internet. The only thing I can think of is that lights went out for about 15 minutes yesterday morning. All of my electronics, except the Aiport Express Base Station, are on surge protectors. Why would the Airport Express module still have a green light if it was damaged by the electrical outage?
I bought the module in 2009. I have never had problems with Apple equipment before this. Is this base station fixable?
I would appreciate your suggestions.

Hello everyone. I too have experienced the same problem Mary described starting on the same day she mentioned January 12. I have a G5 iMac, a G5 mini-mac, and a G4 laptop. They were all working fine but all have mostly the same problem now in that the G4 does not connect at all and the G5s connect once in a while after restarts but do not maintain the connection. In my case there was no power interruption. In fact, the G4 laptop was not even connected to the home power connection. My iPad2 and iPhone 4s wireless work fine and a wireless PC and Android tablet work fine as well. The G5 and G4 work fine on an ethernet connection. ISP tech support (AT&T u-Verse) was very generous with their time in trying to solve my problem although it was established early on that their connection and equipment was working fine and that the problem was with my computers. They walked me through a manual reset of all the particulars on IP addresses etc. so the problem was not related to that either. In the end ISP tech support concluded that the problem must lie with the Airport driver. For some reason it changes the IP addresses to an incorrect address so it cannot connect. Indeed when I tried the diagnostics on the G4 I got a window Pop-up that said an application had reset my settings. (In retrospect I seem to recall that I may have gotten that same message early on with the G5s but at that time I did not think much about it and went about trying to reset the settings but that process never concluded well) I think that the problem may be that there must have been an update of the Airport software that was not backward compatible with the G5 and older Macs. I mention all this for two reasons. First, perhaps someone out there who knows better than I do how to bring this to Apple's attention and perhaps they will address this. Second, I would be curious to know whether there is anyway one can return a configuration on Macs to some earlier time period (as you can on PCs) when everything worked and then leave it that way foregoing any subseqent upgrades or any subsequent apps?

Why can't the newest Airport utility program find my Aiport Express 1st generation? Anybody have an idea?

Why can't the newest Airport utility program find my Aiport Express 1st generation? Anybody have an idea?

Windows XP SP3, Vista SP2, 7 SP1 use......AirPort Utility 5.5.3 for Windows - Support - Apple
Windows 7 or higher use.....AirPort Utility 5.6.1 for Windows - Support - Apple

Extending aiport express to another airport express

Similar Messages

Maybe you are looking for