Extending an existing wireless network using Time Capsule

I connected my Time Capsule via Ethernet cable to my network. I used the airport utility to extend my existing wireless network (Cisco router)k. After that my wireless devices were disconnected and I got a message stating "Unable to join wireless network". The macbook that I used to set up the Time Capsule showed a message along the lines that a device on the network was trying to use the macbook's IP address, I changed the macbooks IP address and then was able to connect my ipad and iphone to the wireless network but the connection was unusable as it was so slow. has anyone done this successfully and if so do you have nay advice

If you connect the TC to the network by ethernet you do not extend an existing networking.. indeed you cannot.. only works with apple routers and no ethernet.
You create a wireless network.. you can use roaming .. ie use the same wireless name and security settings as the existing Cisco router but you must set different channels.
If you need instructions in that setup what version airport utility are you using. I would strongly recommend a version 5.. it is so superior cf toyland v6.

Similar Messages

How do I extend an existing wireless network using airport express?

Hi all,
I am trying to extend existing wireless network using airport express, my main router is Belkin

Unfortunately, Apple's "extend" feature is designed to only work with other Apple routers if you are trying to "extend" using wireless only.
It is extremely unlikely that this feature would work with a router from another manufacturer using wireless only.

Extending wireless network using Time Capsule

Hi guys,
I have been trying to sort this issue out for some time.
Basically I have a Thompson Wireless Router which connects to my ISP, this is downstairs broadcasting a wireless network to my house.
I want to put the Time Capsule upstairs, to extend the WLAN and also connect my Xbox over Ethernet.
No matter what I try I cannot get it to work, it ends up setting up 2 WLANs where the Thomson WLAN works (as there is an ISP connection) and the TC wont (as its not connected)
What I want is for the Thomson WLAN to be extended via the TC to allow my Xbox on to Live...
I also have a Mac Mini upstairs that would connect either via the TC WLAN or through ethernet.
Any help you can offer would be amazing
Thanks
Adam

If you are trying to "extend" the wireless signal from the Thompson router through the Time Capsule using wireless only, this is probably not going to work.
The reason for this is that Apple's "extend a wireless network" feature appears to be a proprietary technology that works only among other Apple devices. For that reason, it is highly unlikely that the Thompson router and Time Capsule would be compatible for the purpose that you desire.
If you are able to connect the Time Capsule to the Thompson router using an Ethernet connection, you could configure the Time Capsule to "create a wireless network" using the exact same wireless network name, security settings and password as the Thompson network. In addition, the Time Capsule must be configured as a "bridge" in Bridge Mode for this to work correctly.
If you cannot run the Ethernet cable, you might want to look at a pair of Etherent powerline adapters to accomplish the same task by sending the Ethernet signal over the existing AC powerlines in your home.

I have a m2007 macbook connected to my wireless network using time capsule. I stream video to the macbook, but often get start stop of the streaming, but no wheel to indicate a buffering issue. Can I resolve this with higher speed internet and cable mod

I'm wondering if my cable internet is too slow for wireless streaming of videos to other macbooks. Any help will be appreciated

Can you clarify whether you are asking about video that you are streaming from the Internet to your Mac through the Time Capsule?
Or, are you asking about streaming video that is already stored on the Time Capsule to your Mac?
In either case, what happens....video quality wise..... if you test by temporarily turning off the wirelss on the Mac and then connecting it to one of the LAN <-> ports on the Time Capsule using a spare Ethernet cable for a few hours?

Extending an existing wireless network using an Airport Extreme (dual band 802.11n)

Hello,
I currenlty have a wireless network set up inside my apartment using a Linksys E1000 wifi router. I would like to extend the network into a second room using my airport extreme. However, I have tried to set up the airport extreme to extend a network and it tells me that it cannot extend my currently network. I have already restored my airport extreme to its factory settings (using the reset button on the back of the airport extreme) as I used to use the airport extreme as the main base station in my previous apartment.
Help please!

Unfortunately, Apple's "extend a wireless network" function was designed as a proprietary feature that only works with other Apple routers.
It would be extremely unlikely that it would work with a router from another manufacturer if you are trying to "extend" using wireless only.
Suggest that you use another Linksys "repeater" or "extender" to insure compatibility with your current router.

Hi I am hoping to add my 2 TB time capsule to my existing wireless network using cisco dpq 3925 modem. I have two mbp one running Yosemite and the other os 10.7.5

I have a time capsule 2TB model 1409. I would like to connect it to my existing wireless network (using a cisco DPQ 3925 modem). I have two mac book pro one running Yosemite and the other OS 10.7.5. The best I can do is to connect the TC to the Modem via ethernet. Have one of my MBP connect to the time capsule using a ethernet cable and have the TB set to bridge mode. In this configuration, both mbp and the iPad can detect the TC but when I try to connect it to the wireless network, using the same network name and password, the light flashes amber and I cannot detect the time capsule again.

Correct..
The best I can do is to connect the TC to the Modem via ethernet.
The TC does not connect to non-apple routers by wireless.. well. It is possible but so poor a method that Apple seem to have eliminated it in the setup wizard.. I would take that as a good thing..
If you cannot use ethernet you have two choices..
Use another apple router that is plugged into the Cable modem.. eg a second hand Extreme Gen5 or the latest Express.. the Extreme is both cheaper and better.
Or you can use a set of EOP (homeplug) adapters.. but they cannot be guaranteed to work so you should buy from a place that allows returns.

Troubling extending wireless network with Time Capsule and Airport Extreme

I am trying to set up and extend a wireless network in my house, but it’s not working right. I have two Airport/Capsule units in the house:
2TB Time Capsule (Dual-Band II)
1 Airport Extreme (Dual Band)
I have the Verizon Fios router as my gateway to the internet, and also as my DHCP server. I have also tested the ethernet ports in my house to verify that they work, and that I can get a DHCP-issued IP address.
Now, my Verizon router has WiFI, and it’s still on. I am not using it though except to troubleshoot. So far as I understand, this should not cause a problem.
Base station setup
So I setup the TC to Create A New Wireless Network, on the ethernet network it’s on (Dlink switch plugged into Verizon router). I set it up in Bridge Mode (as opposed to having it dole out IPs, since the Verizon router does this already). The TC gets a valid IP, and my wireless device connect to it without a problem. I have checked “Allow this network to be expanded” under Wireless settings.
Extended station setup
The AE Dual-Band is plugged into the Ethernet, and is reset to Factory Settings. I name it “Airport Extreme 2” and I chose “I want Airport Extreme to join my current network.” The other two options are: “I want to create a new wireless network” and “I want to replace and existing base station or wireless router with Airport Extreme.”
I chose to “join,” I select “I want to connect Airport Extreme to my network using Ethernet to extend my existing wireless network.” The other options are to disable wireless entirely, or to “wirelessly join my current network.” On the next page it asks me to select the device or network that the Airport Extreme will connect to using the Ethernet. I set it to the Time Capsule.
Results:
Access near the Airport Extreme 2 is incredibly slow. Speedtest shows I am getting less than 1Mbps. Worse yet, my mail client won’t connect. It just times out.
What I had hoped was that the AE would connect via Ethernet to the network, and just bring the wireless network to the other side of the house. Instead it almost seems as though it is just re-amplifying the TC’s signal. Otherwise, why is performance so bad?
Thanks to anyone with some insight here!

Hello Kennuff. Welcome to the Apple Discussions!
Since you have the ability to connect all of the routers by Ethernet, there is no need to configure the Time Capsule (TC) & 802.11n AirPort Extreme Base Station (AEBSn) for a dynamic WDS (aka, extending a network). This option is only when the routers do NOT have an Ethernet connection between them.
Instead, you want to configure the TC & AEBSn in a "roaming" network. I suggest starting by performing either a "hard" or "factory default" reset on both.
Next be sure that both the TC & AEBSn are on the same Ethernet subnet coming from the Verizon-supplied router.
Configure the TC & AEBSn as follows:
AirPort Utility > Select the TC or AEBSn > Manual Setup > AirPort > Wireless
o Wireless Mode = Create a wireless network
o Allow this network to be extended: <not checked>
o Radio Mode: <leave the default or if you require a specific mode make sure both routers are configured the same>
o Wireless Security: <configure both routers the same>
AirPort Utility > Select the TC or AEBSn > Manual Setup > Internet > Internet Connection
o Connection Sharing = Off (Bridge Mode)

How can i extend a wireless network with time capsule

How can i extend an existing wifi verizon wireless network with time capsule? the router is connected on the bottom floor. want to boost the signal to a home office on the top floor, four flights up. connect time capsule via ethernet cable to iMac on 4th floor? Do I have to start a second wifi network or can I set it to just boost the one I have? thank you

How can i extend an existing wifi verizon wireless network with time capsule?
It all depends on what you mean by "extend".
If you plan to "extend" by connecting the Time Capsule to the Verizon router using a wired Ethernet cable, this can be accomplished.
If you were hoping to connect the Time Capsule to the Verizon router using wireless only, unfortunately the Time Capsule and Verizon products are not compatible for that purpose.
Check with Verizon to see if they offer an "extender" or "repeater" that could be located very close to the Time Capsule.
This would provide both more wireless coverage and also allow you to connect the Time Capsule using an Ethernet cable from the "extender" or "repeater".

How can I set up a guest WiFi network using Time Capsule and Airport Express extension?

How can I set up a guest WiFi network using Time Capsule and Airport Express extension?

Sorry, but it is not possible to "extend" the Guest Network using either wireless or an Ethernet connection.

I am trying to extend my existing wireless network

I am trying to extend my existing wireless network beyiond an extreme and an express by adding a further express. Is this possible?

This is not possible if you are trying to do this wirelessly, as Apple's "extend a wireless network" feature will only allow the signal to be extended one time.
It is possible to have more than one device extend the network, but each extender must communicate directly to the AiPort Extreme....not to another extender.

How do I extend an existing wireless network with a 2nd time capsule? I want to tether them with a gigabit ethernet connection.

I am having trouble with extending a wireless network using 2 timecapsules (1 is 1 terrbyte hdd, the other has a 2TB HDD.) The first one is connected to the WAN (cable modem) and our LAN. I would like to connect the 2nd one to the ethernet LAN and have it 'rebroadcast' the 1st ones wireless n network in order to expand the overall range of the network. Your help is very much appreciated.

Suggest that you download and install the much more useful AirPort Utility 5.6 for Mac OS X Lion.
I assume that Time Capsule 1 is operating correctly at this time.
Open Macintosh HD > Applications > Utilities > AirPort Utility 5.6
Select Time Capsule 1 and click Manual Setup
Click the Wireless tab below the row of icons and make a note of each of the setttings on this Wireless page.
Make sure that the Ethernet cable is connected to the WAN "O" port on Time Capsule 2.
Open up AirPort Utility and select Time Capsule 2 and click Manual Setup
Click the Wireless tab below the icons and enter the exact same settings that you wrote down for Time Capsule 1
Click the Internet icon, then click the Internet Connection tab
Make sure that the settings look like this:
Connect Using = Ethernet
Connection Sharing = Off (Bridge Mode)
Click Update and allow 25-30 seconds for Time Capsule 2 to restart to a green light
Very important......perform a power cycle of the entire network as follows:
Power off every device in any order that you wish
Wait a minute
Power up the modem and let it run for minute by itself
Power up Time Capsule 1 the same way
Power up Time Capsule 2 the same way
Continue starting devices one at a time the same way until the entire network is back up

Wireless Printing using Time Capsule

I tried to print wirelessly but I keep getting the message: There is a problem communicating with the printer. What am I not doing?

I have had similar difficulties trying to get my HP 460wbt to connect wirelessly to the Time Capsule. It works fine if you take off any wi-fi security (a useful thing to check compatability but probably not wise to leve the network open!).
I previously used an Airport base station and though I had some initial difficulties I did manage to use WEP security on that and it worked faultlessly with any computer attached to my network including Windows XP via Parallels. HOWEVER, I couldn't get WEP to work with the Time Capsule and printer (it worked with the computers) and WPA/WPA2 is I suspect not compatible with WPA_psk (or at least I can't figure this one out!).
The conclusion then is that the wireless card/software security for the printer isn't going to work with the Time Capsule - a pity and rather odd since there is a work round with the Airport base which is at least 5 years old! Why do Apple not make such issues backwards compatible I wonder?
I have solved the problem temporarily by having BOTH the Time capsule and Airport base connected wirelessly - which means a one click change of wireless network to print - but hey-ho it works until I find another solution. Any ideas?

Extending an existing wireless network with an airport express

My wireless signal is quite weak in my room so I'm looking for a way to extend the range of the network by using an airport express. I understand i can't do this wirelessly but is it possible to run an ethernet cable from my existing router to the airport express in my room and then have a stronger signal in my room?
Thanks in advance!

Welcome to the discussion area, Aaron!
If you connect an ethernet cable from your existing router to the AirPort Express, and then configure the Express to "Create a wireless network" with the same name, security settings and password, this will in effect, extend your current wireless network.
The Express must be configured as a "bridge" to operate correctly on your network when you do this, meaning that the setting for Connection Sharing on the Express will be set to "Off (Bridge Mode).

Connect to Existing Wireless Network Using AE and 2WIRE Home Portal

I would like to use my airport express to connect to an existing wireless network set up in my place, I got a pc wireless network connected with a 2Wire Homeportal 1000HW.
I've tried with the Assitant in both options, just joining the network to play music or joining the network to extend the range and nothing works, always the AE disappears.
Can I do that with my home portal or I need a different one?
If I need a new one what should I buy, my provider is SBC (DSL)
HP Pavilion zv6000 Windows XP

I am on a Mac and can do this with my 2Wire 1000SW. Not sure what the difference is, but I imagine it's just speed (mine is 802.11b). The reference to another posting on the 2Wire says that you must disable WEP. I have all my security still in place. When I run the setup utility and ask it to join my existing network (2Wire Network), it asks for my WEP and runs from there.
Were you able to get this to work?

Connect to Existing Wireless Network Using Airport Express?

I would like to use my airport express to connect to an existing wireless network set up in my apartment. The wireless router (linksys) is set up in my roommate's room to his desktop. I have a printer in my room and would like to use the airport express to connect to this existing network so that my roommates and i can print wirelessly. I need to keep the printer in my room.
Is there a way to do this? Please advise.
Thanks.

Is the LinkSys a WRT54G? If so, you have two options. If not, only the first option below is available to you:
1. You can configure the Express to connect as a wireless client. You won't be able to connect wirelessly directly to the Express in this mode; you have to connect through the router.
2. With the proper firmware in the WRT54G, you can set up a Wireless Distribution System (WDS). In this configuration, not only can the Express be used for printing and AirTunes, but it will also extend the range of your wireless network.

Extending an existing wireless network using Time Capsule

Similar Messages

Maybe you are looking for